Ba修饰的Pd/A12O3对苯酚液相原位加氢制环己酮反应的催化性能

利用等体积浸渍法制备了一系列不同助剂修饰的Pd/AI2O3催化剂,并考察了催化剂对苯酚液相原位加氢制环己酮反应的催化性能.结果表明,Ba-Pd/AI2O3对苯酚液相原位加氧反应有较优的催化性能.当w(Ba)=3%时,苯酚转化率可比Pd/AI2O3催化剂提高近2倍.在优化的反应条件下,苯酚转化率可达100%,环己酮收率可达80%.利用透射电子显微镜、CO化学吸附、X射线衍射、N2吸附-脱附和CO2程序升温脱附等手段表征了不同Ba含量的Pd/AI2O3催化剂的物理化学性质.结果表明,Ba的添加可明显提高Pd在AI2O3表面的分散度,同时增强了催化剂表面的碱性.这是Ba-Pd/AI2O3对苯酚液相原位加氢制环己酮反应具有较优催化性能的重要原因.     

苯酚加氢制环己酮用高效Pd/MgAl-LDO@Al2O3催化剂的制备及性能研究

环己酮是合成尼龙等材料的重要中间体, 但苯酚直接加氢反应制备环己酮容易生成环己醇而降低收率. 采用原位生长策略制备Pd/MgAl-LDO@Al₂O₃催化剂, 并用于苯酚选择性加氢反应, 获得的催化剂在高底物比条件具有良好的催化性能, 相较于Pd/Al₂O₃催化剂, Pd/MgAl-LDO@Al₂O₃催化剂使苯酚转化率显著增加, 苯酚转化率在97%时环己酮选择性可达88%. 利用X射线衍射(XRD)、程序升温脱附(TPD)、高分辨透射电子显微镜(HRTEM)和X射线光电子能谱(XPS)等手段对催化剂结构进行表征发现在氧化铝上原位生长类水滑石结构能够优化催化剂孔结构并提高活性组分分散度, 且增加了载体表面碱位点的强度, 碱位点的存在影响了苯酚的吸附形式, 从而大幅增加环己酮的选择性. 此外, 当将Ni引入层状结构时, 通过NaBH₄的还原可获得PdNi合金结构. 动力学研究表明, 由于PdNi合金的形成, Pd/NiAl-LDO@Al₂O₃催化剂苯酚加氢反应的能垒低于Pd/MgAl-LDO@Al₂O₃, 同时合金结构导致环己酮选择性的明显降低.     

Pd-Ce-B/水滑石催化液相苯酚选择性加氢制环己酮

以Al3 /(Al3 Mg2 )摩尔比为0.2的水滑石(HT)为载体,采用还原浸渍法制备了负载型Pd-Ce-B/HT催化剂,并将其应用于液相苯酚选择性加氢制环己酮.与Pd-Ce-B/Al2O3,Pd-Ce-B/MgO和Pd-Ce-B/SiO2相比,Pd-Ce-B/HT催化剂具有高活性和高环己酮选择性.5.8%Pd-Ce-B/HT上苯酚的转化率和环己酮的选择性分别达82.0%和80.3%,显示了其潜在的工业化应用前景.根据多种表征结果,初步讨论了催化剂的构效关系以及添加剂Ce3 和载体酸碱性对催化性能的促进作用.     

载体焙烧温度对稀燃天然气汽车尾气净化Pd/Zr0.5Al0.5O1.75催化剂性能的影响

以不同温度焙烧得到的Zr0.5Al0.5O1.75复合氧化物为载体,制备了系列1.5%Pd/Zr0.5Al0.5O1.75催化剂样品.采用N2吸附-脱附、X射线衍射、H2程序升温还原、O2程序升温脱附及CO化学吸附等手段对催化剂进行了表征,并测试了催化剂在模拟稀燃天然气汽车尾气中的活性和抗H2O中毒性能.结果表明,载体...     

铌改性的Pd/Al2O3催化剂催化苯燃烧反应简

采用浸渍法制备了Nb改性的Pd/Al2O3催化剂,考察了该催化剂催化苯燃烧反应性能,并研究了催化剂的稳定性. 结果表明,Nb的添加明显提高了Pd/Al2O3催化剂性能,在195 ℃时苯转化率达到90%,苯的完全燃烧温度降低了40 ℃. 采用X射线衍射(XRD)、X射线光电子能谱(XPS)、透射电子显微镜(TEM)、H2 程序升温还原(H2-TPR)、NH3程序升温脱附(NH3-TPD)和氮气吸附等手段对催化剂进行了表征,结果表明,Nb的加入不仅提高了Pd物种的分散度,同时改变了部分Pd的价态,形成适宜反应的PdO-Pd物种,并促进了催化剂表面氧浓度的增加,使氧物种氧化能力增强,从而提高了催化性能. 1%Pd-5%Nb/Al2O3催化剂的催化活性高于2.0%Pd/Al2O3催化剂.     

铌改性的Pd/Al_2O_3催化剂催化苯燃烧反应

采用浸渍法制备了Nb改性的Pd/Al2O3催化剂,考察了该催化剂催化苯燃烧反应性能,并研究了催化剂的稳定性.结果表明,Nb的添加明显提高了Pd/Al2O3催化剂性能,在195℃时苯转化率达到90%,苯的完全燃烧温度降低了40℃.采用X射线衍射(XRD)、X射线光电子能谱(XPS)、透射电子显微镜(TEM)、H2程序升温还原(H2-TPR)、NH3程序升温脱附(NH3-TPD)和氮气吸附等手段对催化剂进行了表征,结果表明,Nb的加入不仅提高了Pd物种的分散度,同时改变了部分Pd的价态,形成适宜反应的PdO-Pd物种,并促进了催化剂表面氧浓度的增加,使氧物种氧化能力增强,从而提高了催化性能.1%Pd-5%Nb/Al2O3催化剂的催化活性高于2.0%Pd/Al2O3催化剂.     

焙烧温度对 Pd/Al2O3 催化剂上甲烷燃烧反应性能的影响

 考察了载体与催化剂焙烧温度对 Pd/Al2O3 催化剂上低浓度甲烷催化燃烧反应性能的影响. 采用 X 射线衍射、透射电镜、N2 物理吸附、NH3 程序升温脱附和 O2 程序升温氧化等手段对载体和催化剂进行了表征. 结果表明, 焙烧温度对催化剂活性及稳定性的影响显著. 随着载体焙烧温度的升高, Al2O3 的比表面积、物相结构、酸中心的数量及强度明显改变, 相应的 Pd/Al2O3 催化剂中载体与 Pd 的相互作用减弱, Pd 分散度降低. 当载体焙烧温度为 1 100 °C, Pd/Al2O3 焙烧温度为 200 °C 时, 所得催化剂在 260 h 的连续反应中, 甲烷转化率始终维持在 99%以上.     

过渡金属对燃烧法制MgO负载 Cu2O催化剂的改性研究

本文以柠檬酸燃烧法制备MgO(B)载体,采用浸渍还原法以水合肼为还原剂制备Cu2O/MgO(B)催化剂,以环己醇脱氢制环己酮为探针反应,考察了过渡金属Fe、Co、Ni、Mo、Mn的添加对Cu2O/MgO(B)催化性能的影响;采用X射线衍射(XRD)、程序升温还原(TPR)、二氧化碳程序升温脱附(CO2-TPD)以及环己醇、环己酮程序升温脱附(环己醇/环己酮-TPD) 等手段对催化剂进行了表征.研究结果表明,Mn-Cu2O/MgO(B) 、 Ni-Cu2O/MgO(B)的催化性能优于Cu2O/MgO(B).其原因主要是Mn、Ni的添加使Cu2O的抗还原能力增强,Cu2O更稳定;同时,Mn和Ni的添加使Cu2O/MgO(B)催化剂对反应物和产物的吸附强度减弱;这些都有利于脱氢反应的进行.所有催化剂都呈碱性,是其具有高环己酮选择性的原因之一.     

钕对苯直接氧化制苯酚催化反应的促进作用

采用溶胶凝胶法制备Cr/Al2O3,Nd-Cr/Al2O3催化剂,通过X射线衍射(XRD)、N2吸附脱附和透射电子显微镜(TEM)对催化剂进行表征,结果表明稀土的加入增加了负载过渡金属的氧化铝的比表面积,使孔道结构更加规则有序。程序升温脱附(TPD)、程序升温还原(TPR)、X射线光电子能谱(XPS)和27Al固体核磁共振(27Al MAS NMR)的表征进一步说明稀土金属和过渡金属对载体表面性质和Al配位的影响,在催化反应中铬是主催化剂,钕是助催化剂。将催化剂用于苯一步氧化制备苯酚的反应中,反应结果表明所得催化剂均具有较高活性,并且Nd-Cr/Al2O3的催化活性高于Cr/Al2O3。     

负载型金催化剂催化乙醇选择氧化反应

选择不同氧化物(Al2O3,SiO2,TiO2,MgO)和H-ZSM-5分子筛作为载体,以尿素为沉淀剂,采用沉积-沉淀法制备了一系列负载型金催化剂.采用X射线衍射、电感耦合等离子体发射光谱、程序升温还原、NH3程序升温脱附和透射电镜等技术对催化剂样品进行了表征,并测定了催化剂对乙醇选择氧化反应的催化性能.选择Au/Al2O3催化剂,考察了金负载量、反应条件(温度、压力、时间)和添加剂对乙醇选择氧化反应的影响.结果表明,所制备的Au/Al2O3催化剂的金负载率较高,金粒子较小(3～4 nm)且分布均匀.载体对金催化剂催化乙醇氧化反应有显著影响,主要产物为乙醛、乙酸乙酯和缩醛.以TiO2为载体时,乙醇转化率较高.以Al2O3为载体时,乙酸乙酯选择性较高;少量碱性添加剂可抑制缩醛的生成,并可提高乙醇转化率和乙酸乙酯选择性.在优化的条件下,乙醇转化率可达4.7%,乙酸乙酯选择性可达93.5%.     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

化学计量中不确定度评定研究进展

测量不确定度是表征合理地赋予被测量之值的分散性的参数。本文针对化学计量不确定度评定基础模型仅适用于线性模型、概率分布为正态分布或缩放位移t分布等局限,介绍了近年来不确定度评定的研究热点:蒙特卡罗方法(Monte Carlo Method,MCM),不确定度评定的来源、评定概念、评估方法及其发展过程,扩大了测量不确定度评定与表示的适用范围。     

微量钙的测定方法研究进展

介绍了1995-2006年期间测定微量和痕量钙的方法,如电感耦合等离子体-原子发射光谱法、原子吸收光谱法以及离子色谱法等的工作原理和特点,并说明了其测定微量钙的应用领域。并对微量钙的测定技术进行了展望(引用文献55篇)。     

Stages of thermal decomposition of sodium oxo-salts of sulphur

Thermal behaviour of sodium oxo-salts of sulphur: Na₂SO₄, Na₂S₂O₇, Na₂S₂O₆, Na₂SO₃, Na₂S₂O₅, Na₂S₂O₄, Na₂S₂O₃, Na₂S₃O₆ and of sulphides Na₂S and Na₂S₂ was studied on heating up to 1000°C. The experiments were performed with anhydrous compounds obtained from commercial products by recrystallisation and dehydration. The stage mechanisms of decomposition of anionic sub-lattices of the salts have been proposed basing on the Górski’s morphological classification of simple species. The thermal stability and the stage decomposition mechanisms were correlated with the structure and the potential chemical properties of the salt anions. The thermal decomposition processes were studied by means of thermal analysis, and the decomposition products were identified by means of X-ray phase analysis.