Simultaneous Determination of Four Active Components in a Compound Formulation by Liquid Chromatography

Summary A rapid and accurate LC method is described for simultaneous determination of pseudoephedrine hydrochloride (PSE), acetaminophen (AMP), dextromethorphen hydrobromide (DEX), and diphenhydramine hydrochloride (DPH) in a compound formulation. Chromatographic separation of the four drugs was achieved on a Hypersil CN column (150 mm × 4.6 mm, 5 m particle) by use of a mobile phase comprising a mixture of 3 mM ion-pairing solution, 2% aqueous triethylamine solution, and 2 M phosphoric acid, 68:48:88 (v/v), pH 3.0, delivered at 1.0 mL min^–1. Compounds were detected at 215 nm and the run time was less than 10 min. The linearity, accuracy, and precision of the method were found to be acceptable over the concentration ranges 6.1–36.4 g mL^–1 for PSE, 65.0–390.0 g mL^–1 for AMP, 3.1–18.6 g mL^–1 for DEX, and 5.0–30.0 g mL^–1 for DPH.     

Determination of Triphenyltin and Its Metabolite Diphenyltin in Culture Medium by High-Performance Liquid Chromatography with UV detection

A method for the determination of triphenyltin and diphenyltin was developed by reversed-phase high-performance liquid chromatography with UV detection. Triphenyltin and diphenyltin were separated using a reversed-phase Symmetry C₁₈ column (150 × 3.9 mm, 5 m) with tetrahydrofuran-water-acetonitrile-glacial acetic acid (13:25:5:7, v/v) containing 0.05% triethylamine and 1.0% sodium acetate as mobile phase at 0.50 mL min^–1 and detection at 257 nm. The calibration curves were linear from 0.26 mol L^–1 to 1100 mol L^–1 for triphenyltin with a correlation coefficient of 0.9999 (n=12) and from 0.60 mol L^–1 to 1200 mol L^–1 for diphenyltin with a correlation coefficient of 0.9991 (n=12), respectively. The detection limits of triphenyltin and diphenyltin were 0.2 mol L^–1 and 0.4 mol L^–1, respectively. The method was successfully applied to the determination of triphenyltin and its metabolite diphenyltin in culture medium. The recoveries of triphenyltin and diphenyltin were in the ranges of 97.7% to 103.3% and 85.5% to 91.6%, respectively.     

Simultaneous Determination of Pioglitazone and Glimepiride by High-Performance Liquid Chromatography

A rapid and accurate HPLC method has been developed for simultaneous determination of pioglitazone and glimepiride. Chromatographic separation of the two pharmaceuticals was performed on a Cosmosil C₁₈ column (150 mm × 4.6 mm, 5 m) with a 45:35:20 (v/v) mixture of 0.01 m triammonium citrate (pH adjusted to 6.95 with orthophosphoric acid), acetonitrile, and methanol as mobile phase, at a flow rate of 1.0 mL min^–1, and detection at 228 nm. Separation was complete in less than 10 min. The method was validated for linearity, accuracy, precision, limit of quantitation, and robustness [1, 2]. Linearity, accuracy, and precision were found to be acceptable over the ranges 2.50–30.00 g mL^–1 for pioglitazone and 0.10–10.00 g mL^–1 for glimepiride.     

The oxidative addition of diphenylphosphine and monophenylphosphine to the electron-rich rhenium-rhenium triple bond. The isolation and characterization of compounds that contain the four-center Re(μ-X)(μ-PR2)Re cluster (X=halide)

Diphenylphosphine oxidatively adds to the ReRe bonds of Re₂ X ₄(-dppm)₂ (X=Cl or Br; dppm=Ph₂PCH₂PPh₂) and Re₂Cl₄(-dpam)₂ (dpam=Ph₂AsCH₂AsPh₂) to afford the dirhenium(III) complexes Re₂(-X)(-PPh₂)HX ₃(-LL)₂. The dppm complexes have also been prepared from the reactions of Re₂(-O₂CCH₃)X ₄(-dppm)₂ with Ph₂PH, and a similar strategy has been used to prepare Re₂(-Cl)(-PPh₂)HCl₃(-dmpm)₂ (dmpm=Me₂PCH₂PMe₂) from Re₂(-O₂CCH₃)Cl₄(dmpm)₂. Phenylphosphine likewise reacts with Re₂ X ₄(-dppm)₂ to give Re₂(-X)(-PHPh)HX ₃(-dppm)₂. An X-ray crystal structure determination on Re₂(-Cl)(-PPh₂)HCl₃(-dppm)₂ confirms its edge-shared bioctahedral structure. This complex crystallizes in the space group (No. 148) witha=21.699(3) Å, =84.50(4)°,V=10084(5) ų, andZ=6. The structure was refined toR=0.049 (R _w 0.069) for 5770 data withI>3.0(I). The Re-Re distance is 2.5918(7) Å. Oxidation of the bromide complex Re₂(-Br)(-PPh₂)HBr₃(-dppm)₂ with NOPF₆ produces the unusual dirhenium(III, II) cation [Re₂(-H)(-Br)[P(O)Ph₂]Br₂(NO)(-dppm)₂]⁺ which has been structurally characterized as its perrhenate salt, [Re₂(-H)(-Br)[P(O)Ph₂]Br₂(NO)(-dppm)₂]ReO₄ · 2CH₂Cl₂. This complex crystallizes in the space group (No. 2) witha=14.187(7) Å,b=16.419(5) Å,c=16.729(5) Å, =98.76(2)°, =110.11(3)°, =104.66(3)°,V=3414(6) ų,Z=2. The structure was refined toR=0.040 (R _w =0.051) for 5736 data withI>3.0(I). The presence of a phosphorus-bound [P(O)Ph₂]^– ligand, a linear nitrosyl and a bridging hydrido ligand has been confirmed. The Re-Re distance is 2.6273(8) Å.     

Addition of HCl to a Cluster-Bound Vinylidene Ligand: Preparation and Structure of Ru5(μ3-SMe)(μ3-CMe)(μ-Cl)(μ-SMe)(μ-PPh2)2(CO)9·PhMe

Addition of aqueous HCl to Ru₅( ₃-C=CH₂)(-SMe)₂(-PPh₂)₂(CO)₁₀ afforded the structurally characterized carbyne complex Ru₅( ₃-SMe)( ₃-CMe)(-Cl)(-SMe)(-PPh₂)₂(CO)₉, formed by addition of H to the vinylidene ligand; a Cl atom bridges an Ru–Ru bond.     

The composition of volatile and particulate hydrocarbons in urban air

Summary The hydrocarbon composition of the particle and gas phases in the urban atmosphere has been studied by filtration and parallel adsorption on active charcoal and polyurethane foam (PUF). Gas chromatography (GC) and GC coupled to mass spectrometry (GC-MS) have been used for the analysis of the organic matter extracts obtained with each system. In the case of the particle and PUF samples these extracts were fractionated into aliphatic and aromatic compounds. This approach has allowed to identify up to 247 hydrocarbon molecules showing that C0–C5 alkylbenzenes are the major compounds in the charcoal extracts whereas C14–C23 n-alkanes, C0–C4 alkylnaphthalenes, C0–C4 alkylbiphenyls and C3–C5 alkylbenzenes are those predominantly found in the PUF materials. The particles essentially contain C17–C38 n-alkanes and parent polycyclic aromatic hydrocarbons (PAH). These qualitative differences are paralleled by a progressive concentration decrease from the more to the less volatile hydrocarbons. Thus, the total charcoal extracts average 80 g/m³, the PUF compounds represent 4 /m³ and the particle hydrocarbons 0.7 g/m³. These latter airborne materials are essentially composed of petrogenic residues 0.6 g/m³ (aliphatic fraction) whereas the pyrolytic PAH only involve 0.08 g/m³.     

The relative importance of temperature and isotope effects on the dipole oscillator strength distribution of H2

Summary The calculation of the effects of temperature and isotopic composition on the energy weighted moments of the dipole oscillator strength distribution of H₂ in the random phase approximation to the polarization propagator are reported. It is seen that the effect of isotopic composition is small, while that of temperature is of an order accessible to experiment. We find that all the mean excitation energiesI , for =–1, 0, 1, decrease with temperature as does the dipole oscillator strength momentS() for >0, while the opposite is true for <0. These effects are interpreted in terms of the bond length dependence of the excitation energies.     

The oxidative addition of hydrogen sulfide to the electron-rich triple bond: The isolation and characterization of compounds that contain the Re2(μ-H)(μ-SH) cluster unit

The reactions of Re₂X₄(-dppm)₂ (X=Cl or Br; dppm=Ph₂PCH₂PPh₂) with H₂S in THF afford the dirhenium (III) complexes Re₂(-H)(-SH)X₄(-dppm)₂, the first examples of the oxidative addition of an S-H unit across an electron-rich metal-metal triple bond. The bromide complex Re₂(-H)(-SH)Br₄(-dppm)₂ (C₂H₅)₂O crystallizes in the space group P2₁/n witha=16.631(2) Å,b=15.967(3) Å,c=19.904(2) Å, =92.698(7)°,V=5279(2) ų, andZ=4. The structure which was refined toR=0.053 (R _w=0.070) for 4903 data withI>3.0(I), shows the presence of an edge-shared bioctahedral geometry with a very short Re-Re distance of 2.4566(7) Å. While the hydrogen atoms of the -H and -SH ligands were not located in the X-ray structure determination, their presence is confirmed by IR and¹H NMR spectroscopy.     

Titrimetric determination of thiourea and silver with a picrate ion selective electrode

Summary A method has been developed for the semiautomatic potentiometric titration of thiourea with silver nitrate and of silver with thiourea, in the presence of picrate ions, using a picrate ion selective electrode. Thiourea in the range 15–1500g and silver in the range 200–1800g were determined with relative errors and relative standard deviation of about 1%.

---

Zusammenfassung Eine halbautomatische potentiometrische Titrationsmethode für Thioharnstoff mit Silbernitrat bzw. umgekehrt in Gegenwart von Pikrationen mit Hilfe einer selektiven Pikratelektrode wurde entwickelt. 15–1500g Thioharnstoff bzw. 200–1800g Silber wurden mit einem relativen Fehler und einer relativen Standardabweichung von etwa ±1% bestimmt.

     

Path of “dry” electrons before localization in liquid hydrocarbons

Conclusions On the basis of measurements of values of in liquid hydrocarbons, it has been shown that the path length before localization of a photoliberated electron increases with increasing mobility of the excess electron, from approximately 40 Å (methylcyclohexane) to 200 Å (isooctane). In a liquid with10^–2 cm²/V·sec (methylcyclohexane, hexane), the localization takes place before or immediately after thermalization of the electron. In a liquid with>10^–1 cm²/V·sec, the electron passes through the main part of its path before localization, being in thermal equilibrium with the medium.Translated from Izvestiya Akademii Nauk SSSR, Seriya Khimicheskaya, No. 10, pp. 2198–2203, October, 1985.     

Thiazane-2, 4-dithione and its 3-aryl derivatives

Reaction of 2-thiothiazane-4-one and its 3-aryl derivatives with phosphorus pentasulfide in toluene or dichloroethane gives thiazane-2, 4-dithione, or the corresponding 3-aryl derivatives. The compounds are characterized by absorption maxima (or bends) at three bands, 244–262, 315–321, and 339–350 m. The IR spectra exhibit bands at 14.93 (C-S-C), 6.64, and 6.84 (N-C-S), and 7.34, 8.43, 7.14 (CH₂).     

Fällungsanalyse im Mikrogrammbereich: Eine neue Methode

Zusammenfassung Eine neue Methode zur Durchführung gravimetrischer Bestimmungen im Mikrogrammbereich wurde beschrieben; diese beruht im wesentlichen darauf, daß der Niederschlag nicht mehr zusammen mit dem Filter, sondern nach Überführen mit einem geeigneten Lösungsmittel in einem separaten Wägegefäß gewogen wird.Die dazu nötigen Geräte und deren Herstellung wurden beschrieben. Nach dieser Methode wurden folgende Bestimmungen mit zufriedenstellender Richtigkeit durchgeführt: 2,5–25g Al, 5–50g Cu und 5–50g Zn mit Oxin, 2,5–25g Fe(III) und 2,5–25g Ti(IV) mit N-Benzoyl-phenylhydroxylamin, 5–50g Ni und 5–50g Cu mit Salicylaldoxim, 2,5–50g Co(II) und 2,5–50g Fe(III) mit -Nitroso--naphthol sowie 5–50g Chlorid als Silberchlorid.

---

Precipitation analysis in the microgram-scale: A new method

Summary A new method for gravimetric determinations in the microgram-scale is described. This method is based on the fact that the precipitate is not weighed together with the filter but is transferred to a separate weighingvessel using a suitable solvent. The necessary simple devices and their use are described. The following determinations were carried out with satisfying accuracy: 2,5–25g Al, 5–50g Cu and 5–50g Zn with Oxine, 2,5–25g Fe and 2,5–25g Ti withN-benzoylphenylhydroxylamine, 5–50g Ni and 5–50g Cu with salicylaldoxime, 2,52–50g Co and 2,5–50g Fe with -nitroso--naphthol and 5–50g chloride as silver chloride.

     

Bestimmung von Ascorbinsäure auf Grund ihrer in einem Landolt-System ausgeübten reduzierenden Wirkung

Zusammenfassung Im Bromat-Jodid-Ascorbinsäure-System hängt die Zeit, die bis zur Jodausscheidung vergeht, von der Konzentration der Ascorbinsäure ab. Unter entsprechenden Versuchsbedingungen ist die Reaktionszeit proportional der Ascorbinsäurekonzentration. Danach kann die Ascorbinsäure sowohl mit Hilfe der Simultankomparationsmethode, als auch chronometrisch bestimmt werden. Die Genauigkeit ist ± 3% im Bereich von 5 bis 300g/5 ml. Die Grenzen der Bestimmung sind 1g bzw. 1000g Ascorbinsäure in 5 ml.

---

Determination of ascorbic acid on the basis of its reducing action in a landolt system

Summary In the bromate-iodide-ascorbic acid system, the time that elapses until the iodine appears is dependent on the concentration of the ascorbic acid. Under appropriate experimental conditions, the reaction time is proportional to the ascorbic acid concentration. Accordingly, the ascorbic acid may be determined with the aid not only of the simultaneous comparison method but also chronometrically. The precision is ± 3% in the 5–300g/5 ml range. The limits of the determination are 1g and 1000g ascorbic acid in 5 ml respectively.

     

Ionenaustauschchromatographie mit gepackten Capillars?ulen und amperometrischer Detektion

Zusammenfassung Herstellung und Anwendung gepackter Capillarsäulen (innerer Durchmesser: 0,3 mm) zur analytischen Trennung von Kationen durch Komplexelution im Mikromaßstab werden beschrieben. Als Säulenpackung dienen Kugeln eines stark sauren Kationenaustauschers mit einem mittleren Durchmesser von 25 . Die Detektion der getrennten Kationen erfolgt kontinuierlich im Effluent mit Hilfe einer amperometrischen Mikromeßzelle. Die Trennleistung einer 125 mm langen Capillarsäule wird am System Ni²⁺/Co²⁺/Iminodiessigsäure gezeigt. Die dosierten Probemengen liegen in der Größenordnung von 5–12 g je Kation.

---

Summary Preparation and application of packed capillary columns (interior diameter: 0.3 mm) for analytical separations of cations in micro-scale by means of complex elution are described. The capillary columns are filled with spherical grains in the range of 25 .The detection of separated cations in the effluent is performed by means of an amperometric micro-cell.The separation efficiency of a capillary column (length: 125 mm) is shown for the system Ni²⁺/Co²⁺/iminodiacetic acid. The injected quantities of samples are in the range of 5–12 g per cation.

---

---

Herrn Dr. habil. K. Wetzel danken wir für Anregungen und Diskussionen, den Herren W. Rose und K. Rupprecht für praktische Unterstützung bei der vorliegenden Arbeit.     

Bestimmung flüchtiger organischer Verbindungen in atmosphärischen Aerosolproben durch thermische Desorption und FID-Detektion

Zusammenfassung Staub- und Aerosolproben werden im Stickstoffstrom im Temperaturbereich 25–420° C einer temperaturprogrammierten thermischen Desorption unterworfen. Die flüchtigen organischen Komponenten werden mittels FID summarisch als volatile organic carbon (VOC) bestimmt. Die Eichung des Analysators erfolgt durch ein Aliphaten-Standardgemisch. Bei Probemengen von 50–100g Aerosol ist eine Bestimmung des VOC-Gehaltes mit einer Reproduzierbarkeit vons=3,5–7 rel.% möglich. Die Nachweisgrenze der Methode liegt für Aerosolproben bei 0,3g VOC.

---

Determination of volatile organic components in atmospheric aerosol samples by thermal desorption and FID-detection

Summary Atmospheric dust and aerosol samples are treated in a nitrogen carrier gas stream at the temperature range 25–420° C by temperature programmed desorption. The volatile organic components are detected by FID. Calibration of the analyzer is carried out with a standard mixture of aliphatic hydrocarbons. The result is expressed as volatile organic carbon (VOC). The reproducibility of the method for aerosol samples (sample weight 50–100g) is in the range of 3,5–7% r. s. d. The detection limit of the method is 0,3g VOC.

     

Crystal structure and spectroscopic study of di-μ(1,1)-azido-di-μ(0,0-nitrato)tetrakis(3,5-lutidine)dicopper(II), [Cu(N3) (NO3) (3,5-lutidine)2]2

A mixed ligand 12 complex of copper(II) azide with 3,5-lutidine, namely di-(1,1)-azido-di(0,0)-nitrato)tetrakis(3,5-lutidine)dicopper(II) has been prepared and characterized by X-ray crystallographic and spectroscopic methods. The dimeric molecule, which possesses a crystallographic inversion center, contains two(1,1) bridging azido ligands. Each copper(II) atom in the cyclic Cu₂N₂ unit is further coordinated by two oxygen atoms from two(0,0-nitrato) bridges at Cu-O distances of 2.465(3) and 2.568(3) Å and two nitrogen atoms from the lutidine molecules [Cu-N=2.003(3) and 2.012(3) Å] to give a distorted tetragonal bipyramid. Both azido ligands are linear [N-N-N angle=179.0(4) and asymmetric N-N=1.207(4) and N-N=1.135(5) Å]. The azido bridges produce a rather short Cu Cu distance of 3.013(2) Å. Infrared and electronic data are presented and discussed.     

Cluster Chemsitry. 96. Penta- and hexa-nuclear ruthenium cluster complexes derived from reactions of cyclopentadienes with Ru5(μ5-C2PPh2)(μ-PPh2)(CO)13

The reactions between Ru₅( ₅-C₂PPh₂)(gm-PPh₂(CO)₁₃ (1) and cyclopentadienes afforded the hexanuclear clusters Ru₆( ₆-C)( ₃-PPh₂)₂(CO)₁₀(-C₅ R ₅) [R ₅ = H₅ (2), H₄Me (3), Me₅ (4)] which contain an encapsulated carbide and a face-capping ₃-CH group, formed by cleavage of CC and CP bonds of the C₂PPh₂ moiety in1. In the reaction with cyclopentadiene, the unusual ligand C₁₃H₁₂O, formed by combination of C₂, CO and two molecules of C₅H₆ (or one molecule of dicyclopentadien), was characterized in the complex Ru₅( ₄-PPh) ( ₄-C₁₃H₁₂O)(-PPh₂(CO)₁₁(-C₅H₅) (5). In the reaction with pentamethylcyclopentadiene, the vinylidene complex Ru₅( ₃-CCHPh)( ₄-PPh)( ₄-PPh) (-PPh₂)(CO)₉(-C₅Me₅) (6) was also formed.     

Triiron and Triruthenium Carbonyl Clusters Bearing Bridging Long Chain Diphosphine and Capping Chalcogenido Ligands

Treatment of Ru₃(CO)₁₂ with dpphSe₂ (dpph = 1,6-bis(diphenylphosphino)hexane) in refluxing toluene in the presence of Me₃NO afforded two new compounds, Ru₃(CO)₇(-CO)(₃-Se)(-dpph) (1) and Ru₃(CO)₇(₃-Se)₂(-dpph) (2). A similar reaction of Ru₃(CO)₁₂ with dpppeSe₂ (dpppe = 1,5-bis(diphenylphosphino)pentane) gave exclusively Ru₃(CO)₇(₃-Se)₂(-dpppe) (3). Treatment of Ru₃(CO)₁₂ with dpphS₂ and dpppeS₂ at 110°C in the presence of Me₃NO afforded Ru₃(CO)₇(₃-S)₂(-dpph) (4) and Ru₃(CO)₇(₃-S)₂(-dpppe) (5), respectively. Reactions of Fe₃(CO)₁₂ with dpphSe₂ and dpppeSe₂, under identical conditions, afforded Fe₃(CO)₇(₃-Se)₂(-dpph) (6) and Fe₃(CO)₇(₃-Se)₂(-dpppe) (7), respectively. Compounds 1–7 were characterized spectroscopically and the molecular structures of compounds 1–4 were determined by single crystal X-ray crystallography. The core of 1 contains an equilateral triangle of ruthenium atoms with one capping selenium, one bridging dpph, one doubly bridging carbonyl and seven terminal carbonyl ligands. Complexes 2–4 have a square-pyramidal structure with two metal and two chalcogenide atoms alternating in the basal plane and the third metal atom at the apex of the pyramid, and belong to the family of well-known nido clusters with seven skeletal electron pairs.