Oximidobenzotetronic acid as a reagent for the separation and gravimetric determination of palladium and cobalt

Oximidobenzotetronic acid is recommended for the separation and gravimetric determination of palladium and cobalt An ethanolic solution of the reagent quantitatively precipitates palladium(II) from solutions which are 0.75 N in acid up to pH 5.1, the complex is weighed as Pd(C₉H₅NO₄)₂. Cobalt(II) can be determined in the filtrate after the precipitation of palladium. With 0.5 N acid solutions, no interference was found from Pt(IV), Ir(IV), Rh(III), Ru(III), Os(IV), Au(III), Ag(I), Cu(II), Fe(III), Ni(II), Hg(II). Pb(II), Bi(III), Cd(II), As(V), Se(VI), Te(IV), Mo(VI), Sb(III), Al(III), Cr(III), Zn(II), Ti(IV), Zr(IV). acetate, oxalate, citrate, tartrate, phosphate and fluoride.     

Spectrophotometric determination of copper(II) using oximidobenzotetronic acid

Summary Oximidobenzotetronic acid (OBTA) is proposed as a sensitive spectrophotometric reagent for the estimation of 0.5–3.0 ppm of copper(II) at 427 nm in 50% dioxan at p_H 5.3–7.5. For the estimation of 2 ppm Cu(II), 1.3 ppm Ni(II), 1.3 ppm Co(II), 3.2 ppm Fe(II), 10.3 ppm Fe(III), 9.7 ppm Ce(IV), 300 ppm acetate, 160 ppm oxalate, 95 ppm tartrate, 50 ppm citrate, as well as Zn(II), Cd(II), Hg(II)) Pb(II), Mn(II), As(III) as well as (V), Th(IV), Be(II), Ce(III), La(III), V(V) and Mo(VI), even when present in large quantities, do not interfere. The interference due to 25 ppm Bi(III), 20 ppm Sb(III), 20 ppm Sn(II), 25 ppm Sn(IV) and 30 ppm W(VI) can be removed by the addition of 95 ppm tartrate ions.

---

Zusammenfassung Oximidobenzotetronsäure wurde als empfindliches Reagens zur spektrophotometrischen Bestimmung von 0,5 bis 3,0 ppm Kupfer(II) bei 427 nm in 50%iger Dioxanlösung bei p_H 5,3 bis 7,5 vorgeschlagen. Die Anwesenheit von 1,3 ppm Ni(II), 1,3 ppm Co(II), 3,2 ppm Fe(II), 10,3 ppm Fe(III), 9,7 ppm Ce(IV), 300 ppm Acetat, 160 ppm Oxalat, 95 ppm Tartrat, 50 ppm Citrat sowie die Anwesenheit auch großer Mengen Zn(II), Cd(II), Hg(II), Pb(II), Mn(II), As(III) bzw. (V), Th(IV), Be(II), Ce(III), La(III), V(V) und Mo(VI) stören die Bestimmung von 2 ppm Cu(II) nicht. Der störende Einfluß von 25 ppm Bi(III), 20 ppm Sb(III), 20 ppm Sn(II), 25 ppm Sn(IV) und 30 ppm W(VI) kann durch Zusatz von 95 ppm Tartrat beseitigt werden.

     

Application of the Weisz Ring oven technique to the separation and identification of micro-quantities of some less familiar cations

Summary Use of the ring oven in separation and identification of mixtures of less familiar metal ions has been described. Separation of metal ions from the following mixtures has successfully been carried out: 1. UO₂(II) and Th(IV), 2. Th(IV) and Ce(IV), 3. Pd(II) and Au(III), 4. Pt(IV) and Au(III), 5. Ce(III) and Ce(IV), 6. UO₂(II), Th(IV) and Ti(IV), 7. Th(IV), Ti(IV) and Ce(IV), 8. Th(IV), Ce(IV) and Zr(IV), 9. Ti(IV), V(V) and Zr(IV), 10. Mo(VI), V(V) and W(VI) and 11. Be(II), Al(III) and Mg(II). In the case of binary mixtures, the separation was in the form of a central spot and a concentric ring; in ternary mixtures the metals were precipitated in a central spot and two concentric rings.

---

Zusammenfassung Zur Trennung und Identifizierung folgender Gemische seltenerer Metallionen wurde der Ringofen mit Erfolg verwendet: 1. UO₂(II) und Th(IV), 2. Th(IV) und Ce(IV), 3. Pd(II) und Au(III), 4. Pt(IV) und Au(III), 5. Ce(III) und Ce(IV), 6. UO₂(II), Th(IV) und Ti(IV), 7. Th(IV), Ti(IV) und Ce(IV). 8. Th(IV), Ce(IV) und Zr(IV), 9. Ti(IV), V(V) und Zr(IV), 10. Mo(VI), V(V) und W(VI) und 11. Be(II), Al(III) und Mg(II). Bei binären Gemischen erfolgt die Trennung in einen zentralen Fleck und einen Ring, bei ternären Mischungen in einen Fleck und zwei konzentrische Ringe.

---

Résumé On a décrit l'utilisation du four annulaire pour la séparation et l'identification de mélanges d'ions métalliques moins courants. On a effectué la séparation des ions métalliques à partir des mélanges suivants: 1. UO₂(II) et Th(IV), 2. Th(IV) et Ce(IV), 3. Pd(II) et Au(III), 4. Pt(IV) et Au(III), 5. Ce(III) et Ce(IV), 6. UO₂(II), Th(IV) et Ti(IV), 7. Th(IV), Ti(IV) et Ce(IV), 8. Th(IV), Ce(IV) et Zr(IV), 9. Ti(IV), V(V) et Zr(IV), 10. Mo(VI), V(V) et W(VI) et 11. Be(II), Al(III) et Mg(II). Dans le cas des mélanges binaires, la séparation se présentait sous forme d'une tache centrale et d'un anneau concentrique; chez les mélanges ternaires, les métaux étaient précipités en une tache centrale et deux anneaux concentriques.

     

Chloroform extraction of ethyl xanthate complexes from sulphuric acid media

The chloroform extraction of 30 elements (Fe, Co, Ni, Zn, Cd, Ge, Sn, V, As, Sb, Bi, Cu, Ag, Au, Mn, Re, Ga, In, Tl, Se, Te, Cr, Mo, U, Pt, Pd, Rh, Ir, Ru and Ce) from 0.1-8M sulphuric acid in the presence of potassium ethyl xanthate has been studied. Pd(II), Bi, As(III), Sb(III), Se(IV) and Te(IV) are completely extracted and Au(III) is largely extracted over the range of acid concentration investigated. Fe(II), Tl(I), Rh(III) and Cr(VI) are only slightly extracted and Se(VI), Te(VI), Ru(III), Cr(III), Mn(II), Zn, Ce(IV), Ir(IV) and Ge(IV) are not extracted at all. Depending on the acid concentration, the remaining elements are all partly extracted. Results are compared with those obtained in an earlier study of the extraction of xanthate complexes from hydrochloric acid media. The processes involved in the formation of some xanthate complexes and potential analytical separations are discussed.     

Extraction and separation of bismuth(III) from steel and bismuth-base alloys

Summary Separation of bismuth(III) from iron(III), molybdenum(VI), vanadium(V), chromium(VI), titanium(IV), antimony(III), lead(II), beryllium(II), uranium(VI), hafnium(IV), indium(III) and zirconium (IV) is achieved by solvent extraction with high molecular weight amines from sodium succinate solution adjusted to suitable pH. Bismuth(III) is stripped from the organic phase and determined spectrophotometrically. The method is shown to be applicable to bismuth alloys.

---

Extraktion und Trennung von Wismut(III) aus Stahl und wismuthältigen Legierungen

Zusammenfassung Wismut(III) läßt sich von Fe(III), Mo(VI), V(V), Cr(VI), Ti(IV), Sb(III), Pb(II), Be(II), U(VI), Hf(IV), In(III) und Zr(IV) durch Extraktion mit hochmolekularen Aminen aus Natriumsuccinat bei geeignetem pH trennen. Bi(III) wird dann von der organischen Phase getrennt und spektralphotometrisch bestimmt. Das Verfahren eignet sich für Wismutlegierungen.

     

Physicochemical and Biological Studies on Xipamide and Some of Its Complexes

Russian Journal of General Chemistry - The new complexes of xipamide (XPD) with Ti(III), Ni(II), Pd(II), Zr(IV), Ce(IV), and U(VI) have been synthesized. Elemental analysis, magnetic properties,...     

Adsorption of metal ions on activated carbon from aqueous solutions at pH 1-13

Adsorption of microgram amounts of 20 metal species on activated carbon powder from aqueous solutions of pH 1-13 was investigated. The species examined were Cs(I), Y(III), Ce(III), Ti(IV), Zr(IV), Cr(III), Cr(VI), Mn(II), Fe(III), Co(II), Ni(II), Ru(III), Cu(II), Ag(I), Zn(II), Cd(II), Al(III), Pb(II), Sb(III) and Bi(III).     

Titrimetric determination of U(iv) alone and in mixtures with V(IV), Mn(II), Ce(III) and Fe(II)

Summary A rapid and accurate method is described for the potentiometric determination of uranium(IV) with permanganate at room temperature using trace amounts of ortho-phosphoric acid as a catalyst. The procedure has been extended for the differential potentiometric determination of mixtures with vanadium, manganese or cerium. The methods are easy, non-time consuming and free from interference by a large number of foreign ions. Conditions are also developed for the differential photometric determination of uranium and iron in mixtures.Based on these procedures, a differential titrimetric procedure has been developed for determination of iron(III), vanadium(V), chromium(VI) and manganese(VII) [or cerium(IV)] in a single solution at room temperature. This procedure has also been tested on Bureau of Standard samples.

---

Titrimetrische Bestimmung von U(IV) allein und in Mischungen mit V(IV), Mn(II), Ce(III) und Fe(II)Anwendung auf die Analyse von Stählen und Legierungen

Zusammenfassung Eine schnelle und genaue Methode wird beschrieben zur potentiometrischen Bestimmung von Uran(IV) mit Permanganat bei Raumtemperatur unter Verwendung von Spuren Orthophosphorsäure als Katalysator. Das Verfahren wurde auf die differentialpotentiometrische Bestimmung im Gemisch mit V, Mn und Ce ausgedehnt. Die rasch und einfach ausführbare Methode wird durch zahlreiche Fremdionen nicht gestört. Eine differentialphotometrische Bestimmung von U(IV) und Fe(II) im Gemisch wird ebenfalls angegeben, außerdem eine differentialtitrimetrische Bestimmung von Fe(III), V(V), Cr(VI), Mn(VII) [oder Ce(IV)] in einer Lösung. Anwendungsbeispiele für Stähle und Legierungen werden beschrieben.

     

Pyrimidinethiol as a reagent for extraction separation of platinum metals and gold Determination of Pd(II), Os(VIII) and Ru(III)

The solvent extraction separation of Pt(IV), Pd(II), Os(VIII), Ru(III) and Au(III) from one another and also from Rh(III) and Ir(III) with 1-(2'-nitro-4'-tolyl)-4,4,6-trimethyl-(1H, 4H)-2-pyrimidinethiol has been investigated. Photometric procedures have been developed for the determination of Pd(II), Os(VIII) and Ru(III) with the same reagent. The reagent allows the enrichment of Pd(II) and Au(III) at the trace level from a large volume of aqueous medium even in the presence of base metals. The method can be used for the determination of platinum metals and gold in alloys.     

Extraction behavior of Tm(III), Dy(III) and Sm(III) lanthanide with N-benzoyl-N-phenylhydroxalamine

The extraction of Sm(III), Dy(III) and Tm(III) with N-benzoyl-N-phenylhydroxalamine (BPHA) in benzene at pH range (1–10) has been studied. Quantitative separation was found in borate media at pH 8. The slope analysis showed that the extracted complex was M(BPHA)₃, where M=Sm(III), Dy(III) and Tm(III). The effect of various masking agents indicated that EDTA, oxalate, fluoride, phosphate and citrate, interfered in this study. Decontamination study showed that Cu(II), Zn(II), Ni(II), Co(II), Cr(III), Sc(III) and Fe(III) had very poor separation factors, whereas Sn(II), Cd(II), In(III), Ru(II), Hg(II), Ag(I), Ta(V) and Hf(IV) had very large separation factor. The effect of different diluents showed that carbontetrachloride, chloroform, benzene, toluene, nitrobenzene dichloromethane, MIBK and cyclohexanone were equally good for extraction except TBP due to ion association.     

Electron transfer. 157. Reactions of hypervalent manganese species with S(2) metal-ion reductants

Solutions of the complexes of hypervalent manganese, [Mn(III)(C(2)O(4))(3)](3)(-) (in oxalate buffers), [Mn(IV)(bigH)(3)](4+) (in biguanide buffers), and [(bipy)(2)Mn(III)(O)(2)Mn(IV)(bipy)(2)](3+) (in bipyridyl buffers) may be reduced by s(2) center reductants In(I), Sn(II), and Ge(II), yielding Mn(II) quantitatively. In all cases, rates are determined by the initial act of electron transfer, giving an s(1) transient (In(II), Sn(III), or Ge(III)); subsequent steps are rapid and kinetically silent. The In(I)-Mn(III) and Ge(II)-Mn(III) reactions are inhibited by added oxalate, whereas the Sn(II)-(Mn(III)Mn(IV)) reaction is strongly accelerated by Cl(-). The In(I)-Mn(IV) reaction is complicated by formation of a 1:1 addition compound In(I).Mn(IV). We find no evidence for two-unit steps in any of these systems.     

Liquid-liquid extraction of niobium(V) in the presence of other metals with high molecular mass amines and ascorbic acid

A novel method is proposed for the solvent extraction of niobium(V). A 0.1M solution of Aliquat 336S in xylene quantitatively extracts microgram quantities of niobium(V) from 0.01M ascorbic acid at pH 3.5-6.5. Niobium from the organic phase is stripped with 0.5M nitric acid and determined spectrophotometrically in the aqueous phase as its complex with TAR. The method permits separation of niobium not only from tantalum(V) but also from vanadium(IV), titanium(IV), zirconium(IV), thorium(IV), chromium(III), molybdenum(VI), uranium(VI), iron(III), etc. Niobium from stainless steel was determined with a precision of 0.42%.     

Disodium-1,8-dihydroxy-naphthalene-3,6-disulphonate (chromotropic salt) as a reagent in inorganic analysis

Summary The compound disodium-1,8-dihydroxy-naphthalene-3,6-disulphonate (sodium salt of chromotropic acid) is employed as a colorimetric reagent for titanium. It is also known to produce coloured complexes with chromium(VI), vanadium and uranium. In the present paper the formation of colour with forty metallic ions has been studied qualitatively, in neutral as well as in alkaline and acidic media. It has been found that the reagent yields coloured complexes with mercury(I), tin(IV), platinum(IV), gold(III), tellurium(VI), molybdenum(VI), iron(III), aluminium(III), chromium(III), and uranyl(II) besides those recorded above.The colour reactions are particularly sensitive to uranyl(II), iron(III), mercury(I), tin(IV), gold(III) und molybdenum(VI).     

Extraction of molybdenum(V) as its ferron complex with trioctylamine in chloroform from a sulphuric acid medium

A simple, rapid, and highly selective method for the separation of molybdenum from a large number of elements of analytical importance has been developed. The method is based on the extraction of a Mo(V)-ferron (7-iodo-8-hydroxyquinoline-5-sulphonic acid) complex into trioctylamine-chloroform in a sulphuric acid medium using ascorbic acid as a reductant. Many elements such as Re(VII), W(VI), U(VI), Th(IV), Cr(III), Cr(VI), V(V), Ce(IV), Ru(III), Co(II), Ni(II), Mn(II), Fe(II), Fe(III), Cd(II), Mg(II), Cu(II), Al(III), Zn(II), Pb(II), Ag(I), and As(V) are not extracted under the conditions proposed and, thus, molybdenum can be easily separated without any interference. Sulphate, chloride, nitrate, phosphate, and oxalate anions have no effect on the extraction of molybdenum. However, zirconium and palladium interfere seriously. The ratio of Mo: ferron: TOA in the extracted species is found to be 1: 1: 3 using Job’s method of continuous variations. This value has been further confirmed by the mole-ratio method. The text was submitted by the authors in English.     

Thermogravimetric analysis of some metal thiocarbonates and sulphides obtained with potassium thiocarbonate (PTC) reagent

The thiocarbonates of K(I), Tl(I), Pb(II), Cd(II), Cu(II), Co(II), Ni(II), Zn(II), Fe(II) and the sulphides of Ag(I), Cu(II), Cd(II), Hg(II), Bi(III), Mo(VI), Pt(IV), Au(III), V(V), Se(IV), Te(IV), As(III, V), Sb(III) have been studied by thermogravimetric analysis. These studies not only confirm the purity of the precipitated products obtained with PTC but also determine correct temperature ranges for the precipitates to attain constant weight, thereby affording gravimetric evaluations of even mg quantities of the metal ions studied. Purity of precipitated products was made possible with the technique of precipitation from homogeneous solution based on the PTC reagent as precipitant.     

A fast and precise heterometric determination of thallium(I) with sodium tetraphenylborate

The heterometric titration of thallium(I) with sodium tetraphenylborate, at various pH values and in the presence of salts and different complexing agents, was studied; 1.5–0.75 mg of thallium(I) could be determined within 3–4 min, and the error was negligible. Of the complexing agents studied, sodium pyro- and tripolyphosphate had a specific influence, raising the sensitivity about 4-fold, and no interference was caused by the presence of 30–130-fold molar excesses of the following metals: Ca, Mg, Zn, Mn, Co, Ni, Fe(III), Al, UO₂(II), Cd, Cu(II), Pb, Bi(III), Ag, V(V), Mo(VI) W(VI) and Th. Pd, Au(III) and Pt(IV) did not interfere.     

Sorption-spectroscopy and test determination of uranium(VI) and iron(III) from a single sample on the solid phase of fiber materials filled with an AB-17 ion exchanger

Diffuse reflectance spectroscopy has been used for the study of the sorption of malonate and glycolate complexes of uranium(VI) and iron(III), present simultaneously in solution, onto the solid phase of fiber materials filled with an AB-17 anion exchanger. In the form of malonate complexes uranium(VI) is determined in 0.5 M HCl on substrate discs with immobilized Arsenazo III, while iron(III) is determined on substrate discs with potassium thiocyanate in 0.5 M HCl. The dependence of the analytical signals on the concentrations of U(VI) and Fe(III) is linear in the ranges 0.02–0.16 μg/mL; the detection limit is 0.01 μg/mL. The possibility of analysis of U(VI) and Fe(III) mixtures in ratio from 1: 5 to 5: 1 in the presence of 2-fold concentrations of Zr(IV), Th(IV), and Ti(IV), 5-fold concentrations of Bi(III), 10-fold concentrations of Cu(II), 20-fold concentrations of La(III), 100-fold concentrations of Ni(II) and Zn(II), and 200-fold concentrations of Co(II) and Ca(II) has been demonstrated. Standard color scales in the concentration range from 0.02 to 0.2 μg/mL have been used for the visual determination of uranium(VI) and iron(III).     

Luminol-K2S2O8体系中金属离子化学发光行为的研究

报导了在自行设计的流动注射式化学发光分析仪上,对Luminal-K2S2O8体系中32种金属离子的化学发光行为的系统研究.确定了对金属离子的最优测定条件以及大多数金属离子的检出极限和线性范围.     

Determination of uranium, iron, copper, and nickel from ore samples by MEKC using N,N'-ethylene bis(salicylaldimine) as complexing reagent

An analytical procedure has been developed for the separation of dioxouranium(VI), iron(III), copper(II), nickel(II), cobalt(II), cobalt(III), palladium(II), and thorium(IV) by MEKC using N,N'-ethylene bis(salicylaldimine) (H(2)SA(2)en) as a complexing reagent with total runtime <4.5 min. SDS was used as micellar medium at pH 8 with sodium tetraborate buffer (0.1 M). An uncoated fused-silica capillary with an effective length of 50 cm x 75 microm id was used with an applied voltage of 30 kV with photodiode array detection at 231 nm. Linear calibrations were obtained within 0.111-1000 microg/mL of each element with LODs within 37-325 ng/mL. The developed method was tested for analysis of uranium ore samples indicating its presence within 103-1789 microg/g with RSD within 0.79-1.87%. Likewise copper, nickel, and iron in their combined matrix were also simultaneously determined with RSD 0.4-1.6% (n = 6).     

Iron(II) titration of some metal ions, with oxazine dyes as redox indicators

The use of oxazine dyes as redox indicators in the determination of uranium(VI), copper(II), osmium(VIII), iridium(IV) and thallium(III) with iron(II) as reductimetric titrant in phosphoric acid medium has been investigated. The determination of copper in brass and the analysis of the binary mixtures of U(VI) and U(IV), and of Tl(III) and Tl(I) with this reductant and these indicators have been studied.