Synthesis and radical polymerization behavior of bifunctional vinyl monomer derived from N‐vinylacetamide and p‐chloromethylstyrene

The radical polymerization of N‐(p‐vinylbenzyl)‐N‐vinylacetamide ( 1 ) prepared by the reaction of N‐vinylacetamide with p‐chloromethylstyrene was carried out by using radical initiators such as AIBN or BPO in benzene, chlorobenzene, or bulk. As a result, poly 1 was successfully isolated by dialysis (yield, 10–36%). The crosslinking reaction of poly 1 was carried out at 60–100 °C for 8 h. By using a radical initiator such as AIBN or BPO (3 mol %), the crosslinking reaction proceeded (yield, 63–79%). Moreover, the crosslinking reaction of poly 1 proceeded at 100 °C without a radical initiator in 50% yield. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2714–2723, 2006     

Preparation of poly(styrene‐co‐acrylonitrile)‐grafted multiwalled carbon nanotubes via surface‐initiated atom transfer radical polymerization

The in situ grafting‐from approach via atom transfer radical polymerization was successfully applied to polystyrene, poly(styrene‐co‐acrylonitrile), and polyacrylonitrile grafted onto the convex surfaces of multiwalled carbon nanotubes (MWCNTs) with (2‐hydroxyethyl 2‐bromoisobutyrate) as an initiator. Thermogravimetric analysis showed that effective functionalization was achieved with the grafting approach. The grafted polymers on the MWCNT surface were characterized and confirmed with Fourier transform infrared spectroscopy and nuclear magnetic resonance. Raman and near‐infrared spectroscopy revealed that the grafting of polystyrene, poly(styrene‐co‐acrylonitrile), and polyacrylonitrile slightly affected the side‐wall structures. Field emission scanning electron microscopy showed that the carbon nanotube surface became rough because of the grafting of the polymers. Differential scanning calorimetry results indicated that the polymers grafted onto MWCNTs showed higher glass‐transition temperatures. The polymer‐grafted MWCNTs exhibited relatively good dispersibility in an organic solvent such as tetrahydrofuran. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 460–470, 2007     

Surface modification of multiwalled carbon nanotubes via nitroxide‐mediated radical polymerization

The nitroxide‐mediated radical polymerization of styrene was carried out on the surfaces of multiwalled carbon nanotubes (MWNTs) initiated by an MWNT‐supported initiator multiwalled carbon nanotube–2″,2″,6″,6″‐tetramethylpiperidinyloxy (MWNT–Tempo). The content of polystyrene grafted from the surface was controlled by changes in the polymerization conditions, such as the reaction times or the ratios of monomers to initiators. The obtained polystyrene‐grafted multiwalled carbon nanotubes (MWNT–PSs) were further used to initiate the polymerization of 4‐vinylpyridine to get polystyrene‐b‐poly(4‐vinylpyridine)‐grafted multiwalled carbon nanotubes (MWNT–PS‐b‐P4VPs). In contrast to unmodified MWNTs, MWNT–PSs had relatively good dispersibility in various organic solvents, such as tetrahydrofuran, CHCL₃, and o‐dichlorobenzene. The structures and properties of MWNT–PSs and MWNT–PS‐b‐P4VPs were characterized and studied with several methods, including thermogravimetric analysis, Fourier transform infrared, ultraviolet–visible, and transmission electron microscopy. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4656–4667, 2006     

Polarons radical polymerization

Polystyrene has been typically prepared with radical polymerization by benzoyl peroxide (BPO) or azobisisobutyronitrile (AIBN). In this report, polymerization of styrene was carried out by radical cations of polyaniline (PANI). Polarons of conducting polymers are consisting of radical cations. The polarons bear electrical conduction as a charge carrier. We employ the polarons as an initiator for radical polymerization. Polymerization of styrene and acrylonitrile by the polarons was conducted to explore new possibility of conducting polymers. Fourier‐transfer infrared absorption (FTIR) spectroscopy measurements for the resultant polymers obtained with polarons of polyaniline indicates that the polystyrene thus synthesized grows from polyaniline. The qualitative solubility, average molecular weight, and thermal stability are comparable to that of polystyrene obtained by the common method with BPO. Radical polymerization by polarons may provide a new avenue for radical polymerizations through application of conducting polymer. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 805–811     

Chemical initiation of graft copolymerization of methyl methacrylate onto styrene–butadiene block copolymer

When a solution containing both styrene–butadiene block copolymer (SBS) and methyl methacrylate is treated with an initiator both homopolymerization of the methyl methacrylate and graft copolymerization of the methyl methacrylate onto the SBS occur. The amount of graft copolymerization depends upon the time and temperature of the reaction, the concentrations of all species, and the identity of the solvent and initiator. The combination of benzoyl peroxide in chloroform gives the highest graft yield and the reaction occurs by removal of an allylic hydrogen from the SBS by the initiator radical and subsequent addition of monomer units to that site; there is a significant solvent effect. Both AIBN and BPO function by the removal of an allylic hydrogen atom from SBS; BPO is able to effect this reaction relatively easily while AIBN can remove the hydrogen atom only with great difficulty and to a limited extent. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 965–974, 1997     

Reversible addition–fragmentation transfer polymerization of p‐nitrophenyl acrylate and synthesis of diblock copolymers poly(p‐nitrophenyl acrylate)‐b‐polystyrene

Poly(p‐nitrophenyl acrylate)s (PNPAs) with different molecular mass and narrow polydispersity were successfully synthesized for the first time by reversible addition–fragmentation transfer (RAFT) polymerization with azobisisobutyronitrile (AIBN) as an initiator and [1‐(ethoxy carbonyl) prop‐1‐yl dithiobenzoate] as the chain‐transfer agent. Although the molecular mass of PNPAs can be controlled by the molar ratio of NPA to RAFT agent and the conversion, a trace of homo‐PNPA was found, especially at the early stage of polymerization. The dithiobenzoyl‐terminated PNPA obtained was used as a macro chain‐transfer agent in the successive RAFT block copolymerization of styrene (St) with AIBN as the initiator. After purification by two washings with cyclohexane and nitromethane to remove homo‐PSt and homo‐PNPA, the pure diblock copolymers, PNPA‐b‐PSt's, with narrow molecular weight distribution were obtained. The structural analysis of polymerization products by ¹H NMR and GPC verified the formation of diblock copolymers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4862–4872, 2004     

Relevance of a prereaction for the in situ NMP of styrene using the C‐Phenyl‐N‐tert‐butylnitrone/2,2′‐azobis(isobutyronitrile) pair

In this article, we compare two routes for carrying out in situ nitroxide‐mediated polymerization of styrene using the C‐phenyl‐N‐tert‐butylnitrone (PBN)/2,2′‐azobis(isobutyronitrile) (AIBN) pair to identify the best one for an optimal control. One route consists in adding PBN to the radical polymerization of styrene, while the other approach deals with a prereaction between the nitrone and the free radical initiator prior to the addition of the monomer and the polymerization. The combination of ESR and kinetics studies allowed demonstrating that when the polymerization of styrene is initiated by AIBN in the presence of enough PBN at 110 °C, fast decomposition of AIBN is responsible for the accumulation of dead polymer chains at the early stages of the polymerization, in combination with controlled polystyrene chains. On the other hand, PBN acts as a terminating agent at 70 °C with the formation of a polystyrene end‐capped by an alkoxyamine, which is not labile at this temperature but that can be reactivated and chain‐extended by increasing the temperature. Finally, the radical polymerization of styrene is better controlled when the nitrone/initiator pair is prereacted at 85 °C for 4 h in toluene before styrene is added and polymerized at 110 °C. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1085–1097, 2009     

Branched poly(styrene‐b‐tert‐butyl acrylate) and poly(styrene‐b‐acrylic acid) by ATRP from a dendritic poly(propylene imine)(NH2)64 core

With the aim of creating highly branched amphiphilic block copolymers, the primary amine end groups of the poly(propylene imine) dendrimers DAB‐dendr‐(NH₂)₈ and DAB‐dendr‐(NH₂)₆₄ were converted to 2‐bromoisobutyramide groups. Poly (styrene‐b‐tert‐butyl methacrylate) (PS‐b‐PtBMA) was synthesized by ATRP from the eight end group initiator, and poly(styrene‐b‐tert‐butyl acrylate) (PS‐b‐PtBA) was synthesized from the 64 end group initiator. The tert‐butyl groups were removed to produce poly(styrene‐b‐methacrylic acid) (PS‐b‐PMAA) and poly(styrene‐b‐acrylic acid) (PS‐b‐PAA). Comparison of size exclusion chromatography (SEC) absolute molecular weight analyses of the polystyrenes with calculated molecular weights showed that the eight end group initiator produced a polystyrene with about eight branches, and that the 64 end group initiator produced polystyrene with many fewer than 64 branches. The PS‐b‐PtBA materials also have many fewer than 64 branches. The PS‐b‐PAA samples dissolved molecularly in DMF but formed aggregates in water even at pH 10. AFM images of the PS‐b‐PtBAs spin coated from THF and DMF onto mica showed aggregates. AFM images of the PS‐b‐PAAs spin coated from various mixtures of DMF and water at pH 10 showed flat disks and worm‐like images similar to those observed with linear PS‐b‐PAAs. Use of a PS‐b‐PAA and a PS‐b‐PMAA as templates for emulsion polymerization of styrene produced latexes 100–200 nm in diameter. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4623–4634, 2007     

Synthesis and characterization of novel phosphonated and sulfonated poly(styrene–isobutylene–styrene) for fuel cell and protective clothing applications

A novel aromatic block–graft copolymer of sulfonated poly(styrene–isobutylene–styrene)‐graft‐poly(vinyl phosphonic acid) (SIBS‐g‐PVPA SO₃H) was synthetized for direct methanol fuel cell (DMFC) and chemical and biological protective clothing (CBPC) applications. The polystyrene (PS) blocks of SIBS were chloromethylated via a Friedel–Crafts reaction to obtain the macroinitiator SIBS‐CH₂Cl. Atom transfer radical polymerization (ATRP) was performed to graft VPA to the chloromethylated groups of the macroinitiator and yield SIBS‐g‐PVPA, which was subsequently sulfonated using acetyl sulfate as the sulfonating agent. After each functionalization step, a membrane was prepared by using the solvent casting technique. The final membrane was composed of triblock SIBS as the backbone, PVPA grafts attached to the chloromethylated PS end blocks and sulfonic groups in the non‐chloromethylated PS units. A comprehensive materials characterization study (e.g., GPC, FTIR, TGA, EA) was performed to confirm proper functionalization of each material. Unique ionic interactions (i.e., crosslinking via formation of sulfonate–phosphonium complexes) arose between the phosphonic and sulfonic groups (i.e., PO₃H₂ and SO₃H, respectively) that enhanced the water absorption capabilities, thermal and oxidative stability, and the transport properties of SIBS. The SIBS‐g‐PVPA SO₃H membrane presented high Nafion ® normalized selectivity and separation efficiency, indicating that this ionomer adequately functions for both applications. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1424–1435     

Acrylonitrile‐containing polymers via a combination of metal‐catalyzed living radical and nitroxide‐mediated free‐radical polymerization routes

2‐Phenyl‐2‐[(2,2,6,6‐tetramethylpiperidino)oxy] ethyl 2‐bromopropanoate was successfully used as an initiator in consecutive living radical polymerization routes, such as metal‐catalyzed living radical polymerization and nitroxide‐mediated free‐radical polymerization, to produce various types of acrylonitrile‐containing polymers, such as styrene–acrylonitrile, polystyrene‐b‐styrene–acrylonitrile, polystyrene‐b‐poly(n‐butyl acrylate)‐b‐polyacrylonitrile, and polystyrene‐b‐polyacrylonitrile. The kinetic data were obtained for the metal‐catalyzed living radical polymerization of styrene–acrylonitrile. All the obtained polymers were characterized with ¹H NMR, gel permeation chromatography, and differential scanning calorimetry. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3374–3381, 2006     

Dispersion polymerization of acrylamide: Part II. 2,2′‐Azobisisobutyronitrile initiator

Dispersion polymerization of acrylamide in tert‐butyl alcohol (TBA)‐water media (TBA ⩾ 50 vol %) using poly(vinyl methyl ether) (PVME) as the stabilizer and 2,2′‐azobisisobutyronitrile (AIBN) as the initiator at 50°C has been studied. The conversion‐time curve shows autoacceleration taking place from the very early stage of the reaction (measured from 4% conversion level). Molecular weight increases with conversion indicating that the gel effect is operative. This suggests that a major part (if not the whole) of the polymerization occurs in the particle phase. The effects of the concentrations of the stabilizer, the initiator, the monomer, and the solvent composition on particle size have been explained on the basis of particle phase polymerization. The feeding of the particles by the monomer presumably occurs through the solvent channels of the swollen particles. The swelling data of polyacrylamide films in various TBA‐water mixtures are given. The similarity and differences between the AIBN and ammonium persulfate (APS) initiated systems (published earlier by us) have been discussed. In general, particles are more polydisperse and bigger in the former case than in the latter. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 493–499, 1999     

Modification of Cross-Linked Rubber Particles by Free Radical Polymerization

The synthesis of polystyrene chains covalently bound to the surface of cross-linked rubber particles from recycled tires (ground tire rubber, GTR) was investigated via free radical polymerization in situ by using azobisisobutyronitrile (AIBN) and dibenzoyl peroxide (BPO) as initiators. Indeed, the graft polymerization provides a significant route to modify the physical and chemical properties of these particles allowing to improve their compatibility with other polymers. Polymerization reactions were carried out in bulk by changing the styrene/GTR ratio as well as the amount of free radical initiator. Appreciable amounts of polystyrene (PS) were grafted on GTR when BPO was used as confirmed by particle characterizations.     

Utilizing thiol–ene chemistry for crosslinked nickel cation‐based anion exchange membranes

Metal cation‐based anion exchange membranes (AEMs) are a unique class of materials that have shown potential to be highly stable AEMs with competitive conductivities. Here, we expand upon previous work to report the synthesis of crosslinked nickel cation‐based AEMs formed using the thiol–ene reaction. These thiol–ene‐based samples were first characterized for their morphology, both with and without nickel cations, where the nickel‐containing membranes demonstrated a disordered scattering peak characteristic of ionic clusters. The samples were then characterized for their water uptake, chemical and mechanical stability, and conductivity. They showed a combination of high water content and extreme brittleness, which also resulted in fairly low conductivity. The brittleness resulted from large water swelling as well as the need for each nickel cation to act as a crosslinker, necessary with the current nickel‐coordination chemistry. Therefore, increasing the ion exchange capacity (IEC) for these types of AEMs, important for enhancing conductivity, also increased the crosslink density. The low conductivity and brittleness seen in this work demonstrated the need to develop non‐crosslinking metal‐complexes. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 328–339     

Synthesis of tadpole polymers via triple click reactions: Copper‐catalyzed azide–alkyne cycloaddition,diels–alder,and nitroxide radical coupling reactions

We designed a trifunctional initiator ( 3 ) containing anthracene, bromide, and OH functionalities and subsequently used as an initiator in atom transfer radical Polymerization (ATRP) of styrene to yield linear polystyrene (PS) with α‐anthracene, OH, and ω‐bromide terminal groups, of which bromide is later transformed into azide to result in the linear anthracene‐, OH‐, and azide‐terminated PS (l‐α‐anthracene‐OH‐ω‐azide‐PS). The copper‐catalyzed azide–alkyne cycloaddition reaction between l‐α‐anthracene‐OH‐ω‐azide‐PS and α‐furan‐protected‐maleimide‐ω‐alkyne linkage, 4 afforded the linear anthracene‐, OH‐, and maleimide‐terminated PS. The cyclization via intramolecular Diels–Alder click reaction of this linear PS and the subsequent conversion of the hydroxyl into bromide resulted in the cyclic PS with one bromide located on the ring, (c‐PS)‐Br. Finally, the c‐PS‐Br was clicked with either well‐defined tetramethylpiperidine‐1‐oxyl‐terminated poly(ethylene glycol) (PEG) or poly(ε‐caprolactone) (PCL) yielding the tadpole polymer, (c‐PS)‐b‐PEG or (c‐PS)‐b‐PCL. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Templated nanostructured PS‐b‐PEO nanotubes

With anodic aluminum oxide (AAO) membranes as wetting templates, nanotubes of the cylinder‐forming polystyrene‐block‐poly(ethylene oxide) (PS‐b‐PEO) copolymer were generated. The PS‐b‐PEO solution was introduced into the cylindrical nanopores of an AAO membrane by capillary force and polymeric nanotubes formed after solvent evaporation. Because of the water solubility of the cylindrical PEO microdomains and the orientation of the cylindrical PEO microdomains with respect to the nanotube walls, the nanotubes were permeable to aqueous media. PS‐b‐PEO nanotubes were also prepared on the interior walls of amorphous carbon nanotubes (a‐CNTs). Because of the unique water permeability of the PEO microdomains, an avenue for functionalizing the interior of the a‐CNTs is enabled. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2912–2917, 2007     

DABCO‐functionalized polysulfones as anion‐exchange membranes for fuel cell applications: Effect of crosslinking

A series of DABCO‐functionalized polysulfones were synthesized and characterized. The effect that crosslinking has on the membrane properties containing different degrees of functionalization was evaluated. These polymers showed good thermal stability below the fuel cell operation temperature, T < 100 °C, reflected by the T_OD, T_FD, and thermal durability. The water uptake increased as the percentage of DABCO groups increased and the crosslinked membranes showed lower capacity to absorb water than the non‐crosslinked ones favoring thus the dimensional stability of the first ones. Membranes in the chloride form containing low degree of functionalization exhibited the highest tensile strength values. The ionic conductivity of non‐crosslinked membranes varied as a function of the functionalization degree until a value of around 100% achieving a maximum value at 86%. However, the crosslinked ones showed satisfactory ionic conductivities for values higher than 100%. The behavior of these polymeric materials in alkaline solutions revealed a great alkaline stability necessary to be used as solid electrolytes in fuel cells. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1326–1336     

Inverse gas chromatographic characterization of triblock copolymer of polystyrene–poly(ethylene oxide)–polystyrene

The thermodynamic properties of triblock copolymer of polystyrene–poly (ethylene oxide)–polystyrene (PS‐b‐PEO‐b‐PS) were investigated by means of inverse gas chromatography (IGC) using 15 different kinds of solvents as the probes. Some thermodynamic parameters, such as specific retention volume, molar heats of sorption, weight fraction activity coefficient, Flory‐Huggins interaction parameter, partial molar heats of mixing and solubility parameter were obtained to judge the interactions between PS‐b‐PEO‐b‐PS polymers and solvents and the solubility of the polymers in these solvents. It was found that increasing PEO content in PS‐b‐PEO‐b‐PS resulted in the increase in the solubility of PS‐b‐PEO‐b‐PS in alkanes and acetates solvents, but the solubility in alcohols had no change, and more PEO content in polymer caused a small decrease in the solubility parameter of PS‐b‐PEO‐b‐PS polymer, © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2015–2022, 2007     

Sulfonated polybenzimidazoles: Proton conduction and acid–base crosslinking

A series of soluble, benzimidazole‐based polymers containing sulfonic acid groups (SuPBI) has been synthesized. SuPBI membranes resist extensive swelling in water but are poor proton conductors. When blended with high ion exchange capacity (IEC) sulfonated poly(ether ether ketone) (SPEEK), a polymer that has high proton conductivity but poor mechanical integrity, ionic crosslinks form reducing the extent of swelling. The effect of sulfonation of PBI on crosslinking in these blends was gauged through comparison with nonsulfonated analogs. Sulfonic acid groups present in SuPBI compensate for acid groups involved in crosslinking, thereby increasing IEC and proton conductivity of the membrane. When water uptake and proton conductivity were compared to the IEC of blends containing either sulfonated or nonsulfonated PBI, no noticeable distinction between PBI types could be made. Comparisons were also made between these blends and pure SPEEK membranes of similar IEC. Blend membranes exhibit slightly lower maximum proton conductivity than pure SPEEK membranes (60 vs. 75 mS cm^?1) but had significantly enhanced dimensional stability upon immersion in water, especially at elevated temperature (80 °C). Elevated temperature measurements in humid environments show increased proton conductivity of the SuPBI membranes when compared with SPEEK‐only membranes of similar IEC (c.f. 55 for the blend vs. 42 mS cm^?1 for SPEEK at 80 °C, 90% relative humidity). © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3640–3650, 2010     

Synthesis of poly(vinyl acetate)‐b‐polystyrene and poly(vinyl alcohol)‐b‐polystyrene copolymers by cobalt‐mediated radical polymerization

Well‐defined poly(vinyl acetate) macroinitiators, with the chains thus end‐capped by a cobalt complex, were synthesized by cobalt‐mediated radical polymerization and used to initiate styrene polymerization at 30 °C. Although the polymerization of the second block was not controlled, poly(vinyl acetate)‐b‐polystyrene copolymers were successfully prepared and converted into amphiphilic poly(vinyl alcohol)‐b‐polystyrene copolymers by the methanolysis of the ester functions of the poly(vinyl acetate) block. These poly(vinyl alcohol)‐b‐polystyrene copolymers self‐associated in water with the formation of nanocups, at least when the poly(vinyl alcohol) content was low enough. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 81–89, 2007     

Star polystyrene‐b‐hyperbranched polyglycidol: Synthesis and ionic conductivity

In this work, novel star‐hyperbranched block copolymers containing four polystyrene arms and hyperbranched polyglycidol at the end of each arm (sPS‐b‐HPG) have been synthesized. The polystyrene arms were prepared through atom transfer radical polymerization of styrene starting from a four‐arm initiator. The hydroxyl‐terminated PS star polymers served as precursors for the cationic ring‐opening polymerization of glycidol using BF₃·OEt₂ as the catalyst. The chemical structures of these block copolymers were characterized by using ¹H and ¹³C NMR. DSC analysis indicated that the star‐hyperbranched block copolymers exhibited two distinct glass transition temperatures corresponding to the linear PS and the HPG segments, respectively. The addition of LiClO₄ increased the T_g of HPG segments at low concentrations, however, decreased the T_g at high concentrations. The T_g of PS segments was not affected by the addition of salts at all. Furthermore, the interaction of sPS‐b‐HPG with LiBr was studied by using viscosity analysis based on the Jones–Dole equation. The star‐like PS core strengthened the interaction of sPS‐b‐HPG with Li ions that could facile the inhomogeneous distribution of Li cations and anions in different phases, which is important in polymeric electrolytes for lithium chemical power sources. The ionic conductivity of one sPS‐b‐HPG/LiClO₄ electrolyte was measured to be higher than that of HPG/LiClO₄ electrolyte. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 949–958, 2009