在位分散聚合聚甲基丙烯酸甲酯/二氧化硅纳米复合材料研究

应用在位分散聚合方法制备了分散相粒径介于１３０ｎｍ左右的聚甲基丙烯酸甲酯／二氧化硅ＰＭＭＡ／ＳｉＯ２纳米复合材料，并利用ＳＥＭ，ＤＭＡ，ＴＧＡ等手段研究了该体系的性能．结果表明，经表面处理的ＳｉＯ２无机填料在复合材料基体中分散均匀，界面粘结好．ＳｉＯ２填充粒子的用量对基体的热稳定性，动态力学行为，光学行为以及拉伸强度，弹性模量，断裂伸长率等力学性能都有较大影响     

硅橡胶热降解动力学的研究

用恒温热失重方法，研究了甲基硅橡胶（Ｓｉ—Ｏ—１），用氢氧化钾催化聚合的甲基硅橡胶（Ｓｉ—Ｏ—２），主链含环二硅氮烷的硅氮橡胶（Ｓｉ—Ｎ—１）以及它与Ｓｉ—Ｏ—１的共混物Ｓｉ—Ｏ—３和与Ｓｉ—Ｏ—２的共混物Ｓｉ—Ｏ—４的热降解反应动力学．结果表明Ｓｉ—Ｎ—１有最高的热稳定性，在氮气下，其降解反应活化能为３４４ｋＪ／ｍｏｌ．并且发现它分别与Ｓｉ—Ｏ—１和Ｓｉ—Ｏ—２的共混物的热稳定性大幅度提高．Ｓｉ—Ｏ—３在氮气下的降解活化能由未加入Ｓｉ—Ｎ—１前的１５２ｋＪ／ｍｏｌ提高到２３０ｋＪ／ｍｏｌ；Ｓｉ─Ｏ─４则由未混入Ｓｉ─Ｎ─１前的６１ｋＪ／ｍｏｌ提高到１４４ｋＪ／ｍｏｌ．我们认为这种作用机理是由于硅氮橡胶除去了微量吸附水和硅羟基并导致催化剂的离子对难于分离的结果．     

Mo助剂对Rh／SiO_2催化剂上甲醇吸附性能的影响

用原位红外光谱和程序升温还原技术考察了甲醇在Ｒｈ－Ｍｏ／ＳｉＯ入催化剂上的吸附和还原性能．红外结果表明，甲醇在ＳｉＯ２上主要以分子形式吸附．Ｒｈ／ＳｉＯ２和Ｒｈ－Ｍｏ／ＳｉＯ２在室温下对甲醇分解就有活性，分解生成的ＣＯ以线式和桥式吸附态存在．在５７３Ｋ下用甲醇处理后，Ｒｈ／ＳｉＯ２上ＣＯ线式和桥式谱带分别位于２０５０和１９０７ｃｍ－１，而Ｒｈ－Ｍｏ（１：１）／ＳｉＯ２上线式ＣＯ位于２０３６ｃｍ－１，桥式ＣＯ强度很弱．Ｍｏ的添加有可能覆盖部分Ｒｈ金属表面的吸附中心，从而降低ＣＯ吸附谱带的强度，同时使桥式ＣＯ的形成变得困难．随Ｍｏ助剂量的增加，Ｒｈ的还原温度升高，而Ｍｏ的还原温度降低．由此推断，Ｒｈ～Ｍｏ／ＳｉＯ２催化剂上的Ｒｈ可能有三种存在形式：氯化物、低温还原氧化物和高温还原氧化物．     

Co基超细粒子催化剂用于合成重质烃Ru助剂的作用

用溶胶凝胶法制备了ＳｉＯ２气凝胶超细粉体及ＺｒＯ２ＳｉＯ２超细复合载体，用浸渍法制备了Ｃｏ／ＺｒＯ２ＳｉＯ２超细粒子催化剂并用干混法制备了ＣｏＲｕ／ＺｒＯ２ＳｉＯ２催化剂．考察了Ｒｕ的添加对Ｃｏ／ＺｒＯ２ＳｉＯ２催化剂的织构、结构、还原、氢脱附及其ＦＴ反应性能的影响．结果表明，Ｒｕ的添加使Ｃｏ２＋更难还原，催化剂活性略有下降，ＣＨ４选择性降低，Ｃ５＋选择性及收率升高；Ｃｏ１％Ｒｕ／ＺｒＯ２ＳｉＯ２催化剂上的烃类产物不遵从ＳｃｈｕｌｚＦｌｏｒｙ分布，在Ｃ９和Ｃ１５有两个最高峰．     

含氮硅烷对聚二甲基硅氧烷涂膜表面疏水性的影响

将含氮硅烷与正硅酸乙酯进行对比，研究了它们对端羟基聚二甲基硅氧烷（ＨＴＰＤＭＳ）缩合固化形成的涂膜表面疏水性的影响，发现固化剂ＮＨ２（ＣＨ２）３Ｓｉ（ＯＣ２Ｈ）３使涂膜疏水性明显下降．用ＥＳＣＡ和相差显微镜等方法证明了这种现象是由于ＮＨ２（ＣＨ２）３Ｓｉ（ＯＣ２Ｈ５）３自身固化产生的分相性引起的．     

耐高温室温硫化氟硅橡胶

采用原硅酸乙酯和硅氮聚合物（ＫＨ ＣＬ） 为交联剂制备了两种室温硫化氟硅橡胶,通过ＴＧ、ＩＧＡ 以及测定溶胶量等方法研究了两种氟硅橡胶在氮气下的降解动力学,并分别求出了降解速率和活化能．通过对比两种氟硅橡胶的热稳定性,阐述了硅氮交联剂对于提高氟硅橡胶热稳定性的作用机理．     

红外激光诱导SiO2薄膜生长的氧化动力学研究

在较低基底温度（室温至～２００℃）下，用μ０．６μｍ ＣＷ ＣＯ２激光在硅（１００）表面生成ＳｉＯ２薄膜，研究了反应气配比（Ｏ２／Ｎ２），基底温度、激光强度、激光辐照时间等实验条件对ＳｉＯ２薄膜形成的影响，探讨了红外激光助长的硅表面氧化反应动力学过程，认为在薄层氧化区域（＜３０ｎｍ）存在反应诱导期。     

负载型非晶态Cu/SiO2催化剂的非晶性质

以超细ＳｉＯ２为载体，用ＫＢＨ４还原Ｃｕ＾２＋盐溶液制备了非负载型Ｃｕ和负载型Ｃｕ／ＳｉＯ２催化剂，ＸＲＤ，ＴＥＭ和电子衍射分析结果表明，负载型Ｃｕ／ＳｉＯ２为完全非晶态，而非负载型Ｃｕ中存在着少量晶态Ｃｕ，ＤＳＣ结果表明，非晶态Ｃｕ／ＳｉＯ２的热稳定性明显高于非负载型Ｃｕ，说明超细ＳｉＯ２具有稳定非晶结构的作用，ＸＰＳ结果表明，还原产物中的铜原子呈Ｃｕ状态，ＩＣＰ分析结果表明，样品中的Ｂ含量均低     

FRS-XRSA表征双轴取向聚对苯二甲酸乙二酯薄膜的取向分布

Ｘ－射线散射理论分析（ＦＲＳ－ＸＲＳＡ）是作者为了研究和表征取向高聚物结晶度与晶粒取向分布（ＯＤＣ）的一种新方案．在表征ＯＤＣ方面应用分峰法（ＣＰＲ）消除了传统极图法（ＰＦＭ）中高重叠峰相互干扰的困难，克服了取向分布函数分析（ＯＤＦＡ）中出现虚织构的困难，并且经一次系统的ＦＲＳ－ＸＲＳ测定，可以得到几乎所有主要（ｈｋｌ）晶面法向的ＯＤＣ．作者应用ＦＲＳ－ＸＲＳＡ对二类双轴取向ＰＥＴ磁带薄膜进行了ＯＤＣ的研究。基于结晶几何学原理（ＣＧＰ），建立了三斜晶系晶粒坐标系与试样坐标系的关系，并用于推演未测定方位角（αｉ，βｉ）（ｈｋｌ）的晶面散射以及未测（ｈ′ｋ′ｌ′）晶面的ＯＤＣ．作者关系建立了双轴取向函数〈ｃｏｓ２φｈｋｌ，ｉ〉，ｉ＝Ｎ、Ｍ、Ｔ的计算公式．按照ＦＲＳ－ＸＲＳＡ获得了反映取向分布的１０个晶面的双轴极图、三个主晶面（１００）、（０１０）、（１０５）的总极图，以及反映平均取向的各种取向函数，如〈ｃｏｓ２φｈｋｌ，ｉ〉、ｆｃｈｋｌ，ｉ等，结果十分令人满意．     

微量吸附量热技术研究Pd-Cu/SiO2的表面吸附

应用微量吸附量热技术研究了室温Ｈ２,ＣＯ,Ｏ２和Ｃ２Ｈ４在ｍ（Ｐｄ）／ｍ（ＳｉＯ２）＝２％,ｍ（Ｐｄ,Ｃｕ）／ｍ（ＳｉＯ２）「ｎ（Ｐｄ）／ｎ（Ｃｕ）＝１／１」＝２％,ｍ（Ｐｄ,Ｃｕ）／ｍ（ＳｉＯ２）「ｎ（Ｐｄ）／ｎ（Ｃｕ＝１／４」＝２％和ｍ（Ｃｕ）／ｍ（ＳｉＯ２）＝８％催化剂表面的吸附性能,并考察了Ｏ２对Ｃ２Ｈ４吸附性能的影响,结果表明,Ｐｄ－Ｃｕ／ＳｉＯ２具有与Ｐｄ／ＳｉＯ２数量相近的表面Ｐｄ原子,加入Ｃｕ可使Ｐｄ对Ｈ２和ＣＯ的强吸附位数目相对减少,弱吸附位数目相对增加Ｐｄ增加了Ｈ２在Ｃｕ／ＳｉＯ２催化剂表面的吸附量,加速了Ｏ２在Ｃｕ表面的吸附速率,Ｐｄ原子和Ｃｕ原子在Ｐｄ－Ｃｕ／ＳｉＯ２混合均匀且分散良好,乙烯在Ｐｄ／ＳｉＯ２表面吸附有乙川,ｄｉ－σ和π吸附态。Ｃｕ的加入可抑制乙类在Ｐｄ表面吸附氧发生氧化反     

Synergistic effect between POSS and fumed silica on thermal stabilities and mechanical properties of room temperature vulcanized (RTV) silicone rubbers

In this paper, both divinyl-hexa[(trimethoxysilyl)ethyl]-POSS (DVPS) and fumed silica were firstly introduced into polydimethylsiloxane (PDMS) system using as the cross-linker and the reinforcing filler respectively. And a series of novel RTV silicone rubbers synergistically enhanced by DVPS and fumed silica were prepared. The cross-linked networks in the novel RTV silicone rubbers have been studied by attenuated total reflection infrared spectroscopy, and the dispersions of POSS and fumed silica in these novel RTV silicone rubbers have been observed by means of scanning electron microscope (SEM). And thermal stabilities, thermo-oxidative stabilities and mechanical properties of these novel RTV silicone rubbers were studied by means of thermal gravimetric analysis and universal tensile testing machine, respectively. From the obtained results, it was found that synergistic effect between POSS-rich areas and fumed silica on thermal stability and mechanical property of RTV silicone rubber indeed existed. And the experimental results also exhibited that the thermal stabilities and mechanical properties of the novel RTV silicone rubbers were far better than those of the reference materials (DVPR and MTFR). The striking enhancements in thermal properties and improvements on mechanical properties of novel RTV silicone rubbers were likely attributed to the synergistic effect between POSS-rich domains and fumed silica. Meanwhile, it was found that the mechanical properties of RTV silicone rubbers prepared with a given amount of POSS cross-linker were enhanced with the increment of the loading amount of fumed silica.     

Thermal behaviour and mechanical properties of novel RTV silicone rubbers using divinyl-hexa[(trimethoxysilyl)ethyl]-POSS as cross-linker

Divinyl-hexa[(trimethoxysilyl)ethyl]-POSS (DVPS) as an octavinyl-POSS derivative was first prepared. A series of novel polydimethylsiloxane (PDMS)/DVPS hybrid materials as room temperature vulcanized (RTV) silicone rubber were prepared. The chemical incorporation of novel POSS into hydroxyl-terminated PDMS system by hydrolytic condensation reaction was verified by attenuated total reflection (ATR) infrared spectroscopy. Thermal degradation, thermo-oxidative stability and mechanical properties of these novel RTV silicone rubbers were studied by means of thermogravimetric analysis and tensile testing. The results exhibited significantly enhanced effects on the thermal stabilities and mechanical properties as compared to the PDMS polymer prepared with tetraethoxysilane (TEOS). The observed improvements in thermal properties could be attributed to the effective three-dimensional network structures resulting from the structure of DVPS. The thermal decomposition of the RTV silicone rubbers in nitrogen was also monitored by TGA coupled with real-time FTIR, and the degradation residues were also characterized by FTIR. It was found that the POSS cross-linker facilitated the formation of cross-links in the degradation residues. The striking improvement in mechanical properties could be attributed to the synergistic action of the structure of three-dimensional multi-arm cross-linker (vinyl-POSS derivative), the plasticization of self-cross-linking Vinyl-POSS derivative and perfect distribution of vinyl-POSS derivative.     

Thermal characterization of Al2O3 and ZnO reinforced silicone rubber as thermal pads for heat dissipation purposes

Silicone rubber filled with thermally conductive, but electrically insulating Al₂O₃ or ZnO fillers were investigated to be used as elastomeric thermal pads, a class of thermal interface materials. The effect of Al₂O₃ or ZnO fillers on the thermal conductivity and coefficient of thermal expansion (CTE) of the silicone rubber were investigated, and it was found that with increasing Al₂O₃ or ZnO fillers, the thermal conductivity of the thermal pads increases, while the coefficient of thermal expansion (CTE) decreases. The thermal conductivity results obtained were also analyzed using the Agari model to explain the effect of Al₂O₃ or ZnO fillers on the formation of thermal conductive networks. Thermal gravimetry analysis (TGA) showed that the addition of either Al₂O₃ or ZnO fillers increases the thermal stability of the silicone rubber, while the scanning electron microscope (SEM) showed that at 10 vol.% filler loading percolation threshold has yet to be reached.     

Calcium and aluminium-based fillers as flame-retardant additives in silicone matrices. I. Blend preparation and thermal properties

This series investigates silicone composites with enhanced thermal behaviour for cable applications. Calcium and aluminium-based fillers introduced into silicone formulations were classified according to three categories: non-hydrated fillers such as CaCO₃ (precipitated calcium carbonate and natural calcite) and wollastonite, water-releasing fillers such as calcium hydroxide, ATH, boehmite, and hydroxyl-functionalized fillers including alumina and mica. The fillers were first characterized in detail, and the thermal stability of their blends with silicone was recorded by thermogravimetric analyses. A discussion on various aspects of the filler morphology (size, microstructure, release profile with temperature) on the silicone stability is finally given.     

Thermal stability of styrene butadiene rubber (SBR) composites filled with kaolinite/silica hybrid filler

Styrene butadiene rubber (SBR) composites filled with fillers, such as modified kaolinite (MK), precipitated silica (PS), and the hybrid fillers containing MK and PS, were prepared by melt blending. The kaolinite sheets were finely dispersed in the SBR matrix around 20–80 nm in thickness and reached the nano-scale. The SBR composites with fillers exhibited excellent thermal stability compared to the pure SBR. The thermal stability of SBR composites was improved with the increasing of MK mass fraction. When MK hybridized with PS, kaolinite sheets were covered by the fine silica particles and the interface between filler particles and rubber matrix became more indistinct. SBR composite filled by hybrid fillers containing 40 phr MK and 10 phr PS became more difficult in decomposition and was better than that of 50 phr PS/SBR and 50 phr MK/SBR in thermal stability. Therefore, the hybridization of the fine silica particles with the kaolinite particles can effectively improve the thermal stability of SBR composites.     

白炭黑增强型硅橡胶的组成及抗原子氧性能分析

为明确空间级硅橡胶的化学组成及填料添加对材料物理性能的影响, 采用填料复合方式制备硅橡胶高聚物材料, 并通过化学成分测试、 原子氧暴露试验及力学性能测试等研究其结构组成与物理性能. 经微观粒径测试得出硅橡胶中白炭黑填料粒径主要分布在8~16 μm; 经傅里叶变换红外光谱(FTIR)、 核磁共振波谱( ¹H NMR和 ²⁹Si NMR)和溶胶凝胶渗透色谱(GPC)测试得出硅橡胶中含有Si—Me, Si—Ph, Si—O—Si等基团和甲基、 苯基等官能团, 其分子量分散系数为1.56, 并进一步推断出硅橡胶的分子结构及基胶与交联剂的反应类型为脱羟胺型; 经原子氧暴露试验及力学试验证实, 与未改性白炭黑填充的硅橡胶高聚物材料相比, 经硅烷改性白炭黑填充的硅橡胶高聚物材料表现出更好的抗原子氧性能, 动态力学测试后储能模量高54%, 并具有更好的应力应变响应性能. 研究结果表明, 采用表面改性处理方式可增强填料与硅橡胶基质的相互作用, 从而提高填料复合型硅橡胶高聚物材料的抗原子氧性能及综合力学性能.     

Epoxy‐based composite adhesives: Effect of hybrid fillers on thermal conductivity,rheology, and lap shear strength

Thermal management is an important parameter in an electronic packaging application. In this work, three different types of fillers such as natural graphite powder (Gr) of 50‐μm particle size, boron nitride powder (h‐BN) of 1‐μm size, and silver flakes (Ag) of 10‐μm particle size were used for thermal conductivity enhancement of neat epoxy resin. The thermal properties, rheology, and lap shear strength of the neat epoxy and its composite were investigated. The analysis showed that the loading of different wt% of Gr‐based fillers can effectively increase the thermal conductivity of the epoxy resin. It has also been observed that the thermal conductivity of the hybrid filler (Gr/h‐BN/Ag) reinforced epoxy adhesive composite increased six times greater than that of neat epoxy resin composite. Further, the viscosity of hybrid filler reinforced epoxy resin was found to be increased as compared with its virgin counterpart. The adhesive composite with optimized filler content was then subsequently subjected to determine single lap shear strength. The degree of filler dispersion and alignment in the matrix were determined by scanning electron microscopy (SEM) analysis.     

多苯基三联苯有机硅化合物的合成及其对聚合物耐热性影响的研究

本文通过Diels-Alder反应合成了1,4-双(2′,3′,6′-三苯基,4′-四甲基乙烯基二硅氧基苯基)苯(简称Ⅰ)和1,4-双(2′,3′,6′-三苯基,4′-三乙氧基硅基苯基)苯(Si称Ⅱ)两种新的多苯基三联苯有机硅单体,产率均为80％左右,并作了下列耐热性研究,其结果:(1)把化合物(Ⅰ)作为硅橡胶的热稳定剂,所得硅弹性体在300℃×150小时老化后,具有较好的耐热性和机械性能;(2)化合物(Ⅱ)可以做室温胶的交联剂,所得胶片在300℃×48小时老化,仍保持好的弹性。     

Effect of carbon nanofibers on mechanical and electrical behaviors of acrylonitrile‐butadiene rubber composites

Recently, carbon nanofibers have become an innovative reinforcing filler that has drawn increased attention from researchers. In this work, the reinforcement of acrylonitrile butadiene rubber (NBR) with carbon nanofibers (CNFs) was studied to determine the potential of carbon nanofibers as reinforcing filler in rubber technology. Furthermore, the performance of NBR compounds filled with carbon nanofibers was compared with the composites containing carbon black characterized by spherical particle type. Filler dispersion in elastomer matrix plays an essential role in polymer reinforcement, so we also analyzed the influence of dispersing agents on the performance of NBR composites. We applied several types of dispersing agents: anionic, cationic, nonionic, and ionic liquids. The fillers were characterized by dibutylphtalate absorption analysis, aggregate size, and rheological properties of filler suspensions. The vulcanization kinetics of rubber compounds, crosslink density, mechanical properties, hysteresis, and conductive properties of vulcanizates were also investigated. Moreover, scanning electron microscopy images were used to determine the filler dispersion in the elastomer matrix. The incorporation of the carbon nanofibers has a superior influence on the tensile strength of NBR compared with the samples containing carbon black. It was observed that addition of studied dispersing agents affected the performance of NBR/CNF and NBR/carbon black materials. Especially, the application of nonylphenyl poly(ethylene glycol) ether and 1‐butyl‐3‐methylimidazolium tetrafluoroborate contributed to enhanced mechanical properties and electrical conductivity of NBR/CNF composites.