基于多壁碳纳米管/壳聚糖多层膜修饰玻碳电极邻苯二酚的测定

改进了碳纳米管在壳聚糖溶液中的分散方法,制备了多壁碳纳米管/壳聚糖多层膜修饰玻碳电极,对比了不同修饰层数膜电极的循环伏安和电化学阻抗行为,5层多壁碳纳米管/壳聚糖膜修饰玻碳电极的电化学性能优良.在最优实验条件下,该修饰玻碳电极对邻苯二酚(CAT)有灵敏的响应,CAT浓度在3.99×10-6～9.09×10-4mol/L范围内与氧化峰电流呈良好的线性关系,检出限为2.39×10-6mol/L(S/N=3).该修饰玻碳电极性能稳定,测定4×10-5mol/LCAT溶液,RSD(n=10)为2.1%;15周后,该电极的响应值仅降低1.9%.     

纳米复合物修饰电极的电化学传感器检测芦丁

研制了纳米复合物修饰电极,碳纳米管与表面含有大量氨基的壳聚糖在玻碳电极表面首先形成碳纳米管/壳聚糖膜,通过膜表面丰富的氨基与纳米Au的强静电吸附,在玻碳电极表面获得均匀致密的纳米金修饰层.这种基于纳米复合材料制备的新型电化学传感器对芦丁具有很好的响应,可以快速地实现电极与芦丁之间的直接电子转移,有良好的稳定性.芦丁的测定线性范围为4.00×10-7～1.77×10-5 mol/L,最低检测限为1.29×10-7 mol/L.由于抗坏血酸在该修饰电极上的氧化电位出现显著负移,因此可避免抗坏血酸对芦丁测定的干扰.该方法可以不经预分离直接检测药物中的芦丁含量.     

吲哚乙酸在纳米金/碳纳米管/壳聚糖修饰玻碳电极上的电化学行为及其检测

以壳聚糖(CS)为多壁碳纳米管(MWNTs)的分散介质,通过MWNTs/CS膜上大量氨基静电吸附纳米金粒子(nanoAu),使玻碳电极(GCE)表面形成稳定的nanoAu-MWNTs-CS-GCE修饰层,并采用电化学方法初步研究了该修饰电极的性能.探讨了吲哚乙酸(IAA)在该修饰电极上的电化学行为,结果表明,在5～200μmol/L浓度范围内以及0.78V电位条件下,以循环伏安法(CV)测得的氧化峰电流变化值与c(IAA)呈良好的线性关系,其回归方程为y=2.34×10-4+0.14x,检出限为8.33×10-6mol/L,相关系数为0.9997.     

普鲁士蓝/多壁碳纳米管修饰电极测定维生素C

利用电化学方法在多壁碳纳米管修饰的玻碳电极表面聚合一层普鲁士蓝,制备普鲁士蓝/多壁碳纳米管修饰玻碳电极,运用循环伏安法研究了维生素C(vc)在该修饰电极上的电化学行为.该修饰电极对Vc显示出快速的电化学响应和较好的电催化活性,在pH为4.0的磷酸盐溶液中,Ve浓度与其氧化峰电流在8.0×10-4～1.0×10-2 mol/L范围内呈现良好的线性关系,相关系数为0.9993,检测限为6.4×10-5mol/L.该电极具有较好的稳定性和重现性.     

芦丁在铂纳米/碳纳米管修饰电极上电化学行为研究

通过电沉积的方式在多壁碳纳米管(MWCNTs)修饰玻碳电极表面上沉积铂(pt)纳米粒子,并运用循环伏安法(CV)、示差脉冲伏安法(DPV)探讨了芦丁在铂纳米/碳纳米管/玻碳电极上的电化学行为.实验结果表明,芦丁在该修饰电极上呈现一对良好氧化还原峰,其氧化峰电流与浓度在3.2×10(-8)～1.2×10(-5)mol/L...     

碳纳米管负载铂-二氧化钌纳米颗粒用于葡萄糖传感器的研究

建立了多壁碳纳米管(MWNTs)负载铂二二氧化钌纳米颗粒的液相化学还原法.以Nafion为固定剂,将Pt-RuO2/MWNTs复合材料修饰于玻碳电极的表面,制备了一种无酶型葡萄糖传感器.实验表明:复合材料修饰的电极对葡萄糖响应电流明显,并且受抗坏血酸(AA)、多巴胺(DA)和尿酸(UA)的干扰小.本实验采用安培法测定葡萄糖,线性范围为2 0×10 3～1.0×10-2 mol/L(R～0.9965);灵敏度为119.26 μA cm-2(mmol/L)-1;检出限为1.25×10 -5 mol/L(信噪比为3);响应时间为4.8 s.PtRuO2/MWNTs修饰电极可作为性能良好的无酶型葡萄糖传感器.     

碳纳米管膜修饰玻碳陶瓷复合材料电极对亚硝酸盐的电催化还原

制备了碳纳米管膜修饰的玻碳陶瓷复合材料电极,研究了亚硝酸盐在修饰电极上的电化学行为,碳纳米管膜对亚硝酸盐的还原展现了良好的催化活性。评估了溶液pH值和施加电位对亚硝酸盐电流响应的影响,并初步探讨了催化机理。在优化的实验条件下,该修饰电极对亚硝酸盐的测定线性范围为5.0×10-5~3×10-3mol/L;检出限(3σ)为2×10-5mol/L。     

血红蛋白在壳聚糖修饰碳纳米管上的电化学特性及对过氧化氢的电催化分析

用壳聚糖对多壁碳纳米管进行修饰,构建了一种用于固定血红蛋白的新型复合材料,并研究了血红蛋白在该碳纳米管上的电化学性质及其对过氧化氢的电催化活性.扫描电镜结果表明,壳聚糖修饰的多壁碳纳米管呈单一的纳米管状,并能均匀分散在玻碳电极表面.紫外光谱分析表明血红蛋白在该复合膜内能很好地保持其原有的二级结构.将该材料固定在玻碳电极上后,血红蛋白能成功地实现其直接电化学.根据峰电位差随着扫描的变化,计算得到血红蛋白在壳聚糖修饰的碳纳米管膜上的电荷转移系数为0.57,表观电子转移速率常数为7.02 s-1.同时,该电极对过氧化氢显示出良好的催化性能,电流响应信号与H2O2浓度在1.0×10-6 ～1.5×10-3 mol/L间呈线性关系,检出限为5.0×10-7 mol/L.修饰电极显示了良好的稳定性.     

氟嗪酸在碳纳米管修饰电极上的电化学行为及含量的测定

在玻碳电极上制备了多壁碳纳米管/Nafion(MWNTs-Nafion)膜,用交流阻抗谱(EIS)、循环伏安法(CV)、线性扫描伏安法(LSV)研究了氟嗪酸在该膜上的电化学行为。与裸玻碳电极相比,这种纳米结构膜修饰的电极对氟嗪酸的电化学氧化显现出极好的促进作用,氟嗪酸的氧化峰电流明显增强,在修饰电极上于 0.97 V处产生了1个灵敏氧化峰。LSV测定氟嗪酸的线性范围为1.0×10-8～1.0×10-6mol/L和1.0×10-6～2.0×10-5mol/L,开路富集400 s后,检出限为8.0×10-9mol/L(3倍信噪比),方法可用于人尿中氟嗪酸的实时测定。     

新型纳米金修饰玻碳电极对水杨酸的电催化氧化

借助"种子媒介纳米金属生长法"制备新型的纳米金修饰玻碳电极,应用场发射扫描电镜、紫外-可见光谱分析和电化学方法等,研究该电极的表面形貌及其电化学性能.结果表明,该修饰电极对水杨酸的电化学氧化有明显的电催化作用,电极响应灵敏度是裸玻碳电极表面的1.8倍.其氧化峰电流与水杨酸浓度在5.0×10-7～8.0×10-5 mol/L范围内呈良好的线性关系,可用于水中痕量水杨酸的检测.     

Adsorption of Carbon Dioxide on Activated Carbon

The adsorption of CO2 on a raw activated carbon A and three modified activated carbon samples B, C, and D at temperatures ranging from 303 to 333 K and the thermodynamics of adsorption have been investigated using a vacuum adsorption apparatus in order to obtain more information about the effect of CO2 on removal of organic sulfur-containing compounds in industrial gases. The active ingredients impregnated in the carbon samples show significant influence on the adsorption for CO2 and its volumes adsorbed on modified carbon samples B, C, and D are all larger than that on the raw carbon sample A. On the other hand, the physical parameters such as surface area, pore volume, and micropore volume of carbon samples show no influence on the adsorbed amount of CO2. The Dubinin-Radushkevich (D-R) equation was the best model for fitting the adsorption data on carbon samples A and B, while the Preundlich equation was the best fit for the adsorption on carbon samples C and D. The isosteric heats of adsorption on carbon samples A, B, C, and D derived from the adsorption isotherms using the Clapeyron equation decreased slightly increasing surface loading. The heat of adsorption lay between 10.5 and 28.4 kJ/mol, with the carbon sample D having the highest value at all surface coverages that were studied. The observed entropy change associated with the adsorption for the carbon samples A, B, and C (above the surface coverage of 7 ml/g) was lower than the theoretical value for mobile adsorption. However, it was higher than the theoretical value for mobile adsorption but lower than the theoretical value for localized adsorption for carbon sample D.     

The Colloidal Stabilization of Carbon with Carbon: Carbon Nanobubbles as both Dispersant and Glue for Carbon Nanotubes

The superior physical properties of carbon nanotubes (CNTs) have led to their broad application. Intrinsically, CNTs tend to agglomerate from hydrophobic interactions, which is highly undesirable for solution processing and device fabrication. Commonly, a stabilizer consisting of organic surfactants or polymers is used to disperse CNTs. Recently, we synthesized nitrogen‐doped carbon hollow nanospheres (25–90 nm), termed carbon “nanobubbles”. They bear superior dispersability in water and distinctive graphitic order. Herein, we describe the nanobubble‐assisted dispersion of CNTs in aqueous solution upon sonication. This process relies on the π–π interaction between the two aromatic carbon nanostructures, which can process their carbon mixture in water into conductive filter membranes, ink, and discs. This stabilization can be extended to other aromatic carbons. In addition, the π–π interaction may create a new type of carbon p–n junction that can be used to improve charge separation.     

Growth of Single-walled Carbon Nanotubes on Substrates Using Carbon Monoxide as Carbon Source

The growth of single-walled carbon nanotubes(SWCNTs) on substrates has attracted great interests because of the potential applications in various fields. Carbon monoxide(CO) was used as the carbon source for the growth of SWCNTs on silicon substrates. Random or oriented SWCNTs can be produced by varying the CO flow rate. When the flow rate of CO was as low as 20 sccm(sccm:standard cubic centimeter per minute), dense SWCNT networks with clean surface were produced. When the flow rate was above 50 sccm, vertically aligned SWCNT(VA-SWCNT) arrays were grown. Well-aligned VA-SWCNT arrays were obtained in the temperature range of 650-800℃ and the content of large-diameter(above 1.7 nm) tubes in the array increased with the temperature. The height of the array was affected by the growth temperature, the CO flow rate, and the growth time. These findings indicate CO can be used as an efficient carbon source for the growth of SWCNTs on substrates under low flow rates.     

一维新型碳的同素异形体:碳链

碳链是一种完全一维的、具有电子轨道sp杂化结构的新型碳的同素异形体。正是由于碳链的独特的一维结构,使其拥有区别于富勒烯、石墨烯和碳纳米管的化学键,从而表现出更加优异的性能,如:理论预言碳链的机械强度是石墨烯的几倍;碳链的导热也类似于石墨烯和碳纳米管;碳链是具有直接带隙的半导体材料,且带隙的大小可以通过其长度来调控,其长度越长,带隙越小。尽管关于碳链的研究早在19世纪已经启其端绪,但是一直进展缓慢。直到近期,关于碳链的研究才有了几次突破性的进展,引起了学术界的广泛讨论。本文介绍了碳链的概念、结构和特殊的物理性质,在此基础上进一步介绍了碳链的几种典型的合成方法以及应用前景,重点阐述了近期碳链研究上的几次重大突破,并对于碳链研究的未来进行了展望,希望能引起国内外同行的关注。     

埃洛石纳米管模板法一步法制备一维碳纳米管/碳纳米棒混合纳米碳材料

利用埃洛石纳米管(HNTs)特有的中空纳米结构,以及丰富的界面化学性质,以聚乙烯醇(PVA)为碳源,采用浸渍填充纳米孔方法实现了一步制备一维碳纳米管(CNTs)/碳纳米棒(CNRs)混合纳米碳材料。考察模板剂(HNTs)和碳源(PVA)之间的比例关系对混合纳米碳材料的结构影响,利用XRD、FTIR、Raman、N2吸附-脱附测试、TEM、SEM以及电阻率和分散性等表征手段分析混合纳米碳材料的结构变化。结果发现,PVA填充含量的增加将导致产物中CNRs的质量分数增加;当PVA和HNTs质量之比为1∶1时,所制备的CNTs/CNRs的孔体积达到最大值2.142 cm~3·g-1,比表面积达到583 m~2·g-1,并且表现出较好的电导率和分散性,表明低的PVA填充比例制备的混合碳材料中CNTs含量较高。     

碳纳米管含量对炭炭复合材料组织及力学性能的影响

炭纤维上原位合成了均匀生长且具有伸张形貌的碳纳米管,借助化学气相渗透制备了碳纳米管增强的炭炭复合材料,研究了不同含量的碳纳米管对炭炭复合材料组织和力学性能的影响。结果表明：炭纤维上生长碳纳米管改变了热解炭的沉积行为,诱导了各向同性热解炭的生成,且随着碳纳米管含量的增加,各向同性热解炭的厚度增加,但是复合材料的d002值却明显降低。微量的碳纳米管即可显著提高复合材料的力学强度,随着其含量的增加,复合材料的力学强度和模量迅速提高,但材料的断裂行为却急剧恶化,断裂模式由最初的假塑性断裂转变为脆性断裂。     

二氧化碳与低碳经济发展

由于二氧化碳无色无味,又存在于大气中,因此它在植物生长中的重要性被人类忽略了。其实二氧化碳是光合作用的反应物,是植物生长的重要原料;又是一种新型绿色肥料。人类应该着力开发以二氧化碳为原料的新型肥料发展低碳经济。     

Carbon clusters

Some of the most significant discoveries and achievements concerning the mass spectra and gas phase ion chemistry of carbon clusters are reviewed. These include (1) nanosecond and femtosecond laser ionizations; (2) ion structures through ion/molecule reactions, ion chromatography, and computational methods; (3) carbon cluster cooling through radiative decay, dissociative decay, and thermionic emission; (4) mechanisms and energetics of fragmentation reactions; (5) endohedral fullerenes including recent data on ion beam implantation, and (6) ion chemistry as a function of the fullerene charge state.     

Ni/γ-Al2O3催化剂上CH4-CO2重整体系中积碳-消碳的研究

用动态热重技术和色谱技术联用以及XRD和TEM等表征手段,研究了Ni/γ-Al     

Palladium-Catalyzed Addition of Carbon Monoxide and Carbon Tetrachloride to 1-Octene in Supercritical Carbon Dioxide

The Pd-catalyzed addition of carbon monoxide and carbon tetrachloride to 1-octene gave coadduct [alkyl 2-( 2, 2, 2-trichloroethyl)octanoate] as the major product in supercritical carbon dioxide by using pyridine as the base. It was found that the selectivity and the yield of coadduct were greatly affected by the pressure of carbon dioxide, the reaction temperature and the amounts of alcohol and base used.