Silicon-hybrid carbon dots strongly enhance the chemiluminescence of luminol

We report on a 4-min microwave pyrolytic method for the preparation of fluorescent and water-soluble silicon-hybrid carbon dots (C-dots) with high fluorescent quantum yield. The material is prepared by preheating aminopropyltriethoxysilane and ethylene diamine tetraacetic acid for 1 min, then adding a mixture of poly(ethylene glycol) and glycerin to the solution and heating for another 3 min. It is found that the hybrid carbon dots strongly enhance the chemiluminescence (CL) of the luminol/N-bromosuccinimide system. A study on the enhancement mechanism via CL, fluorescence and electron paramagnetic resonance spectroscopy showed that the effect most probably is due to electrostatic interaction between the C-dots and the luminol anion which facilitates electron transfer from luminol anion to the N-bromosuccinimide oxidant. CL intensity is linearly related to the concentration of the C-dots in the range between 1.25 and 20 μg mL^?1. The detection limit is 0.6 μg mL^?1 (at an S/N of 3).

Carbon dots-based fluorescent probes for sensitive and selective detection of iodide

We report on a simple method for the determination of iodide in aqueous solution by exploiting the fluorescence enhancement that is observed if the complex formed between carbon dots and mercury ion is exposed to iodide. Fluorescent carbon dots (C-dots) were treated with Hg(II) ion which causes quenching of the emission of the C-dots. On addition of iodide, the Hg(II) ions are removed from the complex due to the strong interaction between Hg(II) and iodide. This causes the fluorescence to be restored and enables iodide to be determined in the 0.5 to 20 μM concentration range and with a detection limit of ~430 nM. The test is highly selective for iodide (over common other anions) and was used for the determination of iodide in urine.

Determination of formaldehyde based on the enhancement of the chemiluminescence produced by CdTe quantum dots and hydrogen peroxide

Water-soluble cadmium telluride quantum dots (CdTe QDs) capped with glutathione (GSH) display chemiluminescence (CL) emission on reaction with hydrogen peroxide (H₂O₂) in strongly alkaline medium. It is found that the CL is strongly enhanced on addition of formaldehyde in aqueous solution. A flow injection system was developed, and it is shown that there is good linearity between CL intensity and the concentration of formaldehyde in the 0.06–3.0 μg L^?1 range. The limit of detection is as low as 10 ng L^?1. The method was successfully applied to the determination of formaldehyde in indoor air after adsorption into an aqueous phase. The recoveries for the real samples range from 97 % to 102.5 %, and the relative standard deviation is <3.8 % for intra- and inter-assay precision.

A sensitive chemiluminescence method for the determination of cysteine based on silver nanoclusters

We have developed a sensitive chemiluminescent (CL) assay for cysteine. It is based on the use of water-soluble and fluorescent silver nanoclusters (Ag NCs) which are found to be able to strongly enhance the weak CL signal resulting from the redox reaction between Ce(IV) ion and sulfite ion. This enhancement is inhibited by cysteine under appropriate conditions. Taking advantage of this specific CL inhibition, a novel CL method for the sensitive and selective detection of cysteine was developed. This effect is interpreted in terms of an electronic energy transfer from excited state intermediate sulfur dioxide (originating from the CL reaction between Ce(IV) and sulfite ions) to the Ag-NCs. The latter become electronically excited and thus can act as a new source of emission. The method was applied to the determination of cysteine in the range from 5.0?nM to 1.0?μM, with a detection limit at 2.5?nM (S/N?=?3).

Detection of trace nitrite in waters using a QDs-based chemiluminescence analysis system

In the present work, a novel flow-injection chemiluminescence method based on CdTe quantum dots (QDs) was developed for the determination of nitrite. Weak chemiluminescence (CL) signals were observed from a CdTe QDs–H₂O₂ system under basic conditions. The addition of a trace amount of hemoglobin (Hb) caused the CL from the CdTe QDs–H₂O₂ system to increase substantially. In the presence of nitrite, the ferrous Hb reacted with the nitrate to form ferric Hb and NO. The NO then bound to ferrous Hb to generate iron nitrosyl Hb. As a result, the CL signal from the CdTe QDs–H₂O₂–Hb system was quenched. Thus, a flow-injection CL analytical system for the determination of trace nitrite was established. Under optimum conditions, there was a good linear relationship between CL intensity and the concentration of nitrite in the range 1.0?×?10^?9 to 8.0?×?10^?7 mol L^?1 (R ²?=?0.9957). The limit of detection for nitrite using this system was 3.0?×?10^?10 mol L^?1 (S/N?=?3). This method was successfully applied to detect nitrite in water samples.

Detection of Sn(II) ions via quenching of the fluorescence of carbon nanodots

We report that fluorescent carbon nanodots (C-dots) can act as an optical probe for quantifying Sn(II) ions in aqueous solution. C-dots are synthesized by carbonization and surface oxidation of preformed sago starch nanoparticles. Their fluorescence is significantly quenched by Sn(II) ions, and the effect can be used to determine Sn(II) ions. The highest fluorescence intensity is obtained at a concentration of 1.75 mM of C-dots in aqueous solution. The probe is highly selective and hardly interfered by other ions. The quenching mechanism appears to be predominantly of the static (rather than dynamic) type. Under optimum conditions, there is a linear relationship between fluorescence intensity and Sn(II) ions concentration up to 4 mM, and with a detection limit of 0.36 μM.

The determination of copper ions based on sensitized chemiluminescence of silver nanoclusters

We report on the first application of novel, water-soluble and fluorescent silver nanoclusters (Ag NCs) in a chemiluminescent (CL) detection system. A method has been developed for the determination of copper(II) ion that is based on the fact that the weak CL resulting from the redox reaction between Ce(IV) ion and sulfite ion is strongly enhanced by the Ag NCs and that the main CL signals now originate from Ag NCs. UV-visible spectra, CL spectra and fluorescent (FL) spectra were acquired to investigate the enhanced CL mechanism. It is proposed that the electronic energy of the excited state intermediate SO₂* that originates from the CL reaction is transferred to Ag NCs to form an electronically excited NC whose emission is observed. In addition, it is found that copper(II) is capable of inhibiting the CL of the nanoclusters system, but not if other common metal ions are present. The detection of copper(II) is achieved indirectly by measuring the CL intensity of Ag NCs. Under the optimized experimental conditions, a linear relationship does exist between the intensity of CL and the concentrations of copper(II) in the range of 0.2?nM to 0.1?m??. The detection limit is 0.12?nM. The method is applied to the determination of copper(II) ion in tap water with satisfactory results.

Electrochemiluminescent sensing of dopamine using CdTe quantum dots capped with thioglycolic acid and supported with carbon nanotubes

We have synthesized water-dispersible CdTe quantum dots (QDs) capped with thioglycolic acid. Their quantum yield is higher than 54%. A sensitive electrochemiluminescence (ECL) method was established based on the modification of the composite of the QDs, carbon nanotubes and chitosan on indium tin oxide glass. The sensor displays efficient and stable anodic ECL which is quenched by dopamine. A respective sensor was designed that responds to dopamine linearly in the range of 50?pM to 10?nM, and the detection limit is 24?pM. Dopamine was determined with this sensor in spiked cerebro-spinal fluid with average recoveries of 95.7%.

Quantum dot induced phototransformation of 2,4-dichlorophenol, and its subsequent chemiluminescence reaction

We have studied the CdTe quantum dot-induced phototransformation of 2,4-dichlorophenol (2,4-DCP) and its subsequent chemiluminescence (CL) reaction. Quantum dots (QDs) of different size and capped with thioglycolic acid were prepared and characterized by molecular spectroscopy, X-ray diffraction and transmission electron microscopy. In the presence of QDs, 2,4-DCP is photochemically transformed into a long-living light emitting precursor which can react with N-bromosuccinimide to produce CL with peak wavelengths at 475 and 550 nm. The formation of singlet oxygen during the phototransformation process was confirmed by the enhancement effect of deuterium oxide on the CL reaction and the change in the UV spectrum of a chemical trap. The CL intensity is linearly related to the concentration of 2,4-DCP in the range from 0.36 to 36 μmol L^?1, and the detection limit (at 3σ) is 0.13 μmol L^?1.

Solid-phase extraction of mercury(II) with magnetic core-shell nanoparticles, followed by its determination with a rhodamine-based fluorescent probe

Magnetic Fe₃O₄@SiO₂ core shell nanoparticles containing diphenylcarbazide in the shell were utilized for solid phase extraction of Hg(II) from aqueous solutions. The Hg(II) loaded nanoparticles were then separated by applying an external magnetic field. Adsorbed Hg(II) was desorbed and its concentration determined with a rhodamine-based fluorescent probe. The calibration graph for Hg(II) is linear in the 60 nM to 7.0 μM concentration range, and the detection limit is at 23 nM. The method was applied, with satisfying results, to the determination of Hg(II) in industrial waste water.

Aptamer based test stripe for ultrasensitive detection of mercury(II) using a phenylene-ethynylene reagent on nanoporous silver as a chemiluminescence reagent

We describe a paper-based chemiluminescence (CL) test for the determination of mercury(II) ion. A single-stranded DNA aptamer was first covalently immobilized via its amino groups to the hydroxy groups on the surface of cellulosic paper. The aptamer probes can capture Hg(II) ions due to their specific interaction with thymine. The CL reagent (a caboxylated phenylene-ethynylene referred to as P-acid) was immobilized on nanoporous silver (NPS@P-acid) and used a CL label on the aptamer. The stripe is then contacted with a sample containing Hg(II) ions and CL is induced by the addition of permanganate. CL intensity depends on the concentration of Hg(II) because Hg(II) increases the quantity of the P-acid-conjugated aptamer. The highly active surface of the NPS@P-acid composites results in an 8-fold higher CL intensity compared to the use of pure P-acid. This enables Hg(II) ion to be quantified in the 20 nM to 0.5 μM concentration range, with a limit of detection as low as 1 pM. This CL aptasensor is deemed to represent a promising tool for simple, rapid, and sensitive detection of Hg(II).

Albumin coated CuInS2 quantum dots as a near-infrared fluorescent probe for NADH, and their application to an assay for pyruvate

Water-soluble CuInS₂ quantum dots (QDs) stabilized with 3-mercaptopropionic acid were synthesized in aqueous solution and then coated with bovine serum albumin. The resulting particles display fluorescence with a peak at 680 nm that is effectively quenched by 1, 4-dihydro-nicotinamide adenine dinucleotide (NADH), but not by 1, 4-nicotinamide adenine dinucleotide (NAD⁺). The enzyme lactate dehydrogenase catalyzes the reduction of pyruvate and dehydrogenation of lactic acid using NAD⁺ or NADH as a cosubstrate. The new QDs were applied to monitor the course of lactate dehydrogenase-catalyzed reaction of pyruvate by detecting NADH via its quenching effect. This resulted in a convenient and selective detection scheme for pyruvate. The detection limit is as low as 25 nM.

Quantum dot-based lateral flow immunoassay for detection of chloramphenicol in milk

A novel rapid (20 min) fluorescent lateral flow test for chloramphenicol (CAP) detection in milk was developed. The chosen format is a binding-inhibition assay. Water-soluble quantum dots with an emission peak at 625 nm were applied as a label. Milk samples were diluted by 20 % with phosphate buffer to eliminate the matrix effect. The result of the assay could be seen by eye under UV light excitation or registered by a portable power-dependent photometer. The limit of CAP detection by the second approach is 0.2 ng/mL, and the limit of quantitation is 0.3 ng/mL.

In vitro monitoring of picogram levels of risperidone in human urine via luminollysozyme flow injection chemiluminescence

The anti-schizophrenic drug risperidone (RSP) exerts an inhibitory effect on the chemiluminescence (CL) of the luminol-lysozyme system. This finding forms the basis for a sensitive flow injection method for its determination at picogram levels. RSP binds to Trp62 in the lysozyme, and this leads to a conformational change upon which the CL of the system is quenched. The decrease in CL is proportional to the logarithm of the concentration of RSP, and the calibration graph is linear in the range from 0.1 pg?mL^?1 to 1.0 ng?mL^?1, with relative standard deviations of <5.0%, and a detection limit of 0.05 pg?mL^?1 (3σ). At a flow rate of 2.0 mL?min^?1, the whole process including sampling and washing is completed within 20 s. The method was successfully applied to monitoring RSP in human urine after incorporation of 2 mg of RSP, with a total excretion of 16.6% within 8.5 h.

Aminophenol-based carbon dots with dual wavelength fluorescence emission for determination of heparin

We describe the preparation of carbon quantum dots (C-dots) by a one-step hydrothermal method starting from o-aminophenol as the precursor. The C-dots exhibit bright both blue fluorescence (with excitation/emission peaks at 300/410 nm and with quantum yield of 0.40) and green fluorescence (420/500 nm; QY 0.28) without any other element doping. The unique emission properties are attributed to a synergistic effect of amino and hydroxy groups on the surface of the C-dots. The C-dots are shown to be viable fluorescent probes for heparin. The positively charged surface amino groups are assumed to interact with sulfate and carboxy groups in heparin via electrostatic interactions and hydrogen bonding. This causes the blue fluorescence of C-dots to be turned off (quenched). Fluorescence is strongest at a pH value of 6. The fluorometric calibration plot is linear in the 10 to 100 nM concentration range, with an 8.2 nM detection limit (at a signal-to-noise ratio of 3).

Open image in new window

Graphical abstract Carbon quantum dots with dual fluorescence emission bands were synthesized and are shown to be a viable fluorescent probe for heparin.

     

A lanthanide nanoparticle-based luminescent probe for folic acid

We report on a novel luminescent method for the detection of folic acid (FA), a member of the vitamin B family. Y₂O₃ nanoparticles were doped with europium(III) ions and surface-modified with captopril. Their fluorescence is quenched by FA, and intensity is a function of folic acid concentration in the 0.1 – 40 μM concentration range. The detection limit is 83 nM of FA at pH 7 and room temperature.

In-situ decorated gold nanoparticles on polyaniline with enhanced electrocatalysis toward dopamine

Gold nanoparticles were in-situ decorated on top of a polyaniline film (GNPs–PANI) via the direct electroreduction of the adsorbed AuCl ₄ ^- ions on a glassy carbon electrode that previously was coated with PANI by electropolymerization. The GNPs–PANI composite and the performance of the resultant sensors were investigated in some detail. The sensor was applied to the oxidation of dopamine (DA) with improved catalytic activity. Its catalytic current showed wide linear response toward dopamine ranging from 3 to 115 μM, with a low detection limit of 0.8 μM (S/N=3). In addition, the sensor exhibits easy-operation, fast response to dopamine, as well as excellent reproducibility and stability.

Nanosensor for dopamine and glutathione based on the quenching and recovery of the fluorescence of silica-coated quantum dots

We have constructed a fluorescent nanosensor for dopamine (DA) and glutathione (GSH) in physiologically relevant concentrations. CdTe quantum dots (QDs) were coated with silica, and dopamine-quinone (formed by oxidation of DA) is captured on the surface of silica via dual interactions (hydrogen bonding and electrostatic interaction) and quenches the photoluminescence of the modified QDs by an electron transfer process. GSH, in being a strong reducing agent, can chemically reduce the dopamine-quinone on the QDs, and this results in recovered photoluminescence. There are linear relationships between the concentrations of dopamine and GSH respectively and the intensity of the photoluminescence intensity of the QDs both in the quenched and regenerated form, the ranges being 0.0005 to 0.1 mmol?L^?1 for dopamine, and 0.1 to 10 mmol?L^?1 for GSH. The method was applied to the determination of dopamine and GSH in human serum samples with satisfactory results.

New synthesis of gold nanocorals using a diazonium compound,and their application to an electrochemiluminescent assay of hydrogen peroxide

The reaction of hydrogen tetracholoroaurate, sodium borohydride and the diazonium compound prepared from 4-aminobenzoic acid results in the formation of gold nanocorals (Au-NCs) for the first time. Scanning electron microscopy images and transmission electron microscopy images show that the Au-NCs are composed of nanowires with a diameter of 5.3 nm. A glassy carbon electrode modified with Au-NCs is found to trigger intense electrochemiluminescence of the luminol/H₂O₂ system at a potential of ?0.13 V. The effect was exploited to determine H₂O₂ in the 0.1 to 100 μM concentration range with a 30 nM detection limit.

Chemiluminescent determination of the activity of caspase-3 using a specific peptide substrate and magnetic beads

We report on a new scheme for the determination of the activity of caspase-3 using a specific peptide labeled with N-(4-aminobutyl)-N-ethylisoluminol (ABEI) as a chemiluminescent (CL) probe and on the development of magnetic separation technology. Firstly, the ABEI-labeled and biotinylated peptide was prepared and conjugated to streptavidin-coated magnetic beads (MBs) to form f-MBs (functionalized magnetic beads). The f-MBs contain a site (DEVD, Asp-Glu-Val-Asp) that is cleaved by caspase-3. Upon cleavage, the terminal residue attached to ABEI can dissociate from the f-MBs and can be used for CL detection. CL intensity is linearly related to the concentration of caspase-3 in the range 1.0 to 600 ng mL^?1, with a detection limit of 0.3 ng mL^?1. The relative standard deviation of the assay is 3.6 % at a level of 50 ng mL^?1 of caspase-3 (for n?=?11). The CL assay has been applied to the determination of caspase-3 in Jurkat cell extract with recoveries between 96.6 % and 106.1 % (n?=?5).