Evaluation of Electrochemically Reduced Gold Nanoparticle—Graphene Nanocomposites for the Determination of Dopamine

Two gold nanoparticle-graphene nanocomposites were electrochemically obtained by the one-step constant potential coreduction of graphene oxide and gold ions or the electrodeposition of gold nanoparticles on graphene oxide followed by electrochemical reduction of graphene oxide. The surface morphology, electron transfer rate, and electrocatalytic activity toward the oxidation of dopamine on these nanocomposites were systematically studied. The results showed that both preparations synthesized gold nanoparticle-graphene nanocomposites. The nanocomposite obtained by the one-step synthesis showed higher electron transfer kinetics and electrocatalytic activity toward dopamine than the material obtained by the two-step synthesis. Consequently, the one-step nanocomposite was used to modify a glassy carbon electrode to form a dopamine sensor. Differential pulse voltammetry was used to detect dopamine with a detection limit of 0.1 micromolar and a linear dynamic range from 0.2 to 20 micromolar. The sensor displayed good stability, high reproducibility, and was used for the determination of dopamine in human urine.     

Label‐free Electrochemical Aptasensor for Carcino‐embryonic Antigen Based on Ternary Nanocomposite of Gold Nanoparticles,Hemin and Graphene

In this report, a label‐free electrochemical aptasensor for carcino‐embryonic antigen (CEA) was successfully developed based on a ternary nanocomposite of gold nanoparticles, hemin and graphene nanosheets (AuNPs‐HGNs). This nanocomposite was prepared by decorating gold nanoparticles on the surface of hemin functionalized graphene nanosheets via a simple wet‐chemical strategy. The aptamer can be assembled on the surface of AuNPs‐HGNs/GCE (glassy carbon electrode) through Au‐S covalent bond to form the sensing interface. Hemin absorbed on the graphene nanosheets not only acts as a protective agent of graphene sheets, but also as an in situ probe base on its excellent redox properties. Gold nanoparticles provide with both numerous binding sites for loading CEA binding aptamer (CBA) and good conductivity to promote the electron transfer. The current changes, which are caused by CEA specifically binding on the modified electrode, are exploited for the label‐free detection of CEA in a very rapid and convenient protocol. Therefore, the method has advantages of high sensitivity, wide linear range (0.0001–10 ng mL^?1), low detection limit (40 fg mL^?1) and attractive specificity. The results illustrate that the proposed label‐free electrochemical aptasensor has a potential application in the biological or clinical target analysis for its simple operation and low cost.     

Tannic Acid Modified Electrochemical Biosensor for Glucose Sensing Based on Direct Electrochemistry

A novel glucose biosensor was constructed through the immobilization of glucose oxidase (GOx) on gold nanoparticles (Au NPs) deposited, and chemically reduced graphene oxide (rGO) nanocomposite. In the synthesis, tannic acid (TA) was used for the reduction of both graphene oxide, and Au³⁺ to rGO, and Au NPs, respectively. Also, by harnessing the π‐π interaction between graphene oxide and TA, and protein‐TA interaction, a novel nanocomposite for the fabrication of a third generation biosensor was successfully constructed. Upon the oxidation of TA to quinone, which is easily reducible at the negative potential range, enhanced electron transfer was obtained. The cyclic voltammetry (CV) results demonstrated a pair of well‐defined and quasi‐reversible redox peaks of active site molecule of GOx. The biosensor exhibited a linear response to glucose concentrations varying from 2 to 10 mM with a sensitivity of 18.73 mA mM⁻¹ cm⁻². The fabricated biosensor was used for the determination of glucose in beverages.     

Tunable Catalytic Performance and Selectivity of a Nanoparticle–Graphene Composite through Finely Controlled Nanoparticle Loading

Graphene‐based composites offer enhanced catalytic performance of metal and semiconductor nanoparticles, but their development is challenging because catalytic performance strongly depends on the structure and composition of the composite. Herein we show that the catalytic performance of a nanoparticle–graphene composite is very dependent on catalyst loading, which can be optimized for simultaneous enhancement of activity and selectivity. A glassy carbon working electrode has been modified with a gold nanoparticle–graphene (Au–G) composite with a varied number of gold nanoparticles per graphene, so that the conducting property of graphene and the electrocatalytic property of the metal were effectively coupled to give the best catalytic activity and selectivity. The modified electrode was used for simultaneous electrochemical detection of a mixture of electroactive species with high sensitivity. This result shows that the catalytic performance of a graphene‐based composite is sensitive to the catalyst loading and should be optimized for the best performance.     

Multilayer‐Functionalized Reduced Graphene Oxide Decorated with Gold Nanoparticles as a Designed Nanonanocatalyst for the Selective Oxidation of Cyclohexene by Molecular Oxygen in a Solvent‐Free System

The aerobic oxidation of cyclohexene is of great significance from the viewpoints of both fundamental and industry studies as it can transfer the petrochemical feedstock into valuable chemicals. In this research, gold nanoparticles were synthesized on the multi‐layer functionalized reduced graphene oxide . The surface of reduced graphene oxide (rGO) was modified with hydrophobic and hydrophilic layers to create the rGO with scattered hydrophilic positions. The gold nanoparticles were synthesized and immobilized simultaneously in small hydrophilic micro reactors in a mild condition. Characterization of synthesized nanocatalyst was confirmed with different techniques such as TEM, XRD, FT‐IR, and SEM. TEM images of synthesized catalyst show the gold nanoparticles have diameters less than 5 nm. Designed nanonanocatalyst was investigated for the selective liquid phase oxidation of cyclohexene with molecular oxygen in solvent free condition which after optimized conditions a maximum of 88% conversion and 91% selectivity was obtained.     

Electrocatalytic Oxidation of Ethanol on the Surface of Graphene Based Nanocomposites: An Introduction and Review to it in Recent Studies

This review gives an overview of the electrochemical investigations about the properties of various types of graphene composites in the ethanol oxidation. Various routes to provide appropriate graphene‐based materials required electrochemical techniques for investigation of different types of the materials as well as their performance and efficacy in ethanol oxidation are discussed in detail. Furthermore, it is demonstrated that the incorporation of suitable materials, e. g. noble metals (graphene‐supported binary and ternary metal nanoparticles), metal oxides, conductive polymer, etc, with graphene results in excellent electrocatalytic activity, superb durability and selectivity in ethanol oxidation. Immobilization of electrocatalytically active NPs on graphene supports using physical approaches is considered as an effective route to prepare direct ethanol fuel cell (DEFC) anode catalysts.     

Mild Synthesis of Pt/SnO2/Graphene Nanocomposites with Remarkably Enhanced Ethanol Electro‐oxidation Activity and Durability

We have designed a new Pt/SnO₂/graphene nanomaterial by using L ‐arginine as a linker; this material shows the unique Pt‐around‐SnO₂ structure. The Sn²⁺ cations reduce graphene oxide (GO), leading to the in situ formation of SnO₂/graphene hybrids. L ‐Arginine is used as a linker and protector to induce the in situ growth of Pt nanoparticles (NPs) connected with SnO₂ NPs and impede the agglomeration of Pt NPs. The obtained Pt/SnO₂/graphene composites exhibit superior electrocatalytic activity and stability for the ethanol oxidation reaction as compared with the commercial Pt/C catalyst owing to the close‐connected structure between the Pt NPs and SnO₂ NPs. This work should have a great impact on the rational design of future metal–metal oxide nanostructures with high catalytic activity and stability for fuel cell systems.     

Sucrose‐Assisted Loading of LiFePO4 Nanoparticles on Graphene for High‐Performance Lithium‐Ion Battery Cathodes

A simple approach for loading LiFePO₄ (LFP) nanoparticles on graphene (G) that could assemble amorphous LiFePO₄ nanoparticles into a stable, crystalline, graphene‐modified layered materials (G‐S‐LFP, S=sucrose) by using graphene as building block and sucrose as a linker has yet to be developed. On the basis of differential scanning calorimetric and transmission electron microscopy analysis of the samples from controlled experiment, a possible mechanism was proposed to explain the “linker” process of LFP and graphene with sucrose as the linker. The electrochemical properties of the samples as cathode material for lithium‐ion batteries were studied by cyclic voltammogrametry and galvanostatic methods. Results showed that G‐S‐LFP displayed superior lithium‐storage capability with current density changes randomly form 0.5 to 10 C. The significant improvement for rate and cycle performance could be attributed to the high conductivity of the graphene host, the high crystallinity, and the layered structure.     

Composite Assembly of Silver Nanoparticles with Avidin and Biotinylated AChE on Gold for the Pesticidal Electrochemical Sensing

An amperometric pesticide biosensor has been devised by the composite assembly of silver nanoparticles with avidin and biotinylated acetylcholinesterase (AChE) on gold electrodes modified with a biotin‐terminated self assembly monolayer (SAM). This composite assembly strategy takes use of the biospecific recognition avidin with the biotin from the SAM‐terminals and biotinylated AChE, as well as the electrostatic interaction between silver nanoparticles with negatively charged citrate shell and avidin with encounter charge at pH 7.2. The construction process of the composite interface on gold was monitored by surface plasmon resonance (SPR), and its structure was characterized by attenuated total reflection Fourier‐transform infrared spectra, atomic force microscopy and UV‐vis spectra. The composite interface shows excellent electron transfer ability, as characterized by cyclic voltammetry and electrochemical impedance spectroscopy. Under the optimum conditions a quantitative measurement of organophosphate pesticide dimethoate was achieved with the linear range of 0.05 μM to10 μM and the detection limit 0.01 μM, taken as the concentration equivalent to a 10% decrease in signal. Silver nanoparticles conjugated biotin‐avidin system represents a simple and functional approach to the integration of electrode sensing interface with improved biocompatibility and electron transfer ability, which may provide an analytical access to a large group of enzymes for bioelectrochemical application.     

Electrochemical Sensor for Sensitive Determination of Capsaicin Using Pd Decorated Reduced Graphene Oxide

In this work, the reduced graphene oxide functionalized with poly dimethyl diallyl ammonium chloride (PDDA) modified palladium nanoparticles (PDDA‐rGO/Pd) had been facile synthesized and used as the sensing layer for sensitive determination of capsaicin. The prepared composite was characterized by transmission electron microscopy, UV‐visible absorption spectroscopy. The image demonstrated that Pd nanoparticles were uniformly distributed on the graphene surface. The electrochemical properties of the prepared sensor were investigated by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The results showed that the nanocomposite exhibits attractive electrocatalytic activity towards the oxidation of capsaicin. This attributed to the synergistic action of the excellent properties of Pd nanoparticles and graphene nanosheets. Under optimized conditions, the electrochemical sensor possessed a dynamic linear range from 0.32 μM to 64 μM with a detection limit of 0.10 μM (S/N=3) for capsaicin detection. Moreover, the cost‐effective and simple fabrication procedure, good reproducibility and stability as well as acceptable accuracy for capsaicin determination in actual samples are also the main advantages of this method, which might have broad application in other amide alkaloid detection.     

Electrochemical synthesis of a graphene sheet and gold nanoparticle-based nanocomposite, and its application to amperometric sensing of dopamine

We describe a simple, green and controllable approach for electrochemical synthesis of a nanocomposite made up from electrochemically reduced graphene oxide (ERGO) and gold nanoparticles. This material possesses the specific features of both gold nanoparticles and graphene. Its morphology was characterized by scanning electron microscopy which reveals a homogeneous distribution of gold nanoparticles on the graphene sheets. Cyclic voltammetry was used to evaluate the electrochemical properties of this nanocomposite towards dopamine by modification of it on surface of glassy carbon electrode (GCE). Compared to the bare GCE, the electrode modified with gold nanoparticles, and the electrode modified with ERGO, the one modified with the nanocomposite displays better electrocatalytic activity. Its oxidation peak current is linearly proportional to the concentration of dopamine (DA) in the range from 0.1 to 10?μM, with a detection limit of 0.04?μM (at S/N?=?3). The modified electrode also displays good storage stability, reproducibility, and selectivity.

石墨烯负载高活性Pd催化剂对乙醇的电催化氧化

以石墨粉为原料, 采用Hummers法液相氧化合成了氧化石墨(GO), 然后用化学一步还原制得石墨烯负载钯催化剂. X射线衍射(XRD)、透射电镜(TEM)表征表明, Pd在石墨烯载体上有较好的分散度, 粒径为3-5 nm. 电化学活性面积(EASA)、循环伏安(CV)、计时电流(CA)和计时电位(CP)等电化学测试表明, 与传统Pd/Vulcan XC-72相比, Pd/石墨烯催化剂对碱性介质中乙醇电催化氧化的催化活性有了很大的提高.     

石墨烯负载高活性Pd催化剂对乙醇的电催化氧化

以石墨粉为原料, 采用Hummers法液相氧化合成了氧化石墨(GO), 然后用化学一步还原制得石墨烯负载钯催化剂. X射线衍射(XRD)、透射电镜(TEM)表征表明, Pd在石墨烯载体上有较好的分散度, 粒径为3-5 nm. 电化学活性面积(EASA)、循环伏安(CV)、计时电流(CA)和计时电位(CP)等电化学测试表明, 与传统Pd/Vulcan XC-72相比, Pd/石墨烯催化剂对碱性介质中乙醇电催化氧化的催化活性有了很大的提高.     

石墨烯负载高活性Pd催化剂对乙醇的电催化氧化

以石墨粉为原料,采用Hummers法液相氧化合成了氧化石墨(GO),然后用化学一步还原制得石墨烯负载钯催化剂.X射线衍射(XRD)、透射电镜(TEM)表征表明,Pd在石墨烯载体上有较好的分散度,粒径为3-5nm.电化学活性面积(EASA)、循环伏安(CV)、计时电流(CA)和计时电位(CP)等电化学测试表明,与传统Pd/VulcanXC-72相比,Pd/石墨烯催化剂对碱性介质中乙醇电催化氧化的催化活性有了很大的提高.     

石墨烯负载高活性Pd催化剂对乙醇的电催化氧化

以石墨粉为原料, 采用Hummers法液相氧化合成了氧化石墨(GO), 然后用化学一步还原制得石墨烯负载钯催化剂. X射线衍射(XRD)、透射电镜(TEM)表征表明, Pd在石墨烯载体上有较好的分散度, 粒径为3-5 nm. 电化学活性面积(EASA)、循环伏安(CV)、计时电流(CA)和计时电位(CP)等电化学测试表明, 与传统Pd/Vulcan XC-72相比, Pd/石墨烯催化剂对碱性介质中乙醇电催化氧化的催化活性有了很大的提高.     

石墨烯负载高活性Pd催化剂对乙醇的电催化氧化

以石墨粉为原料, 采用Hummers法液相氧化合成了氧化石墨(GO), 然后用化学一步还原制得石墨烯负载钯催化剂. X射线衍射(XRD)、透射电镜(TEM)表征表明, Pd在石墨烯载体上有较好的分散度, 粒径为3-5 nm. 电化学活性面积(EASA)、循环伏安(CV)、计时电流(CA)和计时电位(CP)等电化学测试表明, 与传统Pd/Vulcan XC-72相比, Pd/石墨烯催化剂对碱性介质中乙醇电催化氧化的催化活性有了很大的提高.     

石墨烯负载高活性Pd催化剂对乙醇的电催化氧化

以石墨粉为原料, 采用Hummers法液相氧化合成了氧化石墨(GO), 然后用化学一步还原制得石墨烯负载钯催化剂. X射线衍射(XRD)、透射电镜(TEM)表征表明, Pd在石墨烯载体上有较好的分散度, 粒径为3-5 nm. 电化学活性面积(EASA)、循环伏安(CV)、计时电流(CA)和计时电位(CP)等电化学测试表明, 与传统Pd/Vulcan XC-72相比, Pd/石墨烯催化剂对碱性介质中乙醇电催化氧化的催化活性有了很大的提高.     

石墨烯负载高活性Pd催化剂对乙醇的电催化氧化

以石墨粉为原料, 采用Hummers法液相氧化合成了氧化石墨(GO), 然后用化学一步还原制得石墨烯负载钯催化剂. X射线衍射(XRD)、透射电镜(TEM)表征表明, Pd在石墨烯载体上有较好的分散度, 粒径为3-5 nm. 电化学活性面积(EASA)、循环伏安(CV)、计时电流(CA)和计时电位(CP)等电化学测试表明, 与传统Pd/Vulcan XC-72相比, Pd/石墨烯催化剂对碱性介质中乙醇电催化氧化的催化活性有了很大的提高.     

石墨烯负载高活性Pd催化剂对乙醇的电催化氧化

以石墨粉为原料, 采用Hummers法液相氧化合成了氧化石墨(GO), 然后用化学一步还原制得石墨烯负载钯催化剂. X射线衍射(XRD)、透射电镜(TEM)表征表明, Pd在石墨烯载体上有较好的分散度, 粒径为3-5 nm. 电化学活性面积(EASA)、循环伏安(CV)、计时电流(CA)和计时电位(CP)等电化学测试表明, 与传统Pd/Vulcan XC-72相比, Pd/石墨烯催化剂对碱性介质中乙醇电催化氧化的催化活性有了很大的提高.     

石墨烯负载高活性Pd催化剂对乙醇的电催化氧化

以石墨粉为原料, 采用Hummers法液相氧化合成了氧化石墨(GO), 然后用化学一步还原制得石墨烯负载钯催化剂. X射线衍射(XRD)、透射电镜(TEM)表征表明, Pd在石墨烯载体上有较好的分散度, 粒径为3-5 nm. 电化学活性面积(EASA)、循环伏安(CV)、计时电流(CA)和计时电位(CP)等电化学测试表明, 与传统Pd/Vulcan XC-72相比, Pd/石墨烯催化剂对碱性介质中乙醇电催化氧化的催化活性有了很大的提高.