Quartz Crystal Microbalance for Selenite Sensing Based on Growth of Cadmium Selenite Crystals Immobilized on a Monolayer of Phosphorylated 11-Mercapto-1-Undecanol

 A quartz crystal microbalance (QCM) sensor for selenite ions in aqueous solution was constructed based on crystal formation of cadmium selenite, immobilized with a self-assembly monolayer (SAM) of phosphorylated 11-mercapto-1-undecanol (MUD) on a QCM gold electrode surface. The mass change caused by the selective adsorption of selenite ions on the cadmium selenite crystals at the solid/solution interface was detected by the QCM. The response (−ΔF) of the modified QCM oscillator increased with increasing selenite ion concentrations in sample solutions, ranging from 9.7×10⁻⁵ to 9.0×10⁻⁴ M at pH 7.4. The synthetic process of anchoring cadmium selenite crystals on the phosphorylated MUD organic film was also followed by using X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). The atomic concentrations measured by XPS confirmed the crystal growth of cadmium selenite on the phosphorylated MUD SAM at the QCM gold electrode surface. From the AFM images, changes in surface topographic features were followed: the MUD SAM and phosphorylated MUD on the QCM gold electrode had similar surface roughness; however the difference for the cadmium selenite film on the phosphorylated MUD SAM was clearly seen. The observed QCM frequency change of the modified QCM oscillator per unit time was found to be proportional to the square of the supersaturation of cadmium selenite, indicating the crystal growth of cadmium selenite at the solid/solution interface. The modified QCM oscillator exhibited selectively strong QCM response to SeO₃ ²⁻ ion. In contrast, the responses to tested interfering anions were almost negligible. The order of anion selectivities of the present modified QCM sensor was SeO₃ ²⁻≫CO₃ ²⁻>SeO²⁻ ₄, SO₄ ²⁻, Br⁻, I⁻, NO₃ ⁻. These selectivities were basically attributable to the differences in solubility products and solubilities for the salts of each anion with cadmium (II) ion. Received May 12, 1998. Revision December 29, 1998.     

Scavenging of reactive oxygen radicals by resveratrol: antioxidant effect

Pulse radiolysis of resveratrol was carried out in aqueous solutions at pH ranging from 6.5 to 10.5. The one-electron oxidized species formed by the N^•₃ radicals at pH 6.5 and 10.5 were essentially the same with λ_max at 420 nm and rate constant varying marginally (k = (5−6.5) × 10⁹ dm³ mol⁻¹ s⁻¹). The nature of the transients formed by NO^•₂, NO^• radical reaction at pH 10.5 was the same as that with N^•₃, due to the similarity in decay rates and the absorption maximum. Reaction of ^•OH radical with resveratrol at pH 7 gives an absorption maximum at 380 nm, attributed to the formation of carbon centered radical. The repair rates for the thymidine and guanosine radicals by resveratrol were approx. 1 × 10⁹ dm³ mol⁻¹ s⁻¹, while the repair rate for tryptophan was lower by nearly an order of magnitude (k = 2 × 10⁸ dm³ mol⁻¹ s⁻¹). The superoxide radical anion was scavenged by resveratrol, as well as by the Cu–resveratrol complex with k = 2 × 10⁷ and 1.5 × 10⁹ dm³ mol⁻¹ s⁻¹, respectively. Its reduction potential was also measured by cyclic voltammetry.     

Platinum electrode coated with a bentonite–carbon composite as an environmental sensor for detection of lead

A Pt wire coated with a bentonite–carbon composite in a poly(vinyl chloride) membrane was used for detection of lead. The sensor has a Nernstian slope of 29.42±0.50 mV per decade over a wide range of concentration, 1.0×10⁻⁷ to 1.0×10⁻³ mol L⁻¹ Pb(NO₃)₂. The detection limit is 5.0×10⁻⁸ mol L⁻¹ Pb(NO₃)₂ and the electrode is applicable in the pH range 3.0–6.7. It has a response time of approximately 10 s and can be used at least for three months. The electrode has good selectivity relative to nineteen other metal ions. The practical analytical utility of the electrode is demonstrated by measurement of Pb(II) in industrial waste and river water samples.     

Thiocyanate-selective electrode based on N-salicylidene-benzylamineato copper(II) complex

Highly selective poly(vinyl chloride) (PVC) membrane electrode based on N-salicylidene-benzylamineato copper(II) complexes [Cu(SBA)₂] as new carriers towards thiocyanate-selective electrode was reported. The influence of membrane composition, pH and possible interfering anions were investigated on the response properties of the electrode. The resulting electrode exhibits anti-Hofmeister selectivity sequence: SCN⁻ > ClO₄⁻ > Sal⁻ > I⁻ > Br⁻ > NO₃⁻ > NO₂⁻ > SO₃²⁻ > H₂PO₄⁻ > Cl⁻ > SO₄²⁻, and a near-Nernstian potential linear range for thiocyanate from 1.0 × 10⁻¹ to 9.0 × 10⁻⁷ M with a detection limit of 7.0 10⁻⁷ M and a slope of , over a wide pH range of 3.0–9.0 in phosphate buffer solution at 20°C. The proposed electrode has a fast response time of about 5–10 s and can be used for at least 3 months without any considerable divergence in potential. The electrode was successfully applied to the determination of thiocyanate in waste water and human urine and saliva samples. Published in Russian in Elektrokhimiya, 2008, Vol. 44, No. 3, pp. 293–299. The text was submitted by the authors in English.     

Aluminium(III)-selective electrode based on a newly synthesized glyoxal-<Emphasis Type="Italic">bis</Emphasis>-thiosemicarbazone Schiff base

A PVC membrane electrode for Al³⁺ based on glyoxal-bis-thiosemicarbazone (GBTC) as an ion carrier was developed. The electrode exhibits a Nernstian slope of 20.1 mV per decade and a linear range of 1.8 × 10⁻⁵−1.0 × 10⁻¹ M for Al(NO₃)₃ with a detection limit of 8.7 × 10⁻⁶ M. It has a fast response time of about 10 s and can be used for at least 1 month. The proposed membrane sensor revealed a good selectivity for Al³⁺ over a wide variety of other metal ions and could be used in the pH range of 2.5–4.5. The text was submitted by the authors in English.     

ESR study of lithium nitrate irradiated with gamma-rays with total doses from 10 to 100 Mrad

Natural non-pretreated polycrystalline lithium nitrate was irradiated by gamma-rays of⁶⁰Co with total radiation doses from 10 to 100 Mrad, at room temperature. No color centers were observed in samples irradiated in this range. X-ray and infrared studies evidenced the distortion of the lattice planes. In general, the following species were detected NO₂, NO₃ radicals, and NO₂ ²⁻, NO₃ ²⁻, O₂ ⁻ ionic radicals.     

Chemical compositions of precipitation and scavenging of particles in Beijing

Wet deposition is the scavenging approach of pollutants from the atmosphere. Rain in summer and snow in winter are the main scavenging processes of air pollutants by wet deposition in Beijing and key factors of changing air pollutants concentrations[1]. T…     

Application of co-electroosmotic capillary electrophoresis for the determination of inorganic anions and carboxylic acids in soil and plant extract with direct UV detection

Summary Indirect UV detection in capillary zone electrophoresis (CZE) is frequently used for the determination of inorganic anions and carboxylic acids. However, there are few reports on direct UV detection of these solutes in real samples. This paper describes the use of direct UV detection of inorganic anions and organic acids in environmental samples using co-electroosmotic capillary zone electrophoresis (co-CZE) at 185 nm. The best separation and detection of the solutes was achieved using a fused silica capillary with an electrolyte containing 25 mM phosphate, 0.5 mM tetradecyltrimethylammonium bromide (TTAB) and 15% acetonitrile (v/v) at pH 6.0. Four common inorganic anions (Cl⁻, NO₂ ⁻, NO₃ ⁻ and SO₄ ²⁻) and 11 organic acids (oxalic, formic, fumaric, tartaric, malonic, malic, citric, succinic, maleic, acetic, and lactic acid), were determined simultaneously in 15 min. Linear calibration plots for the test solutes were obtained in the range 0.02–0.5 mM with detection limits ranging from 1–9 μM depending on the analyte. The proposed method was successfully used to determine inorganic anions and carboxylic acids in soil and plant tissue extracts with direct injection of the sample.     

Fine competition and control among argentophilic,electrostatic, and π···π interactions in a molecular chair structure

The reaction of AgX (X⁻ = NO₃ ⁻, ClO₄ ⁻, or CF₃SO₃ ⁻) with 1,3-bis(3-pyridyl)tetramethyldisiloxane (L) at room temperature affords 20-membered metallacyclodimers, [Ag(L)]₂(X)₂. For the macrocyclodimer, fine competition among argentophilic, electrostatic, and π···π interaction exists. The macrocyclodimer is a unique molecular chair that tunes a transannular argentophilic interaction via the bite size of the counteranions. In order to reversibly control the argentophilic interaction, anion exchange has been accomplished. The anion exchangeability depends on the water solubility rather than the electrostatic interaction between silver(I) and anions.     

Formation of active species in spark discharge and their possible use

The chemical effects of self-sustained spark discharge with an energy per pulse of 5.9 × 10⁻² J, a pulse repetition frequency of 10 Hz, and a spark-gap breakdown voltage of 6 kV have been studied. The discharge generated a UV photon flux of (2.5 ± 0.3) × 10¹⁵ cm⁻² s⁻¹ with an energy density of (2 ± 0.3) × 10⁻³ J cm⁻¹ s⁻¹ and the emission spectrum maximum at 220 nm. The action of the discharge on water samples leads to a decrease in pH and to buildup of oxidizing and reducing species. The formation of HO₂^· radicals with an initial yield of (1.2 ± 0.3) × 10⁻⁶ mol L⁻¹ s⁻¹ has been detected in the liquid. The initial yields of acid residues (increment in [H⁺]), oxidants, and reducing agents are (5.8 ± 1.6) × 10⁻⁷, (3.3 ± 1) × 10⁻⁶, and (4.2 ± 1) × 10⁻⁷ mol equiv L⁻¹s⁻¹, respectively. The formation of NO₃⁻ and NO₄⁺ ions, nitrosamines, and organic compounds has been established.     

Aggregation and sedimentation stability of microcrystalline cellulose suspensions in aqueous aluminum nitrate solutions

The aggregation and sedimentation stability of dilute suspensions of microcrystalline cellulose in aqueous solutions of Al(NO₃)₃(2 × 10⁻⁵–2 × 10⁻³ mol/l) is studied by the photometric method at pH 2–11. It is found that, in the absence of Al(NO₃)₃, microcrystalline cellulose suspensions are stable with respect to aggregation throughout the pH range in question. The addition of Al(NO₃)₃ induces the coagulation and accelerates the sedimentation of microcrystalline cellulose aggregates. At all concentrations of Al(NO₃)₃, the maximum loss in stability is observed at pH 7–9. Original Russian Text ? P.M. Mosur, A.V. Lorentsson, Yu.M. Chernoberezhskii, 2009, published in Kolloidnyi Zhurnal, 2009, Vol. 71, No. 4, pp. 566–568.     

Formations of Active Species and By-Products in Water by Pulsed High-Voltage Discharge

Formations of active species and by-products are different from bubbling different gases in a pulsed high-voltage discharge reactor. The identification of all the products and the formation rate determination of active species are quite important as the process is applied to wastewater disposal. Serials of measurements were conducted to do the identifications and determinations in this paper. Amounts of · OH all increased but that of H₂O₂ all decreased by bubbling gas. The · OH formation rate was 3.49 × 10⁻⁷, 3.56 × 10⁻⁷, 3.21 × 10⁻⁷ and 1.94 × 10⁻⁷ mol l⁻¹ s⁻¹ with bubbling nitrogen, argon, air and oxygen respectively, but it was 1.61 × 10⁻⁷ mol s⁻¹ l⁻¹ without bubbling. Without any bubbling, the H₂O₂ formation rate was up to 6.53 × 10⁻⁶ mol l⁻¹ s⁻¹, while it was 9.97 × 10⁻⁷, 1.663 × 10⁻⁷, 1.73 × 10⁻⁶ and 3.14 × 10⁻⁶ mol l⁻¹ s⁻¹ with bubbling nitrogen, argon, air and oxygen, respectively. NO₂⁻ and NO₃⁻ was detected in discharged water with bubbling nitrogenous gas. Their formation made the pH decreased.     

Study of mechanism retention of nonvolatile alkylphosphonic acids on unmodified selected polymer-based ion exchanger columns

The retention of alkylphosphonic acids (MPA, EPA, PPA, and BPA) and inorganic anions (Cl⁻, NO₃⁻, and SO₄²⁻) were studied on two anion exchangers, e.g., Dionex IonPac AS4A-SC (250 ± 4 mm I.D.) and Satisfaction P 4000-SAX (50 ± 4.6 mm I.D.) under isocratic elution conditions with evaporative light scattering detector. The plots of retention factors, k, of organic anions vs. the reciprocal of eluent ion concentration show good linearity. The major retention mechanisms are interpreted as ion exchange and some others interactions. The C effect of organic modifier added to the aqueous buffered mobile phase is also investigated.     

Ion chromatographic and spectrometric determination of water-soluble compounds in airborne particulates, and their correlations in an industrial area in Attica, Greece

In the time period from June 2005 to May 2006 in 42 sampling campaigns 84 filter samples of airborne particulate matter, coarse (PM_10–2.5) and fine (PM_2.5), were collected using a Gent stacked filter unit in the coastal industrial area of Aspropyrgos in Attica, Greece. The average PM₁₀ (PM_10–2.5 + PM_2.5) concentration was found to be 66 μg · m⁻³, exceeding more than 1.6 times the annual limit of 40 μg · m⁻³. The samples were analysed for Cl⁻, NO₃ ⁻, SO₄ ²⁻, Ca²⁺, Mg²⁺, Na⁺, K⁺ and NH₄ ⁺ using ion chromatography. The data were compared with results obtained with other spectrometric methods, such as inductively coupled plasma-atomic emission spectrometry, atomic absorption spectrometry, energy dispersive X-ray fluorescence and reflectometry. The determined average ionic content comprised about 44% of the PM₁₀ mass. The ionic composition, as well as the possible matrix compounds in both fractions were evaluated by dividing the sampling period into summer and winter season. In the PM_10–2.5/PM_2.5 fraction in summer time the concentrations of Ca²⁺, Mg₂₊ and NO₃ ⁻ were enriched in the coarse fraction. In winter time all species were enriched in the coarse fraction, especially Ca²⁺, Cl⁻ and NO₃ ⁻. NH₄ ⁺ was constantly higher in the fine fraction in summer as well as in winter time. Factor analysis was applied to obtain correlations between cations and anions leading to matrix compounds in both fractions. From the evaluation of the results obtained, some of the local air pollution sources could be identified. Correspondence: Klaus-Michael Ochsenkühn, Laboratory for Trace Element Studies, Institute of Physical Chemistry, NCSR “Demokritos”, Aghia Paraskevi 15310, Athens, Greece     

A theoretical investigation on structures of tripodal thiourea derivatives and their anion recognition

The structural geometries of three tripodal thiourea receptors, i.e. 1,3,5-triethyl-2,4,6-tris[(N′-methylthioureido)methyl]benzene (1), tris[N′-methyl-N-(2-aminoethyl)thiourea]methane (2), tris[N′-methyl-N-(2-aminoethyl)thiourea]amine (3), and their complexes with F⁻, Cl⁻, Br⁻, I⁻, NO₃ ⁻, CO₃ ²⁻, SO₄ ²⁻, HSO₄ ⁻, PO₄ ³⁻, HPO₄ ²⁻ and H₂PO₄ ⁻ were obtained using the density functional theory calculations. Electronic and thermodynamic properties of anion binding complexes of the receptors 1, 2 and 3 were investigated. Recognition abilities of all the receptors in terms of selectivity coefficients are reported. Intermolecular interactions in all the studied complexes occurring via multi-point hydrogen bonding were found. The receptors 1, 2 and 3 were found to be excellent selectivity for phosphate ion and their binding free energy for the phosphate ion are −292.57, −291.77 and −295.01 kcal/mol, respectively.     

Preparation of 1-butyl-3-methylimidazolium salts and study of their phase behavior and intramolecular intractions

Seven organic salts of 1-butyl-3-methylimidazolium with anions Br⁻, BF₄ ⁻, NO₃ ⁻, SO₄ ²⁻, HSO₄ ⁻, SCN⁻, PO₄³⁻ were prepared. Structure of these compounds is elucidated and purity is confirmed. The products are characterized by melting point, thin layer chromatography, data of elemental analysis, cromatomass-, NMR and IR spectroscopy. All these compounds are ionic liquids, five are low temperature ones. Principal thermal characteristics are found that allow accounting for the phase behavior of the prepared compounds at their application. Existence of intramolecular and intermolecular interactions between the heterocyclic anion and inorganic cation in by means of the formation of hydrogen bond is established.     

Capillary electrophoretic speciation of Cu(II) and Co(III) in the electroless copper plating baths

Summary A capillary electrophoretic method for the determination of Cu(II) and Co(III) chelates with ethylenediamine in electroless copper plating baths has been developed. The influence of carrier electrolyte parameters such as nature of counter-ion and pH were studied and discussed. The optimised separations were carried out in a fused silica capillary (57 cm × 75 μm I.D.) filled with an ethylenediamine sulfate electrolyte (20 mol L⁻¹ ethylendiamine, pH7.0 with H₂SO₄; applied voltage, +25 kV) using direct UV detection at 214 nm. The detection limits for a signalto-noise ratio of 3 and 10s hydrodynamic injection were 5×10⁻⁶ mol L⁻¹ for Cu(II) and 1×10⁻⁶ mol L⁻¹ for Co(III). The relative standard deviations of the peak areas for Cu(II) and Co(III) were found to be 1.5% and 2.4%, respectively, with five consecutive injections of standard solution containing 5×10⁻⁵ mol L⁻¹ of each metal ion. Application of the method to the speciation of Cu(II) and Co(III) complexes in copper plating bath samples is also demonstrated.     

Simultaneous determination of silicic acid, Ca, Mg and Al in mineral water and composite tablets by Ion chromatography

Summary A simple, selective and sensitive ion-chromatography method was investigated for simultaneously determining silicic acid, Ca²⁺, Mg²⁺, Al³⁺ and anions (Cl⁻ and NO ₃ ⁻ ) in real samples. It involved a single-column ion-chromatograph with sodium hydroxide-methanol-water eluent and conductometric detection. Cations were converted to complex anions by adding EDTA to the sample solution. A set of well-defined peaks of silicic acid, Ca²⁺, Mg²⁺, Al³⁺, Cl⁻ and NO ₃ ⁻ were obtained. Detection limits using 3.3σ (σ=standard deviation of blank solution) were 1.25×10⁻⁶ M for H₃SiO ₄ ⁻ , 1.32×10⁻⁶ M for Ca²⁺, 1.28×10⁻⁶ M for Mg²⁺, 1.33×10⁻⁶ M for Al³⁺, 1.31×10⁻⁶ M for Cl⁻ and 1.24×10⁻⁶ M for NO ₃ ⁻ . The method was successfully applied to analysis of mineral water and composite tablets.     

The extraction of Cr(III) from aqueous thiocyanate solutions and its separation from Co(II) and Ni(II)

For the system liquid anion-exchanger—Cr(III)−NCS⁻, an investigation has been made of the dependence of the percentage extraction of Cr(III) on parameters such as standing time of the Cr(III)−NCS⁻ solution, temperature, pH and type of exchanger. Quantitative extraction of e.g. 4·10⁻⁴ M Cr(III) by 0.1M Aliquat in CCl₄ is easily achieved at room temperature, using 4.75M KNCS−0.05N HCl as aqueous phase. At high Cr(III) concentrations, the complex anion present in the organic phase is Cr(NCS) ₆ ³⁻ ; when working with dilute metal ion solutions, the species extracted is Cr(NCS)₄ (H₂O) ₂ ⁻ . Separations of mixtures containing 10⁻²−10⁻⁴ M Co(II), Ni(II) and Cr(III) have successfully been accomplished.     

Electrocatalytic oxidation of nitrite at a terpyridine manganese(II) complex modified carbon past electrode

A carbon past electrode modified with [Mn(H₂O)(N₃)(NO₃)(pyterpy)], ( \textpyterpy = 4￠- ( 4 - \textpyridyl ) - 2,2￠:\text6￠,\text2￠￠- \textterpyridine ) \left( {{\text{pyterpy}} = 4\prime - \left( {4 - {\text{pyridyl}}} \right) - 2,2\prime:{\text{6}}\prime,{\text{2}}\prime\prime - {\text{terpyridine}}} \right) complex have been applied to the electrocatalytic oxidation of nitrite which reduced the overpotential by about 120 mV with obviously increasing the current response. Relative standard deviations for nitrite determination was less than 2.0%, and nitrite can be determined in the ranges of 5.00 × 10⁻⁶ to 1.55 × 10⁻² mol L⁻¹, with a detection limit of 8 × 10⁻⁷ mol L⁻¹. The treatment of the voltammetric data showed that it is a pure diffusion-controlled reaction, which involves one electron in the rate-determining step. The rate constant k′, transfer coefficient α for the catalytic reaction, and diffusion coefficient of nitrite in the solution, D, were found to be 1.4 × 10⁻², 0.56× 10⁻⁶, and 7.99 × 10⁻⁶ cm² s⁻¹, respectively. The mechanism for the interaction of nitrite with the Mn(II) complex modified carbon past electrode is proposed. This work provides a simple and easy approach to detection of nitrite ion. The modified electrode indicated reproducible behavior, anti-fouling properties, and stability during electrochemical experiments, making it particularly suitable for the analytical purposes.