Preparation of Colloidosome Microcapsules Based on Particle Stabilized Photo-Crosslinkable Pickering Emulsions

研究了光敏性聚合物刷修饰二氧化硅纳米粒子的制备及其乳化行为,提供了一种制备新颖＂胶体体＂微胶囊的方法.首先,在二氧化硅纳米粒子表面引入原子转移自由基聚合（ATRP）引发剂分子,通过表面引发ATRP得到含有香豆素侧基聚合物刷光敏性的纳米二氧化硅粒子（SiO2-PMMA-PCMA）;然后,以该粒子为乳化剂制备油包水型的皮克林乳液;最后,在紫外光的照射下引发香豆素侧基的交联反应从而得到＂胶体体＂微胶囊.结果表明,香豆素单体7-（2-甲基丙烯酰乙氧基）-4-甲基香豆素（CMA）和SiO2-PMMA-PCMA在紫外光作用下都可以发生交联反应,以SiO2-PMMA-PCMA纳米粒子作乳化剂可以制备稳定的皮克林乳液,光交联后得到的＂胶体体＂微胶囊的平均粒径约为170μm.     

纳米SiO_2粒子表面静电吸附引发剂的活性研究

引发剂2,2′-偶氮二(2-脒基丙烷)二氢氯化物(AIBA)可通过静电作用而高效稳定地吸附到在弱碱性水相中均匀稳定分散的纳米SiO2粒子表面.对这些吸附引发剂的热分解行为、在纳米SiO2粒子表面原位引发甲基丙烯酸甲酯(MMA)乳液聚合的动力学和纳米SiO2粒子表面的聚合锚固情况进行了研究.发现非吸附和吸附引发剂的热分解活化能分别为148.5kJ/mol和124.5kJ/mol,70℃时半衰期分别为12.6h和5.2h,说明在相同状态下静电吸附引发剂具有比非吸附引发剂更高的活性,因而在原位乳液聚合中表现出比常规乳液聚合更短的诱导期和更高的聚合速率.更关键的是,具有较高活性的吸附引发剂高效稳定地吸附在SiO2粒子表面,可以使聚合反应总是优先发生于纳米SiO2粒子表面,从而可以更好地促进单体在纳米SiO2粒子表面的锚固,最终有效提高无机/有机相间的复合程度.     

ATRP法在纳米SiO2表面接枝PBA及其对POM的改性

本论文研究了原子转移自由基聚合法(ATRP)在纳米二氧化硅(SiO2)表面接枝聚丙烯酸丁酯(PBA)以及其对聚甲醛（POM）进行改性。红外光谱（FTIR）、透射电镜(TEM)及凝胶渗透色谱（GPC）等测试表明：采用ATRP法可制备均匀分散的SiO2-g-PBA纳米复合粒子。力学性能、扫描电子显微镜（SEM）及透射电子显微镜（TEM）等测试表明：纳米SiO2在POM中团聚明显,而SiO2-g-PBA纳米复合粒子POM中分散均匀,导致POM/SiO2-g-PBA纳米复合材料的缺口冲击强度明显高于POM及POM/SiO复合材料,当SiO2-g-PBA纳米复合粒子的质量分数为2%时,POM/SiO2-g-PBA复合材料的冲击强度是POM的8倍多,同时拉伸强度有一定的增加。     

超声波引发分散聚合反应包覆无机粒子的研究

首先在超声波场中用表面活性剂对纳米SiO₂粒子进行亲油化处理, 然后在氮气保护下利用超声波的分散、粉碎、活化、引发等多重作用, 在实现纳米SiO₂在反应介质中纳米分散的同时, 引发苯乙烯单体在纳米SiO2表面进行分散聚合反应, 制备出了SiO₂/PS(二氧化硅/聚苯乙烯)复合粒子, 运用SEM, TEM, XPS, FTIR, TGA, DSC等测试手段对复合粒子进行了表征.     

二氧化硅纳米粒子表面修饰及其表征

采用溶胶-凝胶法合成粒径在50—150nm范围内的二氧化硅（SiO2）纳米粒子。用甲基丙烯酸-3-（三甲氧基硅基）丙酯（MPS）对SiO2纳米粒子表面进行修饰，使其表面接枝能参与自由基聚合反应的碳碳双键基团。用元素分析、FTIR、^13C CP／MASNMR和^29Si CP／MASNMR等手段对修饰过的SiO2纳米粒子进行表征，以确证MPS接枝在SiO2纳米粒子上。分析修饰过的SiO2纳米粒子的^29Si CP／MASNMR和FTIR谱图，还可初步推断MPS接枝在SiO2纳米粒子表面的机理：MPS首先发生水解缩合反应形成低聚物，然后通过氢键作用吸附到SiO2纳米粒子表面，最后MPS低聚物中未缩合的硅羟基与SiO2纳米粒子表面的硅羟基发生缩合反应。     

SiO2表面RAFT接枝聚合苯乙烯

基于纳米SiO2表面羟基与7-甲基丙烯酰氧基丙基三甲氧基硅烷间的偶联反应,在纳米SiO2表面引入可聚合双键。采用可逆加成断裂链转移（RAFT）聚合技术,以偶氮二异丁腈为引发剂,使SiO2表面接枝聚合苯乙烯。考察了二硫代苯甲酸异丁腈酯、二硫代苯甲酸苄酯、（1,2,4-三氮唑）基二硫代甲酸苄酯和二硫代新戊酸苄酯等对SiO2表面接枝聚合苯乙烯速率的影响。结果表明,SiO2表面接枝聚合苯乙烯的速率决定于RAFT试剂的Z基团结构。二硫代新戊酸苄酯调控的SiO2表面接枝聚合苯乙烯的速率最高。     

纳米SiO_2锚固光敏基团引发MMA光接枝聚合研究

对纳米SiO2进行了锚固光引发剂的表面修饰,进而引发甲基丙烯酸甲脂(MMA)光接枝聚合制备有机/无机复合粒子.纳米SiO2粒子首先用氯化亚砜进行表面氯化,再与光引发剂2-羟基-4-(2-羟基乙氧基)-2-甲基苯丙酮(Irgacure2959)反应从而锚固上光引发剂.通过紫外光引发MMA在经过修饰过的纳米SiO2表面上进行表面光接枝聚合.采用IR、TGA和TEM等方法表征了接枝前后纳米粒子的变化,证明了表面接枝物的存在,并研究了不同反应条件对单体转化率、接枝率和接枝效率的影响.研究结果表明,搅拌对接枝过程的影响比较显著.TGA结果显示未搅拌聚合时接枝率只能达到比较小的程度,而在搅拌条件下180min内MMA的接枝率可达到110%.     

单分散PS/SiO_2纳米复合微球的制备与表征

采用一种简单和低成本的方法制备单分散SiO2包覆聚苯乙烯(PS)(PS/SiO2)核-壳型纳米复合微球.首先在聚乙烯吡咯烷酮(PVP)存在下制备了PS纳米微球,然后在NH4OH/乙醇溶液中通过溶胶-凝胶过程在PS微球表面包覆SiO2.PS纳米微球的制备在水介质中进行,无需使用共单体,使用的是常用的过硫酸钾自由基引发剂;包覆处理前不用进行溶剂交换或离心处理.研究了PVP,NH4OH和原硅酸乙酯(TEOS)的用量对PS/SiO2纳米复合微球尺寸和形态的影响.随着PVP用量增加,PS微球变小,因此得到较小的PS/SiO2纳米复合微球;NH4OH用量对SiO2包覆层的厚度没有影响,但对SiO2包覆层的表面形态有影响,随着NH4OH用量增加包覆层表面变得粗糙;随着TEOS溶液用量增加,生成的SiO2增加,其包覆层的厚度增加.     

原位聚合法制备纳米二氧化硅/聚氨酯复合树脂

采用高压剪切分散（HPSH）的方法先将纳米SiO2分散在合成聚氨酯原料中,再应用原位聚合的方法制备了纳米SiO2/聚氨酯复合树脂。 用热重分析、动态机械热分析（DMTA）和扫描电子显微镜等测试技术研究了纳米SiO2的用量及其分散方法对聚氨酯树脂的热稳定和力学性能的影响。 结果表明,二苯甲基二异氰酸酯（MDI）中的-NCO和纳米SiO2表面的-OH发生了化学反应,SiO2表面的包覆率约为7%;通过高压剪切分散的方法能够使纳米SiO2在聚氨酯基体中均匀的分散开来,粒径为30~40 nm,而超声处理的纳米SiO2会聚集约为200 nm聚集体。 当SiO2的添加质量分数为3%时复合树脂（HPSH处理SiO2）的拉伸强度和断裂伸长率均达到最大值,分别为84.3 MPa和438.7%。 此外,与纯树脂相比,复合树脂(4%纳米SiO2)的Tg、Td和T-50%分别增加了17.2、9和21 ℃。     

纳米SiO_2粒子锚固偶氮引发剂及接枝聚甲基丙烯酸甲酯

对纳米SiO2 粒子锚固偶氮引发剂 ,进而引发甲基丙烯酸甲酯聚合而制备聚甲基丙烯酸甲酯(PMMA) 纳米SiO2 复合粒子进行了研究 .纳米SiO2 先用环氧型硅烷偶联剂处理 ,再与偶氮二氰基戊酸发生缩合反应而锚固上偶氮引发剂 ,通过差示扫描量热和元素分析证明了引发剂在纳米SiO2 表面的锚固 .通过改性纳米SiO2 存在下MMA的乳液聚合 ,制备得到了接枝率为 2 3 2 %、接枝效率为 36 1%的PMMA 纳米SiO2 复合粒子 .经乳液聚合后 ,纳米SiO2 粒子团聚程度减小 ,在水相中分散稳定 .     

单分散聚合物微球稳定Pickering乳液法制备大粒径微胶囊相变材料

采用二步加料的分散聚合法制备单分散聚甲基丙烯酸缩水甘油酯(PGMA)微球, 并使其水解, 得到水包油(O/W)型Pickering乳液稳定剂. 在Pickering乳液聚合过程中, 利用相分离机制, 形成了聚苯乙烯(PSt)和 PGMA复合为整体囊壳的微胶囊相变材料. 微胶囊平均粒径达76 μm, 囊芯含量高达83%, 相变焓达到174 J/g, 具有很高的储热容量.     

Pickering乳滴模板法制备超粒子结构有机/无机杂化微球

Pickering乳滴模板法制备有机/无机杂化的核壳微球越来越引起人们的关注,主要因为该方法制备出的微球具有以无机粒子为壳层的超粒子结构(supracolloidal structure),能够赋予微球独特的功能.胶体粒子在乳滴表面自组装形成有序的球面胶体壳,得到稳定Pickering乳液,固定乳滴表面的胶体粒子来制备核壳结构的微球或者以胶体粒子为壳层的微胶囊(colloidosome).本文综述了我们课题组以Pickering乳滴模板法制备超粒子结构有机/无机杂化微胶囊包括实心微球方面的工作.我们选择具有不同性能、种类的胶体粒子以及具有不同性质和功能的核材料,采用Pickering乳滴模板法,对吸附在乳滴表面的胶体粒子用不同的固定方法制备具有不同结构和性能的微球和微胶囊,利用基于多重Pickering乳液的聚合技术制备双纳米复合的超粒子结构多核聚合物微球.     

基于纳米氢氧化镁稳定的Pickering乳液悬浮聚合制备盔甲结构聚苯乙烯@氢氧化镁复合微球

以苯乙烯为单体、 偶氮二异丁腈(AIBN)为引发剂、 片状纳米氢氧化镁(MH)为Pickering稳定剂, 采用悬浮聚合法制备盔甲结构的聚苯烯@氢氧化镁(PS@MH)复合微球. 采用扫描电子显微镜(SEM)、 能谱分析(EDS)、 傅里叶变换红外光谱(FTIR)、 X射线衍射(XRD)、 热失重分析(TGA)和微型燃烧量热分析(MCC)等对PS@MH复合微球进行表征, 确认了其形貌和结构: 纳米氢氧化镁紧密包覆在聚苯乙烯微球表面, 形成了以纳米氢氧化镁为外层、 聚苯乙烯为内球的盔甲结构复合微球; 同时证明了具有盔甲结构的PS@MH复合微球能降低热释放速率, 抑制聚合物的降解. 该方法操作简单, 成本低廉, 制得的盔甲结构PS@MH复合微球粒径尺寸小、 分布窄, 球形度较高.     

Hollow microspheres with covalent‐bonded colloidal and polymeric shell by Pickering emulsion polymerization

Hollow microspheres with SiO₂/polymer binary shell were fabricated from Pickering emulsion stabilized solely by methacryloxypropyltrimethoxysilane‐modified SiO₂ particles, and were characterized by optical microscopy, scanning electron microscopy, Fourier transformation infrared spectrum, thermogravimetric analysis (TGA), and energy dispersive X‐ray spectroscopy. The microspheres were templated by the Pickering droplets and the inner structure was affect by the proportion of crosslinking reagent. TGA result indicated that 60.3% of polymer in the shell was connected with SiO₂ by covalent bond which was formed by copolymerization of styrene and the reactive C?C group on SiO₂ stabilizer. Copyright © 2011 John Wiley & Sons, Ltd.     

Study of emulsion polymerization stabilized by amphiphilic polymer nanoparticles

Submicron-sized polystyrene (PS) microspheres with a relatively narrow particle size distribution can be easily produced through emulsion polymerization induced by γ-ray at room temperature using a new type of amphiphilic cross-linked poly(stearyl methacrylate-co-acrylamide-co-acrylic acid) particles as stabilizer. The properties of these amphiphilic particles were described, including morphology, size, ζ potential, and contact angles. The effect of the pH value and the content of amphiphilic particles on the formation and stability of emulsions were also investigated. Meanwhile, the obtained PS microspheres were characterized by Fourier transform infrared spectroscopy, transmission electron microscopy, scanning electron microscopy and X-ray photoelectron spectroscopy. In addition, through observing the morphology and size of emulsion droplets at different times under an optical microscope, we found it is interesting that Pickering emulsions formed initially disappeared gradually, which is different from the common Pickering emulsions stabilized by inorganic particles. Thus, the mechanism was further discussed.     

Fabrication of macroporous foam and microspheres of polystyrene by Pickering emulsion polymerization

Poly(styrene-co-methacrylic acid) (PS-co-MAA) particles were synthesized via surfactant-free emulsion polymerization and then used as particulate emulsifiers for preparation of Pickering emulsions. Our results showed that adjusting the solution pH can tune the wettability of PS-co-MAA particles to stabilize either water-in-oil (W/O) or oil-in-water (O/W) Pickering emulsions. Stable W/O emulsions were obtained with PS-co-MAA particles at low pH values due to their better affinity to the dispersed oil phase. In contrast, increasing the pH value significantly changed the stabilizing behavior of the PS-co-MAA particles, leading to the phase inversion and formation of stable O/W emulsions. We found that the oil/water ratio had a significant influence on pH value of the phase inversion. It decreased with decreasing the oil/water ratio, and no phase inversion occurred when the styrene volume fraction reduced to 10 %. Additionally, macroporous polystyrene (PS) foam and PS microspheres were obtained via polymerization of Pickering high internal phase emulsion (Pickering HIPE) and O/W Pickering emulsion, respectively.     

Novel Janus Cu2(OH)2CO3/CuS microspheres prepared via a Pickering emulsion route

Janus Cu2(OH)2CO3/CuS microspheres were prepared via a Pickering emulsion route for the first time. By treating the Janus Cu2(OH)2CO3/CuS microspheres with dilute hydrochloric acid, ringent Cu2(OH)2CO3/CuS core/shell microspheres and ringent CuS shells were obtained. The hatch size of the ringent CuS shells increased with the increase of the hydrophobicity of the precursor Cu2(OH)2CO3 microspheres. Scanning electron microscopy, X-ray diffraction, energy dispersion spectra, and particle size analysis were used to characterize the products thus formed.     

Molecular imprinting in Pickering emulsions: a new insight into molecular recognition in water

Molecularly imprinted polymer microspheres were synthesized by Pickering emulsion polymerization. Fluorescence spectroscopic investigations provided insights into the template recognition in water.     

具有二氧化碳响应性的纳米球形聚电解质刷的制备及其乳化性能

以聚苯乙烯(PS)纳米球为核,利用紫外光引发聚甲基丙烯酸N,N-二甲基氨基乙酯(PDMAEMA)接枝到PS纳米球上,得到对CO_2有刺激响应的聚甲基丙烯酸N,N-二甲基氨基乙酯刷(PS-PDMAEMA)。动态光散射(DLS)、电导率结果表明PS-PDMAMEA具有CO_2刺激响应性。该微粒可以作为Pickering乳液的乳化剂,通过导入CO_2或N_2作为开关,进而破坏或稳定Pickering乳液。用数码照片、偏光显微镜等方法表征了乳液的稳定情况。结果表明:PS-PDMAEMA具有很好的CO_2刺激响应性,利用PS-PDMAEMA作为乳化剂稳定Pickering乳液,仅仅依靠气体开关(CO_2或N_2)就可改变乳液的稳定性。     

Fabrication of macroporous polystyrene/graphene oxide composite monolith and its adsorption property for tetracycline

Macroporous polystyrene microsphere/graphene oxide(PS/GO) composite monolith was first prepared using Pickering emulsion droplets as the soft template. The Pickering emulsion was stabilized by PS/GO composite particles in-situ formed in an acidic water phase. With the evaporation of water and the oil phase(octane), the Pickering emulsion droplets agglomerated and combined with each other, forming a three-dimensional macroporous PS/GO composite matrix with excellent mechanical strength. The size of the macrospores ranged from 4 mm to 20 mm. The macroporous PS/GO composite monolith exhibited high adsorption capacity for tetracycline(TC) in an aqueous solution at p H 4–6. The maximum adsorption capacity reached 197.9 mg g 1at p H 6. The adsorption behaviour of TC fitted well with the Langmuir model and pseudo-second-order kinetic model. This work offers a simple and efficient approach to fabricate macroporous GO-based monolith with high strength and adsorption ability for organic pollutants.