以硅溶胶和三氢化钛为原料合成Ti—MCM—41分子筛Ⅰ.Ti—MCM—41分子筛的合成

以硅溶胶和TiCI3水溶液为原料，采用水热合成方法制备了结晶度和长程有序性较高的中孔Ti-MCM-41分子筛。钛的加入提高了中孔分子筛的长程有序性。辅助模板剂的选择对分子筛的合成很重要，其中以四甲基氢氧化铵和四乙基氢氧化铵作辅助模板剂的效果较好。四甲基氢氧化铵的用量对分子筛的结晶度和长程有序性也有影响，用量过高和过低都会 降低分子筛的结晶度。合成的分子筛中的钛含量（摩尔分数）可以达到3．75％，进一步增加钛的含量，将不能合成得到中孔结构的分子筛。     

以硅胶和三氯化钛为原料合成Ti-MCM-41分子筛 Ⅱ. Ti-MCM-41分子筛的表征

 利用N2吸附,TG－DTA,FT－IR,UV－Vis和UV－Raman光谱等技术对以硅溶胶和TiCl3水溶液为原料合成的中孔Ti－MCM－41分子筛的孔结构和钛的配位状态进行了详细的表征．N2吸附等温线表明,Ti－MCM－41分子筛的孔径比纯硅MCM－41分子筛小,钛的加入使分子筛的单胞体积大大增加,比表面积和孔壁厚度也显著增大．TG－DTA结果表明,Ti－MCM－41分子筛中存在着两种不同的模板剂键合位．FT－IR,UV－Vis及UV－Raman光谱表明,Ti原子存在于分子筛骨架中且以四面体方式配位,没有结晶状态的TiO2形成．     

以硅胶和三氯化钛为原料合成Ti-MCM-41分子筛 Ⅲ. Ti-MCM-41分子筛的催化活性

 考察了以硅溶胶和TiCl3水溶液为原料合成的含钛中孔分子筛Ti－MCM－41对苯乙烯,α－甲基苯乙烯和环己烯氧化反应的催化性能．结果表明,对于CC双键位于端部的苯乙烯和α－甲基苯乙烯,发生的主要反应是CC双键的氧化断裂,而对于CC双键位于中间的环己烯,发生的主要反应是环氧化反应．     

Ti-HMS分子筛的合成与表征

 以十二胺(DDA)为模板剂,采用室温晶化合成了钛硅中孔分子筛Ti-HMS,并用XRD,IR,UV-Vis和N2吸附对分子筛样品进行了表征,考察了配料硅/钛比、模板剂用量及晶化时间对合成分子筛的影响. 结果表明,Ti-HMS分子筛具有较大的比表面,孔径约为3 nm. 随着配料硅/钛比的降低,Ti-HMS分子筛的比表面积减小,进入骨架的钛量增多,且非骨架钛也增多. n(DDA)/n(SiO2)≤0.22时,随着模板剂用量的减少,Ti-HMS分子筛的结晶度下降,骨架钛含量减少,非骨架钛含量增加. 晶化时间在9~18 h最佳.     

氨水介质中含Ti的MCM-41介孔分子筛的合成

 在氨水介质中采用TiCl3和正硅酸乙酯合成了含Ti量不同的MCM-41介孔分子筛. 该方法可避免使用昂贵的辅助模板剂,也不需要加入醇来调节水解速度,因而合成过程相对简单、易于控制. 采用XRD和N2吸附-脱附等技术对介孔分子筛的结构进行了表征. 结果表明,合成的MCM-41介孔分子筛的六方介孔有序性好,结晶度高. UV-Vis光谱表明,Ti-MCM-41在200～300 nm间出现了四个清晰可辨的吸收峰,说明Ti原子以多种状态存在于介孔分子筛骨架中.     

SAPO—5分子筛的合成与表征

SAPO-5分子筛合成所用的模板剂主要是四丙基氢氧化铵、三乙胺和三丙胺等。目前报道较多的是四丙基氢氧化铵和三乙胺。尚未见以三丙胺(Pr_3N)为模板剂在F~-离子存在下合成SAPO-5分子筛的详细报道。此外,对SAPO-5分子筛合成影响因素的研究还不够系统。本文以三丙胺为模板剂,在F~-离子存在下,合成出SAPO-5分子筛,用多种研究手段进行了鉴定,并对影响合成的诸因素进行了研究和讨论。     

用氟化氢－三乙胺复合模板剂合成SAPO－34分子筛

 采用X射线衍射、扫描电镜、氨吸附红外光谱及核磁共振等表征手段，研究了以氟化氢－三乙胺为复合模板剂合成的SAPO－34分子筛．结果表明，相对于用三乙胺模板剂合成的样品，用氟化氢－三乙胺复合模板剂合成的样品结晶度高，晶粒小，分子筛的酸量低，骨架中硅结构单一，比表面积和孔体积较大．以氟化氢－三乙胺复合模板剂合成的分子筛，在催化甲醇制低碳烯烃反应中结焦速率降低，生成乙烯及丙烯的选择性则略有提高．     

合成TS-1分子筛的结晶动力学及催化性能研究

 以自制的四丙基氢氧化铵为模板剂，通过改进经典的水热晶化操作步骤，快速合成出TS－1分子筛，并对其合成过程进行了结晶动力学研究．结果表明，在所考察的晶化温度下，TS－1的成核诱导期均很短，且晶体的成核及生长速率随晶化温度的升高而增大；其表观成核活化能和表观生长活化能分别为33．60和36．73kJ／mol，比经典的水热合成体系所得数值略小．晶化温度越高，晶化液的pH值变化越显著；分子筛结构的迅速形成与晶化液pH值的快速上升过程相一致．高温下合成的TS－1分子筛对苯酚羟基化反应的催化活性更高．导致TS－1分子筛催化活性差异的主要原因是进入分子筛骨架中钛的含量不同，以及样品的结晶度不同．在不同晶化温度下所合成的TS－1分子筛颗粒尺寸稍有差别，但均为100nm左右．     

以催化油浆窄馏分为添加剂的Al－MCM－41分子筛的合成

 采用阳离子表面活性剂十六烷基三甲基溴化铵为模板剂，以正硅酸乙酯为硅源，以硫酸铝为铝源，水热合成了以催化油浆窄馏分为添加剂的高比表面积Al－MCM－41介孔分子筛，并利用XRD，HREM，TG－DTA及N2吸附－脱附等测试手段对合成样品进行了表征．合成的Al－MCM－41分子筛的比表面积和孔体积分别达到1295m2／g和1．5cm3／g，其平均孔径为4．3nm．重点研究了Al－MCM－41分子筛结晶度、晶胞参数、比表面积、孔体积及平均孔径等结构性质随催化油浆窄馏分添加量及其组成的变化规律，并从合成机理上进行了解释．     

TS—2钛硅分子筛合成原料和方法的改进

以硅溶胶为硅源,钛酸四丁酯为钛源,四丁基氢氧化铵（ＴＢＡＯＨ）为模板剂,采用改进的方法合成了高结晶度的ＴＳ－２分子筛,并对所合成样品用ＦＴ－ＩＲ,ＸＲＤ,ＳＥＭ,＾２９Ｓｉ ＭＡＳ ＮＭＲ,ＩＣＰ和Ｎ２吸附等方法进行了结构表征。实验中发现原料内添加适量氨水可使产品晶粒减小,骨架钛含量增加,比表面积和孔容增大,有利于提高其催化活性。另外,将晶化后母液中的ＴＢＡＯＨ循环使用,也能得到结晶度和催化性能良     

Detection of NADH and Ethanol at Titanium Containing MCM‐41 with Low Overpotential

Titanium‐containing MCM‐41 (Ti‐MCM‐41) modified glassy carbon electrode (GCE) can exhibit an excellent electrocatalytic activity towards the oxidation of β‐Nicotinamide adenine dinucleotide (NADH). A dramatic decrease in the overvoltage of NADH oxidation reaction is observed at 0.28 V vs. SCE. The application in the amperometric biosensing of ethanol using alcohol dehydrogenase enzyme (ADH) also has been demonstrated with this material. The proposed sensor shows a highly sensitivity, an acceptable reproducibility and a good stability. The linear range of ethanol is 25–1000 μM and the detection limit is 8.0 μM. Ti‐MCM‐41 modified electrode not only can be used to detect the concentration of NADH in biochemical reaction, but also as the potential matrix for the construction of dehydrogenases sensor.     

Low Potential Detection of NADH at Titanium‐Containing MCM‐41 Modified Glassy Carbon Electrode

Titanium‐containing MCM‐41 (Ti‐MCM‐41) modified glassy carbon electrode (GCE) can exhibit an excellent electrocatalytic activity towards the oxidation of β‐Nicotinamide adenine dinucleotide (NADH). A dramatic decrease in the over‐voltage of NADH oxidation reaction is observed at 0.28 V (vs. SCE). The modified electrode is found to be stable and reproducible. The electrode shows a linear response for a wide range of 10–1200 μM NADH and the detection limit is 8.0 μM. Ti‐MCM‐41 mesoporous molecular sieves provide an efficient matrix for development of NADH biosensors and the prepared electrode not only can be used to detect the concentration of NADH in biochemical reaction, but also as the potential matrix of the construction of dehydrogenases biosensor.     

Ti—MCM—41的结构特征与芳烃羟化反应的化学亲和选择性

以不同硅源合成了Si/Ti比不同的Si-Ti－MCM－41,并在引入Ti的同时引入Al,合成了Si/Al比不同的Si-Ti-Al-MCM-41。XRD、TEM、低温N2吸附的表征结果说明,Ti-MCM-41具有长程有序一维孔道,且比表面积较高,FT－IR光谱表征说明,Ti对骨架Si的取代使MCM－41表面出现缺陷羟基。Al的引入有利于Ti-MCM-41有序结构的形成。且可调变Ti-MCM-41的表面性质。Ti-MCM-41在不同极性芳烃化合物的羟化过程中表现出化学亲和选择性,且调变Ti-MCM-41的表面性质可实现对化学亲和选择性的控制。     

Ti-MCM-41催化剂的表面性质及介质极性对

用不同的铝源改性Ti MCM 41催化剂 ,得到了具有长程有序结构、n(Si) /n(Ti) =2 5的不同Si/Al比的改性Ti MCM 41.通过研究芳烃羟化反应随催化剂表面性质的变化规律发现 ,调变催化剂的表面性质 ,可控制反应物苯及目的产物苯酚与Al Ti MCM 41催化活性中心接近的程度 ,从而可实现对芳烃羟化反应化学选择性的控制 .介质极性对芳烃的化学亲和选择性也有影响 ,只有富含供电子氧原子且其极性大于苯的介质才有利于芳烃的羟化反应     

Synthesis of Ti‐MCM‐41 directly from silatrane and titanium glycolate and its catalytic activity1

Titanium is successfully incorporated in hexagonal mesoporous silica to form Ti‐MCM41 at low temperature. Silatrane and titanium glycolate synthesized from the oxide one‐pot synthesis process are used as the precursors. Using the cationic surfactant cetyltrimethylammonium bromide as a template, the resulting meso‐structure mimics the liquid‐crystal phase. The percentage of titanium loading is varied in the range 1–35%. The temperatures used in the preparation are 60 °C and 80 °C. After heat treatment, very high surface area mesoporous silica was obtained and characterized using diffuse reflectance UV (DRUV) spectroscopy, X‐ray diffraction (XRD), BET surface area, X‐ray fluorescence, energy dispersive spectroscopy and transmission electron microscopy (TEM). At 35% titanium, the titanium atom is also in the framework showing the pattern of hexagonal mesostructure, as shown by DRUV, XRD and TEM results. The surface area is extraordinarily high, up to more than 2300 m² g^?1, and the pore volume is as high as 1.3 cm³ g^?1 for a titanium loading range of 1–5%. Oxidative bromination reaction using Ti‐MCM‐41 as catalyst showed impressive results, with the 60 °C catalysts having higher activity. Copyright © 2005 John Wiley & Sons, Ltd.     

MSU-SMFI和MCM-41的催化裂化及烷基化活性比较

以MFI沸石前驱体作为基本结构单元组装介孔硅铝分子筛MSU-S_MFI. XRD和氮气吸附数据表明MSU-SMFI具有类似MCM-41的六方排列介孔孔道结构,而且其织构参数和以传统方法合成的含铝MCM-41也大体相当.NH₃-TPD显示由沸石前驱体组装的MSU-S_MFI较硅铝比相同的含铝MCM-41介孔分子筛的固体酸量显著提高.MSU-S_MFI上的异丙苯催化裂化转化率比含铝MCM-41提高31％, 1,3,5-三异丙苯在MSU-S_MFI上也发生了更深的裂解. MSU-S_MFI上萘的叔丁基化的转化率比含铝MCM-41提高了15％.以沸石前驱体作为基本结构单元是提高介孔分子筛固体酸性的有效方法.     

Photovoltaic activity of Ti/MCM‐41

Ti/MCM‐41 is a well‐known heterogeneous catalyst for alkene epoxidation with organic peroxides. This titanosilicate contains isolated titanium atoms forming part of a framework of mesoporous silica whose structure is formed by parallel hexagonal channels 3.2 nm in diameter. The surface area and porosity of Ti/MCM‐41 are about 880 m² g^?1 and 0.70 cm³ g^?1, respectively. These values are among the highest for any material. Herein, we show that Ti/MCM‐41 exhibits photovoltaic activity. Dye‐sensitized solar cells using mesoporous Ti/MCM‐41 (2.8–5.7 % Ti content) as active layer, black dye N3 as photosensitizer and I₃^?/I^? in methoxyacetonitrile as electrolyte exhibit a V_OC, J_SC and FF of 0.44 V, 0.045 mA cm^?2 and 0.33, respectively. These values compare well against 0.75 V, 4.1 mA cm^?2 and 0.64, respectively, measured for analogous solar cells using conventional P‐25 TiO₂. However, the specific current density (J_SC/Ti atom) for the Ti/MCM‐41 is very similar to that of P25 TiO₂.     

新型MCM-41-β-沸石中孔-微孔复合分子筛

ＭＣＭ－４１是１９９２年由Ｍｏｂｉｌ公司首次合成,具有可调的规整孔道结构,孔径大小为１．６～１０ｎｍ的六方中孔分子筛［１,２］,β－沸石是具有三维十二元环孔道,一条线性通道孔径为０．５７ｎｍ×０．７５ｎｍ,另一条由两种线性通道相交形成的弯曲通道,孔径...     

含钛CDS-1分子筛的水热合成与表征

以钛酸正丁酯（TBOT）为钛源、以发烟硅胶为硅源、以四甲基氢氧化铵（TMAOH）为模板剂,采用了一步法直接水热合成了CDO晶体结构的含钛分子筛,Ti-CDS-1。用粉末X-射线衍射、电子扫描、紫外可见漫反射光谱,傅立叶变换红外光谱等手段对所合成的样品进行了表征,结果表明,Ti-CDS-1维持原来全硅分子筛的片状晶体外形;原料中钛原子大部分嵌入到CDS-1分子筛分子筛骨架,少量钛在分子筛表面形成八面体非骨架钛物种,这部分骨架外钛可以用酸处理选择性去除。     

Synthesis,Characterization and Catalysis of Ce‐MCM‐41

The cerium‐containing MCM‐41 (Ce‐MCM‐41) has been synthesized by direct hydrothermal method. The low‐angle XRD patterns revealed the typical five major peaks of MCM‐41 type hexagonal structures. The interplanar spacing d₁₀₀ = 38.4 Å was obtained that can be indexed on a hexagonal unit cell parameter with a_o = 44.3 Å which was larger than that of pure siliceous MCM‐41 (Si‐MCM‐41). Transmission electron micrograph shows the regular hexagonal array of uniform channel characteristics of MCM‐41. The BET surface area of Ce‐MCM‐41 was 840 m²/g, which is much reduced as compared to that of Si‐MCM‐41, with the pore size of 26.9 Å and mesopore volume of 0.78 cm³/g were measured by nitrogen adsorption‐desorption isotherm at 77 K. Along with the results, the synthesized Ce‐MCM‐41 exhibited a well‐ordered MCM‐41‐type mesoporous structure with the incorporation of cerium. Using Ce‐MCM‐41 as a support, the Rh (0.5 wt%) catalyst exhibited very high activity for the NO/CO reactions.