Formation of platinum sites on layered double hydroxide type basic supports: II. Effect of the nature of the interlayer anion of the layered aluminum-magnesium hydroxides on platinum binding and Pt/MgAlO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> formation

The interaction of aqueous H₂PtCl₆ solutions with hydrotalcite-type aluminum-magnesium hydroxides differing in the nature of their interlayer anion is reported. In the case of CO₃²⁻ as the interlayer anion, the introduction of the platinum(IV) chloro complex does exerts no significant effect on the structural properties of the support, on its thermal decomposition dynamics, and on the textural characteristics of the resulting oxide phase. The binding of the platinum complexes to “activated hydrotalcite” with interlayer OH⁻ anions increases the interplanar spacing and enhances the thermal stability of the layered structure. This is accompanied by marked changes in textural characteristics of the material, leading to the formation of a nearly monodisperse mixed oxide phase. In the Pt/MgAlO _x samples obtained by reductive treatment, a considerable proportion of platinum is in the form of planar particles, and this corroborates the hypothesis that the metal complex at the sorption stage is mainly localized in the interlayer space of this support. Platinum binds to the support as chloro complexes via rapid anion exchange, and these bound platinum species are characterized by a higher reduction temperature.     

Sulfate intercalated layered double hydroxides prepared by the reformation effect

The removal of the sulfate anion from water using synthetic hydrotalcite (Mg/Al LDH) was investigated using powder X-ray diffraction (XRD) and thermogravimetric analysis (TG). Synthetic hydrotalcite Mg₆Al₂(OH)₁₆(CO₃)·4H₂O was prepared by the co-precipitation method from aluminum and magnesium chloride salts. The synthetic hydrotalcite was thermally activated to a maximum temperature of 380 °C. Samples of thermally activated hydrotalcite where then treated with aliquots of 1000 ppm sulfate solution. The resulting products where dried and characterized by XRD and TG. Powder XRD revealed that hydrotalcite had been successfully prepared and that the product obtained after treatment with sulfate solution also conformed well to the reference pattern of hydrotalcite. The d₍₀₀₃₎ spacing of all samples was found to be within the acceptable region for a LDH structure. TG revealed all products underwent a similar decomposition to that of hydrotalcite. It was possible to propose a reasonable mechanism for the thermal decomposition of a sulfate containing Mg/Al LDH. The similarities in the results may indicate that the reformed hydrotalcite may contain carbonate anion as well as sulfate. Further investigation is required to confirm this.     

Fabrication of layered double hydroxide spheres through urea hydrolysis and mechanisms involved in the formation

The goal of this study is to prepare hydrotalcite pellets and validate their potential utility in catalysts and catalysts support. Hydrotalcite pellets were synthesized by urea hydrolysis. Urea hydrolysis can provide both carbonate as the intercalated anion and hydroxyl anions to form Mg–Al layered double hydroxide (LDH) with carbonate intercalation. Urea hydrolysis was also used to generate NH₃ which plays a critical role in the process of synthesis hydrotalcite pellets. Mechanism of the formation hydrotalcite pellets was also discussed. The as-prepared samples were well characterized by X-ray diffraction, scanning electron microscopy, transmission electronic microscope, N₂ adsorption/desorption, and Fourier transform infrared spectroscopy, respectively. The results revealed that the hydrotalcite pellets were well-crystallized and formed by self-assembly of hexagonal platelets LDHs. The present work suggests that it is possible to grow hydrotalcite pellets directly through one-step aqueous solution-phase chemical route under controlled conditions.     

Reactivity of Mg–Al hydrotalcites in solid and delaminated forms in ammonium carbonate solutions

Treatment of Mg–Al hydrotalcites (LDHs, layered double hydroxides) in aqueous (NH₄)₂CO₃ at 298 K leads to composites of dawsonite, hydrotalcite, and magnesium ammonium carbonate. The mechanism and kinetics of this transformation, ultimately determining the relative amounts of these components in the composite, depend on the treatment time (from 1 h to 9 days), the Mg/Al ratio in the hydrotalcite (2-4), and on the starting layered double hydroxide (solid or delaminated form). The materials at various stages of the treatment were characterized by inductive coupled plasma-optical emission spectroscopy, X-ray diffraction, transmission electron microscopy, infrared spectroscopy, thermogravimetry, and nitrogen adsorption at 77 K. The progressive transformation of hydrotalcite towards crystalline dawsonite and magnesium ammonium carbonate phases follows a dissolution–precipitation mechanism. A gradual decrease of the Mg/Al ratio in the resulting solids was observed in time due to magnesium leaching in the reacting medium. Dawsonite–hydrotalcite composite formation is favored at high aluminum contents in the starting hydrotalcite, while the formation of magnesium ammonium carbonate is favored at high Mg/Al ratios. The synthetic strategy comprising hydrotalcite delamination in formamide prior to aqueous (NH₄)₂CO₃ treatment is more reactive towards composite formation than starting from the bulk solid hydrotalcite.     

Thermogravimetric analysis of layered double hydroxides with chloramphenicol and salicylate in the interlayer space

The thermal behavior of the new inorganic-organic nanohybrid materials obtained by intercalation of chloramphenicol and salicylate into layered double hydroxides (LDHs) by direct synthesis method, anion exchange reaction and the reconstruction method was evaluated by dynamic thermogravimetric analysis in air, at heating rates of 5°C min⁻¹. The XRD patterns of the samples are characteristic for those of well crystallized solids with layered double hydroxide structures. The FTIR spectroscopy results show the presence of the organic compound within the network structure of the synthesized LDHs. The kinetic parameters (reaction order (n) apparent activation energy (E _a) and pre-exponential factor (lnA) were calculated by the Coats-Redfern method. The compensation effects were determined.     

Synthesis and characterization of layered double hydroxides with different cations (Mg,Co, Ni,Al), decomposition and reformation of mixed metal oxides to layered structures

Three layered double hydroxides (LDH) [Mg_1−xAl_x(OH)₂]^x+(A^m−)_x/m]·nH₂O and [M^II _1−xM^III _x (OH)₂]^x+(A^m−)_x/m]·nH₂O (M^II — Mg, Co, Ni; MIII — Al; A — CO₃ ²⁻) were successfully synthesized by the low supersaturation method. The as-synthesized LDH samples were thermally decomposed and the derived mixed metal oxides reformed back to layered structures in water and magnesium nitrate media at different temperatures. All synthesized samples were characterized by X-ray diffraction (XRD) analysis, thermogravimetric (TG) analysis, X-ray fluorescence (XRF) analysis and scanning electron microscopy (SEM). The results of XRD and XRF analyses showed that single-phase layered double hydroxides were formed during synthesis and reformation. It was demonstrated, that a partially substituted by cobalt and nickel LDH samples also show memory effect. The crystallite size of regenerated LDH depends on the regeneration media, temperature and chemical composition. The LDH samples after regeneration consist of large particles with sharp edges along with a large amount of smaller particles     

Thermal analysis of hydrotalcite synthesised from aluminate solutions

The aluminate hydrotalcites are proposed to have either of the following formulas: Mg₄Al₂(OH)₁₂(CO₃ ²⁻)·xH₂O or Mg₄Al₂(OH)₁₂(CO₃ ²⁻, SO₄ ²⁻)·xH₂O. A pure hydrotalcite phase forms when magnesium chloride and aluminate solutions are mixed at a 1:1 volumetric ratio at pH 14. The synthesis of the aluminate hydrotalcites using seawater results in the formation of an impurity phase bayerite. Two decomposition steps have been identified for the aluminate hydrotalcites: (1) removal of interlayer water (230 °C) and (2) simultaneous dehydroxylation and decarbonation (330 °C). The dehydration of bayerite was observed at 250 °C. X-ray diffraction techniques determined that the synthesis of aluminate hydrotalcite with seawater and a volumetric ratio of 4.5 results in very disordered structures. This was shown by a reduction in the mass loss associated with the removal of interlayer water due to the reduction of interlayer sites caused by the misalignment of the metal-hydroxyl layers.     

Mechanistic study of the oxidation of N-phenyldiethanolamine by <Emphasis Type="Italic">bis</Emphasis>(hydrogen periodato)argentate(III) complex anion

The kinetics of oxidation of phenyldiethanolamine (PEA) by a silver(III) complex anion, [Ag(HIO₆)₂]⁵⁻, has been studied in an aqueous alkaline medium by conventional spectrophotometry. The main oxidation product of PEA has been identified as formaldehyde. In the temperature range 20.0–40.0 °C , through analyzing influences of [OH⁻] and [IO ₄ ⁻ ]_tot on the reaction, it is pseudo-first-order in Ag(III) disappearance with a rate expression: k _obsd = (k ₁ + k ₂[OH⁻]) K ₁ K ₂[PEA]/{f([OH⁻])[IO ₄ ⁻ ]_tot + K ₁ + K ₁ K ₂ [PEA]}, where k ₁ = (0.61 ± 0.02) × 10⁻² s⁻¹, k₂ = (0.049 ± 0.002) M⁻¹ s⁻¹ at 25.0 °C and ionic strength of 0.30 M. Activation parameters associated with k ₁ and k ₂ have also been derived. A reaction mechanism is proposed involving two pre-equilibria, leading to formation of an Ag(III)-periodato-PEA ternary complex. The ternary complex undergoes a two-electron transfer from the coordination PEA to the metal center via two parallel pathways: one pathway is spontaneous and the other is assisted by a hydroxide ion.     

Intercalation of hydrotalcites with hexacyanoferrate(II) and (III)—a thermoRaman spectroscopic study

Raman spectroscopy using a hot stage indicates that the intercalation of hexacyanoferrate(II) and (III) in the interlayer space of a Mg, Al hydrotalcites leads to layered solids where the intercalated species is both hexacyanoferrate(II) and (III). Raman spectroscopy shows that depending on the oxidation state of the initial hexacyanoferrate partial oxidation and reduction takes place upon intercalation. For the hexacyanoferrate(III) some partial reduction occurs during synthesis. The symmetry of the hexacyanoferrate decreases from O_h existing for the free anions to D_3d in the hexacyanoferrate interlayered hydrotalcite complexes. Hot stage Raman spectroscopy reveals the oxidation of the hexacyanoferrate(II) to hexacyanoferrate(III) in the hydrotalcite interlayer with the removal of the cyanide anions above 250 °C. Thermal treatment causes the loss of CN ions through the observation of a band at 2080 cm⁻¹. The hexacyanoferrate (III) interlayered Mg, Al hydrotalcites decomposes above 150 °C.     

Synthesis of layered zinc hydroxide chlorides in the presence of Al(III)

Zinc hydroxide chloride particles were synthesized by hydrolysis of ZnCl₂ solutions dissolving AlCl₃ at different atomic Al/Zn ratios from 0 to 1.0 and characterized by various techniques. Increasing Al/Zn ratio changed the crystal phases of the products as ZnO→ZnO+ZHC (Zn₅(OH)₈Cl₂·H₂O)→ZHC→LDH (layered double hydroxides, Zn-Al-Cl) and the particle morphology as agglomerates (ZnO)→fine particles (ZnO)→plates (ZHC)+rods (ZnO)→plates (ZHC)→plates (LDH). The atomic Cl/Zn ratios of LDH particles formed at Al/Zn?0.3 were ca. 0.3 despite the increase of Al/Zn ratio, being due to the intercalation of CO₃²⁻ into the LDH crystal. The OH⁻ content of LDH estimated by TG was reduced by the deprotonation of OH⁻ to counteract the excess positive charge produced by replacing Zn(II) with Al(III). ZHC exhibited a high adsorption selectivity of H₂O.     

Preparation of Mg–Al layered double hydroxides intercalated with alkyl sulfates and investigation of their capacity to take up N,N-dimethylaniline from aqueous solutions

This study examined the effect of the interlayer spacing of a Mg–Al layered double hydroxide (Mg–Al LDH) on the ability of the Mg–Al LDH to take up a nonionic organic material. Mg–Al LDHs, intercalated with 1-propanesulfonate (PS^?), 1-hexanesulfonate (HS^?), and 1-dodecanesulfonate (DS^?), were prepared by coprecipitation, yielding PS·Mg–Al LDH, HS·Mg–Al LDH, and DS·Mg–Al LDH, respectively. The increase in the alkyl chain lengths of the Mg–Al LDHs (PS^? < HS^? < DS^?) resulted in the perpendicular orientation of the organic acid anions in the interlayer of Mg–Al LDH, which in turn resulted in more organic acid anions being accommodated in the interlayer space. An organic acid anion with a large molecular length was more easily intercalated in the interlayer of Mg–Al LDH than one with a small molecular length. This was attributed to the hydrophobic interaction between the alkyl chains, affecting the intercalation of the organic acid anions. The uptake of N,N-dimethylaniline (DMA) by Mg–Al LDHs increased in the order PS·Mg–Al LDH < HS·Mg–Al LDH < DS·Mg–Al LDH. The uptake was attributed to the hydrophobic interactions between DMA and the intercalated PS^?, HS^?, and DS^?. Thus, Mg–Al LDH, which has a lot of large interlayer spacings when intercalated with organic acid anions, can take up a large number of DMA molecules from an aqueous solution.     

Na-dodecylsulfate modification of hydrocalumite and subsequent effect on the structure and thermal decomposition

Hydrocalumite (CaAl-Cl-LDH) has the similar structure to layered double hydroxide (LDH). The effects of Na-dodecylsulfate (SDS) on the structure, morphology, and thermal property of CaAl-Cl-LDH have been investigated. Through ion exchange, CaAl-Cl-LDH had been modified with SDS at two concentrations: 0.005 mol L⁻¹ and 0.2 mol L⁻¹. Two different adsorption behaviors were observed through Fourier transform infrared (FTIR) spectra and X-ray diffraction (XRD) patterns. When the SDS concentration was 0.005 mol L⁻¹, surface anion exchange was the major process. When the SDS concentration was 0.2 mol L⁻¹, anion exchange intercalation occurs, with the interlayer distance expanded to 3.25 nm, and the particle morphology from regular hexagons to irregular platelets. The thermal analysis (TG–DTA) showed that dehydration and dehydroxylation occur at a lower temperature when hydrocalumite was intercalated with dodecylsulfate. All these observations revealed that the property of CaAl-Cl-LDH has been changed by SDS modification.     

Solution decomposition of the layered double hydroxide (LDH) of Zn with Al

The layered double hydroxides (LDH) of Zn with Al containing intercalated CO₃²⁻ and NO₃⁻ ions undergo solution decomposition to yield a highly crystalline oxide mixture comprising ZnO and ZnAl₂O₄ at temperatures as low as 150–180 °C under hydrothermal conditions. In contrast solid-state decomposition takes place at a much higher temperature (240–315 °C) in air. Solution decomposition is not only guided by the low octahedral crystal field stabilization energy of Zn²⁺ ions, a factor that also affects solid-state decomposition, but also by solubility considerations. The LDHs of Mg and Ni with Al do not undergo solution decomposition.     

Synthesis and characterization of layered double hydroxides (LDH) intercalated with non-steroidal anti-inflammatory drugs (NSAID)

Layered double hydroxides (LDHs) with the hydrotalcite type structure and a Mg:Al ratio of two have been prepared, with salicylate or naproxen in the interlayer. Two synthetic routes have been used: reconstruction from a mildly calcined hydrotalcite-CO₃ precursor, and a coprecipitation method with chlorides of the metals. The solids have been characterized using several physicochemical techniques, i.e., powder X-ray diffraction, FTIR and ¹³C CP/MAS NMR spectroscopies and thermal analysis (thermogravimetric and differential thermal analyses). The gallery height determined is in all cases larger than the size of the drug, 11.5 Å for salicylate and 15.8 and 16.6 Å for naproxen, depending on the specific synthesis route followed. Experimental data suggest the anion molecules form a tilted bilayer, with the carboxylate groups pointing towards the brucite-like layers. The solids are stable up to 230 °C and their evolution from 350 °C upwards is very similar to that observed for a carbonate-containing hydrotalcite, forming mostly amorphous solids with a large specific surface area.     

A novel way to study the initial stages of soap-free emulsion polymerizations: The intercalation of polystyrene oligomers into hydrotalcite

The dominant species in the early stages of an emulsifier-free emulsion polymerization of styrene has been found to be an oligomer of two to three monomer units using a novel trapping technique. This involved the intercalation of charged primary oligomers between the layers of a hydrotalcite, [Mg₄Al₂(OH)₁₂]²⁺[A]^2- (where A = dianion). Hydrotalcites are an important class of lamellar, inorganic compounds whose interlayer spacing can be mod-ified by anion exchange. Our approach first involved preparing a hydrotalcite precursor in which the layers were propped apart by an organic dianion (terephthalate = TA). This material was then used to capture the negatively charged polystyrene oligomers from the emulsion polymerization reaction mixture. We found that TA was rapidly ion-exchanged for the charged oligomers. The resulting pillared hydrotalcite material was characterized using XRD and SEC. We found that the interlayer spacing between the hydroxide layers increased to 23.2 Å on exposure to the emulsion reaction mixture. This represents an interlayer expansion of 18.3 Å (after subtraction of the hydroxide layer contribution), which is cnsistent with intercalation of oligomers with two to three monomer units arranged in a bilayer. This size estimate was confirmed by the results of size exclusion chromatography. © 1995 John Wiley & Sons, Inc.     

Effects of particle size on the electrochemical performances of a layered double hydroxide, [Ni<Subscript>4</Subscript>Al(OH)<Subscript>10</Subscript>]NO<Subscript>3</Subscript>

In this paper, the electrochemical performances of a layered double hydroxide, [Ni₄Al(OH)₁₀]NO₃, of different particle sizes are studied. The results show that the particle size of the sample has evident effects on its discharge capacity at high current density, although a larger capacity may be observed for the bigger particles when they are discharged at lower current densities, e.g. 0.2 A g⁻¹. However, the capacity decreases more quickly than that of the sample in smaller particle size when the current density increases. For example, the discharge capacity of the smallest particle remains as high as 180 mAh·g⁻¹ even at very high current density, e.g. 4.0 A g⁻¹. The results also show that long time soaked electrodes in 7 mol l⁻¹ KOH have improved performance, especially for the hydrothermal samples. It also seems that there is an optimal size for materials, which can maintain their performance for longer time.     

Crystallochemical features of the anion varieties of aluminum and lithium binary hydroxide

Crystallochemical features of anion (Cl⁻, Br⁻, I⁻, NO ₃ ⁻ , CO ₃ ²⁻ , SO ₄ ²⁻ ) varieties of the aluminum and lithium hydroxide were studied by using the aluminum and lithium binary hydroxide (LiOH·2Al(OH)₃·2H₂O) model in space group P6₃cm with the tetrahedral coordination of lithium. Atomic coordinates corresponding to the lowered lattice symmetry were refined. Institute of Solid State Chemistry and Processing of Mineral Raw Materials, Siberian Branch, Russian Academy of Sciences. Novosibirsk State Pedagogical University. Translated fromZhurnal Struktumoi Khimii, Vol. 35, No. 5, pp. 158–170, September–October, 1994. Translated by T. Yudanova     

Incorporation of rare-earth ions in Mg-Al layered double hydroxides: intercalation with an [Eu(EDTA)] chelate

Reaction of an aqueous slurry of an Mg₂Al-NO₃ layered double hydroxide with a four-fold excess of Na[Eu(EDTA)] gives a material which analyses for Mg_0.68Al_0.32(OH)₂[Eu(EDTA)]_0.10(CO₃)_0.11·0.66H₂O. The interlayer spacing of the material is 13.8 Å, corresponding to a gallery height of 9.0 Å, which accords with the maximal dimensions (9-10 Å) of the anion in metal-EDTA complex salts as determined by single crystal X-ray diffraction. Geometrical considerations show that the charge density on the layered double hydroxide layers is too high to be balanced by intercalation of [Eu(EDTA)]⁻ alone, necessitating the co-intercalation of carbonate ions which have a much higher charge density.     

Intercalation of vanadate in Ni, Zn layered hydroxyacetates

Interlayer acetate anions in layered double hydroxyacetates of Ni²⁺ and Zn²⁺ have been exchanged by oxovanadates following three synthetic routes (at 60°C, under hydrothermal conditions and after preswelling with caprylate anions) and different pH; direct exchange at room temperature was not successful. Complete exchange was achieved under adequated conditions, and the precise nature of the interlayer anion depends on the pH during exchange: at low pH (4.5), the presence of α-VO₃ chains, with anchoring (grafting) of the species to the hydroxide layers, is proposed. At higher pH (9.5) V₂O₇⁴⁻ species are present in the interlayer. Thermal decomposition of these vanadate-intercalated products leads to formation of orthorhombic Ni²⁺ and Zn²⁺ vanadates, together with NiO.     

n(Mg)/n(Al)=3的水滑石层板结构及层间距的阴离子调控

利用密度泛函理论(DFT)的B3PW91方法在Lanl2dz水平上研究了镁铝摩尔比为3的水滑石层板分子簇模型[Mg30Al7(OH)72]9+的几何构型, 优化得到的结构参数和采用Reflex模块模拟得到的XRD图谱分别与实验观测结果相符, 由此确定了水滑石层板沿第三维方向的有序堆积, 该结构符合空间群R3m(166), 其晶胞参数a=1.2552 nm, c=2.3400 nm. 进一步构造了具有R3m空间群对称性的Mg-Al-CO32--LDH晶体结构模型, 选取其中的簇模型, 经优化得到了一种稳定构型, 脱除结晶水的水滑石层间距为0.7260 nm, 键参数的变化表明碳酸根离子与层板间存在较强的超分子作用.