Preparation and Characterization of Mixed‐Valent Nickel Oxide/Nickel Hexacyanoferrate Hybrid Films and Their Electrocatalytic Properties

Polynuclear mixed‐valent nickel oxide and nickel hexacyanoferrate hybrid film was prepared on glassy carbon electrode by multiple scan cyclic voltammetry. The film growth was monitored using electrochemical quartz crystal microbalance (EQCM). The cyclic voltammogram of the nickel hexacyanoferrate film is characterized by single redox couple whereas nickel oxide/nickel hexacyanoferrate hybrid film exhibits two redox couples. Cyclic voltammetric features suggest that the charge transfer process in both films resembles that of surface‐confined redox species. In stronger basic solution (pH ≥9), nickel hexacyanoferrate film was gradually converted into nickel oxide film during potentiodynamic cycling. The peak potential of nickel oxide redox couple moved into more negative side with increasing pH of contacting solution whereas the peak potential of nickel hexacyanoferrate redox couple remains the same. Electrocatalytic behavior of hybrid film coated electrodes toward ascorbic acid, hydrazine and hydroxylamine was investigated using cyclic voltammetry technique. Analytical application of nickel oxide/nickel hexacyanoferrate hybrid film electrode was tested in amperometry and flow injection analysis.     

Preparation, Electrochemical Behavior and Electrocatalytic Activity of a Copper Hexacyanoferrate Modified Ceramic Carbon Electrode

A copper hexacyanoferrate modified ceramic carbon electrode （CuHCF/CCE） had been prepared by two-step sol-gel technique and characterized using electrochemical methods. The resulting modified electrode showed a pair of well-defined surface waves in the potential range of 0.40 to 1.0 V with the formal potential of 0.682 V （vs. SCE） in 0.050 mol·dm^-3 HOAc-NaOAc buffer containing 0.30 mol·dm^-3 KCl. The charge transfer coefficient （a） and charge transfer rate constant （ks） for the modified electrode were calculated. The electrocatalytic activity of this modified electrode to hydrazine was also investigated, and chronoamperometry was exploited to conveniently determine the diffusion coefficient （D） of hydrazine in solution and the catalytic rate constant （kcat）. Finally, hydrazine was determined with amperometry using the resulting modified electrode. The calibration plot for hydrazine determination was linear in 3.0 × 10^-6--7.5 × 10^-4 mol·dm^-3 with the detection limit of 8.0 × 10^-7 molodm^-3. This modified electrode had some advantages over the modified film electrodes constructed by the conventional methods, such as renewable surface, good long-term stability, excellent catalytic activity and short response time to hydrazine.     

Preparation and characterization of nickel hexacyanoferrate films for the removal of cesium ion by electrically switched ion exchange (ESIX)

The method of electrically switched ion exchange (ESIX) involves the sequential application of reduction and oxidation potentials to an ion exchange film to induce the respective loading and unloading of Cs⁺. In this study, four films of nickel hexacyanoferrate were prepared on nickel electrodes with different preparation procedures. Films were characterized by SEM/EDX. Each film shows a different performance with regard to Cs⁺ separation. Scanning electron microscopy was used to characterize the modified film surfaces. Cyclic voltammetry was used to investigate the ion exchange capacity and stability. The four films show a better capacity for Cs⁺ separation compared to previous methods for the deposition of ESIX films. An optimal nickel hexacyanoferrate film was generated when using an applied potential of 0.2 V relative to a saturated calomel electrode (SCE) to generate the nucleation sites, followed by a 1.3 V vs. SCE potential during the growth stage of the film. This film demonstrated the highest film capacity for ion exchange initially (17.3 × 10^?3 C cm^?2) and again after 1000 cycles (11.1 × 10^?3 C cm^?2).     

Copper hexacyanoferrate multilayer films on glassy carbon electrode modified with 4-aminobenzoic acid in aqueous solution

4-Aminobenzoic acid (4-ABA) was covalently grafted on a glassy carbon electrode (GCE) by amine cation radical formation during the electrooxidation process in 0.1 M KCl aqueous solution. X-ray photoelectron spectroscopy (XPS) measurement proves the presence of 4-carboxylphenylamine on the GCE. Electron transfer processes of Fe(CN)₆³⁻ in solutions of various pHs at the modified electrode are studied by both cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). Changing the solution pH would result in the variation of the terminal group's charge state, based on which the surface pK_a values were estimated. The copper hexacyanoferrate (CuHCF) multilayer films were formed on 4-ABA/GCE prepared in aqueous solution, and which exhibit good electrochemical behavior with high stability.     

Cu(II) Hexacyanoferrate(III) Modified Carbon Paste Electrode; Application for Electrocatalytic Detection of Nitrite

Copper hexacyanoferrate (CuHCF) film‐modified carbon paste electrode (CPE) has been prepared from various electrolytic aqueous solutions using consecutive cyclic voltammetry. The cyclic voltammograms showed the direct deposition of CuHCF films from the mixing of Cu²⁺ and Fe(CN)₆^3? ions and each time with one of the six cations: H⁺, Na⁺, K⁺, NH₄⁺, Mg²⁺, and Al³⁺. The CuHCF film showed a single redox couple that exhibited a cation effect (Na⁺, K⁺, Mg²⁺, and NH₄⁺) and anion effect (Cl^?, NO₃^?, SO₄^2?, ClO₄^?, and BrO₃^?) in the cyclic voltammograms. Voltammetric studies have indicated that in presence of nitrite, the cathodic peak current of CuHCF increases, followed by a decrease in the corresponding anodic current. This indicated that nitrite was reduced by the redox mediator immobilized on the electrode surface via an electrocatalytic mechanism. The process of reduction and its kinetics were investigated by using cyclic voltammetry, differential pulse voltammetry, chronoamperometry and chronocoulometry techniques. The electrocatalytic ability about 800 mV can be seen. The rate constant of the catalytic reduction of nitrite was found to be 7.9×10⁵ cm³ mol^?1 s^?1. Linearity range obtained was 5×10^?5?8.4×10^?3 by cyclic voltammetry and 8×10^?6?1.3×10^?3 and 4×10^?3?2×10^?2 by differential pulse voltammetry.     

Ferricyanide Confined in a Protonated Amine-Functionalized Silica Film on Gold: Application to Electrocatalytic Sensing of Nitrite Ions

An amine-functionalized porous sol–gel silica film was shown to be an effective platform to immobilize small anionic redox mediators of high solubility on solid electrodes by electrostatic interaction. The highly soluble mediator hexacyanoferrate was used as a model. The film was grown and firmly anchored on a gold electrode surface via thiol groups of a self-assembled monolayer of (3-mercaptopropyl)trimethoxysilane. Film growth and thickness were controlled by electrochemical modulation of pH at the electrode/solution interface in a sol of a hydrolyzed solution of tetraethoxysilane and 3-[2-(2-aminoethylamino)ethylamino]propyltrimethoxysilane by the application of a negative potential to the electrode. Protonation of the amine groups made the amine-functionalized surface useful to immobilize hexacyanoferrate on gold. Thus, the immobilization is pH dependent, being highly effective in strongly acidic medium. Cyclic voltammetry and scanning electron microscopy were used to characterize the film and to optimize the experimental conditions. The stability of the film was demonstrated by applying the catalytic properties of the hexacyanoferrate containing surface for nitrite sensing using a flow injection analysis (FIA) system. Under the optimized conditions, the sensor exhibited high sensitivity, low detection limit, easy handling, and stability with a linear range from 1.0 to 40.0?µmol?L^?1 and a detection limit of 0.53?µmol?L^?1 based on a signal-to-noise ratio of 3. The sensor was successfully applied to nitrite determination in water samples using FIA with excellent recoveries.     

Electrocatalytic Oxidation of Dopamine at Sol‐Gel Carbon Composite Electrode Chemically Modified with Copper Hexacyanoferrate

An organic‐inorganic composite electrode was prepared by the sol‐gel method. For this purpose the carbon composite electrode (CCE) was modified with copper hexacyanoferrate (CuHCF). The CuHCF‐CCE was prepared by two methods. In one method CCE was prepared in one step and in another method the electrode was prepared in a two‐step process. The electrochemical behavior of the CuHCF modified electrode was studied by cyclic voltammetry; the modified electrode shows a pair of peaks with a surface‐confined characteristic in a 0.1 M phosphate buffer (pH 7) with K⁺ cation, as a supporting electrolyte. The CuHCF‐CCE showed electrocatalytic activity toward oxidation of Dopamine (DA). The kinetics of the catalytic reaction was investigated by using chronoamperometry. The average value of the rate constant for catalytic reaction and the diffusion coefficient were calculated. At a 0.85 V potential under hydrodynamic conditions (stirred solution), the oxidation current is proportional to the dopamine concentration, and the calibration plot was linear over the concentration range of 5‐85 μM.     

Electrochemical Characterization of and Stripping Voltammetry at Screen Printed Electrodes Modified with Different Brands of Multiwall Carbon Nanotubes and Bismuth Films

A screen-printed electrode sensor has been fabricated by modifying the carbon ink surface with different brands of multiwall carbon nanotubes (MWCNTs) and bismuth film (BiF) for the determination of traces of lead, cadmium and zinc ions by square wave anodic stripping voltammetry. The MWCNTs, from three different sources, were functionalized and dispersed in Nafion (MWCNT-Nafion) solution and placed on screen printed electrodes (MWCNT-Nafion/SPE); bismuth films were then prepared by ex-situ plating of bismuth onto the MWCNT-Nafion/SPE electrodes. The electrochemical characteristics of BiF/MWCNT-Nafion/SPE/ were examined by electrochemical impedance spectroscopy and showed differences; the charge transfer resistance tends to decrease with negative applied potentials. After optimizing the experimental conditions, the square-wave peak current signal is linear in the nmol L^?1 range. The lowest limit of detection found for the separate determination of lead, cadmium and zinc were 0.7 nmol L^?1, 1.5 nmol L^?1, and 11.1 nmol L^?1, respectively, with a 120 s deposition time.     

A study of the electrocatalytic oxidation of methanol on a nickel–salophen-modified glassy carbon electrode

Nickel–salophen-modified glassy carbon electrodes prepared by transferring one drop of Ni–salophen complex solution on the electrode surface. This modified electrode has been used for the electrocatalytic oxidation of methanol in alkaline solutions with various methods such as cyclic voltammetry, chronoamperometry, and electrochemical impedance spectroscopy. The electrooxidation was observed as large anodic peaks, and early stages of the cathodic direction of potential sweep around 20 mV vs. Ag|AgCl|KCl_sat. A mechanism based on the electrochemical generation of Ni (Ш) active sites and their subsequent consumptions by methanol have been discussed. EIS studies were employed to unveil the charge transfer rate as well as the electrical characteristics of the catalytic surface. For the electrochemical oxidation of methanol at 5.0 M concentration, charge transfer resistance of nearly 0.936 kΩ was obtained, while the resistance of the electrocatalyst layer was about 111.6 Ω.     

Copper oxide-modified glassy carbon electrode prepared through copper hexacyanoferrate–G5-PAMAM dendrimer templates as electrocatalyst for carbohydrate and alcohol oxidation

We describe the modification of a glassy carbon electrode by electro-deposition of copper hexacyanoferrate (CuHCF) in the presence of an amine-terminated dendrimer (PAMAM) as a template. The electrode containing the CuHCF template was cycled in alkaline solution to generate a layer of cupric oxide (CuO). The mechanism of the formation of CuO and its electrocatalytic activity were investigated by cyclic voltammetry. Scanning electron microscopy reveals that the CuO prepared by this method has a meso-porous grid-like appearance. The formation of CuO was identified by XPS analysis of the modified electrode. The ability of the CuHCF film towards the electrocatalytic oxidation of carbohydrates and alcohols was detected using cyclic voltammetry. The over-potential required for carbohydrate and alcohol oxidation is lowered by ~400 mV compared to other chemically modified electrodes reported in the literature. Simple methodology has been adopted in this work for the preparation of the catalytically active electrode, and this work also explains the structure directing effect of dendrimer and its influence on the electrocatalytic oxidation of analytes.     

Electrocatalytic oxidation of L-tryptophan using copper hexacyanoferrate film modified gold nanoparticle graphite-wax electrode

A novel copper hexacyanoferrate (CuHCF) film modification on cysteamine (Cys)-gold nanoparticle (AuNp) graphite-wax (GW) composite electrode was achieved for the quantitative determination of L-Tryptophan (L-Trp) at a reduced overpotential of 400mV in comparison with the bare Cys-AuNp-GW composite electrode. This modified electrode exhibited a well resolved pair of redox peaks corresponding to the hexacyanoferrate (II/III) reactions of CuHCF film at a formal potential of 0.65 V at a scan rate of 20 mV s(-1). Electrochemical impedance spectroscopy (EIS) studies with the modified electrode showed a very low charge transfer resistance to the electron transfer kinetics of Fe(II)/Fe(III) reactions. A linear range of 8.5×10(-7) M to 1.2×10(-4) M with a detection limit of 1.85×10(-8) M was achieved for the determination of L-Trp with a sensitivity of 0.1198 μA/μM. The influence of ultrasonication on the stability of the CuHCF film modified electrode was investigated. In addition, the CuHCF film modified electrode displayed an excellent reproducibility towards the real time analysis of L-Trp in commercial milk samples.     

Preparation and Characterization of Mixed‐Valent Osmium Hexacyanoferrate/Silicomolybdate Hybrid Films and Their Electrocatalytic Properties

A polynuclear mixed‐valent osmium hexacyanoferrate/silicomolybdate film electrode has been prepared using repetitive cyclic voltammetry. The cyclic voltammograms have been recorded for the deposition of a mixed‐valent osmium hexacyanoferrate/silicomolybdate hybrid film directly from the mixture of Os³⁺, Fe(CN₆)^3?, and SiMo₁₂O₄₀^4? ions from the acidic aqueous solutions. The polynuclear mixed‐valent osmium hexacyanoferrate/silicomolybdate film exhibited four redox couples. The electrocatalytic properties of the osmium hexacyanoferrate/silicomolybdate film electrode have been studied. The modified electrode has shown good electrocatalytic properties towards the oxidation of dopamine, ascorbic acid, epinephrine, norepinephrine, and reduction of IO₃^?, Fe³⁺.     

A novel photoelectrochemical hydrogen peroxide sensor based on nickel(II)-potassium hexacyanoferrate-graphene hybrid materials modified n-silicon electrode

A platinum (Pt) film coated n-silicon (Pt/n-n⁺-Si) was modified with nickel(II)-potassium hexacyanoferrate (NiHCF)-graphene sheets (GS) hybrid and used as a photo-electrochemical (PEC) sensor for non-enzyme hydrogen peroxide (H₂O₂) detection. A NiHCF film was deposited on the surface of GS/Pt/n-n⁺-Si electrode by chemical method. The structure and composition of the NiHCF film was characterized by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). PEC behavior of the NiHCF-GS/Pt/n-n⁺-Si electrode was investigated using cyclic voltammetry (CV) under illumination. The modified electrode has been used as PEC sensor for H₂O₂ detection with a linear range of 2.0 × 10^?6–2.9 × 10^?3 M and a detection limit of 1.0 × 10^?6 M at a signal-to-noise ratio of 3 in a two-electrode cell with a Pt plate as counter electrode. The characteristics of GS layer have been discussed in both the improvement of sensibility and selectivity.     

Electrostatic spray deposition of graphene nanoplatelets for high-power thin-film supercapacitor electrodes

Thin-film electrodes of graphene nanoplatelets (GNPs) were fabricated through the electrostatic spray deposition (ESD) technique. The combination of a binder-free deposition technique and an open pore structure of graphene films results in an excellent power handling ability of the electrodes. Cyclic voltammetry measurements of 1-μm-thick electrodes yield near rectangular curves even at a very high scan rate of 20 V s^?1. Thin-film electrodes (1 μm thickness) show specific power and energy of about 75.46 kW kg^?1 and 2.93 W h kg^?1, respectively, at a 5 V s^?1 scan rate. For the thin-film electrode, about 53 % of the initial specific capacitance of electrodes at low scan rates was retained at a high scan rate of 20 V s^?1. Although the thickness of the thin-film electrodes has influence on their rate capability, an electrode with an increased thickness of 6 μm retained about 30 % if its initial capacitance at a very high scan rate of 20 V s^?1. The results show that the ESD-fabricated GNP electrodes are promising candidates for thin-film energy storage for applications that require moderate energy density and very high power and rate handling ability.     

Sensitive voltammetric determination of rutin at a carbon nanotubes-ionic liquid composite electrode

A new composite electrode of multiwall carbon nanotubes (MWNTs) and 1-dodecyl-3-methylimidazolium hexafluorophosphate (DDMIMPF₆) was fabricated to determine rutin. This electrode showed very attractive electrochemical performances compared to other kinds of ionic liquid modified electrodes and notably improved sensitivity and stability. Electrochemical behavior of rutin at the composite electrode had been investigated in pH 2.09 Britton–Robinson buffer solution by cyclic voltammetry and square wave voltammetry. The experimental results suggested that the composite electrode exhibited an electrocatalytic activity toward the redox of rutin. The electrochemical parameters of rutin were calculated with the results of the charge transfer coefficient (α) and the standard rate constant (k _s) as 0.48 and 2.09 s^?1. Under the selected conditions, the reduction peak current was linearly dependent on the concentration of rutin in the range of 0.03–1.5 μM, with a detection limit of 0.01 μM (S/N?=?3). The relative standard deviation for six times successive determination of 1 μM rutin was 1.6 %. The method was successfully applied to the determination of rutin in tablets and urine samples without the influence of the coexisting substances. In addition, the MWNTs/DDMIMPF₆ composite electrode exhibits a distinct advantage of simple preparation, surface renewal, good reproducibility, and stability.     

Electroless Deposition of Thionin onto Glassy Carbon Electrode Modified with Single Wall and Multiwall Carbon Nanotubes: Improvement of the Electrochemical Reversibility and Stability

A simple procedure was developed to prepare a glassy carbon electrode modified with carbon nanotubes (CNTs) and thionin. Abrasive immobilization of CNTs on a GC electrode was achieved by gently rubbing the electrode surface on a filter paper supporting carbon nanotubes, then immersing the GC/CNTs‐modified electrode into a thionin solution (electroless deposition) for a short period of time (5–50 s for MWCNTs and 5–120 s for SWCNTs ). Cyclic voltammograms of the resulting modified electrode show stable and a well defined redox couple with surface confined characteristic at wide pH range 2–12. The electrochemical reversibility and stability of modified electrode prepared with incorporation of thionin into CNTs film was compared with usual methods for attachment of thionin to electrode surfaces such as electropolymerization and adsorption on the surface of preanodized electrodes. The formal potential of redox couple (E°′) shifts linearly toward the negative direction with increasing solution pH. The surface coverage of thionin immobilized on CNTs glassy carbon electrode was approximately 1.95×10^?10 mol cm^?2 and 3.2×10^?10 mol cm^?2 for MWCNTs and SWCNTs, respectively. The transfer coefficient (α) was calculated to be 0.3 and 0.35 and heterogeneous electron transfer rate constants (K_s) were 65 s^?1 and 55 s^?1 for MWCNTs/thionin and SWCNTs/thionin‐modified GC electrodes, respectively. The results clearly show a great facilitation of the electron transfer between thionin and CNTs adsorbed on the electrode surface. Excellent electrochemical reversibility of redox couple, high stability, technically simple and possibility of preparation at short period of time are of great advantages of this procedure for modification of electrodes.     

Nanoporous gold electrode prepared from gold compact disk as the anode for the microbial fuel cell

The electrodes (anode and cathode) have an important role in the efficiency of a microbial fuel cell (MFC), as they can determine the rate of charge transfer in an electrochemical process. In this study, nanoporous gold electrode, prepared from commercially available gold-made compact disk, is utilized as the anode in a two-chamber MFC. The performance of nanoporous gold electrode in the MFC is compared with that of gold film, carbon felt and acid-heat-treated carbon felt electrodes which are usually employed as the anode in the MFCs. Electrochemical surface area of nanoporous gold electrode exhibits a 7.96-fold increase rather than gold film electrode. Scanning electron microscopy analysis also indicates the homogeneous biofilm is formed on the surface of nanoporous gold electrode, while the biofilm formed at the surface of acid-heat-treated carbon felt electrode shows rough structure. Electrochemical studies show although modifications applied on carbon felt electrodes improve its performance, nanoporous gold electrode, due to its structure and better electrochemical properties, acts more efficiently as the MFC’s anode. The maximum power density produced by nanoporous gold anode is 4.71 mW m^?2 at current density of 16.00 mA m^?2, while this value for acid-heat-treated carbon felt anode is 3.551 mW m^?2 at current density of 9.58 mA m^?2.     

Prussian Blue/Reduced Graphene Oxide Composite for the Amperometric Determination of Dopamine and Hydrogen Peroxide

Prussian blue has significant application for the construction of electrochemical biosensors. In this work, Prussian blue-reduced graphene oxide modified glass carbon electrodes were successfully fabricated using electrochemical deposition. The high surface area of graphene oxide enhanced the deposition of Prussian blue and the resulting electrocatalytic activity. Infrared spectroscopy and scanning electron microscopy showed that the relatively porous Prussian blue was on the surface of reduced graphene oxide. Cyclic voltammetry showed that Prussian blue-coated reduced graphene oxide composite films improved electron transfer compared to Prussian blue films. The Prussian blue-reduced graphene oxide composite film provided higher response for the reduction of hydrogen peroxide and the oxidation of dopamine compared with the Prussian blue film due to synergistic effects between the reduced graphene oxide and Prussian blue particles. The sensitivity of the electrode was 0.1617 µA µM^?1 cm^?2. The linear dynamic range extended from 0.5 µM to 0.7 mM dopamine with a limit of detection equal to 125 nM. This work provided a versatile strategy for the design and construction of sensitive amperometric sensors with robust electrocatalytic behavior.     

铁氰酸钴膜电极的制备及特性

首次用电化学方法在玻碳基体上制成铁氰酸钻修饰膜电极(CHCF/GC).该电极非常稳定,可经受—1.0～0.9V(vs SCE)连续万次以上的电位扫描.讨论了CHCF膜电极的电荷传递过程,研究了影响CHCF膜电极伏安特性的各种因素和对Fe~(3+)/Fe~(2+)电对的催化作用。     

Cupric Hexacyanoferrate Nanoparticle Modified Carbon Ceramic Composite Electrodes

Graphite powder-supported cupric hexacyanoferrate(CuHCF) nanoparticles were dispersed into methyltrimethoxysilane-based gels to produce a conducting carbon ceramic composite,which was used as electrode materials to fabricate surface-renewable CuHCF-modified electrodes.Electrochemical behavior of the CuHCF-modified carbon ceramic composite electrodes was characterized using cyclic and square-wave voltammetry. Cyclinc voltammograms at various scan rates indicated that peak currents were suface-confined at low scan rates.In the presence of glutathione,a clear electrocatalytic response was observed at the CuHCF-modified composite electrodes.In addition,the electrodes exhibited a distinct advantage of reproducible surface-renewal by simple mechanical polishing on emery paper,as well as ease of preparation,and good chemical and mechanical stability in a flowing stream.