Benzothiazole-2-aldehyde-2-quinolylhydrazone as a reagent for the extractive spectrophotometric determination of copper (II)

Benzothiazole-2-aldehyde-2-quinolylhydrazone (BTAQH) was used for the spectrophotometric determination of trace amounts of copper(II) after the extraction process. Copper(II) reacts with BTAQH at pH 8.3–12.6 to form a water-insoluble 1:2 complex, which can be extracted with many kinds of organic solvent. The extracted species with benzene has an absorption maximum at 523 nm and obeyed Beer's law over the range 0.09 to 0.75 ppm of copper. The molar absorptivity is 7.50 × 10⁴M^?1 cm^?1 at 523 nm. The spectral properties of the copper(II) complexes with some tridentate hydrazones containing benzothiazole ring as a functional group were also discussed.     

Analysis of gasoline contaminated water samples by means of dopant-assisted atmospheric pressure photoionization differential ion mobility spectrometry

In this study the influence of aromatic dopant benzene on the sensitivity of GC-APPI-DMS to gasoline related aromatic compounds was investigated. This influence was investigated on example of four gasolin related fingerprints (toluene, ethylbenzene, o-xylene, and 1,2,4-trimethylbenzene), which were found in high relative abundance in the water-soluble gasoline fraction. The analysis of calibration curves slopes demonstrats that the GC-APPI-DMS sensitivity to gasoline fingerprints can be improved by up to seven times when benzene concentration in nitrogen carrier gas is less than 10 ppm_v/v. The estimated detection limits (S/N?=?3) for the analyzed in this study compounds were found to be within the range of 33–105 μg L^?1 at benzene concentration in the carrier gas of 2.27 ppm_v/v (10 μL injection volume). These limits of detection may be reduced (at the cost of lower resolution) using the larger injection volumes. For example, increase of injection volume to 100 μL at benzene concentration in the carrier gas of 2.27 ppm_v/v leads to reduction of LOD values for toluene, ethylbenzene, and o-xylene to 11.1, 13.3, and 5.3 μg L^?1, respectively.     

The nature of the lowest excited state and photosubstitution reactivity of tetracarbonyl-1,10-phenanthrolinetungsten(0) and related complexes

Absorption and emission spectral studies of M(CO)₄L complexes (M = Cr Mo, W; L = 2,2′-bipyridine, 1,10-phenanthroline, 5-CH₃-, 5-Cl-, 5-Br-, 5-NO₂-1,10-phenanthroline) have been carried out and reveal that the lowest excited state in every case is charge-transfer (CT) in character, M→ CT in absorption, and in no case do the ligand field (LF) excited states cross below the CT state. Minimum energies of the LF states have been established by the spectroscopic study of cis-bis(pyridine)- and cis-bis(aliphatic amine)-tetracarbonylmetal(0) complexes which all have LF lowest excited states for M = Mo, W. For the M(CO)₄L complexes emission is detectable for M = Mo or W and occurs in the range 14.40-15.66 kK with lifetimes of 7.9-13.3 μsec and quantum yields of 0.02–0.09 all in EPA solution at 77 K. For the bis-pyridine and -aliphatic amine complexes emission occurs only from the W complexes and is of the order of 3.0–4.0 kK higher in energy than for the M(CO)₄L complexes. Photosubstitution of pyridine is efficient in cis-W(CO)₄(py)₂ (py = pyridine): Φ_436nm = 0.23; Φ_405nm = 0.27; and Φ_366nm = 0.23. The M(CO)₄L complexes have strongly wavelength dependent, but modest, quantum yields for CO substitution and show that the lowest CT state is unreactive. Typical values for CO substitution for M = W and L = 1,10-phenanthroline are: Φ_436nm = 1.6 × 10^?4; Φ_405nm = 1.2 × 10^?3; Φ_366nm = 9.2 × 10^?3; and Φ_313nm = 2.2 × 10^?2.     

Investigation of the Benzene–Naphthalene and Naphthalene–Naphthalene Potential Energy Surfaces: DFT/CCSD(T) Correction Scheme

The potential energy surfaces of the naphthalene dimer and benzene–naphthalene complexes are investigated using the recently developed DFT/CCSD(T) correction scheme [J. Chem. Phys. 2008 , 128, 114 102]. One and three minima are located on the PES of the benzene–naphthalene and the naphthalene dimer complexes, respectively, all of which are of the parallel‐displaced type. The stabilities of benzene–naphthalene and the naphthalene dimer are ?4.2 and ?6.2 kcal mol^?1, respectively. Unlike the benzene dimer, where the T‐shaped complex is the global minimum, the lowest‐energy T‐shaped structure is about 0.2 and 1.6 kcal mol^?1 above the global minimum on the benzene–naphthalene and the naphthalene dimer potential energy surfaces, respectively.     

Kinetics and mechanism of promoted hydrolysis of 4‐nitrophenyl acetate by zinc(II)‐tripod: Different roles of mononuclear and trinuclear species

Coordination studies on Zn(II) complexes of 1,3,5‐tri(2,5‐diazahexyl)benzene (L) show that by comparison with the non‐deprotonation of complex ZnL in a 1:1 system, the three‐dimensional complexiaton decreases the pK_a of the Zn‐bound water molecule, that is, pK_a = 7.47 for trinulclear complex Zn₃L in a 3:1 metal–ligand ratio. These two types of zinc(II) complexes have been examined as catalysts for the hydrolysis of 4‐nitrophenyl acetate (NA) in 10% (v/v) CH₃CN at 298 K, I = 0.10 mol dm^?3 KNO₃ at pH range 6.5–8.2 and 8.5–10, respectively. Kinetic studies show that the second‐order rate constants of NA‐hydrolysis catalyzed by complexes ZnL, Zn₃L, and Zn₃LH_?1 are 0.021, 0.0082, and 0.342 mol^?1 dm³ s^?1, respectively. In all the cases, the pH‐dependent observed first‐order rate constant, k_obs, shows sigmoidal pH–rate profile. The 1:1 complex ZnL–H₂O undergoes NA hydrolysis by direct rate‐determining hydrolysis to produce 4‐nitrophenol(ate) (NP^?) and ZnL(OOCCH₃); while in the 3:1 system the oxygen atom of acetic group forms a H‐bond with the Zn(II)‐bound water of the second branch of tripod indicating that the polynuclear centers are associated and bi‐functional. © 2003 Wiley Periodicals, Inc. Int J Chem Kinet 36: 41–48 2004     

Simultaneous Determination of Clopidogrel and Its Carboxylic Acid Metabolite (SR26334) in Human Plasma by LC–ESI–MS–MS: Application to the Therapeutic Drug Monitoring of Clopidogrel

A sensitive and specific liquid chromatography-tandem-mass spectrometry method was developed and validated for the simultaneous determination of clopidogrel and its carboxylic acid metabolite (SR26334) in human plasma using nateglinide and pioglitazone as internal standards. Analytes were extracted from 0.50 mL of plasma using diethyl ether–n-hexane (4:1, v/v). Chromatographic separation was performed on a Teknokroma C₁₈ column with a mobile phase of methanol–water (containing 0.1% formic acid) (80:20, v/v) at a flow rate of 0.20 mL min^?1 within 5.6 min. Linearity was established over the concentration range of 0.005–5 ng mL^?1 for clopidogrel and 20–2,500 ng mL^?1 for SR26334. Intra- and inter-batch standard deviations were less than 9.2% and the accuracy of this assay was found to fall within an acceptable range ≤10.0%. The method was successfully applied to the therapeutic drug monitoring of clopidogrel.     

Solvent extraction and spectrophotometric determination of iron(II) with 2,2′-dipyridyl-2-furancarbothiohydrazone

2,2′-Dipyridyl-2-furancarbothiohydrazone (DPFTH) was used for the spectrophotometric determination of trace amount of iron(II) after the extraction process. Iron(II) can be quantitatively extracted with DPFTH in benzene from aqueous solution buffered to 3.0–8.0. The extracted species has absorption maxima at 440, 477, and 738 nm and obeyed Beer's law over the range 0–40 μg of iron in 10 ml at 738 nm. The molar absorptivity at this wave length is 1.17 × 10⁴ liters mole^?1 cm^?1. The proposed method is relatively selective for iron(II) and is satisfactorily applied to the determination of the total iron in natural waters. The proton dissociation constants of the ligand determined spectrophotometrically were pK_a1 = 2.88 and pK_a1 = 6.70 at 25 °C and μ = 0.1.     

Inclusion complexes of Schiff bases as phytogrowth inhibitors

This article details the preparation, characterization and phytotoxic evaluation of several Schiff base inclusion complexes obtained from β-cyclodextrin and p-sulfonic acid calix[6]arene. The inclusion complexes (1:1 molar ratio) were prepared by mixing a 5 mmol L^?1 aqueous solution (containing 1 % DMSO) of Schiff bases (guests) with aqueous solution (containing 1 % DMSO) of 5 mmol L^?1 of β-cyclodextrin or p-sulfonic acid calix[6]arene (hosts). The host–guest systems were characterized via a series of NMR experiments. The ability of the complexes to interfere with the radicle elongation of Sorghum bicolor (dicotyledonous species) and Cucumis sativus (monocotyledonous species) was evaluated. After 48 h, the inclusion complexes inhibited the radicle elongation of both species from 11 to 56 %. The formation of inclusion complexes was also investigated theoretically by molecular dynamics simulations in aqueous solution through implicit approach. Based on the experimental observation, the phytotoxic activity evaluated can be attributed to the formation of host–guest systems. This was supported by the theoretical findings based on stable interaction energy analyses for all the studied supramolecular systems.     

Synthesis,characterization, and insulin-enhancing studies of unsymmetrical tetradentate Schiff-base complexes of oxovanadium(IV)

A series of unsymmetrical tetradentate Schiff bases were synthesized by interaction of 2-hydroxy-1-naphthaldehyde, phenylenediamine and salicylaldehyde, or substituted salicylaldehyde in an ethanolic medium. The oxovanadium(IV) complexes and the ligands were synthesized and characterized by elemental analyses, ¹H NMR, infrared, electron paramagnetic resonance, electronic spectra, cyclic voltammetry, and room temperature magnetic susceptibility measurements. The elemental analyses for both the ligands and the metal complexes confirmed purity of the compounds as formulated. Electron paramagnetic resonance spectra of the complexes were measured as powder and in toluene/dichloromethane (9 : 1, v/v) solution at room and liquid N₂ temperatures. The g values, g _o = 1.971, g _⊥ = 1.978, and g = 1.950, are the same for all the complexes examined. The vanadium nuclear hyperfine splitting, A _o = 101–99, A _⊥ = 65–64, A _∥ = 179–177, vary slightly with substituents on the salicylaldehyde. Infrared spectra reveal strong V=O stretching bands in the range 970–988 cm^?1, typical of monomeric five-coordinate complexes. The room temperature magnetic moments of 1.6–1.8 BM for the complexes confirmed that the complexes are V(IV) complexes, with d¹ configuration. Only one quasi-reversible wave is observed for each compound and they all showed redox couples with peak-to-peak separation values (ΔE _p) ranging from 78 to 83 mV, indicating a single step one electron transfer process. Insulin-mimetic tests on C2C12 muscle cells using Biovision glucose assay showed that all the complexes significantly stimulated cell glucose utilization with negligible cytotoxicity at 0.05 µg µL^?1.     

Spektrophotometrische Mikrobestimmung von Chlorid als Hexachloroferrat(III)-komplex in Blutserum und anderen Körperflüssigkeiten

The method is based on the formation of hexachloroferrate(III) complexes, which are characterized by an absorption maximum in the range of 348 nm. The advantages are: simplicity of the procedure, no protein precipitation necessary; small quantities needed; little time consuming; constant and reproducible results; high sensitivity. The absorbance for 0.1 μEq Cl^?/ml testing solution is about 0.255. Lambert-Beer's law is obeyed in the range of 0.01–0.6 μEq Cl^?/ml testing solution. The error is about ± 2.5%. A comparison with other methods for the determination of chloride is given.     

Spectrophotometric and solvent extraction studies of metal complexes of some hydrazones

Complex formation of o-hydroxybenzaldehyde isonicotinoyl-hydrazone with Co(II), Ni(II), Zn(II), Mn(II), and Cd(II) has been investigated. These complexes are soluble in water-dioxane 1:1 (v/v) solutions and they were studied spectrophotometrically. The same complexes are soluble in organic solvents and studies on their extraction with chloroform, 1-pentanol and 1-octanol, for possible analytical application, are reported. In addition, complex formation of o-hydroxybenzaldehyde benzoyl hydrazone with Zn(II), and Mn(II) is also reported.     

Simultaneous Quantitation of Paracetamol, Pseudoephedrine and Chlorpheniramine in Dog Plasma by LC-MS-MS

A simple, rapid and sensitive liquid chromatography/electrospray tandem mass spectrometry quantitative detection method, using amantadine as internal standard, was developed for the simultaneous analysis of paracetamol, pseudoephedrine and chlorpheniramine concentrations. Analytes were extracted from plasma samples by liquid–liquid extraction with n-hexane–dichloromethane–2-propanol (2:1:0.1, v/v), separated on a C18 reversed-phase column with 0.1% formic acid–methanol (40:60, v/v) and detected by electrospray ionization mass spectrometry in positive multiple reaction monitoring mode. Calibration curves for plasma were linear over the concentration range 10–10,000 ng mL^?1 of paracetamol, 2–2,000 ng mL^?1 of pseudoephedrine and 0.2–200 ng mL^?1 of chlorpheniramine. The method has a lower limit of quantitation of 10 ng mL^?1 for paracetamol, 2.0 ng mL^?1 for pseudoephedrine and 0.2 ng mL^?1 for chlorpheniramine. Recoveries, precision and accuracy results indicate that the method was reliable within the analytical range, and the use of the internal standard was very effective for reproducibility by LC-MS-MS. This method is feasible for the evaluation of pharmacokinetic profiles of a novel multicomponent sustained release formulation containing 325 mg of paracetamol, 30 mg of pseudoephedrine hydrochloride and 2 mg of chlorpheniramine maleate. It is the first time the pharmacokinetic evaluation of a novel sustained-action formulation containing paracetamol, pseudoephedrine and chlorpheniramine has been elucidated in vivo using LC-MS-MS.     

Static and dynamic properties of anionic intermolecular aggregates: the I−–benzene–Ar n case

Molecular dynamics simulations on the I^?–benzene–Ar _n clusters have been carried out using an atom(ion)-bond model to describe the nonelectrostatic contribution to the total interaction. Results for I^?–benzene–Ar and I^?–benzene–Ar _n (n = 3, 18 and 25) are presented and some predicted properties are compared with those of the alkali cation–benzene clusters solvated by Ar atoms.     

Extraction and spectrophotometric determination of niobium by tetraphenylarsonium and phosphonium chloride from a hydrochloric acid solution

The extraction of niobium(V) in the form of a chloro complex has been studied. Radiometrical and spectrophotometrical studies show that niobium(V) is extracted practically completely from a solution containing more than 9 mol dm^?3 chloride in the range of 2–5 M hydrogen ion concentration by chloroform solutions of tetraphenylarsonium (TPA) and tetraphenylphosphonium (TPP) chloride and that niobium is not extracted at chloride concentrations less than 6 mol dm^?3. The mechanism of extraction is based on the formation of the ion-associated compounds that form between the onium cation and the oxotetra-chloroniobate(V) anion. The extracted complexes in chloroform have a maximum absorbance at 282 nm (TPA) and 285 nm (TPP); they obey Beer's law in the range of 1–10 μg Nb ml^?1, and are stable for at least 24 hr. The molar absorptivity of the method is 1.33 × 10⁴ dm³ mol^?1cm^?1. The composition of the extracted species [(C₆H₅)₄X] [NbOCl₄] where X = As or P was determined spectrophotometrically, radiometrically, and by characterization of the crystalline compounds isolated.     

Liquid–Liquid–Liquid Micro Extraction Combined with CE for the Determination of Rare Earth Elements in Water Samples

A simple method for determination of rare earth elements (REEs) by liquid–liquid–liquid microextraction (LLLME) coupled with capillary electrophoresis and ultraviolet technique was developed. In the LLLME system, 40 mmol L^?1 4-benzoyl-3-methy-1-phenyl-5-pyrazolinone (PMBP) acted as extractant and 4% (v/v) formic acid was used as back-extraction solution. The parameters influencing the LLLME, including the type of the organic solvent, sample pH, formic acid concentration, PMBP concentration, extraction time, volume of organic solvent, stirring rate and phase volume ratio, were investigated. Under the optimized conditions, the detection limits (S/N = 3) of REEs were in the range of 0.19–0.70 ng mL^?1. The developed method was successfully applied to the determination of trace amounts of REEs in water samples.     

Copper(II) and Zinc(II) Complexes of Conformationally Constrained Polyazamacrocycles as Efficient Catalysts for RNA Model Substrate Cleavage in Aqueous Solution at Physiological pH

As part of a quest for efficient artificial catalysts of RNA phosphodiester bond cleavage, conformationally constrained mono‐ and bis‐polyazamacrocycles in which tri‐ or tetraazaalkane chains link the ortho positions of a benzene ring were synthesized. The catalytic activities of mono‐ and dinuclear copper(II) and zinc(II) complexes of these polyazamacrocycles towards cleavage of the P?O bond in 2‐hydroxypropyl‐4‐nitrophenylphosphate (HPNP) in aqueous solution at pH 7 have been determined. Only the complexes of the ligands incorporating three nitrogen atoms in a macrocycle proved to be capable of efficiently catalyzing HPNP transesterification. The dinuclear complexes were found to be approximately twice as efficient as their mononuclear counterparts, and exhibited Michaelis–Menten saturation kinetics with calculated rate constants of k_cat≈10^?4 s^?1. By means of quantum chemical calculations (DFT/COSMO‐RS), several plausible reaction coordinates were described. By correlating the calculated barriers with the experimental kinetic data, two possible reaction scenarios were revealed, with activation free energies of 20–25 kcal mol^?1.     

Tungsten(V) dimeric complexes with heterocyclic dithiocarbamates

In this paper we report the syntheses and study of a number of oxo- and sulphido-bridged tungsten(V) complexes with morpholine dithiocarbamate and piperidine dithiocarbamate as ligands. We assign the following formulae to the complexes: W₂O₃(Rdtc)₄, W₂O₄(Rdtc)₂, W₂O₂S₂(Rdtc)₂ and W₂O₃S(Rdtc)₂ (where R = morpholine and piperidine), based on the analytical data. We have studied the complexes by IR and electronic spectra, and magnetic susceptibility measurements. We assign in the IR spectra the following bands: W=O (ν_s=939–948 cm^?1), W-O_b(ν_a=813–819 cm^?1, ν_s = 431–448 cm^?1), W-S_b (ν_a=470–476 cm^?1, ν_s = 368–370 cm^?1, C-N (β = 1511–1519 cm^?1) and C-S (ν = 1090–1113 cm^?1). The low values of the magnetic moments (0.03–0.60 B.M.) are in accordance with a dimeric species of tungsten(V).     

Development and Validation of an RP–LC–UV Method for the Determination of Ondansetron: Application to Pharmaceutical Dosage Forms

A new, simple, rapid, sensitive and specific isocratic RP–LC–UV method was developed and validated for the determination of ondansetron in pharmaceutical dosage forms of orally disintegrating tablets, oral solution and injection. The LC separation was achieved on a Hypersil C4 column (250 × 4.6 mm, 5 μm) using a mobile phase of 50 mM potassium dihydrogen phosphate anhydrous adjusted to pH 3.5 with orthophosphoric acid and acetonitrile (30:70, v/v) at a flow rate of 1.0 mL min^?1 and UV detection at 310 nm. The method was validated for specificity, linearity, precision, accuracy, limit of quantification, limit of detection, robustness and solution stability. The calibration curve was linear over a concentration range of 100–1,000 ng mL^?1 (r ²  = 0.9996) with limit of detection and limit of quantification 50 and 100 ng mL^?1, respectively. The intra-day and inter-day precision and accuracy were between 0.79 and 2.37% and ?0.64 and 1.65%, respectively. The method was successfully applied for analysis of ondansetron in the presence of excipients in commercially available pharmaceutical dosage forms.     

Equilibrium Studies of Dibutyltin(IV)–Zwitterionic Buffer Complexation

Equilibrium studies in aqueous solution are reported for dibutyltin(IV) (DBT) complexes of the zwitterionic buffers “Good’s buffers” Mes and Mops. Stoichiometric and formation constants of the complexes formed were determined at different temperatures and ionic strength 0.1 mol·L^?1 NaNO₃. The results show that the best fit of the titration curves were obtained when the complexes ML, MLH_?1, MLH_?2 and MLH_?3 were considered beside the hydrolysis product of the dibutyltin(IV) cation. The thermodynamic parameters ΔH ^o, ΔS ^o and ΔG ^o calculated from the temperature dependence of the formation constant of the dibutyltin(IV) complexes with 2-(N-morpholino)ethanesulfonic acid (Mes) and 3-(N-mor-pholino)-propanesulfonic acid (Mops) were investigated. The effect of dioxane as a solvent on the formation constants of DBT–Mes and DBT–Mops complexes decrease linearly with the increase of dioxane proportion in the medium. The concentration distribution of the various complexes species was evaluated as a function of pH.