首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 46 毫秒
1.
吸附相反应技术制备TiO2的结晶过程以及光降解气相甲苯   总被引:1,自引:0,他引:1  
研究了吸附相反应技术制备纳米TiO2的结晶过程, 并探讨了该过程对TiO2光催化活性的影响. 利用XRD测定了不同温度和时间焙烧后TiO2的晶型以及晶粒粒径的变化, 发现即使焙烧温度高达900 ℃, TiO2仍维持纯锐钛矿晶型. 随着焙烧温度的增加, TiO2的晶粒粒径变化不大, 均在7 nm以下, 在焙烧温度高于700 ℃时, 锐钛矿结晶峰的峰面积随温度增加, 峰面积保持不变. 改变焙烧时间基本不影响TiO2的晶型和晶粒粒径, 因而其光催化活性变化也较小. 光降解气相甲苯实验表明, 700 ℃焙烧后样品的催化活性最高, 且优于商用P25光催化剂.  相似文献   

2.
以钛酸丁酯和季铵盐改性有机蒙脱石为原料,采用原位水解法和原位脱羟法制备了TiO2/蒙脱石纳米复合物。采用X射线衍射(XRD)、拉曼光谱(Raman)表征了不同焙烧温度下TiO2/蒙脱石纳米复合物中TiO2的结构相变,并与不同焙烧温度下纯TiO2的结构相变进行对比。结果发现TiO2/蒙脱石纳米复合物中TiO2从锐钛矿相开始转变为金红石的最低温度要比纯TiO2从锐钛矿开始相转变为金红石的最低温度高200℃,且在焙烧温度1 200℃时还存在锐钛矿相,而纯TiO2在焙烧温度800℃时就全部转换为金红石相。TiO2/蒙脱石纳米复合物中TiO2和纯TiO2的平均晶粒度都随焙烧温度升高而增大,但TiO2/蒙脱石纳米复合物中TiO2的平均晶粒度要小于相同温度下焙烧纯TiO2的平均晶粒度。表明蒙脱石结构层的硅氧结构抑制了TiO2晶型由锐钛矿相向金红石相的转变,进而使相变温度升高,同时阻碍了晶体的生长。  相似文献   

3.
  摘要:以Ti(SO4)2·4H2O和尿素为原料,以聚乙二醇-1000为空间构 造剂,制备了不同粒径的具有高热稳定性的锐钛矿型纳米TiO2粉体,并 用XRD,BET和EXAFS技术对其晶相、粒径大小、比表面积及中心Ti原子 的K-边精细结构进行了表征,对其光催化降解苯酚反应的活性进行了 考察.结果表明,未经任何热处理的TiO2粉体即为锐钛矿型晶相,控制 焙烧温度可以达到控制其粒径及比表面积的目的.经850℃焙烧5h的样 品仍保持锐钛矿型晶相,未出现向金红石型晶相转变的迹象.随着纳米 TiO2晶粒的增大,Ti原子局域结构的有序度增强,边前结构A1,A2和A 3三个特征峰的强度增强,各壳层的配位数均呈增大的趋势.粒径处于 15~20nm的锐钛矿型TiO2粉体对光催化降解苯酚表现出较高的活性.  相似文献   

4.
锐钛矿型纳米TiO2介孔粉体表面织构的研究   总被引:13,自引:0,他引:13  
以硫酸钛和尿素为原料,聚乙二醇-1000为空间构造剂,104℃下经尿素水解均匀沉淀法研制颗粒分散均匀、粒径可控的高热稳定性锐钛矿型纳米TiO2介孔粉体,并对其晶相、颗粒大小、比表面积、形貌和孔道结构进行了表征.结果表明,未经任何热处理的TiO2粉体即为锐钛型晶相,颗粒为均匀分散的类球型颗粒,且颗粒间形成直通型的介孔孔道,其孔径在10~30nm之间.控制焙烧温度可以达到控制颗粒大小及形貌的目的,经850℃焙烧5h的样品仍保持锐钛矿型晶相,未出现向金红石型晶相转变的迹象.  相似文献   

5.
TiO2具有很高的光催化活性,同时TiO2纳米粒子具有耐酸碱和耐光化学腐蚀、低成本、无毒等性质,在许多领域引起广泛关注.据报道,TiO2的锐钛矿晶型比金红石晶型具有更好的光催化活性.由于金红石是TiO2的热力学稳定相,而锐钛矿是亚稳相,通常锐钛矿相在550-800℃温度范围内形成金红石相,从而降低其催化活性,限制了其应用.  相似文献   

6.
热处理对TiO2纳米管结构相变的影响   总被引:12,自引:0,他引:12  
TiO2纳米管为无定形结构,焙烧后则由无定形转变为锐钛矿型,纳米管的管状结构被破坏,晶型转变是TiO2纳米管的管状结构破坏的根本原因.经热处理,原来的TiO2纳米管部分转变为长棒状的金红石型晶柱结构,而原料TiO2在较大温度范围内焙烧均未出现长棒状晶柱结构;TiO2由A→R的相变温差很大,TiO2纳米管的A→R相变温度比原料约低350℃;合成的TiO2纳米管的比表面积和孔体积很大.  相似文献   

7.
朱建  杨俊  陈麟  曹勇  戴维林  范康年 《催化学报》2006,27(2):171-177
 以TiCl4 为钛源,采用低温苯甲醇醇解法制备了不同粒径及晶相组成的大表面TiO2纳米晶,利用X射线衍射、热重-差热分析、透射电子显微镜、拉曼光谱、紫外-可见漫反射光谱和N2物理吸附等方法考察了焙烧温度和焙烧时间对其晶相组成、晶粒尺寸、比表面积及孔体积等微结构性质的影响,并以苯酚的光催化降解为模型反应评价了样品的光催化活性. 结果表明,未经任何热处理的TiO2样品即为锐钛矿晶相,控制焙烧温度及焙烧时间可进一步调控样品的粒径、比表面积、晶相结构及表面氧缺位浓度. 经400 ℃焙烧3 h制备的纳米晶TiO2具有最佳的光催化活性,其活性比商用Degussa P-25 TiO2更高.  相似文献   

8.
高度分散的Pt/TiO2的制备及光催化活性   总被引:9,自引:2,他引:7  
张青红  高濂 《化学学报》2005,63(1):65-70,F008
用柠檬酸作为空穴捕获剂和分散剂,在温和条件下用光催化还原法将3nm金属铂沉积在7nm的锐钛矿相及介孔二氧化钛纳米晶表面,TEM观察显示铂的负载量为w=1.0%时,多数二氧化钛纳米晶表面沉积了岛状的铂团簇,XPS和电子衍射结果表明铂以游离态存在.负载w=1.0%~2.0%铂的TiO2在苯酚光氧化反应中活性显著提高,Pt/TiO2在氨气中经550℃氮化,可制得氮掺杂的Pt/TiO2可见光光催化剂,氮化过程中铂团簇没有烧结和显著长大。  相似文献   

9.
由高能面 TiO2纳米片 (TiO2-NSs) 组装成的 TiO2空心纳米盒 (TiO2-HNBs)显示出比单独 TiO2-NSs 更强的光催化性能, 但是 TiO2-HNBs 依然属于紫外光催化剂, 无法充分利用太阳能. 因此, 开发具有可见光响应的由高能面 TiO2-NSs 组装而成的 TiO2-HNBs 具有重要意义. 本文将立方体 TiOF2与含有 N 和 S 元素的生物分子蛋氨酸混合, 通过一步焙烧制备了具有可见光响应活性的 N 和 S 元素共掺杂的 TiO2-HNBs(掺杂催化剂标记为 TMx, 未掺杂催化剂标记为 Tx, x 代表焙烧温度).由立方体 TiOF2到锐钛矿相 TiO2空心纳米盒的转变是一个自模板转化过程. 氟离子的存在降低了 TiO2高能面(001)面的表面能, 从而使得高能面 TiO2纳米片的形成变得可能. 因此, 热处理立方体 TiOF2可得到由高能面 TiO2纳米片组装的 TiO2空心纳米盒.本文系统研究了焙烧温度 (300-500 ℃) 对所制 TiO2-HNBs 结构与光催化性能的影响. 结果发现, 在 350 ℃下焙烧, TiOF2完全转化成锐钛矿相 TiO2-HNBs. 但是焙烧蛋氨酸与 TiOF2的混合物, 需 400 ℃才能完全实现 TiOF2到锐钛矿相TiO2-HNBs 的转变. 这说明蛋氨酸的加入阻碍了 TiOF2向锐钛矿相 TiO2-HNBs 的转变. XPS 结果显示, 经过 400 ℃焙烧的蛋氨酸改性样品 (TM400), N 和 S 元素成功掺入了 TiO2-HNBs 晶格, 使其产生可见光催化活性.相对于 400 ℃焙烧 TiOF2所得样品 T400, 蛋氨酸改性的 TM400 催化剂可见光降解罗丹明 B 染料 (RhB) 和 NO 氧化的性能分别提升了 1.55 倍和 2.0 倍, 这与其更强的可见光吸收性能和光生载流子分离效率有关. 400 ℃焙烧的蛋氨酸改性的 TM400 可见光催化活性稳定, 连续 5 次可见光催化 RhB 降解后, 其活性没有明显改变, 显示了潜在的应用前景.  相似文献   

10.
均相水解法制备金红石含量可控的纳米TiO2   总被引:6,自引:0,他引:6  
刘威  陈爱平  林嘉平  戴智明  邱炜  刘伟  朱孟钦  臼田昭司 《化学学报》2004,62(12):1148-1152,MJ04
用均相水解法通过调节对甲苯磺酸的添加量制备了金红石含量线性可控的纳米TiO2粒子,相同条件下,没有加入对甲苯磺酸时,制备的TiO02颗粒为纯锐钛矿晶型.制备的纳米TiO2颗粒,其单晶尺寸为19.5mm(金红石),13.5mm(锐钛矿),比表面积72.7m^2/g,通过公式计算得到了制备的TiO2纳米颗粒带隙能为2.83eV,比P25和纯锐钛矿纳米TiO2颗粒的带隙能均低.  相似文献   

11.
In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.  相似文献   

12.
KMnO4-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.  相似文献   

13.
The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.  相似文献   

14.
Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.  相似文献   

15.
A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.  相似文献   

16.
The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp3)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp2)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp2)?H and aliphatic 1,5- and 1,6-C(sp3)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp3)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp2)?H insertion.  相似文献   

17.
The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.  相似文献   

18.
An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.  相似文献   

19.
20.
N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号