LaCoO3模型催化剂SO2中毒机理的研究

运用ＳＥＳ、ＸＰＳ,ＸＲＤ和ＴＥＭ等手段研究了ＬａＣｏＯ３模型催化剂ＳＯ２中毒过程表面化学状态,晶相结构及表面形貌的变化状况、初步推断了ＬａＣｏＯ３钙钛矿型复合金属氧化物催化剂的ＳＯ２中毒机理,在ＳＯ２强化中毒过程中,ＳＯ２与催化剂的活性组分ＬａＣｏＯ３反应硫酸镧和氧化亚钴,而在催化剂膜层内部则生成硫酸镧,亚硫酸镧及氧化亚钴。ＳＯ２对活性组分层的侵入及硫与ＬａＣｏＯ３活性组分的反应破 催化剂的钙钛矿结构,使得催化剂彻底中毒,当中毒温度较低及中毒时间较短时,硫在膜层中呈峰形分布,其浓度随中毒温度及时间的增加而增加,随中毒温度的升高及中毒时间的增长,由于亚硫酸盐的分解作用,Ｓ在活性层中的浓度反而降低,中毒深度则继续增加。     

钙钛矿型LaCoO3的光催化活性

对钙钛矿型ＡＢＯ３复合氧化物的物理化学性质已有许多研究,但对其光催化活性很少报道．我们曾报道ＳｒＴｉＯ３［１］、ＰｂＴｉＯ３［２］等的制备及其对水溶性染料的光催化降解．本文报道ＬａＣｏＯ３的制备及其光催化活性．ＬａＣｏＯ３用柠檬酸络合法制取,所用试剂...     

炭担载的Mo和CoMo加氢脱硫催化剂

用仲钼酸铵和酸钴水溶液浸渍方法将ＭｏＯ３和ＣｏＯ担载在少在性炭担体上，制成Ｍｏ／Ｃ和ＣｏＭｏ／Ｃ催化剂。运用ＤＴＡ，ＸＰＳ，ＦＴ－ＬＲＳ等手段考察了ＭｎＯ３在活性炭担体表面的分散状态及Ｈ２还原能力随ＭｏＯ３含量的变化，并在中压固定床反应装置上测定了催化剂的噻吩加氢脱硫和环己烯加氢反应活性。     

Co/ZrO2催化剂的结构及TPR性能研究

采用ＸＲＤ和ＴＰＲ技术研究了Ｃｏ－Ｚｒ－Ｏ体系催化剂的物相结构及还原性能,并以ＣＯ氧化反应为探针考察了催化剂的氧化活性,结果表明,钴的存在会阻止ｔ－ＺｒＯ２→混合相→ｍ－ＺｒＯ２的转变和ＺｒＯ２颗粒的增长,高温焙烧后,部分钴氧化物与载体ＺｒＯ２形成固溶体,Ｃｏ／ＺｒＯ２催化剂中的钴以Ｃｏ３Ｏ４的形式存在,钴锆之间的相互作用有利于钴的分散,随着Ｃｏ负载量增加,催化剂的ＣＯ氧化活性提高。     

Ln(Ⅲ)-Co(Ⅱ)与双水杨醛缩乙二胺Schiff碱异核配合物的合成与波谱性质

合成了双水杨醛缩乙二胺Ｓｃｈｉｆ碱（ＳＡＬＥＮ）与钴的配合物Ｃｏ（ＳＡＬＥＮ）（ＮＯ３）２·３Ｈ２Ｏ及镧系－钴的异核配合物ＬｎＣｏ（ＳＡＬＥＮ）２（ＮＯ３）５·２Ｈ２Ｏ（Ｌｎ＝Ｌａ，Ｎｄ，Ｓｍ，Ｇｄ，Ｙｂ，Ｙ）．以紫外、红外光谱，特别是１ＨＮＭＲ及ＥＰＲ波谱等方法研究了它们在组成、结构和配位等方面的异同．文中讨论了配合物ＥＰＲ谱在不同溶剂中峰宽的相对关系、配合物晶体场强度及Ｇｄ３＋周围局部对称性等问题．     

稀土氧化物上SO2和NO的催化还原 Ⅱ.用CO作还原剂的脱硫及反应机理

采用连续流动固定床石英反应器,在反应气体为１％ＳＯ２和２％ＣＯ,流量为１８０ｍｌ／ｍｉｎ,以及催化剂用量为０．５ｇ的条件下,考察了经活化处理的稀土系列氧化物对ＣＯ还原ＳＯ２的催化活性,探讨了空速、温度和水蒸气等因素对反应的影响,所研究的样品依据对ＳＯ２的转化能力可分为三组：高活性的镧、镨、钕、钐、铕和钆氧化物;低活性的铈、狄和铒氧化物;无活性的铽和氧化物,在活性最高的钕和钐氧化物样品上,４５０℃时ＳＯ２的转化率〉９８％,反应过程中,活性相为稀土氧硫化物,反应遵从ＣＯＳ中间物机理。     

含氧化镧的甲烷氧化偶联催化剂的一些特性

利用ＤＴＡ、ＴＰＤ－ＭＳ、ＸＲＤ、ＴＰＲ及ＴＰＳＲ－ＭＳ等手段对Ｌａ＿２Ｏ＿３和含Ｌａ＿２Ｏ＿３的甲烷氧化偶联催化剂进行了研究。实验发现含Ｌａ＿２Ｏ＿３的催化剂的一个特点是其容易吸水，此时，催化剂中除含Ｌａ＿２Ｏ＿３外，还有Ｌａ（ＯＨ）＿３及Ｌａ＿２Ｏ＿３ＣＯ＿２存在。ＴＰＲ及ＴＰＳＲ结果表明了催化剂的起始氢气还原温度与纯甲烷的程序升温反应开始温度的一致性，这说明催化剂的晶格氧参与了甲烷的活化过程。不同的氧化物由于其晶格氧的活性不同，因而其活化甲烷的温度不同。Ｌａ＿２Ｏ＿３中的晶格氧非常活泼，它在７３０℃时即可以与甲烷或与Ｈ＿２反应而本身被还原。甲烷和氧气共进料时的程序升温反应（ＴＰＳＲ－ＭＳ）表明甲烷氧化偶联反应中Ｃ＿２烃的选择性有一最佳温度范围。     

Ln（Ⅲ）—Co（Ⅱ）与以水杨醛缩乙二胺Schiff碱异核配合物的合成与波谱性质

合成了双水杨醛缩乙二胺Ｓｃｈｉｆｆ碱（ＳＡＬＥＮ）与钴的配合物Ｃｏ（ＳＡＬＥＮ）（ＮＯ３）２．３Ｈ２Ｏ及镧系－钴的异核配合物ＬｎＣｏ（ＳＡＬＥＮ）２（ＮＯ３）５．２Ｈ２Ｏ（Ｌｎ＝Ｌａ，Ｎｄ，Ｓｍ，Ｇｄ，Ｙｂ，Ｙ）以紫外红外光谱，特别是ＨＮＭＲ是ＥＰＲ波谱等方法研究了它们在组成、结构和配位等方面的异同，中讨论了配合物ＥＰＲ谱在不同溶剂中峰宽的相对关系，配合物在晶体场强度及Ｇｄ＾３＋周围局部对称性等     

钙钛矿型LaCoO3—δ和La1—xSrxCoO3—δ纳米粒子的XPS表征

采用ＸＰＳ等手段对ＬａＣｏＯ３－δ和Ｌａ１－ｘＳｒｘＣｏＯ３－δ纳米粒子进行了表征。结果显示,随ＬａＣｏＯ３－δ纳米粒子粒径的减小,一方面表面钴浓度增加,另一方面,表面ＣｏＯ键的离子性增强和表面氧空位浓度增加。此二者共同导致ＬａＣｏＯ３－δ对一氧化碳氧化的催化活性随其粒径减小而明显增大。ＬａＣｏＯ３－δ纳米粒子中镧被锶部分取代后,其表面结构发生了变化,并导致对一氧化碳氧化的催化活性显著提高     

钙钛矿型复合氧化物LaFeO3和LaCoO3的光催化活性

采用柠檬酸法合成了钙钛矿复合氧化物ＬａＦｅＯ３和ＬａＣｏＯ３,并以其为光催化剂对水溶性染料进行光催化降解实验,研究了不同光源和不同光照时间对降解脱色率的影响。结果表明ＬａＦｅＯ３和ＬａＣｏＯ３均有较强的光催化活性,而ＬａＣｏＯ３的光催化活性明显高于ＬａＦｅＯ３,这主要与Ｆｅ＾３＋和Ｃｏ＾３＋离子的电子构型以及Ｆｅ－Ｏ间和Ｃｏ－Ｏ间的结合能有关。     

氧存在下钙钛矿LaCoO3硫化过程的XPS研究

 采用XPS,XRD和TEM对含氧气氛下钙钛矿LaCoO3硫化活化过程中不同阶段的催化剂进行了表征分析．在硫化初期,经SO2预中毒后,吸附氧种不存在,Co2p3／2结合能发生明显的位移,La3d的XPS双峰变得不明显,同时出现不稳态的S4＋物种,表明催化剂LaCoO3被SO2的强吸附所覆盖;催化剂LaCoO3仍为钙钛结构并没有新的物相产生,SO2中毒仅在催化剂表面进行．在进一步的硫化活化过程中,出现吸附氧物种,Co出现三种价态,分别对应于LaCoO3,Co3O4和CoSO4,La3d的XPS双峰变得特别明显,同时催化剂表面出现S2－物种和S6＋物种．可以认为,在含氧气氛下硫化LaCoO3的过程中,SO2预中毒为进一步硫化提供硫物种,吸附氧物种保证硫化过程中钙钛矿结构不会被完全破坏．     

LaCoO3 acting as an efficient and robust catalyst for photocatalytic water oxidation with persulfate

Cobalt-containing metal oxides [perovskites (LaCoO(3), NdCoO(3), YCoO(3), La(0.7)Sr(0.3)CoO(3)), spinel (Co(3)O(4)) and wolframite (CoWO(4))] have been examined as catalysts for photocatalytic water oxidation with Na(2)S(2)O(8) and [Ru(bpy)(3)](2+) as an electron acceptor and a photosensitizer, respectively. Catalysts with the perovskite structure exhibited higher catalytic activity as compared with the catalysts with the spinel and wolframite structures. LaCoO(3), which stabilizes Co(III) species in the perovskite structure, exhibited the highest catalytic activity in the photocatalytic water oxidation compared with CoWO(4), Co(3)O(4) and La(0.7)Sr(0.3)CoO(3) which contain Co(II) or Co(IV) species in the matrices. The high catalytic reactivity of LaCoO(3) possessing perovskite structure was maintained in NdCoO(3) and YCoO(3) which exclusively contain Co(III) species. Thus, the catalytic activity of Co ions can be controlled by the additional metal ions, which leads to development of highly reactive and robust catalysts for the photocatalytic water oxidation.     

Cation self-diffusion in LaCoO(3) and La(2)CoO(4) studied by diffusion couple experiments

Reaction kinetics between dense, polycrystalline pellets of La2O3 and CoO were investigated at temperatures of 1370-1673 K and oxygen partial pressures of 40 Pa - 50 kPa. At high oxygen partial pressures, single phase LaCoO3 was formed. The growth of the LaCoO3 phase followed the parabolic rate law. The location of Pt markers demonstrated that diffusion of Co3+ cations in LaCoO3 dominated over diffusion of La3+. The diffusion coefficient of Co3+ was determined from the parabolic rate constant, and an activation energy of (250 +/- 10) kJ mol-1 was found. The diffusion coefficient of Co3+ in LaCoO3 decreased with decreasing oxygen partial pressure. At the lowest oxygen partial pressure investigated, two product phases, LaCoO3 and La2CoO4, were observed. The diffusion coefficient of Co cations in La2CoO4 was estimated. Results were discussed in relation to cation diffusion in other LnBO3 oxides (B = Cr3+, Mn3+, Fe3+). A correlation between diffusion of the B cation and the melting point was found for LnBO3 materials.     

ABO3型钙钛矿结构的可见光光催化剂LaCo0.5Ti0.5O3的设计与合成

采用溶胶-凝胶法在较低温度条件下设计合成了新型的具有ABO3型钙钛矿结构的三元金属复合氧化物LaCo0.5Ti0.5O3. 通过TG-DTA, XRD, XPS, UV-Vis DRS等测试技术和可见光光催化活性测试对其进行了表征. 结果表明, 与LaCoO3和La2Ti2O7相比, LaCo0.5Ti0.5O3样品表现出相对较高的可见光光催化活性, 并且合成温度较低. 这是由于原料中的Co2+和Ti4+离子通过电荷补偿作用使产物B位的两种金属均以+3价氧化态分布所致.     

Ce掺杂对La1-xCexCoO3催化剂的结构和催化氧化性能的影响

采用非晶态配合物的方法合成了La1-xCexCoO3(x=0、0.05、0.1、0.2、0.3)催化剂, 并采用X射线衍射(XRD)、透射电镜(TEM)和比表面测定仪(BET)等手段对催化剂的微观结构进行了研究. 揭示了Ce掺杂对催化剂的钙钛矿结构, CO催化氧化以及催化氧化发光性能的影响规律. 结果表明, 在Ce4+掺杂部分取代La3+后, 催化剂形成了镧不足的La1-xCeyφx-yCoO3(φ是A位离子空位)钙钛矿相以及CeO2和Co3O4物相. 与LaCoO3催化剂相比, x=0.1催化剂的CO催化氧化活性最高(T100%=290 ℃). La1-xCexCoO3催化剂对CO催化氧化发光的响应与其催化活性密切相关.     

Cu-Co bi-metal catalyst prepared by perovskite CuO/LaCoO3 used for higher alcohol synthesis from syngas

Cu-Co bi-metal catalysts derived from CuO/LaCoO3 perovskite structure were prepared by one-step citrate complexing method, and the structure evolution reaction from CuO/LaCoO3 to Cu-Co2C/La202CO3 under 1-12 pretreatment was investigated by techniques of XRD, TPR and TEM. The results suggest that a much higher dispersion of copper significantly enhanced the reduction of cobalt, and a stronger interaction between copper and cobalt ions in LaCoO3 particles led to the formation of bi-metallic Cu-Co particles in the reduced catalysts and the enrichment of Co on the surface of bimetallic particles. The prepared catalysts were highly active and selective for the alcohol synthesis from syngas due to the presence of copper-modified C02C species.     

Cation deficient layered Ruddlesden-Popper-related oxysulfides La2LnMS2O5 (Ln=La, Y; M=Nb, Ta)

The structures of the new oxysulfide Ruddlesden-Popper phases La2LnMS2O5 (Ln=La, Y; M=Nb, Ta) are reported together with an iodide-containing variant: La3-xNb1+xS2O5I2x (0相似文献   

无气相氧条件下La0.8Sr0.2Fe0.9Co0.1O3钙钛矿氧化物的氧物种直接氧化甲烷

以La0.8Sr0.2Fe0.9CO0.1O3钙钛矿氧化物作氧载体,采用连续流动反应和连续顺序Redox反应考察了氧物种氧化甲烷的反应性能.结果表明,连续流动反应中La0.8Sr0.2Fe0.9CO0.1O3氧化物的氧物种能选择氧化甲烷生成合成气.在适宜的再氧化条件下,通过连续顺序Redox反应实现了La0.8Sr0.2Fe0.9CO0.1O3氧化物的氧物种氧化甲烷连续生成合成气,消耗的氧物种可通过与气相氧反应而得到补充.但随着Redox反应的进行,氧化物的持续供氧性能下降,钙钛矿结构被破坏.     

The effect of Cu substitution on microstructure and thermoelectric properties of LaCoO(3) ceramics

La(Co, Cu)O(3-δ) ceramics were prepared by pressureless sintering of citrate precursor powders, and their thermoelectric properties were investigated with an emphasis on the influence of Cu doping and phase structure as well as microstructure. It was found that a secondary phase first appeared in the form of a network along the grain boundaries and then changed to dispersion with increasing Cu content, which effectively reduced the lattice thermal conductivity of the materials. The thermal conductivity was only 1.21 W m(-1) K(-1) for the sample LaCo(0.75)Cu(0.25)O(3-δ), being much lower as for the thermoelectric oxide materials. In addition, a small amount of Cu substitution for Co increased the electrical conductivity greatly and the absolute Seebeck coefficient, whose sign was also reversed from negative to positive. The dimensionless figure of merit, ZT, of LaCoO(3-δ) oxides at low and middle temperatures can be remarkably enhanced by substituting Co with Cu.