4，6—二甲基二苯并噻吩加氢脱硫反应机理的研究I．NiW体系催化剂的催化行为

分别以γ－Al2O3、无定形硅铝和含少量稀土分子筛的γ－Al2O3为载体，制备了不同系列的NiW体系加氢脱硫催化剂，并在连续流动微反装置上评价了催化剂对4，6－二甲基二苯并噻吩（DMDBT）加氢脱硫反应的催化性能。结果表明，NiW体系催化剂对该反应具有较高的芳烃加氢和脱硫活性；先加氢后脱硫是加氢脱硫（HDS）反应的主要途径，提高加氢活性是提高HDS活性最有效的途径；增强载体的酸性，直接脱硫和裂解活性均有所提高。同时，酸性载体负载的催化剂还显示出一定的异构化性能，但其加氢活性低于氧化铝负载的催化剂。酸性载体负载的NiW催化剂的异构化性能在邻二甲苯异构化反应中得到进一步证实。根据实验结果，讨论了NiW体系催化剂上DMDBT转化反应的不同途径。     

H2S对NiW/Al2O3和CoMo/Al2O3上二苯并噻吩和4,6-二甲基二苯并噻吩加氢脱硫反应的影响

 考察了H2S对NiW/Al2O3和CoMo/Al2O3上二苯并噻吩(DBT)和4,6-二甲基二苯并噻吩(DMDBT)加氢脱硫反应的影响. 结果表明,H2S同时抑制DBT和DMDBT两种硫化物的加氢脱硫反应,并且对DBT的抑制作用更为明显. 对于NiW/Al2O3和CoMo/Al2O3两种催化剂,H2S抑制了DBT和DMDBT的直接脱硫路径活性; 对于CoMo/Al2O3催化剂上DBT转化中的加氢反应也有抑制作用,但促进了DMDBT转化中加氢反应的进行. NiW/Al2O3催化剂更易受H2S的影响.     

Ni含量及预硫化对NiW／γ—Al2O3催化剂上噻吩加氢脱硫反就活性的影响

采用连续流动微反装置考察了活性组分Ni／（(Ni＋W）原子比及预硫化条件对NiW/γ－Al2O3催化剂噻吩加脱硫（HDS）反应活性的影响，用X射线光电子能谱和电镜微区元素分析方法对硫化态催化剂进行了表征，结果表明，催化剂的组成、硫化方法、硫化度和反应条件等都影响NiW/γ－Al2O3催化剂的HDS反应活性，对于在较低温度（300℃）下硫化的催化剂，当反应温度较低（260－290℃）时，最佳Ni(Ni＋W）原子比为0．50，而当反应温度较高（330－360℃），最佳Ni（Ni＋W）原子比为0．23，当催化剂在300－500℃下硫化时，其噻吩HDS反应活性随硫化温度升高而增大，表明硫化度较高的催化剂具有较高的HDS反应活性。     

Ni含量及预硫化对NiW/γ-Al2O3催化剂上噻吩加氢脱硫反应活性的影响

 采用连续流动微反装置考察了活性组分Ni／（Ni＋W）原子比及\r\n预硫化条件对NiW／γ－Al2O3催化剂噻吩加氢脱硫（HDS）反应活性的\r\n影响．用X射线光电子能谱和电镜微区元素分析方法对硫化态催化剂进\r\n行了表征．结果表明，催化剂的组成、硫化方法、硫化度和反应条件等\r\n都能影响NiW／γ－Al2O3催化剂的HDS反应活性．对于在较低温度（30\r\n0℃）下硫化的催化剂，当反应温度较低（260～290℃）时，最佳Ni／\r\n（Ni＋W）原子比为0．50，而当反应温度较高（330～360℃）时，最佳\r\nNi／（Ni＋W）原子比为0．23．当催化剂在300～450℃下硫化时，其噻\r\n吩HDS反应活性随硫化温度升高而增大，表明硫化度较高的催化剂具有\r\n较高的HDS反应活性．     

噻吩加氢脱硫和四氢萘催化加氢反应中的载体和助剂的影响

 为了更好地认识加氢脱硫和催化加氢反应中的载体影响和助剂效应，在同样的催化剂制备方法及反应条件下，研究了噻吩加氢脱硫（HDS）和四氢萘催化加氢（HYD）反应．结果表明，对于无助剂的Mo和W催化剂，载体对催化活性的影响顺序为TiO2－Al2O3＞ZrO2＞Al2O3．助剂的添加改变了催化剂活性顺序．Ni助剂催化剂的活性明显高于Co助剂催化剂．ZrO2担载的添加Ni的Mo和W催化剂分别获得了最佳的HDS和HYD活性．然而，添加Pt的Mo和W催化剂其HDS和HYD活性仅是Pt与Mo（W）二者的加和，Pt与Mo（W）之间没有协同效应．先将担载的Mo和W预硫化再将助剂引入体系的催化剂制备方法可以避免Ni和Co过早硫化形成类硫化镍（或硫化钴）物相，与采用螯合物分子方法制备的催化剂间有一定的相似性．     

HY／MCM-41／γ-A12O3负载的硫化态Ni-Mo-P催化剂上萘的加氢

采用水热法合成了不同SiO2／Al2O3比的MCM-41介孔分子筛．并分别以HY／MCM-41／γ-A1203，HY／γ-A12O3和γ-Al2O3为载体，用浸渍法制备了Mo-Ni-P催化剂．以萘为模型化合物，考察了硫化态Mo-Ni-P催化剂的加氢活性．结果表明，不同载体负载的催化剂催化活性均随着活性组分负载量的增大而提高，其中掺杂大比表面MCM-41的HY／MCM-41/γ-Al2O3所负载的催化剂催化活性提高幅度最大．由于MCM-41与HY分子筛在酸性和孔结构上存在互补性，因而催化剂对萘加氢存在协同作用．提出了萘加氢的反应机理，认为反应网络包括两个平行路径：-是萘加氢生成四氢萘后发生异构化或开环反应；二是萘加氢生成四氢萘后进-步加氢生成十氢萘，继而发生异构化或开环反应．     

WP/γ-Al2O3催化剂负载方式对噻吩加氢脱硫性能的影响

以γ-Al2O3为载体，分别采用机械混合法、共浸渍法、分步浸渍法和程序升温、高纯氢气还原无定型磷钨酸盐的方法，制备了活性组分为磷化钨，负载量为20%的WP/γ-Al2O3催化剂。考察了不同方法制备的催化剂对噻吩加氢脱硫（HDS）反应的催化活性。结果表明：不同负载方式对催化剂结构有一定影响，对噻吩加氢脱硫性能的影响在低温时较明显。采用机械混合方式，先混合后还原方法制备的催化剂其HDS活性比先还原后混合方法制备的催化剂高；采用共浸渍和分步浸渍方式，通过焙烧所形成的催化剂其HDS活性分别比不经焙烧所形成的催化剂高或接近；浸渍焙烧所形成的催化剂其HDS活性远远高于机械混合法制备的催化剂。     

NiW/γ-Al2O3加氢催化剂化学吸附性质的研究

采用脉冲色谱法测定了噻吩在硫化态NiW/γ-Al2O3催化剂上化学吸附过程中热力学函数的变化,并与噻吩加氢脱硫(HDS)反应活性进行了关联.结果表明,噻吩在硫化态NiW/γ-Al2O3催化剂上的吸附不能太强,催化剂中的Ni可以降低噻吩在催化剂表面上的吸附强度,增加HDS反应活性中心的数目.从H2在硫化态NiW/γ-Al2O3催化剂上吸附后的程序升温脱附实验结果发现,H2在硫化态催化剂上有两种吸附态,高温脱附所对应的吸附态与HDS反应有关.     

Sn和Si掺杂AlPO4-5分子筛及其加氢脱硫反应性能研究

直接在AlPO4-5凝胶中加入Si和Sn2+源成功制备SAPO-5和SnSAPO-5分子筛。采用XRD、低温N2物理吸附、SEM、NMR、Py-IR、NH3-TPD等表征对分子筛物理化学性质进行分析。随Sn含量的增多,杂原子SnSAPO-5分子筛表面更光滑,外貌呈现更规则的六棱柱;Sn和Si更多的富集于表面;并且Sn2+同晶取代Al3+,骨架产生缺陷,电荷不平衡,进而产生更多的酸性位点。将分子筛用于NiW催化剂的改性,以脱除模拟油中二苯并噻吩（DBT）为探针,评价其改性加氢催化剂的加氢脱硫（HDS）反应性能。SnSAPO-5分子筛的添加在催化剂上引入了更多的酸性中心;改善载体与活性金属的相互作用;促进活性金属的硫化;形成更多的金属活性相,进而提高NiW催化剂的加氢脱硫能力。因而SnSAPO-5改性催化剂表现出比其他改性催化剂更好的HDS活性,具有良好的应用前景。     

HY/MCM-41/γ-Al2O3负载的硫化态Ni-Mo-P催化剂上萘的加氢

 采用水热法合成了不同SiO2/Al2O3比的MCM-41介孔分子筛. 并分别以HY/MCM-41/γ-Al2O3, HY/γ-Al2O3和γ-Al2O3为载体,用浸渍法制备了Mo-Ni-P催化剂. 以萘为模型化合物,考察了硫化态Mo-Ni-P催化剂的加氢活性. 结果表明,不同载体负载的催化剂催化活性均随着活性组分负载量的增大而提高,其中掺杂大比表面MCM-41的HY/MCM-41/γ-Al2O3所负载的催化剂催化活性提高幅度最大. 由于MCM-41与HY分子筛在酸性和孔结构上存在互补性,因而催化剂对萘加氢存在协同作用. 提出了萘加氢的反应机理,认为反应网络包括两个平行路径: 一是萘加氢生成四氢萘后发生异构化或开环反应; 二是萘加氢生成四氢萘后进一步加氢生成十氢萘,继而发生异构化或开环反应.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

化学计量中不确定度评定研究进展

测量不确定度是表征合理地赋予被测量之值的分散性的参数。本文针对化学计量不确定度评定基础模型仅适用于线性模型、概率分布为正态分布或缩放位移t分布等局限,介绍了近年来不确定度评定的研究热点:蒙特卡罗方法(Monte Carlo Method,MCM),不确定度评定的来源、评定概念、评估方法及其发展过程,扩大了测量不确定度评定与表示的适用范围。     

微量钙的测定方法研究进展

介绍了1995-2006年期间测定微量和痕量钙的方法,如电感耦合等离子体-原子发射光谱法、原子吸收光谱法以及离子色谱法等的工作原理和特点,并说明了其测定微量钙的应用领域。并对微量钙的测定技术进行了展望(引用文献55篇)。