甲烷部分氧化制合成气:载体及助剂对Ni系催化剂活性的影响

 采用浸渍法制备了Ni系催化剂,并用程序升温还原和X射线衍射技术对催化剂进行了表征,用固定床微反装置考察了催化剂的催化活性．活性考察结果表明,在Ni担载量为8％的Ni／γ－Al2O3,Ni／δ－Al2O3,Ni／θ－Al2O3和Ni／α－Al2O3四种催化剂上,甲烷部分氧化制合成气反应的活性及产物选择性存在着明显的差异．在770℃下,甲烷转化率及CO和H2的选择性按Ni／γ－Al2O3＜Ni／δ－Al2O3＜Ni／θ－Al2O3≈Ni／α－Al2O3顺序排列．在相同的条件下,加入适量的CeO2助剂后,Ni／γ－Al2O3和Ni／δ－Al2O3上的反应活性和选择性显著提高,而Ni／θ－Al2O3和Ni／α－Al2O3上的活性和选择性却变化不大．同时,表征结果显示,Ni易与γ－Al2O3形成镍铝尖晶石NiAl2O4,加入CeO2助剂能有效地抑制该组分的生成,而Ni／α－Al2O3样品中未发现NiAl2O4．因此,不同Ni／Al2O3催化剂体系上的反应活性及选择性的差异可归结为不同结构Al2O3载体的性质不同,及CeO2对抑制镍铝尖晶石生成的效果不同．     

贵金属铂对镍基催化剂上萘转化性能的影响

 在常压连续流动固定床反应器上，以萘作为生物质气化气中焦油的模型化合物，研究了Pt对Ni／Al2O3催化剂上萘的转化率、CO和H2的选择性及收率的影响，比较了Ni－Pt／Al2O3和Ni／Al2O3两种催化剂上萘的水蒸气转化所产生的积碳量和副产物的种类，并初步考察了Ni－Pt／Al2O3催化剂上萘的水蒸气转化反应的动力学．     

稀土Ce对制合成气用Ce-Ni/Al2O3催化剂活性和稳定性的影响

 用浸渍法制备了Ni／Al2O3和Ce－Ni／Al2O3催化剂,并用BET,TGA－DTA和XPS技术对催化剂进行了表征,考察了稀土Ce对催化剂性能的影响,探讨了催化剂失活的原因．结果表明,在甲烷部分氧化和二氧化碳重整反应中,稀土Ce存在有部分还原变价过程（Ce4＋→Ce3＋）,不仅抑制了催化剂的积碳,而且改善了催化剂的水热稳定性和催化性能．经过较长时间反应的Ce－Ni／Al2O3催化剂,其比表面积下降,活性物种Ni和助剂Ce向体相迁移或部分流失,以及Ni晶粒的烧结聚集长大可能是造成催化剂逐渐失活的主要原因．     

加氢处理催化剂的制备和表征 Ⅰ.MoNiP/Al2O3催化剂的制备及助剂的作用

 采用专利方法制备出一种新型的γ－Al2O3,并以其为载体,制备出加氢处理催化剂MoNiP／Al2O3．用PAS－CA,XPS,DRS,TPR和微型反应色谱等技术对γ－Al2O3和催化剂进行了表征,考察了Ni和P两种助剂的作用．结果表明,γ－Al2O3具有较大的孔径,集中的孔分布和较高的机械强度;活性金属Mo在γ－Al2O3表面上的化学分散量（分散阈值）可达5．04～5．82μmol／m2．因而特别适合用作高活性加氢处理催化剂的载体．引入的Ni主要是同Mo／Al2O3催化剂表面上较稳定的金属－载体相互作用复合物反应,并生成类NiMoO4化合物;在MoNi／Al2O3催化剂中引入P,有利于抑制四面体配位结构的物种Mo［T］,增加八面体配位结构的物种Mo［O］,改善催化剂的还原性能,从而提高催化剂的加氢处理活性．助剂Ni和P的最佳含量分别为w（Ni）＝4．0％和w（P）＝2．6％．     

含钴铜镍类水滑石焙烧产物催化分解N2O的研究

 合成了含Co，Cu和Ni的M／Mg－Al－HTL类水滑石，并将其焙烧产物用于N2O催化分解反应．实验结果表明，Co／Mg－Al－HTL对N2O分解反应的催化活性明显高于Cu／Mg－Al－HTL和Ni／Mg－Al－HTL的活性．在保持样品中Al含量不变的条件下，催化活性随着Co含量的增加及Mg含量的减少而升高，各催化剂的活性顺序为：Co／Al－HTL＞Co／Mg－Al－HTL＞Cu／Mg－Al－HTL＞Ni／Mg－Al－HTL．在此基础上，进一步考察了Co／Al－HTL中Co／Al原子比调变对催化剂活性的影响．对含Co类水滑石及其焙烧产物进行了XRF，XRD和N2O－TPD表征．结果表明，含Co类水滑石具有典型的水滑石结构，其高温焙烧产物都含尖晶石相．由于尖晶石相中Co－O－Al活性中心的作用，含Co类水滑石对N2O分解反应表现出较高的催化活性．随着Co／Al原子比的增大，含Co类水滑石焙烧产物的尖晶石相特征更加突出，Co－O－Al活性中心数目随之增多，催化剂的活性也相应升高．     

红外光谱研究Pt-Re/Al2O3重整催化剂的表面结构

CO和NO吸附或两者竞争吸附在Pt／Al2O3，Re／Al2O3和Pt－Re／Al2O3催化剂上的红外光谱可以给出Pt和Re的表面结构信息．本文研究的催化剂为低金属载量的Pt／Al2O3，Re／Al2O3和工业型Pt－Re／Al2O3，其中Pt含量0．22％，Re含量0．43％（质量分数）．实验结果表明，用NO与CO双分子竞争吸附的红外光谱实验方法可分别表征还原态Pt－Re／Al2O3重整催化剂上Pt表面和Re表面，并视需要可对Pt表面和Re表面进行半定量分析．在还原态工业型Pt－Re／Al2O3重整催化剂表面上，没有明显迹象表明有Pt－Re合金形成．     

Al2O3／WO3／ZrO2固体强酸催化剂对正丁烷异构化的催化性能

 通过沉淀、回流、浸渍和焙烧等步骤制备了Al2O3／WO3／ZrO2固体强酸催化剂．采用XRD，N2吸附，UV－Vis光谱，NH3－TPD和H2－TPR等技术测定了Al2O3对WO3／ZrO2催化剂的结构、表面酸性、氧化还原性及正丁烷异构化反应性能的影响．结果表明，在WO3／ZrO2中引入适量的Al2O3对其表面酸强度及酸量无显著影响，但可使催化剂中的ZrO2组分以稳定的四方相形式存在，并能有效地抑制催化剂中WO3的聚集长大，从而提高催化剂的稳定性和正丁烷异构化的转化率和选择性．添加铂于Al2O3／WO3／ZrO2中可进一步提高其催化性能．还考察了催化剂的焙烧温度、Al含量、反应温度和反应气氛对正丁烷异构化反应的影响．     

甲烷干重整反应用Ni-Ru/MgAl类水滑石催化剂的研究

采用焙烧记忆法分别制备Ni/Mg Al O和NiRu/Mg Al O类水滑石催化剂用于甲烷干重整反应.利用XRD、TPR、TG、XPS、CO2-TPD、TEM等表征催化剂的结构及失活特征,发现在Ni/Mg Al O中添加Ru,有利于增加催化剂表面Ni含量,并促进Ni2+的还原.不同Mg/Al比双金属催化剂中,7Ni-0.15Ru/Mg2.5Al催化剂具有较高的催化活性,这归结为该催化剂适宜的碱性、较高表面Ni含量以及小尺寸的Ni0物种.添加Ru明显抑制Ni/Mg Al O催化剂表面的丝状碳的形成.而7Ni-0.15Ru/Mg2.5Al较强的抗积碳性能与其较小Ni0晶粒尺寸及适宜催化剂碱性有关.     

临氢水热处理对Ni/γ-Al_2O_3催化剂结构和性能的影响

采用浸渍法制备了Ni负载量为17%的Ni/γ-Al2O3催化剂.在氢气压力4 MPa,温度180℃条件下对Ni/γ-Al2O3催化剂进行了不同时间的水热处理.通过XRD、TG、H2-TPR和低温氮气物理吸附等手段对水热处理前后的催化剂进行表征,并考察其催化1,4-丁炔二醇加氢反应性能.结果表明,临氢水热处理导致载体γ-Al2O3水合相变为薄水铝石,随着水热处理时间的延长,薄水铝石的结晶度逐渐增大.γ-Al2O3的水合相变引起活性组分Ni晶粒的聚集及催化剂比表面积和孔容下降,从而导致催化剂活性降低.     

掺杂对Pd/Al2O3催化剂物相结构及表面氧性质的影响

采用XRD、DTA、TPD－MS及流动反应法等手段，研究了掺杂超细ZrO2对Pd／Al2O3催化剂物相结构、表面氧性能及催化活性的影响.结果表明，掺杂超细ZrO2，对催化剂Pd／Al2O3的载体物相变化（α－Al2O3的生成）有明显的抑制作用，很高了催化剂的贮氧能力及表面吸附氧的活性，从而提高了催化剂的耐热稳定性、氧化能力以及对贫氧气氛的适应能力．     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.