马来酸酐-苯乙烯熔融接枝聚丙烯的影响因素及其性能研究

用单螺杆挤出机制备了马来酸酐 (MAH) 苯乙烯 (St)对聚丙烯 (PP)的多组分单体自由基熔融接枝体系 .研究证实了当两种单体物质的量比约为 1∶1时 ,接枝物的接枝率最高 ,而熔体流动速率 (MFR)最大 .对反应体系影响因素的研究表明单体用量和引发剂用量对不同单体用量比的系列接枝物的接枝率会产生不同的影响 ;另外 ,单体用量增加 ,接枝物的MFR减小 ,过氧化二异丙苯 (DCP)用量增加 ,接枝物的MFR增加 .对多单体熔融接枝聚丙烯PP g (MAH co St)的力学性能研究发现 ,选用合适的单体用量比、单体用量和DCP用量时 ,所制备的接枝物可具有与纯PP相当或更佳的力学性能     

1,6-己二醇二丙烯酸酯和苯乙烯多单体熔融接枝制备长支链聚丙烯研究

采用哈克转矩流变仪制备了1,6-己二醇二丙烯酸酯(HDDA)和苯乙烯(St)多单体熔融接枝聚丙烯(PP)体系.红外测试结果表明St的加入能够促进HDDA接枝到PP主链,提高接枝率.动态流变行为研究结果也表明采用多单体熔融接枝PP更有利于体系在熔融接枝中生成长支链(LCB).随着St单体添加量的增加,HDDA的接枝率增大...     

ABS的MAH/St多单体熔融接枝及其对PA6/ABS共混体系相形态和力学性能的影响

通过多单体熔融接枝的方法制备出了具有较高接枝率的ABS接枝物 (ABS g (MAH co St) ) ,并对其接枝机理进行了初步探讨 .研究表明 ,MAH、St接枝ABS时 ,反应主要发生在ABS中聚丁二烯的双键部位 .同时 ,当MAH与St的用量比约为 1:1时接枝率达到最高 .ABS g (MAH co St)作为尼龙 6 (PA6 ) ABS共混体系相容剂起到了良好的增容效果 .实验证明 ,相容剂使用前后 ,共混物的相区尺寸由几十 μm减小到 1μm以下 ,且分布更加均匀 ;共混物的拉伸强度和冲击强度等力学性能也同时得到均衡改善 .     

淀粉乙酸酯的阴离子接枝己内酯聚合研究

将淀粉在二甲基甲酰胺、吡啶存在下 ,以乙酸酐进行部分乙酰化 ,制备取代度为 0 7～ 1 9的淀粉乙酸酯 (St Ac) .以萘钠与淀粉乙酸酯中残余的羟基反应 ,将羟基转化为醇盐 (ONa) ,引发己内酯进行阴离子开环接枝聚合 ,合成了淀粉 聚己内酯接枝共聚物 (St g PCL) .采用凝胶渗透色谱法 (GPC)研究了接枝前后聚合物分子量的变化情况 ,并以接枝率、单体转化率对接枝反应进行了表征 .研究了接枝条件如温度、溶剂、引发剂和单体的用量对接枝率及单体转化率的影响 .研究发现随着反应温度升高 ,接枝率、单体转化率呈S曲线变化 ,单体浓度、引发剂浓度的增大有利于接枝反应的进行 .     

甲基丙烯酸缩水甘油酯/苯乙烯固相接枝聚丙烯

以苯乙烯(St)为共单体，过氧化苯甲酰(BPO)为引发剂，采用固相接枝反应将甲基丙烯酸缩水甘油酯(GMA)接枝到聚丙烯(PP)大分子链上。研究了反应时间、单体用量、引发剂用量等因素对接枝率的影响。采用凝胶渗透色谱(GPE)测定了PP和接枝物PP-g-(GMA-St)的分子量和分子量分布。结果 表明固相接枝PP反应条件为[GMA／[St]=2，反应3．5h，加入GMA 10份，BPO 5份。St的加入有助于GMA与PP的接枝，同时在一定程度上抑制了PP的降解。     

多官能团单体对马来酸酐接枝聚丙烯流变行为的影响

研究了多官能团辅助单体偏苯三酸三丙烯酯(TATM)对马来酸酐接枝聚丙烯的熔体流动速率(MFR)和流变行为的影响.当以不含抗氧剂的聚丙烯粉料为原料时,TATM的加入对稳定接枝产物MFR的效果并不理想.但将聚丙烯粉料添加抗氧剂并造粒后,TATM的加入则可有效稳定体系的MFR,各种流变曲线显示出接枝产物的熔体弹性明显提高,说明有枝化或交联结构出现.针对PP粉料和粒料间接枝产物流变行为存在的重大差异,结合熔体自由基接枝反应的机理进行了解释.TATM能够起到稳定MFR的效果是由于其提高了接枝物的熔体弹性,从而抵消了聚丙烯熔体接枝反应中所不可避免的β断链所造成的剪切黏度下降.聚丙烯粉料和粒料中抗氧剂的差异对聚丙烯的加工降解有严重影响,造成了TATM在不同聚丙烯体系中效果的差异.     

GMA/苯乙烯多组分单体接枝聚丙烯结晶行为研究

使用差示扫描量热计 (DSC)研究了甲基丙烯酸缩水甘油酯 苯乙烯 (GMA St)多单体熔融接枝聚丙烯[PP g (GMA co St) ]的等温和非等温结晶行为 ,用偏光显微镜观察了结晶的形态 ,并利用Avrami方程对其结晶动力学进行了分析 .研究发现接枝聚丙烯的结晶模式与PP相似 ,属于异相成核控制的球晶三维生长 ;但接枝聚丙烯的结晶温度 (Tc)显著提高 ,幅度高达 16～ 19℃ ,总结晶速率与纯PP相比明显加快 .接枝聚丙烯上GMA co St支链的存在 ,降低了成核界面自由能 ,促进了聚丙烯结晶的异相成核 .在接枝率不太高的情况下 ,随着接枝率的提高 ,接枝聚丙烯的结晶温度升高 ,总结晶速率加快 .在高接枝率范围内 ,随着接枝率的提高 ,接枝PP的Tc 不再升高 ,且由于接枝链的增长严重阻碍了球晶生长 ,导致接枝PP的总结晶速率反而随接枝率的升高而下降     

分子结构对丙烯酸酯类单体接枝LLDPE影响的研究

利用HAAKE密炼机对比研究了甲基丙烯酸缩水甘油酯(GMA)、甲基丙烯酸羟丙酯(HPMA)、甲基丙烯酸羟乙酯(HEMA)、甲基丙烯酸乙酯(EMA)、甲基丙烯酸甲酯(MMA)以及丙烯酸羟乙酯(HEA)等具有不同分子结构的丙烯酸酯类单体对线性低密度聚乙烯(LLDPE)的接枝反应.通过对不同温度下不同反应时间的产物接枝率的测定,发现丙烯酸酯类单体接枝聚烯烃过程中均存在解聚现象.开始发生解聚现象的温度,也即解聚温度(ceiling temperature,Tc),与单体分子结构有关.讨论了位阻效应和特殊基团(如羟基等)相互作用对解聚温度的影响,并通过丙烯酸酯类单体的溶液聚合反应确认了不同丙烯酸酯类单体的解聚温度范围.讨论了添加苯乙烯(St)作为助单体对不同丙烯酸酯类单体接枝率的影响,并结合Q-e法则和竞聚率对其进行了解释.     

PVDF基两性离子交换树脂的辐射合成及性能

以聚偏氟乙烯(PVDF)树脂为基材,采用共辐射接枝方法,在PVDF树脂上接枝苯乙烯(St)/甲基丙烯酸二甲氨基乙酯(DMAEMA)二元单体,随后对接枝产物进行磺化和质子化反应引入磺酸基和叔氨基正离子得到了一种新型的PVDF基两性离子交换树脂.红外光谱、X射线光电子能谱(XPS)、热重和扫描电镜(SEM)分析证明了辐射引发接枝共聚及功能化反应的成功进行.接枝反应条件如溶剂、剂量和二元单体浓度对接枝率(GY)有明显的影响.随着接枝率的增加,功能树脂的离子交换容量随之增大,但接枝链St与DMAEMA的摩尔比不变,其阳离子及阴离子交换容量最大分别可达2.16 mmol/g,1.06 mmol/g.     

St存在下MAH熔融接枝PP机理的探讨

在哈克转矩流变仪和双螺杆挤出机中,对苯乙烯（St）存在下马来酸酐（MAH）熔融接枝聚丙烯（PP）进行了研究.实验表明：St的加入不仅可显著提高MAH的接枝率,而且可减少PP的降解;当St和MAH的摩尔比为1时,MAH接枝率最大.通过反应机理分析得出：没有St时,MAH主要以单分子形式在PP降解之后接枝到PP上;而在St存在下,St与MAH以交替接枝的形式或者配合物（CTC）形式在PP降解之前接枝到PP上,形成St和MAH交替聚合的长链.后者使MAH的接枝率增加,同时增大了PP的交联,减小了PP的降解.     

GRAFTING OF PEROXIDE-INITIATED MALEIC ANHYDRIDE ON SPHERICAL PE／PP IN-REACTOR BLEND GRANULES

Spherical polyethylene/polypropylene (PE/PP) in-reactor blend granules with various ethylene/propylene molar ratios and high porosity were synthesized using a high yield TiCl4/MgCl2 supported catalyst. A solution of benzoyl peroxide (BPO)/maleic anhydride (MAH)/xylene (interfacial reagent) or BPO/MAH/St (comonomer) was absorbed onto the PE/PP inreactor blend granules, and solid phase gratt polymerization of MAH on PE/PP was conducted. The amount of grafted MAH on PE/PP was measured through chemical titration. The results showed that solid phase graft polymerization of MAH in PE/PP in-reactor blend granules produced graft copolymer with high amount of grafted MAH, and the amount of grafted MAH was raised slightly when St was introduced as comonomer. The graft in-reactor blend was fractionated into five fractions through temperature-gradient extraction fractionation (TGEF), and the fractions were analyzed by FTIR. The results revealed that MAH is mainly grafted on the PE segments, whereas MAH was predominantly grafted on the PP segments when St was present in the graft polymerization system. In addition, the final product is still in the form of regular spherical granules, which is beneficial for industrial processing.     

接枝和交联对纳米SiO_2改性NR/PP共混型热塑弹性体的影响

动态硫化制备纳米二氧化硅(SiO2)改性天然橡胶/聚丙烯共混型热塑性弹性体(NR/PP TPE).研究了马来酸酐/苯乙烯/过氧化二异丙苯(MAH/St/DCP)多单体“就地”熔融接枝、交联对TPE力学性能、耐溶剂性能和耐热变形性能的影响,并用SEM分析了TPE的断面形貌.结果表明:纳米SiO2和MAH/St/DCP的最佳质量分数分别为0.03和0.0375/0.0188/0.00375时,MAH/St/DCP接枝、交联改性NR/PP/纳米SiO2TPE的力学性能、耐溶剂性能和耐热变形性能最佳.MAH/St/DCP“就地”接枝、交联通过细化交联NR分散相、改善交联NR分散的均匀性和增加两相之间的共交联,使NR与PP两相界面结合强度明显提高,NR/PP TPE的综合性能得到明显的改善.     

接枝和交联对纳米Si02改性NR／PP共混型热塑弹性体的影响

动态硫化制备纳米二氧化硅（SiO2）改性天然橡胶，聚丙烯共混型热塑性弹性体（NR/PPTPE）．研究了马来酸酐，苯乙烯，过氧化二异丙苯（MAH／St／DCP）多单体“就地”熔融接枝、交联对TPE力学性能、耐溶剂性能和耐热变形性能的影响，并用SEM分析了TPE的断面形貌．结果表明：纳米SiO2和MAH／St／DCP的最佳质量分数分别为0．03和0．0375／0．0188／0．00375时，MAH／St／DCP接枝、交联改性NR／PP／纳米SiO：TPE的力学性能、耐溶剂性能和耐热变形性能最佳．MAH／St／DCP“就地”接枝、交联通过细化交联NR分散相、改善交联NR分散的均匀性和增加两相之间的共交联，使NR与PP两相界面结合强度明显提高，NR／PPTPE的综合性能得到明显的改善．     

Graft copolymerization of maleic anhydride/styrene onto isotactic polypropylene using supercritical CO2

The free‐radical grafting of maleic anhydride (MAH) and styrene (St) onto isotactic polypropylene (iPP) was studied by thermal decomposition of dicumyl peroxide (DCP) using supercritical CO₂ as a solvent and swelling agent. Several effects of molar ratio of monomer, soaking temperature and time, reaction time, and reaction pressure on the graft degree were discussed. It was found that the addition of St to the grafting system as a comonomer could significantly enhance the graft degree of the grafted PP. Under the optimal reaction condition, the maximum of iPP grafting MAH and St in supercritical CO₂ medium was 10.58%. The chemical structures and properties of grafting copolymers were characterized by Fourier transform infrared spectroscopy (FTIR) and differential scanning calorimetry (DSC). The results showed that the supercritical CO₂ method had noticeable advantages over the existed method when compared, such as a lower temperature, a higher graft degree, easy separation, and environmentally benign. Copyright © 2007 John Wiley & Sons, Ltd.     

Grafting copolymerization of styrene and maleic anhydride binary monomer systems induced by UV irradiation

Photografting copolymerization of maleic anhydride (MAH) and styrene (St) onto LDPE film was investigated by using a one-step method, and further thermally induced grafting copolymerization of them was carried out by using a two-step method. Regarding the photografting copolymerization of MAH/St binary monomer system, both conversion percentage (CP) and grafting efficiency (GE) increased with raising the content of MAH in the monomer feed. In addition, the content of MAH in the grafted copolymers also increased with increasing the fraction of MAH in the monomer feed. The formation of LDPE-g-P(MAH-co-St) grafted film was identified by FTIR and ESCA spectroscopy. In the case of grafting copolymerization of MAH/St by the two-step method, grafting copolymerization proceeded slowly compared with the non-grafting copolymerization. The apparent activation energy (E_a) for the non-grafting copolymerization in the solution and the grafting copolymerization on LDPE film was 24 and 82 kJ/mol, respectively, which were noticeably lower than those of MAH/vinyl acetate (MAH/VAC) binary monomer system under the similar grafting conditions. These data of E_a explained why the grafting copolymerization of styrene/MAH took place faster than that of MAH/VAC binary monomer system. The composition of the grafted copolymer chains was largely affected by the composition of the monomer feeds; however, the composition of the non-grafted copolymers nearly remained at 1/1 even in systems with largely different MAH/styrene ratios in monomer feeds. It is indicated that the non-grafting copolymerization proceeded predominantly following alternating copolymerization, but the grafting copolymerization performed random copolymerization.     

Radiation-induced graft polymerization of maleic acid and maleic anhydride onto ultra-fine powdered styrene–butadiene rubber (UFSBR)

The functionalization of ultra-fine powdered styrene–butadiene rubber (UFSBR) was carried out using gamma radiation-induced graft polymerization of maleic acid (MA) and maleic anhydride (MAH), respectively. It was found that the graft yield of MA onto UFSBR increased rapidly up to the peak and then decreased with increasing MA content. Moreover, the peak shifted to the direction of lower MA content with increasing absorbed dose. Similarly, there was the peak of graft yield with increasing MAH content for grafting of MAH onto UFSBR, whereas the peak of graft yield was achieved at 10 wt% MAH content at different absorbed doses. On the other hand, increasing absorbed dose and decreasing monomer contents are useful to improve the graft efficiency of MA and MAH. At high dose and low monomer content, the graft yield of MAH onto UFSBR is higher than that of MA. FTIR spectra confirmed that both MA and MAH can be grafted successfully onto the UFSBR under gamma irradiation, respectively. Comparing with maleation of rubber by melt grafting, the graft yield of MAH on UFSBR is higher, which can be attributed to the network structure and nanometer size of UFSBR as well as high energy provided by radiation.     

Grafting of maleic anhydride onto linear polyethylene: A Monte Carlo study

Monte Carlo simulation was used to study the graft of maleic anhydride (MAH) onto linear polyethylene (PE‐g‐MAH) initiated by dicumyl peroxide (DCP). Simulation results revealed that major MAH monomers attached onto PE chains as branched graft at higher MAH content. However, at extremely low MAH content, the fraction of bridged graft was very close to that of branched graft. This conclusion was somewhat different from the conventional viewpoint, namely, the fraction of bridged graft was always much lower than that of branched graft under any condition. Moreover, the results indicated that the grafting degree increased almost linearly to MAH and DCP concentrations. On the other hand, it was found that the amount of grafted MAH dropped sharply with increasing the length of grafted MAH, indicating that MAH monomers were mainly attached onto the PE chain as single MAH groups or very short oligomers. With respect to the crosslink of PE, the results showed that the fraction of PE‐(MAH)_n‐PE crosslink structure increased continuously, and hence the fraction of PE‐PE crosslink decreased with increasing MAH concentration. Finally, quantitative relationship among number average molecular weight of the PE, MAH, and DCP contents was given. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5714–5724, 2004