邻联甲苯胺-过氧化氢催化光度法测定钴

１引言 在碱性介质中,痕量Ｃｏ（Ⅱ）见对Ｈ２Ｑ２氧化邻联甲苯胺（ｏ－Ｔｏｌｉｄｉｎｅ）的显色反应具有强烈的催化作用,探讨了利用该反应进行痕量Ｃｏ（Ⅱ）测定的影响因素,建立了测定痕量Ｃｏ（Ⅱ）的催化动力学光度法,该方法的灵敏度为１．７８ × １０－６ｇ／Ｌ,测定的线性范围为０．８～３．６ μｇ／Ｌ Ｃｏ２＋,应用于维生素Ｂ１２中痕量Ｃｏ（Ⅱ）的测定,结果满意。２实验部分２．１仪器与试剂 ７２１－１００型分光光度计;电热恒温水浴槽;Ｎｉｃｏｌｅｔ ＦＴ－ＩＲ ５ＤＸ红外光谱仪。钴（Ⅱ）标准溶液：１ｍｇ／Ｌ;…     

甲苯浮选三元配合物光度法测定痕量钴的研究

本文提出了利用甲苯浮选钴－硫氰酸铵－孔雀石绿三元配合物体系痕量钴的方法。本法灵敏度高，精密度较好，除Ｃｕ＾２＋，Ｚｎ＾２＋外其余共存离子基本元干扰，适于水样中痕量钴的测定。     

测定钴的化学发光新体系

研究了新吖啶衍生物９，１０－二甲基吖啶氟磺酸盐的化学发光特性。建立了测定Ｃｏ６２＋的化学发光新体系。方法线性范围为１．０×１０＾－１０－１．０×１０＾－７ｇ／ｍＬ；检测限为５．０×１０＾－１１ｇ／ｍＬＣｏ＾２＋。测定５．０×１０＾－９ｇ／ｍＬＣｏ６２＋的相对标准偏差为６．０％。方法选择性好，用于自来水，江水，池塘水中痕量钴的测定，结果令人满意。     

烟草中Fe,Co一阶导数分光光度法同时测定的研究

本文研究了在ｐＨ４．０时，ｍｅｓｏ－四（４－磺酸基苯基）卟啉与铁、钴同时络合显色的反应条件以及一阶导数光谱行为。此体系一阶导数的灵敏度比零阶导数灵敏度高。Ｆｅ￣（３＋）～０．１８μｇ／ｍＬ、Ｃｏ￣（２＋）０～０．２４μｇ／ｍｌ，范围内符合比耳定律；检测限为：Ｆｅ￣（３＋）＝０．４８ｎｇ／ｍＬ，Ｃｏ￣（２＋）＝０．２ｎｇ／ｍＬ。回收率为：Ｆｅ９８．５％～１００．８％，Ｃｏ９９．２％～１０１．３％。此方法用于烟草中痕量Ｆｅ、Ｃｏ测定，与ＡＡＳ值相比较，结果令人满意。     

醇合成用改良铜钴催化体系的表征

应用ＸＰＳ能谱技术和合成气中压反应等对醇合成用铜钴基催化体系进行了表征研究。还原后的铜钴催化剂样品表面上钴以Ｃｏ＾２＋和Ｃｏ＾２＋形式共存，铜主要是Ｃｕ＾０物种。在反应条件下处理后，发生了再氧化现象，即钴主要以Ｃｏ＾２＋形式存在，铜变为Ｃｕ＋或Ｃｕ＾３＋物种。从催化剂的ＸＰＳ和ＸＡＥＳ结果可知，铜和钴之间具有强有相互作用和电荷转移。改良铜钴催化剂具有良好的醇合成的反应活性和碳链增长，助剂钼在样品还     

化学发光—流动注射—胶束增敏连续测定钴铬研究

基于钴（Ⅱ）和铬（Ⅲ）对鲁米诺－过氧化氢化学发光反应均有催化作用，加入ＣＴＭＡＢ能明显提高发光的信噪比，可测定亚纳克量的钴和铬，加入ＥＤＴＡ掩蔽钴（Ⅱ）测得铬（Ⅲ）量，再由钴和铬总量求得钴（Ⅱ）量，实现钴和铬的不经分离而流动注射连续测定。此法线性范围宽达４个数量级（１０－１１～１０－７ｇ／ｍＬ），检测下限低（Ｃｏ２＋１．２×１０－１１ｇ／ｍＬ，Ｃｒ３＋１．０×１０－１１ｇ／ｍＬ），再现性好，工效高（１２０个样品／ｈ），用于三种矿泉水中痕量钴（Ⅱ）、铬（Ⅲ）连续测定，结果良好     

催化动力学光度法测定痕量钴的研究

本文提出了钴（Ⅱ）催化Ｈ２Ｏ２氧化茜素红Ｓ褪色反应体系的新催化光度法。本方法灵敏度高，选择性好，精密度高（测２μｇＣｏ（Ⅱ）６次，ＲＳＤ＝１．４３％）适用于水样中痕量钴（Ⅱ）的测定。     

2－（2－噻唑偶氮）－5－〔N，N－二羧基甲基）氨基〕苯酚的分析特性和钴测定的研究

研究了新显色剂２－（２－噻唑偶氮）－５－［（Ｎ，Ｎ－２羧基甲基）氨基］苯酚（ＴＡＤＣＡＰ）与金属离子的显色反应，着重探讨了试剂与Ｆｅ￣（３＋）、Ｃｏ￣（２＋）、Ｎｉ￣（２＋）、Ｃｕ￣（２＋）、Ｚｎ￣（２＋）、Ｍｎ￣（２＋）显色反应的最佳条件，测定了这些络合物的络合比和稳定常数等，同时建立了钴的分析方法，并用于维生素Ｂ＿（１２）注射液中Ｃｏ￣（２＋）的测定。     

微晶萘固相萃取分离富集及ICP—AES测定Cu,Mn的研究

报道以微晶萘作吸附载体的固相萃取分离及ＩＣＰ－ＡＥＳ测定Ｃｕ，Ｍｎ的新方法，详细研究了溶液酸度，试剂浓度，萘用量及共存离子对待测物回收率的影响，考查了加入适量的Ｃｏ＾２＋，对富集痕量Ｃｕ＾２＋Ｍｎ＾２＋辅助作用，本法用于生物样品马尾藻及小牛肝中Ｃｕ，Ｍｎ的测定，分析结果与标准值吻合。     

吐温80-盐-水体系的液-固萃取光度法测定痕量钴

研究了Ｃｏ（Ⅱ）－ＰＡＲ在吐温８０－硫酸铵体系中的最佳萃取条件,建立了生物样品中测定痕量钴的非有机溶剂液－固萃取光度法。在ｐＨ７．０～１０．５的ＮＨ３．Ｈ２Ｏ－ＮＨ４Ｃｌ缓冲溶液中,１金属配合物Ｃｏ（Ⅱ）－ＰＡＲ可被吐温８０固相富集,最大吸收波长为５１５ｎｍ,钴含量在０～５．０ｕｇ／ｍＬ范围内服从比尔定律,可用于头发、茶叶和维生素Ｂ１２针剂中痕量钴的测定。     

钴(Ⅱ)催化偶氮胭脂红B的褪色反应特性及应用

基于氢氧内介质中痕量钴对过氧化氢氧化偶氮胭脂红Ｂ的褪色反应的强烈催化作用,建立了催化光度法测定痕量钴的新方法。方法灵敏度为５．２４×１０＾－１２ｇ／ｍＬ,测定范围为０￣３５ｎｇ／１０ｍＬ,对质量浓度为３μｇ／Ｌ的Ｃｏ（Ⅱ）重复测定１１次的相对标准偏差为２．１６％。方法应用于维生素Ｂ１２和矿泉水中痕量钴的测定,结果满意。     

5-(5-氟-2-吡啶偶氮)-2,4-二氨基甲苯与钴显色反应的研究及应用

研究了新合成试剂5-(5-氟-2-吡啶偶氮)-2,4-二氨基甲苯(5-F-PADAT)与钴(Ⅱ)的显色反应。实验表明,在pH4.7~9.0范围内,钴与试剂形成紫红色配合物,其最大吸收波长位于506 nm。该配合物在无机酸作用下,可转化为另一具有较高吸收特性的质子化型体,最大吸收波长红移到565 nm,适宜的酸浓度范围分别为:0.24~3.6 mol/L HClO4、0.16~3.84 mol/L H2SO4、0.48~2.4 mol/L HCl、0.64~3.84 mol/L H3PO4。配合物表观摩尔吸光系数ε565=9.1×104L.mol-1.cm-1,钴(Ⅱ)质量浓度在0~0.5μg/mL内符合比尔定律。所拟方法已应用于维生素B12针剂中微量钴的测定。     

钴(Ⅱ)-过氧化氢-DCF 偶氮胂体系催化动力学光度法测定中草药中痕量钴

在邻苯二甲酸氢钾-氢氧化钠介质中,以钴(Ⅱ)催化过氧化氢氧化 DCF 偶氮胂的褪色反应为指示反应,建立了测定痕量钴(Ⅱ)的新方法。测定了反应级数和表面活化能。方法的检出限为 2.6×10-12 g/mL,线性范围为 0～23 ng/10mL。用于测定几种中草药样品中的钴,相对标准偏差为 2.8%～3.0%。     

分光光度法同时测定微量铁和钴

在碱性介质中,铁(Ⅱ)和钴(Ⅱ)可与硫代巴比妥酸-NO2-体系反应分别形成一种稳定的兰色和黄色配合物,铁(Ⅱ)配合物在656nm和386nm具有吸收峰,钴(Ⅱ)配合物只有一个吸收峰位于423nm,体系的吸光度A6Fe56、A4F2e3、AC42o3与铁、钴含量在一定的范围内呈良好的线性关系,且铁(Ⅱ)、钴(Ⅱ)配合物在423nm波长处的吸光度具有良好的加和性,建立了一种同时测定微量铁和钴的新的分光光度法。方法的线性范围分别为铁0～50μg/(25mL)、钴0～25μg/(25mL)。将该法应用于水样中微量铁和钴的同时测定,其结果分别与原子吸收光谱法和紫尿酸光度法相吻合,加标回收率分别为98%～102%和94%～106%,相对标准偏差(RSD)分别为1.0%～1.8%和3.1%～4.7%(n=5)。     

氯化银比浊法测定镍钴锰三元素氢氧化物中氯离子

建立了氯化银比浊法测定镍钴锰三元素氢氧化物中氯离子含量的测定方法。选择了合适的测定波长,并对硝酸用量、沉淀剂用量、稳定时间对测定结果的影响进行了试验,确定了较优的分析条件。样品加标回收率在95%~103.3%,氯离子浓度在0~4μg/mL与浊度值有良好线性关系。方法为控制镍钴锰三元素氢氧化物中氯离子提供了检测依据。     

Study of 2-(2-quinolinylazo)-5-dimethylaminobenzoic acid as a new chromogenic reagent for the spectrophotometric determination of cobalt

2-(2-Quinolinylazo)-5-dimethylaminobenzoic acid (QADMAB) is proposed as a new sensitive and selective chromogenic reagent for spectrophotometric determination of cobalt. The QADMAB reacts with cobalt in the presence of cetyl trimethylammonium bromide (CTMAB) medium to form a violet complex of molar ratio 1:2 (cobalt to QADMAB) in the pH range 3.2-5.2. The molar absorptivity of the complex is 1.28x10(5) L mol(-1) cm(-1) at 625 nm. Beer's law is obeyed in range 0.01-0.32 micro g mL(-1). The relative standard deviation for eleven replicate samples of 0.2 micro g mL(-1) is 0.76%. This method was applied to the determination of cobalt in biological samples, Vitamin B(12), alloys and water with good results.     

8-喹啉偶氮显色剂QADCB的合成及其分析性能的研究

报道了8-喹啉偶氮显色剂2-(8-喹啉偶氮)-5-二羧甲氨基苯甲酸(QADCB)的合成、提纯与鉴定,研究了其与Co(Ⅱ)、Ni(Ⅱ)、Fe(Ⅲ)的显色反应,对QADCB与Co(Ⅱ)的显色反应作了研究。在pH5.9的缓冲体系中,试剂与Co(Ⅱ)形成棕红色配合物,其最大吸收波长位于650nm,表观摩尔吸光系数为4.2×104L.mol-1.cm-1,钴量在0~20μg/25mL范围内符合比耳定律。方法简便、快速,选择性较好,已用于纯铜、维生素B12中微量钴的测定,结果满意。     

高效液相色谱法测定大鼠血浆中的原儿茶酸

建立了大鼠血浆中原儿茶酸含量测定的高效液相色谱方法。采用的色谱柱为DiamondsilTM C18 柱(150 mm×4.6 mm,5 μm);流动相为乙腈-水(体积比为9∶91,用H3PO4 调pH至2.5);流速1.2 mL/min;检测波长260 nm;内标为对羟基苯甲酸。原儿茶酸的线性范围为0.050~3.20 mg/L,线性相关系数为0.9978，最低定量限为0.050 mg/L,日内和日间测定的精密度（以相对标准偏差表示）均低于7.0%,准确度（以相对误差表示）为-1.4%～2.6%；在0.050,0.40,3.20 mg/L低、中、高3个添加浓度水平下，血浆样品的提取回收率分别为83.4%,87.3%,91.1%。该方法简便,灵敏,准确,适用于大鼠体内原儿茶酸的药物动力学研究。     

Development of an HPLC method for the determination of salidroside in beagle dog plasma after administration of salidroside injection: application to a pharmacokinetics study

A simple RP-HPLC method was established for the determination of salidroside in dog plasma. Salidroside is one of the most active ingredients of Rhodiola L. The method had within-run precision values in the range of +/- 2.3 to +/- 9.1% (n = 5) and between-run precision in the range of +/- 3.2 to +/- 9.8%. A simple protein precipitation for salidroside extraction was processed using ACN at precipitant-to-plasma volume ratio (P-P ratio) of 3:2. The extraction recoveries of salidroside at seven concentrations were higher than 63.2%. There was a linear relationship between chromatographic area and concentration over the range of 0.83-520 microg/mL for salidroside in plasma (R = 0.9926). The LOQ (S/N = 10) of the method was 0.83 microg/mL. The method was applied in a study of the pharmacokinetics of salidroside injection in six beagle dogs. The major pharmacokinetic parameters of C(max), AUC(0-24), AUC(0-infinity), and t(1/2) of salidroside in beagle dogs after i.v. administration of a single 75 mg/kg (5 mL/kg) dose were 96.16 +/- 8.59 microg/mL, 180.3 +/- 30.6 microg h/mL, 189.3 +/- 32.1 microg h/mL, and 2.006 +/- 0.615 h, respectively.     

Development of an reliable analytical method for synergistic extractive spectrophotometric determination of cobalt(II) from alloys and nano composite samples by using chromogenic chelating ligand

A synergistic simple and selective spectrophotometric method was developed for the determination of cobalt(II) with 1-(2',4'-dinitro aminophenyl)-4,4,6-trimethyl-1,4-dihydropyrimidine-2-thiol [2',4'-dinitro APTPT] as a chromogenic reagent. The proposed method has been described on the basis of synergistic effective extraction of cobalt(II) in presence of pyridine at pH range 9.5-10.2, showed orange-red coloured ternary complex having molar ratio 1:2:2 (M:L:Py). The equilibrium time is 10 min for extraction of cobalt(III) from organic phase. The absorbance of coloured organic layer in chloroform is measured spectrophotometrically at 490 nm against reagent blank. The Beer's law was obeyed in the concentration range 2.5-15 μg mL(-1) of cobalt(II) and optimum concentration range was 5-12.5 μg mL(-1) of cobalt(II) and it was evaluated from Ringbom's plot. The molar absorptivity and Sandell's sensitivity of cobalt(II)-2',4'-dinitro APTPT-pyridine complex in chloroform are 1.109×10(3) L mol(-1) cm(-1) and 0.053 μg cm(-2), respectively while molar absorptivity and Sandell's sensitivity of cobalt(II)-2',4'-dinitro APTPT complex in chloroform are 6.22×10(2) L mol(-1) cm(-1) and 0.096 μg cm(-2), respectively. The composition of cobalt(II)-2',4'-dinitro APTPT-pyridine complex (1:2:2) was established by slope ratio method, mole ratio method and Job's method of continuous variation. The ternary complex was stable for more than 48 h. The interfering effects of various cations and anions were also studied, and use of suitable masking agents enhances the selectivity of the method. The method is successfully applied for the determination of cobalt(II) in binary, synthetic mixtures and real samples. A repetition of the method was checked by finding relative standard deviation (R.S.D.) for n=5 which was 0.15%. The reliability of the method is confirmed by comparison of experimental results with atomic absorption spectrophotometer.