以吡啶为原料制备氮掺杂碳纳米管

在700～800 ℃,以吡啶为原料用CVD方法制备出了管径在20～40 nm的竹节状碳纳米管. EDX和XPS结果都表明氮掺杂到碳纳米管中. HRTEM研究发现掺氮碳纳米管的竹节由数层石墨片弯曲而成,纳米管外层石墨层逐渐消失.从Raman谱图的对照中发现,与相似条件下制备出的纯碳纳米管相比,氮掺杂碳纳米管的D谱带对G谱带的相对强度增加, TGA研究发现掺杂纳米管在较低温度下即被氧化,这些结果都说明氮掺杂使得纳米管的缺陷增加.     

硫掺杂钛酸(盐)纳米管的表征与可见光光催化活性

以二硫化钛为钛源和硫源,通过与NaOH水热反应成功制备了硫掺杂钛酸(盐)纳米管。 采用X射线衍射、高分辨透射电子显微镜、扫描电子显微镜、扩展X射线吸收精细结构(EXAFS)和X光微区分析等手段对所制备的硫掺杂钛酸(盐)纳米管的结构、形貌、硫掺杂状态和掺杂量进行了表征,并以可见光光催化氧化乙醇反应为探针,采用原位气相色谱技术研究了硫掺杂钛酸纳米管的可见光光催化活性;结果表明,S原子以S2-形式取代了钛酸纳米管骨架中O原子的位置, 有效实现了硫掺杂;硫掺杂钛酸(盐)纳米管壁厚平均尺寸为2.9 nm,管径平均尺寸为9.7 nm。 可见光光催化氧化乙醇反应结果表明,掺硫钛酸纳米管在极低的掺硫量条件下,表现出比未掺杂的二氧化钛纳米管具有更高的可见光光催化活性。     

N掺杂TiO_2纳米管阵列的制备及可见光光催化性能研究

分别以氨水、乙二胺、丁胺为氮源,利用阳极氧化法和湿化学法合成氮掺杂的二氧化钛(TiO2)纳米管阵列.通过扫描电镜(SEM)、X射线衍射(XRD)、X射线光电子能谱(XPS)等表征方法对氮掺杂TiO2纳米管形貌,晶型和氮元素掺杂方式进行分析,并通过可见光光催化降解六氯苯(HCB)废水,研究氮元素掺杂方式与可见光光催化活性的关系.结果表明有序排列的TiO2纳米管阵列垂直生长在钛基底表面,管长500nm左右,管径100nm左右.氮元素掺杂阻碍了TiO2晶粒的增长,抑制了锐钛矿向金红石相的转变.无机氮比有机氮更加利于氮元素进入TiO2晶格,取代态氮比间隙态氮表现出更高的可见光光催化活性.     

N-TiO2/ZnO复合纳米管阵列的掺杂机理及其光催化活性

以ZnO纳米柱阵列为模板, 采用溶胶-凝胶法制备出TiO2/ZnO和N掺杂TiO2/ZnO的复合纳米管阵列. 扫描电镜(SEM)、X射线光电子能谱(XPS)和紫外-可见漫反射吸收光谱(UV-Vis)的结果表明: 两种阵列的纳米管均为六角形结构, 直径约为100 nm, 壁厚约为20 nm; 在N-TiO2/ZnO复合纳米管阵列中, 掺入的N离子主要是以N-Ox、N-C和N-N的形式化学吸附在纳米管表面, 仅有少量的N离子以取代式掺杂的方式占据TiO2晶格O的位置; 表面N物种形成的表面态能级和取代式掺杂导致带隙的窄化, 增强了纳米管阵列的光吸收效率, 促进了光生载流子的分离. 光催化实验结果表明, N离子的掺杂有利于N-TiO2/ZnO复合纳米管阵列光催化活性的提高.     

N-TiO2/ZnO复合纳米管阵列的掺杂机理及其光催化活性

以ZnO纳米柱阵列为模板, 采用溶胶-凝胶法制备出TiO2/ZnO和N掺杂TiO2/ZnO的复合纳米管阵列. 扫描电镜(SEM)、X射线光电子能谱(XPS)和紫外-可见漫反射吸收光谱(UV-Vis)的结果表明: 两种阵列的纳米管均为六角形结构, 直径约为100 nm, 壁厚约为20 nm; 在N-TiO2/ZnO复合纳米管阵列中, 掺入的N离子主要是以N-Ox、N-C和N-N的形式化学吸附在纳米管表面, 仅有少量的N离子以取代式掺杂的方式占据TiO2晶格O的位置; 表面N物种形成的表面态能级和取代式掺杂导致带隙的窄化, 增强了纳米管阵列的光吸收效率, 促进了光生载流子的分离. 光催化实验结果表明, N离子的掺杂有利于N-TiO2/ZnO复合纳米管阵列光催化活性的提高.     

N-TiO2/ZnO复合纳米管阵列的掺杂机理及其光催化活性

以ZnO纳米柱阵列为模板, 采用溶胶-凝胶法制备出TiO2/ZnO和N掺杂TiO2/ZnO的复合纳米管阵列. 扫描电镜(SEM)、X射线光电子能谱(XPS)和紫外-可见漫反射吸收光谱(UV-Vis)的结果表明: 两种阵列的纳米管均为六角形结构, 直径约为100 nm, 壁厚约为20 nm; 在N-TiO2/ZnO复合纳米管阵列中, 掺入的N离子主要是以N-Ox、N-C和N-N的形式化学吸附在纳米管表面, 仅有少量的N离子以取代式掺杂的方式占据TiO2晶格O的位置; 表面N物种形成的表面态能级和取代式掺杂导致带隙的窄化, 增强了纳米管阵列的光吸收效率, 促进了光生载流子的分离. 光催化实验结果表明, N离子的掺杂有利于N-TiO2/ZnO复合纳米管阵列光催化活性的提高.     

N-TiO2/ZnO复合纳米管阵列的掺杂机理及其光催化活性

以ZnO纳米柱阵列为模板, 采用溶胶-凝胶法制备出TiO2/ZnO和N掺杂TiO2/ZnO的复合纳米管阵列. 扫描电镜(SEM)、X射线光电子能谱(XPS)和紫外-可见漫反射吸收光谱(UV-Vis)的结果表明: 两种阵列的纳米管均为六角形结构, 直径约为100 nm, 壁厚约为20 nm; 在N-TiO2/ZnO复合纳米管阵列中, 掺入的N离子主要是以N-Ox、N-C和N-N的形式化学吸附在纳米管表面, 仅有少量的N离子以取代式掺杂的方式占据TiO2晶格O的位置; 表面N物种形成的表面态能级和取代式掺杂导致带隙的窄化, 增强了纳米管阵列的光吸收效率, 促进了光生载流子的分离. 光催化实验结果表明, N离子的掺杂有利于N-TiO2/ZnO复合纳米管阵列光催化活性的提高.     

N-TiO2/ZnO复合纳米管阵列的掺杂机理及其光催化活性

以ZnO纳米柱阵列为模板, 采用溶胶-凝胶法制备出TiO2/ZnO和N掺杂TiO2/ZnO的复合纳米管阵列. 扫描电镜(SEM)、X射线光电子能谱(XPS)和紫外-可见漫反射吸收光谱(UV-Vis)的结果表明: 两种阵列的纳米管均为六角形结构, 直径约为100 nm, 壁厚约为20 nm; 在N-TiO2/ZnO复合纳米管阵列中, 掺入的N离子主要是以N-Ox、N-C和N-N的形式化学吸附在纳米管表面, 仅有少量的N离子以取代式掺杂的方式占据TiO2晶格O的位置; 表面N物种形成的表面态能级和取代式掺杂导致带隙的窄化, 增强了纳米管阵列的光吸收效率, 促进了光生载流子的分离. 光催化实验结果表明, N离子的掺杂有利于N-TiO2/ZnO复合纳米管阵列光催化活性的提高.     

N-TiO2/ZnO复合纳米管阵列的掺杂机理及其光催化活性

以ZnO纳米柱阵列为模板, 采用溶胶-凝胶法制备出TiO2/ZnO和N掺杂TiO2/ZnO的复合纳米管阵列. 扫描电镜(SEM)、X射线光电子能谱(XPS)和紫外-可见漫反射吸收光谱(UV-Vis)的结果表明: 两种阵列的纳米管均为六角形结构, 直径约为100 nm, 壁厚约为20 nm; 在N-TiO2/ZnO复合纳米管阵列中, 掺入的N离子主要是以N-Ox、N-C和N-N的形式化学吸附在纳米管表面, 仅有少量的N离子以取代式掺杂的方式占据TiO2晶格O的位置; 表面N物种形成的表面态能级和取代式掺杂导致带隙的窄化, 增强了纳米管阵列的光吸收效率, 促进了光生载流子的分离. 光催化实验结果表明, N离子的掺杂有利于N-TiO2/ZnO复合纳米管阵列光催化活性的提高.     

N-TiO2/ZnO复合纳米管阵列的掺杂机理及其光催化活性

以ZnO纳米柱阵列为模板, 采用溶胶-凝胶法制备出TiO2/ZnO和N掺杂TiO2/ZnO的复合纳米管阵列. 扫描电镜(SEM)、X射线光电子能谱(XPS)和紫外-可见漫反射吸收光谱(UV-Vis)的结果表明: 两种阵列的纳米管均为六角形结构, 直径约为100 nm, 壁厚约为20 nm; 在N-TiO2/ZnO复合纳米管阵列中, 掺入的N离子主要是以N-Ox、N-C和N-N的形式化学吸附在纳米管表面, 仅有少量的N离子以取代式掺杂的方式占据TiO2晶格O的位置; 表面N物种形成的表面态能级和取代式掺杂导致带隙的窄化, 增强了纳米管阵列的光吸收效率, 促进了光生载流子的分离. 光催化实验结果表明, N离子的掺杂有利于N-TiO2/ZnO复合纳米管阵列光催化活性的提高.     

A reevaluation of the correlation between the synthesis parameters and structure and properties of nitrogen-doped carbon nanotubes

Nitrogen-doped carbon nanotubes(NCNTs) were synthesized by chemical vapor deposition using cobaltbased oxides as catalyst and ethylenediamine(EDA) as carbon/nitrogen precursor. The influence of growth time,EDA concentration and growth temperature on the morphology,yield,composition,graphitization and oxidation resistance of the NCNTs was systematically investigated by using Raman spectroscopy,temperature-programmed oxidation and other techniques. The NCNT growth from ethylenediamine with a high N/C ratio involves several processes including mainly(1) catalytic growth of NCNTs,(2) homogeneous gas-phase decomposition of EDA,(3) non-catalytic deposition of pyrolytic carbon/nitrogen species and(4)surface etching of amorphous carbon or carbon at defect sites through gasification. At a later growth stage the etching process appears to be dominating,leading to the thinning of nanotubes and the decrease of yield.Moreover,the surface etching through carbon gasification strongly influences the structure and degree of graphitization of NCNTs.     

Purified oxygen- and nitrogen-modified multi-walled carbon nanotubes as metal-free catalysts for selective olefin hydrogenation

Oxygen- and nitrogen-functionalized carbon nanotubes (OCNTs and NCNTs) were applied as metal-free catalysts in selective olefin hydrogenation. A series of NCNTs was synthesized by NH₃ post-treatment of OCNTs. Temperature-programmed desorption, N₂ physisorption, Raman spectroscopy, high-resolution transmission electron microscopy and X-ray photoelectron spectroscopy were employed to characterize the surface properties of OCNTs and NCNTs, aiming at a detailed analysis of the type and amount of oxygen- and nitrogen-containing groups as well as surface defects. The gas-phase treatments applied for oxygen and nitrogen functionalization at elevated temperatures up to 600 °C led to the increase of surface defects, but did not cause structural damages in the bulk. NCNTs showed a clearly higher activity than the pristine CNTs and OCNTs in the hydrogenation of 1,5-cyclooctadiene, and also the selectivity to cyclooctene was higher. The favorable catalytic properties are ascribed to the nitrogen-containing surface functional groups as well as surface defects related to nitrogen species. In contrast, oxygen-containing surface groups and the surface defects caused by oxygen species did not show clear contribution to the hydrogenation catalysis.     

聚苯胺改性氮掺杂碳纳米管制备及其超级电容器性能

利用苯胺原位化学聚合合成聚苯胺包覆碳纳米管(CNTs), 再炭化处理制备氮掺杂碳纳米管(NCNTs).激光拉曼(Raman)光谱和X射线光电子谱(XPS)分析及透射电镜(TEM)观察表明, 苯胺包覆碳纳米管经炭化处理后, 得到以碳纳米管为核、氮掺杂碳层为壳, 具有核-壳结构的氮掺杂碳纳米管, 而碳纳米管本征结构未遭破坏. 研究表明, 随着苯胺用量的增大, 氮掺杂碳纳米管的氮掺杂碳层变厚, 氮含量从7.06%(质量分数)增加到8.64%, 而作为超级电容器电极材料, 随着氮掺杂碳层厚度降低, 氮掺杂碳纳米管在6 mol·L^-1氢氧化钾电解液中的比容量从107 F·g^-1增大到205 F·g^-1, 远高于原始碳纳米管10 F·g^-1的比容量, 且聚苯胺改性氮掺杂碳纳米管表现出较好的充放电循环性, 经1000次充放电循环后仍保持初始容量的92.8%~97.1%, 表明氮掺杂碳纳米管不仅通过表面氮杂原子引入大的法拉第电容和改善亲水性使电容量显著增大, 其具有的核壳结构特征也使循环稳定性增强。     

Physical and electrochemical characterizations of microwave-assisted polyol preparation of carbon-supported PtRu nanoparticles

PtRu nanoparticles supported on Vulcan XC-72 carbon and carbon nanotubes were prepared by a microwave-assisted polyol process. The catalysts were characterized by transmission electron microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy (XPS). The PtRu nanoparticles, which were uniformly dispersed on carbon, were 2-6 nm in diameter. All PtRu/C catalysts prepared as such displayed the characteristic diffraction peaks of a Pt face-centered cubic structure, excepting that the 2theta values were shifted to slightly higher values. XPS analysis revealed that the catalysts contained mostly Pt(0) and Ru(0), with traces of Pt(II), Pt(IV), and Ru(IV). The electro-oxidation of methanol was studied by cyclic voltammetry, linear sweep voltammetry, and chronoamperometry. It was found that both PtRu/C catalysts had high and more durable electrocatalytic activities for methanol oxidation than a comparative Pt/C catalyst. Preliminary data from a direct methanol fuel cell single stack test cell using the Vulcan-carbon-supported PtRu alloy as the anode catalyst showed high power density.     

Ru Nanoparticles Supported on Co-Embedded N-Doped Carbon Nanotubes as Efficient Electrocatalysts for Hydrogen Evolution in Basic Media

A challenging but urgent task is to construct efficient and robust hydrogen evolution reaction(HER) electrocatalysts for practically feasible and sustainable hydrogen production through alkaline water electrolysis. Herein we report a simple and mild pyrolysis method to synthesize the efficient Ru nanoparticles(NPs) supported on Co-embedded N-doped carbon nanotubes(Ru/Co-NCNTs) catalyst for HER in basic media. The Ru/Co-NCNTs display remarkable performance with a low overpotential of only 35 mV at 10 mA/cm², a small Tafel slope(36 mV/dec), and a high mass activity in 1 mol/L KOH, which is superior to commercial 20% Pt/C catalyst. This excellent performance is benefited from the enhanced conductivity of N-doped carbon nanotubes(NCNTs) and high intrinsic activity triggered by synergistic coupling between Ru NPs and Co-embedded N-doped carbon nanotubes(Co-NCNTs).     

Nanostructure PtRu/MWNTs as anode catalysts prepared in a vacuum for direct methanol oxidation

Platinum and ruthenium nanoparticles that are uniformly dispersed on multiwalled carbon nanotubes (MWNTs) were synthesized by vacuum pyrolysis using Pt(acac)2 and Ru(acac)3 as the metal precursors. The resulting nanocomposites were characterized by transmission electron microscopy and X-ray diffraction. The Pt, Pt45Ru55, and Ru nanoparticles had mean diameters of 3.0 +/- 0.6, 2.7 +/- 0.6, and 2.5 +/- 0.4 nm and the same mole number as their metal precursors at 500 degrees C. The electrocatalytic activity of the Pt/MWNTs and PtRu/MWNTs was investigated at room temperature by cyclic voltammetry and chronoamperometry. All of the electrochemical results showed that the PtRu/MWNTs exhibited a high level of catalytic activity for methanol oxidation as a result of the large surface area of the supporting carbon nanotubes and the wide dispersion of the Pt and Ru nanoparticles. Compared with the Pt/MWNTs, the onset potential for methanol oxidation of the PtRu/MWNTs was significantly lower, and the ratio of the forward anodic peak current to the reverse anodic peak current during methanol oxidation was somewhat higher. The Pt45Ru55/MWNTs displayed the best electrocatalytic activity of all of the carbon-nanotube-supported Pt and PtRu catalysts.     

Nitrogen-doped carbon nanotubes as a cathode catalyst for the oxygen reduction reaction in alkaline medium

A new approach to synthesize nitrogen-doped carbon nanotubes (NCNTs) as catalysts for oxygen reduction by treating oxidized CNTs with ammonia is presented. The surface properties and oxygen reduction activities were characterized by cyclic voltammetry, rotating disk electrode and X-ray photoelectron spectroscopy. NCNTs treated at 800 °C show improved electrocatalytic activity for oxygen reduction as compared with commercially available Pt/C catalysts.     

CVD growth of N-doped carbon nanotubes on silicon substrates and its mechanism

In the present study, we report the chemical vapor deposition (CVD) of nitrogen-doped (N-doped) aligned carbon nanotubes on a silicon (Si) substrate using ferrocene (Fe(C5H5)2) as catalyst and acetonitrile (CH3CN) as the carbon source. The effect of experimental conditions such as temperature, gaseous environment, and substrates on the structure and morphology of N-doped carbon nanotubes arrays is reported. From XPS and EELS data, it was found that the nitrogen content of the nanotubes could be determined over a wide range, from 1.9% to 12%, by adding the addition of hydrogen (H2) to the reaction system. It was also shown by SEM that N-doped carbon nanotube arrays could be produced on Si and SiO2 substrates at suitable temperatures, although at different growth rates. Using these concentrations, it was possible to produce three-dimensional (3D) carbon nanotubes architectures on predetermined Si/SiO2 patterns. The mechanism underlying the effect of nitrogen containing carbon sources on nanotube formation was explored using X-ray photoelectron spectroscopy (XPS).     

Ruthenium nanoparticles embedded in mesoporous carbon microfibers: preparation, characterization and catalytic properties in the hydrogenation of D-glucose

Ruthenium (Ru) nanoparticles dispersed in mesoporous carbon microfibers were prepared using alumina microfibers as the templates via a chemical vapour deposition (CVD) route. Characterized data showed that Ru nanoparticles were embedded in the mesoporous carbon matrix. The samples were found to possess a specific surface area as high as 750 m(2) g(-1), pore sizes in the range of 3-5 nm, lengths in the range of 5-10 μm, and a width of about 0.5 μm. The Ru catalysts displayed a remarkably high catalytic activity and an excellent stability in the hydrogenation of D-glucose. The observed good catalyst performance is attributed to the carbon microfiber morphology, unblocked mesoporous structure, and the hydrogen spillover effect induced by the unique surface contact between the Ru nanoparticles and the carbon. In addition, the incorporation of nitrogen significantly improved the catalytic performance due to the enhanced hydrogen adsorption, better wettability, and modified electronic properties of the Ru.     

Carbon nanotube assisted synthesis of CeO2 nanotubes

CeO₂ nanotubes have been synthesized facilely using carbon nanotubes (CNTs) as templates by a liquid phase deposition method. The properties of the CeO₂ nanotubes were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectrum (XPS) as well as thermogravimetry and differential thermal analysis (TG-DTA). The obtained CeO₂ nanotubes with a polycrystalline face-centered cubic phase have a uniform diameter ranging from 40 to 50 nm. The CeO₂ nanotubes are composed of many tiny interconnected nanocrystallites of about 10 nm in size. The pretreatment of CNTs and calcination temperature were confirmed to be the crucial factors determining the formation of CeO₂ nanotubes. A possible formation mechanism has been suggested to explain the formation of CeO₂ nanotubes.