用混合乳化剂制备不同粒径的乳状液

乳状液按其颗粒大小可分为普通乳状液（约IN10pm，微小乳状液（01～0·4Pm），微乳状液（001卜0．lPm）．其中微小乳状液比普通乳状液颗粒小，分散均匀，稳定性好，比微乳状液所需乳化剂的用量要低得多，在实际应用中很有前景．但有关微小乳状液的研究工作做得很少［’－‘］．在乳化过程中，若不需外界做功，靠乳化剂的自身作用，使两种不相混溶的液体自动混合，生成乳状液称为自发乳化，无需专门的乳化设备即可方便地制备出乳状液．目前自发乳化所得的乳状液颗粒都较大，稳定性较差卜一＼若将微JJ、乳状液的制备与其自发形成的条件结合…     

多重乳状液稳定性的研究

多重乳状液稳定性的研究刘沛妍，褚莹，吴子生，严忠，康万利（东北师范大学化学系，长春，１３００２４）（大庆石油学院，安达）关键词多重乳状液，示踪法，稳定性Ｗ／Ｏ型或Ｏ／Ｗ乳状液的稳定性是研究得比较成熟的课题［１］，但对Ｗ／Ｏ／Ｗ型多重（层）乳状液稳定性...     

非离子表面活性剂体系的液晶与自发乳化(I)

乳状液广泛用干工、农业、医药、食品与化妆品生产中．近年来，许多研究集中在如何制备颗粒细小、均匀的乳状液方面．用通常的机械法制备细小乳状液，需要较昂贵的设备和消耗较多能量，其颗粒分布仍不够均匀．近来，一些研究发现，有可能采用物理化学方法，而不需乳化机械，只要选用合适的乳化剂，在轻微的搅拌下，可制得颗粒细小而均匀的微小乳状液[1，2]．我们在采用反相乳化法和自发形成O／W型微小乳状液的研究中发现，在自发乳化的中间过程中常有液晶棺和粘稠的胶状物形成[3，4]．有关液晶对乳状液的稳定作用前人有过较多研究[5]，但在…     

白油乳状液稳定性实验研究与机理分析

乳状液的微观特征影响着油包水乳状液的稳定性，从而影响油基钻井液的稳定性能。室内选用3^#白油、26%CaCl₂水溶液、JH主辅乳化剂，采用超声分散乳化方法，配制得到油包水型白油乳状液。采用显微图像技术，研究了JH主辅乳化剂加量、油水比、有机土对白油乳状液微观特性的影响；以油水界面张力、动态界面张力以及界面扩张粘弹性等为参数分析了乳状液稳定性的机理。结果表明：JH主辅乳化剂配比为4∶1,加量为4%,油水比为80∶20时，白油乳状液中的分散相呈球形液珠，直径为3.31～12.93μm;油水界面张力为0.559 mN·m^-1;JH主辅乳化剂形成的油水界面膜强度大，白油乳状液稳定性好；有机土与JH主辅乳化剂的协同作用使白油乳状液和油基钻井液的稳定性能显著提高。     

原油乳状液稳定性和破乳研究进展

本文从控制乳状液稳定性的一些因素－界面膜、界面张力、双电层、空间位阻、固体粒子、液晶、油相溶解度、连续相粘度等方面综述了有关乳状液稳定性的一些研究进展。对国内外有关原油乳状液的破乳研究也做了综述。同时，介绍了应用于乳状液稳定性研究的新的实验技术和仪器。     

三元复合驱碱/表面活性剂/聚合物模拟原油乳状液稳定动力学特性

基于两相分离的乳状液稳定模型,研究了三元复合驱模拟原油乳状液稳定动力学特性;通过液膜强度和油水界面张力探讨了碱/表面活性剂/聚合物对模拟原油乳状液稳定动力学特性的影响机理。结果表明,乳状液稳定模型可以很好的评价乳状液的稳定性,并得到乳状液的稳定动力学特性;碱浓度小于900 mg/L有利于乳状液的稳定,碱浓度大于900 mg/L不利于乳状液的稳定;表面活性剂和聚合物浓度的增加使得形成的模拟原油乳状液更加稳定;模拟原油乳状液的稳定作用主要是通过碱、表面活性剂降低油水界面张力并增加油水界面膜强度,聚合物通过提高界面膜强度实现的,三者存在协同效应。     

烷基芳基磺酸钠对烷烃的乳化性能

采用分水时间法考察了结构明确的高纯度烷基芳基磺酸钠在烷烃中的乳化现象。 以液态石蜡为油相,讨论了乳化剂浓度对乳状液稳定性的影响,确定了最适宜的乳化剂浓度,并研究了烷基链长度、芳基结构和芳基在烷基链位置对形成的乳状液稳定性的影响关系,考察了不同油相对乳状液稳定性的影响。 结果表明,最适宜的乳化剂质量分数为0.1%;当固定芳基结构时,随着烷基链上碳数的增加,乳状液稳定性线性增强;当固定烷基链碳数时,随着芳基上碳原子的增加,乳状液稳定性增强;随着芳基位置向烷基链中间位置移动,乳状液稳定性增强;随着油相分子量的增加,能形成稳定乳状液所需的乳化剂的分子量随之递增。     

固体粒子稳定的乳状液研究进展

综述了固体粒子对乳状液稳定性影响的有关研究进展。微细不溶的固体粒子构成重要的一类乳化剂,被水相和油相部分润湿的固体粒子能够有效地稳定乳状液。固体粒子稳定乳状液的效果取决于以下因素:粒子大小、粒子间相互作用和粒子的润湿性质。固体粒子存在的油-水界面表现出粘弹行为,这种粘弹界面膜可大大地提高空间位阻,减缓乳状液液珠间液膜变薄的速率,从而提高乳状液地稳定性。原油中的粘土、胶质、沥青质和石蜡等胶体粒子被证明对乳状液的稳定性起很大的作用。     

以双（2,4,4—三甲基戊基）膦酸为流动载体的乳状液膜分离汞与常…

用双（２，４，４－三甲基戊基）膦酸－Ｓｐａｎ８０－甲苯乳状液膜体系研究了汞的迁移行为，确定了用此种乳状液膜迁移分离汞的适宜条件，汞在５ｍｉｎ内可迁移９６％以上。在同样条件下，一些常见过渡金属离子如Ｃｏ＾２＋，Ｎｉ＾２＋，Ｃｕ＾２＋，Ｃｄ＾２＋等通过此乳状液膜的迁移率很低，因此汞可与这些元素得到很好的分离。     

乳状液膜法提取L—谷氨酸的研究

乳状液膜法提取Ｌ－谷氨酸的研究徐占林（四平师范学院化学系四平１３６０００）严忠张河哲（东北师范大学化学系长春１３００２４）关键词Ｌ－谷氨酸乳状液膜载体萃取中图分类号Ｏ６２３．７３６氨基酸作为重要的生化产品，广泛应用于食品、饲料、医药、化工等许多领域，...     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.