羊毛负载钯络合物的合成及其加氢催化作用

以天然生物高分子羊毛为载体制备了羊毛－钯络合物催化剂。用ＸＰＳ、ＩＲ方法对羊毛－钯络合物进行了初步表征。证明羊毛－钯络合物在常温常压下能够催化各种化合物，如硝基苯、苯甲醛、丙烯醇、丁烯睛、醋酸乙烯酯、苯乙烯和１－己烯的加氢，分别以大约１００％的收率得到了苯胺、苯甲醇、正丙醇、丙胺、醋酸乙酯，乙苯和己烷。对于用以往的催化剂较难加氢的各种脂肪醛，如丙醛、丁醛、戊醛和己醛，在常温常压下也能够进行催化加氢，分别以大约１００％的收率得到正丙醇、正丁醇、正戊醇和正己醇。这种催化剂稳定性也很高，长时间反应也能保持高活性，钯不脱落。     

高活性氨基胍树脂负载Pd(0)配合物的催化性能研究

以氨基碳酸胍改性氯球为载体, 与氯化钯溶液反应并还原制备氨基胍树脂负载钯(0)催化剂. 对催化剂进行了FT-IR, XRD, BET, TG-DTA表征. 研究了该催化剂对各种取代卤代苯与丙烯酸、苯乙烯的Heck芳基化反应催化性能. 实验结果表明, 该催化剂对活性(吸电子基)溴代苯和碘苯具有良好的催化活性, 对含活性吸电子基的溴代苯(4-溴苯甲醛和4-溴硝基苯)于140 ℃时能在22 min内完成Heck 芳基化反应; 催化剂具有较好的重复使用性能, 在90 ℃下催化碘苯与丙烯酸的反应循环21次时仍能保持良好的催化活性. 反应机理研究表明: 催化反应的活性组分是可溶性钯物种; 可溶性钯是由卤代苯与催化剂表面上的钯氧化加成所致.     

高活性氨基胍树脂负载Pd(0)配合物的催化性能研究

以氨基碳酸胍改性氯球为载体,与氯化钯溶液反应并还原制备氨基胍树脂负载钯(0)催化剂.对催化剂进行了FT-IR,XRD,BET,TG-DTA表征.研究了该催化剂对各种取代卤代苯与丙烯酸、苯乙烯的Heck芳基化反应催化性能.实验结果表明,该催化剂对活性(吸电子基)溴代苯和碘苯具有良好的催化活性,对含活性吸电子基的溴代苯(4-溴苯甲醛和4-溴硝基苯)于140℃时能在22min内完成Heck芳基化反应;催化剂具有较好的重复使用性能,在90℃下催化碘苯与丙烯酸的反应循环21次时仍能保持良好的催化活性.反应机理研究表明:催化反应的活性组分是可溶性钯物种;可溶性钯是由卤代苯与催化剂表面上的钯氧化加成所致.     

水溶性含钌-铂双金属催化剂催化卤代芳香硝基化合物选择性加氢

考察了水溶性Ru/Pt-TPPTS双金属催化剂催化卤代芳香硝基化合物的加氢性能.实验结果表明,在Ru-TPPTS中添加铂或钯后,反应活性明显提高,尤其是Ru/Pt-TPPTS双金属催化剂更表现出显著的双金属协同效应.在pH₂=1.0MPa,70℃,反应2h的条件下,双金属催化剂0.50Ru/0.50Pt-TPPTS催化对-氯硝基苯加氢生成对-氯苯胺的反应转化率达到100%.对于取代基和取代位置不同的一些卤代硝基苯加氢,该双金属催化剂也表现出很高的催化活性和生成卤代苯胺的选择性,脱卤反应的程度很小.     

高活性氨基胍树脂负载Pd(O)配合物的催化性能研究

以氨基碳酸胍改性氯球为载体,与氯化钯溶液反应并还原制备氨基胍树脂负载钯(O)催化剂.对催化剂进行了FT-IR,XRD,BET,TG-DTA表征.研究了该催化剂对各种取代卤代苯与丙烯酸、苯乙烯的Heck芳基化反应催化性能.实验结果表明,该催化剂对活性(吸电子基)溴代苯和碘苯具有良好的催化活性,对含活性吸电子基的溴代苯(4-溴苯甲醛和4-溴硝基苯)于140℃时能在22 min内完成Heck芳基化反应;催化剂具有较好的重复使用性能,在90℃下催化碘苯与丙烯酸的反应循环21次时仍能保持良好的催化活性.反应机理研究表明:催化反应的活性组分是可溶性钯物种;可溶性钯是由卤代苯与催化剂表面上的钯氧化加成所致.     

有机硅聚合物过渡金属络合催化剂的合成与活性(X)——聚γ-(m-二苯膦苯基)丙基硅氧烷铂络合物在氢化反应中的催化活性

有机硅聚合物为载体的过渡金属三苯膦络合物,文献中只报道过聚γ-(p-二笨膦苯基)丙基和聚δ-(p-二苯膦苯基)丁基硅氧烷铑络合物,过去,我们曾合成了聚γ-(m-二苯膦苯基)丙基硅氧烷钯络合物,并证明了它是烯烃和硝基苯氢化的良好催化剂,本文报道上述高分子配位基与铂的络合物的结构与它在氢化反应中的催化特性。     

聚γ-(m-二苯胂苯基)丙基硅氧烷铂络合物的合成及其催化硅氢化性能

硅氢化反应在有机硅化学和有机硅工业中占有重要地位。早期广泛使用氯铂酸异丙醇体系作为催化剂,70年代后开始用四(三苯膦)合铂、氯化三(三苯膦)合铑等均相络合催化剂,但相应的胂络合物的催化硅氢化的研究报道极少,迄今只看到四(三苯胂)合钯、二卤化二(三苯胂)合镍、氯化二(三苯胂)(羰基)合铑等个别报道,以及三苯胂作为氯铂酸助催化剂的报道。     

Pd-Fe/吸附树脂催化剂的结构及其对卤代芳香硝基化合物的催化加氢性能

Ｐｄ┐Ｆｅ／吸附树脂催化剂的结构及其对卤代芳香硝基化合物的催化加氢性能吴琼（湖北大学化学系，武汉４３００６２）李翔张曼征（湖北省化学研究所，武汉４３００７４）关键词负载型催化剂，钯，铁，吸附树脂，氯硝基苯，加氢卤代芳香硝基化合物的加氢产物卤芳胺广泛用...     

聚-γ-N-(β-丁硫基乙基)胺丙基硅氧烷钯络合物的合成及其催化性能的研究

报导了聚－γ－Ｎ－（β－丁硫基乙基）胺丙基硅氧烷和氯化钯的反应，得到固载在二氧化硅上的聚－γ－Ｎ－（β－丁硫基乙基）胺丙基硅氧烷钯络合物，并用ＸＰＳ研究其结构．选用硝基苯、烯丙基环氧丙基醚、烯丙基苯基醚、丙烯腈、烯丙基苯、苯乙烯、环己烯及丁烯等８种底物进行催化加氢，以评价其催化活性．结果表明，该催化剂催化效果良好，并且有很好的稳定性．     

聚铝氨烷－铂络合物催化α－萘酚选择性氢化反应的研究

本文研究了二氧化硅负载的聚铝氨烷－铂络合物在α－萘酚选择性氢化反应中的催化性能。发现此催化剂在３０—５０℃和０．１ＭＰａ的温和条件下，对α－萘酚的氢化反应具有较高的催化活性和选择性。当α－萘酚的转化率达１００％时，目的产物５，６，７，８－四氢－α－萘酚的选择性高于８０％。考察了络合物中Ｎ／Ｐｔ摩尔比、反应温度、时间、溶液的ｐＨ值和溶剂等反应条件对催化活性及选择性的影响，此催化剂重复使用三次后，催化活性和选择性未见明显下降，具有良好的稳定性。     

Dechlorination of 2,4-dichlorophenoxyacetic acid using biochar-supported nano-palladium/iron: Preparation,characterization, and influencing factors

In the present study, peanut shell, a green waste raw material, was used to prepare biochar (BC) and to obtain BC-supported nano-palladium/iron (BC-nPd/Fe) composites for removing 2,4-dichlorophenoxyacetic acid (2,4-D) from water. Characterization analysis demonstrated that nPd/Fe particles were well dispersed on the BC surface with weakened magnetic properties. The average particle diameter and specific surface area of nPd/Fe were 101.3 nm and 6.7 m² g⁻¹, whereas the corresponding values of the BC-nPd/Fe materials were 88.8 nm and 14.8 m² g⁻¹, respectively. Several factors were found to influence the dechlorination of 2,4-D, including the weight ratio of BC to Fe, Pd loading ratio, initial solution pH, 2,4-D concentration, and reaction temperature. Dechlorination results indicated that the 2,4-D removal and phenoxyacetic acid (PA) generation rates were 44.1% and 20.1%, respectively, in the nPd/Fe system, and 100.0% and 92.1%, respectively, in the BC-nPd/Fe system. The dechlorination of 2,4-D was well described by the pseudo-first-order kinetic model (R² > 0.97), and the observed rate constants k_obs were 0.0042 min (nPd/Fe) and 0.0578 min (BC-nPd/Fe), respectively. The reaction mechanism indicated that the dechlorination hydrogenation was the main process to remove 2,4-D from water in the BC-nPd/Fe system. In addition, BC inhibited the formation of a passivation layer on the particle surface during the reaction, thus maintaining the high reactivity of BC-nPd/Fe. The easy preparation technique, high 2,4-D dechlorination capacity, and mild reaction conditions suggest that BC-nPd/Fe may be a promising alternative composite to remove 2,4-D from water.     

Aqueous-phase synthesis of PAA in PVDF membrane pores for nanoparticle synthesis and dichlorobiphenyl degradation

This paper deals with bimetallic (Fe/Pd) nanoparticle synthesis inside the membrane pores and application for catalytic dechlorination of toxic organic compounds form aqueous streams. Membranes have been used as platforms for nanoparticle synthesis in order to reduce the agglomeration, encountered in solution phase synthesis which leads to a dramatic loss of reactivity. The membrane support, polyvinylidene fluoride (PVDF) was modified by in situ polymerization of acrylic acid in aqueous phase. Subsequent steps included ion exchange with Fe²⁺, reduction to Fe⁰ with sodium borohydride and Pd deposition. Various techniques, such as STEM, EDX, FTIR and permeability measurements, were used for membrane characterization and showed that bimetallic (Fe/Pd) nanoparticles with an average size of 20–30 nm have been incorporated inside of the PAA-coated membrane pores. The Fe/Pd-modified membranes showed a high reactivity toward a model compound, 2,2′-dichlorobiphenyl and a strong dependence of degradation on Pd (hydrogenation catalyst) content. The use of convective flow substantially reduces the degradation time: 43% conversion of dichlorobiphenyl to biphenyl can be achieved in less than 40 s residence time. Another important aspect is the ability to regenerate and reuse the Fe/Pd bimetallic systems by washing with a solution of sodium borohydride, because the iron becomes inactivated (corroded) as the dechlorination reaction proceeds.     

含氨基酸侧链的有机硅高分子催化剂——聚γ-(色氨酸基)丙基硅氧烷钯催化剂的合成及加氢活性

本世纪60年代以来,Overberser等把存在于酶中的催化基团引入聚合物中,合成了一系列类酶聚合物催化剂。氨基酸是酶分子中的重要组成部分,它们分子中所含的氨基、羧基等均可络合金属离子形成催化剂的活性中心,氨基酸残基又可造成不同的配位环境,因此,用氨基酸作侧链合成类金属酶高分子催化剂有可能提高催化活性和选择性。     

含氨基酸侧链的有机硅高分子催化剂——聚γ-(色氨酸基)丙基硅氧烷钯催化剂的合成及加氢活性

This paper was concerned with synthesis of poly-y-(L-tryptophan) propylsiloxane palladium complex catalysts in different -COOH/Pd ratio. The data indicated that the hydrogenation activity of the title catalyst was very high. Initial rate of styrene hydrogenation was 4972 mlH₂/min. mmol Pd when the -COOH/Pd, mol ratio 4.5:1. Besides, the hydrogenation activity increased with the increasing of the -COOH/Pd mol ratio. The influence of polar solvent was higher than nonpolar solvent.     

Highly chemoselective hydrogenation with retention of the epoxide function using a heterogeneous Pd/C-ethylenediamine catalyst and THF

In general, palladium-carbon (Pd/C) catalyzed hydrogenation of epoxides affords the corresponding primary and secondary alcohols as a mixture. It has been found that the catalytic activity of a Pd/C -ethylenediamine complex catalyst [Pd/C(en)] in the hydrogenolysis of epoxide functions is drastically reduced. Herein we describe a mild and chemoselective method for the hydrogenation of olefin, nitro, and azide functions with retention of the epoxide function. The chemoselectivity was accomplished by using a combination of 5% Pd/C(en) and THF as solvent. A significant drop in the chemoselectivity of the hydrogenation is observed with 5% Pd/C(en) in MeOH. These results reinforce the utility of epoxides as important precursors of alcohols in synthetic chemistry.     

Catalytic Dechlorination of Chlorobenzene in Water by Pd／Fe System

Chlorobenzene was dechlorinated by Pd/Fe bimetallic system in water through catalytic reduction. The dechlorination rate increases with increase of bulk loading of Pd due to the increase of both the surface loading of the Pd and the total surface area. For conditions with 0.005% Pd/Fe, 45% dechlorination efficiency was achieved within 5 h. The dechlorinated reaction is believed to take place on the bimetal surface in a pseudo-first-order reaction, with the rate constant being 0.0043 min^-1.     

Mechanism and influence factors of 2,4-D dechlorination by sodium citrate-activated bimetallic palladium-zero valent iron nanoparticles

Nanoscale zero-valent iron (nZVI) has high removal efficiency and strong reductive ability to organic contaminants, but this reactivity soon ceases and is attributed to rapid passivation of the nZVI surface due to the formation of iron oxides. In the present study, bimetallic palladium-zero valent iron nanoparticles were activated with sodium citrate (SC-nPd/Fe) to enhance 2,4-D dechlorination from aqueous solutions. FTIR and XRD analyses showed that there was no passivation layer on the surface of nZVI after the addition of SC, and XPS analysis confirmed the nZVI after the reaction still maintained high reactivity and surface Pd ratio. The existence of SC facilitated the transfer of electrons from Fe⁰ to contaminants, thus accelerating the reductive dechlorination of 2,4-D. The dechlorination efficiency of 2,4-D on nPd/Fe was only 56.4% in 210 min, while complete dechlorination could be achieved on SC-nPd/Fe under the same conditions, and simultaneously 97.1% of phenoxyacetic acid (PA) was generated. Moreover, the effect of reaction conditions on the dechlorination such as Pd ratio, SC dosage, initial pH and temperature was also investigated, and it was well described by pseudo-first-order kinetic model. In particular, The chelating abilities of SC is similar to EDTA, but it is an environmentally-friendly chelating agent. Findings from the present study suggested that the SC could be a promising substitute for application in the remediation of 2,4-D contained water.     

Solvent-free selective hydrogenation of chloronitrobenzene to chloroaniline over a robust Pt/Fe3O4 catalyst

In the absence of solvent, highly selective hydrogenation of o-chloronitrobenzene and m-chloronitrobenzene, with selectivity to the corresponding chloroanilines of ≥99.4% and complete conversion of the substrates, was realized over a robust Pt/Fe(3)O(4) catalyst which was prepared by adsorbing Pt nanoclusters on a Fe(3)O(4) support.     

Heterogeneous Hydrogenation with Hydrogen Spillover Enabled by Nitrogen Vacancies on Boron Nitride-Supported Pd Nanoparticles

Heterogeneous hydrogenation with hydrogen spillover has been demonstrated as an effective route to achieve high selectivity towards target products. More effort should be paid to understand the complicated correlation between the nature of supports and hydrogenation involving hydrogen spillover. Herein, we report the development of the hydrogenation system of hexagonal boron nitride (h-BN)-supported Pd nanoparticles for the hydrogenation of aldehydes/ketones to alcohols with hydrogen spillover. Nitrogen vacancies in h-BN determine the feasibility of hydrogen spillover from Pd to h-BN. The hydrogenation of aldehydes/ketones with hydrogen spillover from Pd proceeds on nitrogen vacancies on h-BN. The weak adsorption of alcohols to h-BN inhibits the deep hydrogenation of aldehydes/ketones, thus leading to high catalytic selectivity to alcohols. Moreover, the hydrogen spillover-based hydrogenation mechanism makes the catalyst system exhibit a high tolerance to CO poisoning.     

2-乙基蒽醌在双金属整体式催化剂上的氢化反应: 实验和DFT研究

过氧化氢(H2O2)是一种绿色化工原料和环境友好氧化剂. 目前, 超过 98% 的H2O2是通过蒽醌法生产. 蒽醌法主要包括 2-乙基蒽醌氢化生成 2-乙基氢蒽醌和 2-乙基氢蒽醌氧化生成 2-乙基蒽醌和H2O2的过程. 其中, 2-乙基蒽醌氢化是关键步骤. 在氢化过程中, 生成的 2-乙基氢蒽醌和四氢-2-乙基氢蒽醌是目标产物, 同时生成许多副产物. 目前, Pd 颗粒催化剂是广泛使用的催化剂, 但是蒽醌氢化过程中, 质量传递是主要的控制因素. 与颗粒催化剂对比, 整体式催化剂可以减弱整个反应的内外扩散, 提高反应速率. 很多研究结果显示, 整体式催化剂的传质优于颗粒催化剂, 可以提高催化效率. 近期许多研究显示, 双金属颗粒催化剂在很多氢化反应中体现出优异的催化性能. 本工作制备了双金属整体式催化剂, 考察了其在蒽醌氢化过程中的催化性能.首先, 通过浸渍法制备了4 种双金属整体式催化剂 Pd-M/SiO2/COR (M = Ni, Fe, Mn和 Cu)以及Pd/SiO2/COR和Ni/SiO2/COR两种单金属整体式催化剂. 催化活性结果显示, Ni/SiO2/COR的H2O2产量低于 Pd/SiO2/COR, 而且在 700 oC还原的 Pd-Ni/SiO2/COR 整体式催化剂在 Pd/M = 2 时取得了最高选择性 (95.3%) 和H2O2产量 (7.5 g/L). 然后, 考察了金属负载量的影响. 结果显示, 在金属负载量低于 0.4% 时, 随着金属负载量增加, 选择性和H2O2产量增加, 在金属负载量高于0.4% 时, 随着金属负载量增加, 选择性和H2O2产量降低. TEM结果表明, 添加第二种金属后, 双金属整体式催化剂颗粒尺寸变小, 分布更均匀. EDS结果显示, 双金属形成了合金. H2-TPR结果显示, 随着Pd/M比率增加, 还原温度降低, 说明Pd有助于第二种金属氧化物的还原. 这可能是由于 Pd 表面的氢溢流到第二种金属 (Ni, Fe, Mn和 Cu) 表面. 此外, 文献结果表明, 合金的形成能够抑制 PdH 的形成. 本工作表明添加第二种金属 (Ni, Fe, Mn和Cu) 后, PdH 的峰强度减弱或者峰消失, 也说明形成了合金. XPS 结果显示, 添加第二种金属后,在 336.3 ± 0.1 和 341.4 ± 0.1 eV 出现了新的 Pd 3d5/2和 Pd 3d3/2峰, 说明形成了合金. H2-O2滴定结果表明, Pd-Ni/SiO2/COR的Pd分散度和Pd比表面积都高于其他双金属催化剂, 说明第二种金属 Ni 更有利于促进 Pd 的分散, 减弱颗粒集聚, 揭示了Pd 和 Ni 之间强烈的相互作用. DFT 计算结果显示, Pd3M1(M = Ni, Fe, Mn和Cu) 双金属整体式催化剂和 2-乙基蒽醌之间的结合能低于 Pd/SiO2/COR和 2-乙基蒽醌之间的结合能, 但是 Pd3M1(M = Ni, Fe和Mn) 双金属催化剂和 2-乙基氢蒽醌之间的结合能减小得很少, 这可能是由于 2-乙基蒽醌的 C=O 和第二种金属之间具有强烈相互作用的缘故. Pd3Cu1双金属催化剂和 2-乙基氢蒽醌之间的结合能减小很多, 主要是由于 Pd3Cu1表面不利于 2-乙基氢蒽醌的吸附.因此, Pd-Ni/SiO2/COR 比 Pd/SiO2/COR, Ni/SiO2/COR 和其他的双金属整体式催化剂具有更高的选择性和H2O2产量, 主要是由于合金的形成以及 2-乙基氢蒽醌的 C=O 双键和 2-乙基氢蒽醌强烈的相互作用.