Influence type of natural rubber on properties of green biodegradable thermoplastic natural rubber based on poly(butylene succinate)

Green biodegradable thermoplastic natural rubber (GB‐TPNR) based on simple blend of natural rubber (NR) and poly(butylene succinate) (PBS) was prepared using three NR alternatives: unmodified NR and epoxidized NR with 25‐ or 50‐mol% epoxide (ie, ENR‐25 or ENR‐50). It was found that ENR‐50/PBS blend showed the best compatibility, which resulted in superior mechanical and thermal properties with the highest crystallinity of the PBS phase, on comparing with the ENR‐25/PBS and NR/PBS blends. This might be attributed to stronger chemical interactions between the epoxide groups in ENR‐50 and the polar functional groups in PBS, which were confirmed by Fourier transform infrared (FTIR). Furthermore, scanning electron microscopy (SEM), atomic force microscopy (AFM), and polarizing optical microscopy (POM) micrographs of ENR‐50/PBS blend revealed phase separation with finer‐grained cocontinuous structure than in ENR‐25/PBS and NR/PBS simple blends. Furthermore, the chemical interactions in ENR‐50/PBS blend enhanced the resistance to accelerated weathering.     

Improving properties of natural rubber/polyamide 12 blends through grafting of diacetone acrylamide functional group

The aim of the present study was to improve the compatibility in blends of natural rubber (NR) and polyamide 12 (PA12) by grafting NR with hydrophilic monomer, diacetone acrylamide (DAAM), via seeded emulsion polymerization. The increase in polarity of NR after grafting modification was confirmed by a considerable increase in the polar component of its surface energy. Blends of graft copolymers of NR and poly(diacetone acrylamide) prepared using 10 wt% of DAAM (NR‐g‐PDAAM10) and PA12 were prepared at a 60/40 blend ratio (wt%) using simple blend and dynamic vulcanization techniques. The mechanical and rheological properties of the resulting blends were subsequently investigated and compared with those of the corresponding blends based on unmodified NR. The results show that dynamic vulcanization led to a significant increase in both mechanical and rheological properties of the blends. It was also observed that the dynamically cured NR‐g‐PDAAM10/PA12 blend had smaller particle size of vulcanized rubber dispersed in the PA12 matrix than observed for the dynamically cured NR/PA12 blend. This is due to the compatibilizing effect of DAAM groups present in NR‐g‐PDAAM10 molecule, which decreases the interfacial tension between the two polymeric phases. Therefore, it can be stated that the interfacial adhesion between NR and PA12 was improved by the presence of DAAM groups in NR molecule. This was reflected in the higher tensile properties observed in the dynamically cured NR‐g‐PDAAM10/PA12 blend. Copyright © 2017 John Wiley & Sons, Ltd.     

Influence of fluorine-containing lubricant on properties of NR/BR rubber

K95 experimental lubricant being a product of fluorine reaction with a blend of mutually soluble poly(fluorine alcohols) and poly(fluorine esters) with molecular weight 240-900 g/mol was studied as an additive for rubber compounds based on blend of NR and BR. It was thermally stable till 270-300 °C. For comparison, it was tested simultaneously with homogenizing agent, Struktol MS40. Lubricant K95 added in a quantity of 0.5 wt% reduced the viscosity of rubber compound; it also improved compound flow in the mold. Mechanical properties of cured rubber not decrease while resistance to abrasion and fatigue increased. K95 participated in forming strong physical junctions (lower molecular weight between junctions of thermally stable network) while Struktol MS40 reduced the networking degree of rubber. As a result, it acts a multifunctional additive for NR/BR rubber.     

Morphology dependence of crystallization of natural rubber in blends

Crystallization of natural rubber (NR) was investigated in different morphology for NR/styrene butadiene rubber (SBR) blend and NR/polystyrene-(b)-polyisoprene (SI)/polystyrene (PS) blend. A purified NR (PC-TE) was prepared from pale crape via transesterification. In the blends, PC-TE formed various morphologies; that is, matrix phase, island phase and continuous phase with a nano-scale, respectively, in dependence upon the ratio of the rubbers. The crystallization rate of the blends was also significantly associated with the morphology of the rubbers.     

丁苯橡胶/天然橡胶复合体系动态力学性能

生热;动态力学损耗;丁苯橡胶/天然橡胶复合体系动态力学性能     

Reinforcement of compatibilized NR/NBR blends by fly ash particles and precipitated silica

Effects of precipitated silica (PSi) and silica from fly ash (FA) particles (FASi) on the cure and mechanical properties before and after thermal and oil aging of natural rubber (NR) and acrylonitrile–butadiene rubber (NBR) blends with and without chloroprene rubber (CR) or epoxidized NR (ENR) as a compatibilizer have been reported in this paper. The experimental results suggested that the scorch and cure times decreased with the addition of silica and the compound viscosity increased on increasing the silica content. The mechanical properties for PSi filled NR/NBR vulcanizates were greater than those for FASi filled NR/NBR vulcanizates in all cases. The PSi could be used for reinforcing the NR/NBR vulcanizates while the silica from FA was regarded as a semi‐reinforcing and/or extending filler. The incorporation of CR or ENR enhanced the mechanical properties of the NR/NBR vulcanizates, the ENR being more effective and compatible with the blend. The mechanical properties of the NR/NBR vulcanizates were improved by post‐curing effect from thermal aging but deteriorated by the oil aging. Copyright © 2008 John Wiley & Sons, Ltd.     

Styrene butadiene rubber/epoxidized natural rubber blends: dynamic properties, curing characteristics and swelling studies

The dynamic properties, curing characteristics and swelling behaviour of styrene butadiene rubber (SBR) and epoxidized natural rubber (ENR) blends were studied. The incorporation of ENR 50 in the blends improved processability, stiffness, resilience and reduced the damping property. In terms of curing characteristics, the scorch time, t₂ and curing time, t₉₀ of the SBR/ENR blends decrease with increasing ENR content. At room temperature (23°C) and at 100°C the swelling degree of the SBR/ENR blends decreases with increasing ENR content.     

环氧化天然橡胶的研究进展

天然橡胶(NR)作为一种植物合成的可再生资源,与由石油生产的合成橡胶相比,更能满足当今世界普遍追求可持续发展的需要。NR的环氧化改性具有操作简单、方法经济、反应可在水相中进行的特点,制备得到的环氧化天然橡胶(ENR)具有良好的相容性、抗湿滑性、低的滚动阻力、耐油性和气密性等特点,在轮胎工业、胶粘剂和新型复合材料等领域中有着广泛的应用前景。本文对近年来ENR制备和表征方法、ENR与白炭黑之间的相互作用、ENR的硫化及其在轮胎胶料中的应用等方面的最新进展进行了综述,并对今后的研究方向提出了建议。     

Investigation of adhesion and mobility of polyurethane and epoxy-rubber glues and adhesives

The values of activation parameters in uncured and cured epoxy resins, rubbers, and blends thereof are investigated. The dependences of activation energy and adhesion strength of epoxy-rubber compositions on rubber content are determined. The correlation of adhesion and activation energy values for polyurethane rubber and epoxy-rubber compositions is shown.     

Effects of epoxidized natural rubber as a compatibilizer in melt compounded natural rubber-organoclay nanocomposites

Nanocomposites containing natural rubber (NR) as matrix, epoxidized natural rubber (ENR) as compatibilizer and organophilic layered clay (organoclay) as filler were produced in an internal mixer and cured using a conventional sulphuric system. The effects of ENR with 25 (ENR 25) and 50 mol% epoxidation (ENR 50), respectively, were compared at 5 and 10 parts per hundred rubber (phr) concentrations. The organoclay content was fixed at 2 phr. Cure characteristics, clay dispersion, (thermo)mechanical properties of the nanocomposites were determined and discussed. Incorporation of ENR and organoclay strongly affected the parameters which could be derived from Monsanto MDR measurements. Faster cure and increased crosslink density were attributed to changes in the activation/crosslinking pathway which was, however, not studied in detail. The organoclay was mostly intercalated according to X-ray diffraction (XRD) and transmission electron microscopic (TEM) results. The best clay dispersion was achieved by adding ENR 50. This was reflected in the stiffness of the nanocomposites derived from both dynamic mechanical thermal analysis (DMTA) and tensile tests. The tensile and tear strengths of the ENR 50 containing nanocomposites were also superior to the ENR 25 compatibilized and uncompatibilized stocks.