Hydrodehalogenation of 4-chlorophenol and 4-bromophenol over Pd–Fe/Al2O3: influence of catalyst reduction conditions

The reduction of monometallic Pd/Al₂O₃ and bimetallic PdFe/Al₂O₃ catalysts produced by co-impregnation or sequential impregnation of the support with metal salts was possible not only under high temperature hydrogen treatment but also at 30 °C under the action of aqueous phenol solution and hydrogen. According to the XPS data, both reduction routes provided sufficient degrees of Pd reduction required for fast hydrodehalogenation of 4-chlorophenol and 4-bromophenol to phenol in aqueous solutions. The degree of Pd reduction was higher in the co-impregnated bimetallic PdFe catalyst, which was more efficient in transformation of 4-bromophenol; the bimetallic catalysts were more stable than the monometallic Pd one in the conversion of 4-chlorophenol.     

Progress on the development of uniform distributed Pd electroless based catalysts on MEA for PEMFC application

Envisaging the scale-up production of fuel cell electrodes, it was established an electrode manufacturing method that enables a uniform distribution of Pd-based catalyst over the MEA, ensuring simultaneously a low catalyst loading. The new procedure relies on the direct immobilization of the catalyst on the gas diffusion substrate by the electroless deposition after substrate activation by the electrodeposition of metal nucleus of Pd using the galvanostatic mode. The effect of the novel method on the catalyst distribution uniformity, morphology, and electrocatalytic activity towards the oxygen reduction reaction (ORR) in 0.1 M HClO₄ solution is compared to samples prepared by the conventional Sn/Pd sensitization—activation route. The performance of the PEMFC containing the same Pd load (0.09 mg cm^?2) reveals to be slightly higher on depositing the Pd nucleus by the galvanostatic electrodeposition than by the conventional sensitization/activation method. The new method opens up new approaches to extend the electroless deposition to the preparation of a wide range of alloy catalysts for the cathode and anode sides of PEMFCs.     

质子交换膜燃料电池Pd修饰Pt/C催化剂的电催化性能

通过对Pt催化剂表面进行Pd修饰提高质子交换膜燃料电池阴极催化剂的氧还原反应(ORR)活性. 采用乙二醇还原法制备了不同比例的Pd修饰Pt/C催化剂. 透射电镜(TEM)和X射线衍射(XRD)测试结果表明, 制备的催化剂贵金属颗粒粒径主要分布在1.75～2.50 nm之间, 并均匀地分散在碳载体表面. 循环伏安方法(CV)研究表明Pd修饰Pt/C催化剂的电化学活性面积低于传统的Pt/C催化剂. 但通过旋转圆盘电极(RDE)测试研究发现, 制备的催化剂具有比传统Pt/C催化剂高的ORR活性.     

甲醛电化学传感器多孔气体扩散电极不同催化层结构与响应性能研究

多孔气体扩散电极的制备是制备甲醛电化学传感器的关键所在, 其中催化层的结构直接影响到传感器的响应性能. 通过柠檬酸三钠还原法合成了纳米金-活性炭、纳米金-碳纳米管催化剂, 制备了甲醛电化学传感器多孔气体扩散电极, 并对电极进行SEM(扫描电子显微镜)物理表征. 在甲醛气体浓度为0.24和0.63 mg/m³时, 电极C具有较好的响应, 在0.1到0.84 mg/m³浓度范围内, 线性方程为y＝10.515x＋4.4049 (R²＝0.9917), 响应时间约80 s. 分析了不同催化剂的气体扩散电极结构与甲醛响应性的关系, 为研制开发性能优良的甲醛电化学传感器奠定了基础.     

Catalytic hydrodechlorination reaction of chlorophenols by Pd nanoparticles supported on graphene

Chlorophenols are widely used as industrial chemicals such as herbicides, insecticides, wood preservatives, and disinfectants. However, chlorophenols are very toxic materials and they have become the cause of current environmental issues. Hydrodechlorination (HDC) reaction is a more environmentally friendly removal method of chlorophenols than other methods. In this paper, Pd–modified graphene was prepared and applied to HDC reaction. Pd supported on graphene (refer to Pd/G) was prepared using the recently reported microwave irradiation method. The Pd(II)/GO was made by impregnation methods of palladium precursors in solution phase and was subsequently reduced to Pd/G by microwave irradiation. The morphological and chemical structure of the Pd/G was characterized by XRD, SEM, ICP-MS, EDS, and TEM. It was found that the graphene-based Pd catalyst showed the highest catalytic performance among Pd/Y, Pd/MCM-41, and Pd/G catalysts. This is attributed to the smaller particle size and higher dispersions of Pd nanoparticles on the graphene surface. The catalytic HDC of chlorophenols was investigated. For HDC reaction, 100 ppm solution of chlorophenols such as 4-chlorophenol, six isomers of dichlorophenol, and 2,3,5-trichlorophenol in isopropanol was treated with catalyst and base, such as Na₂CO₃ and K₂CO₃, under a hydrogen gas at ambient pressure. The progress of the chlorophenol decomposition was analyzed with GC. All chlorophenols were completely decomposed within 2 h in the 3 % Pd/G catalyst. The reaction pathway of chlorophenols was elucidated from the conversion of chlorophenols and selectivities of products. The reuse of the catalyst was also studied. The performance of the recycled catalyst in HDC reaction up to six successive runs was observed.     

Effects of different Pt-M (M = Fe,Co, Ni) alloy as cathodic catalyst on the performance of two-chambered microbial fuel cells

For the purpose of reducing the cost and improving the performance of cathodes in microbial fuel cells (MFCs), we prepared Pt/C and Pt-M/C (M = Ni, Co, Fe) electrodes, and characterized them by SEM, XRD and CV. The modified electrodes were used as the cathodes in double-chambered MFCs fed with synthetic medium and molasses sewage respectively. We have found that Pt-M/C catalysts had a better catalytic activity for oxygen reduction than Pt/C in the following order: Pt-Fe/C > Pt-Co/C > Pt-Ni/C > Pt/C. The maximum power density of the MFCs with Pt-M/C cathode was improved by 18–31% compared with the MFC with Pt/C cathode because of the decrease of activation loss in the cathode. This study shows that Pt-M/C catalysts can improve power generation of MFCs without affecting the COD removal and it is proposed that Pt-Fe functions best among the three Pt-M alloys as an efficient and cost-effective catalyst of MFCs.     

用NH4F络合还原法制备的炭载Pd催化剂对甲酸分解的催化性能和甲酸氧化的电催化性能

直接甲酸燃料电池(DFAFC)的两大问题是炭载Pd(Pd/C)催化剂对甲酸氧化的电催化稳定性不好和Pd催化剂能催化甲酸分解。发现用NH4F络合还原法制备的NH4F修饰Pd/C催化剂对甲酸氧化的电催化活性要比Pd/C催化剂好大约20%,电催化稳定性也要稍优于Pd/C催化剂。在120 s内和30℃下,甲酸在Pd/C催化剂上分解产生38 mL气体,但在NH4F修饰Pd/C催化剂上基本上不分解,因此NH4F修饰主要能抑制Pd催化剂催化分解甲酸的能力,而且又能在一定程度上提高Pd/C催化剂对甲酸氧化的电催化性能。     

磷钼酸修饰炭载Pd电极的H2O2电催化还原

采用化学还原法制备了炭载钯（Pd/C）催化剂,浸渍修饰磷钼酸（PMA）制备成复合催化剂. 通过XRD和红外谱图（IR）表征催化剂的组分和结构,采用线性扫描曲线及计时电流曲线考察了该电极的电催化性能. 研究表明,室温（20 ^oC）PMA-Pd/C电极的H₂O₂还原电催化活性更优.     

Pd/BiOCl高效室温催化甲醛产氢性能研究

利用浸渍-还原法制备Bi OCl纳米片负载的钯纳米颗粒催化剂(Pd/Bi OCl),对室温催化氧化HCHO产氢性能进行了研究,并与纯Pd纳米颗粒催化效果进行了对比.研究结果表明,Pd/Bi OCl催化剂在有效降低贵金属Pd用量情况下(仅为2%wt),仍表现出比纯Pd纳米颗粒更高的催化HCHO产氢的性能.此外,通过进一步优化甲醛浓度、氢氧化钠浓度、氧气浓度和反应温度等参数,Pd/Bi OCl催化氧化HCHO产氢速率最高可达到200 m L/(min*gcatalyst).进一步研究结果表明,Pd/Bi OCl催化HCHO产氢反应的活化能仅为15.2 k J/mol,远低于无催化剂条件下甲醛产氢的活化能65 k J/mol.     

Cathode of a fuel cell with a solid polymer electrolyte: Calculating overall currents in the presence of a gas-diffusion layer

Mathematical apparatus, which makes it possible to perform calculations of the current-voltage characteristics of cathodes of fuel cells with a solid polymer electrolyte in conditions where there are present extraneous diffusion restrictions is proposed. In so doing, the partial pressure of oxygen and the absolute pressure of gas in the gas chamber may assume any values. First of all presented are the results of calculations of the current-voltage characteristics intrinsic to active layers of the air and oxygen cathodes, which are performed under the assumption that the extraneous diffusion restrictions are absent altogether. Thereafter, in the same conditions (at the same parameters that characterize the active layer of a cathode), obtained are results of a calculation of the current-voltage characteristics inherent in the air and oxygen cathodes in the presence of extraneous diffusion restrictions. Afterward there is performed an analysis of the way a gas-diffusion layer restricts the process of generation of current in a cathode and of what measures should be taken in order for the extraneous diffusion restrictions to become less significant.     

Ni基催化剂上木质素模型化合物苯基苯乙醚C-O键的加氢裂解

研究了Ni基催化剂上木质素模型化合物苯基苯乙醚中C-O-C键加氢裂解性能.结果表明,Ni/C催化剂显示出优异的加氢裂解能力,苯基苯乙醚的转化率达到99%以上.Ni/C催化剂的还原方法对裂解选择性有重要影响;氢气还原制备的Ni/C-H催化剂上,C-O-C键裂解选择性为85%.Ru/C和Pd/C催化剂上裂解选择性分别为40%和69%.采用碳热还原方法制备的Ni/C-C催化剂,可以实现高选择性加氢和裂解,C-O-C键裂解选择性达到99%以上,其中芳烃化合物收率为44%.这可能与镍组分和载体碳之间的相互作用有关.     

Comparative characteristics of cathodes with different catalytic systems in hydrogen–oxygen and hydrogen–air fuel cells with proton-conducting polymer electrolyte

The characteristics of low-temperature hydrogen–oxygen (air) fuel cell (FC) with cathodes based on the 50 wt % PtCoCr/C and 40 wt % Pt/CNT catalysts synthesized on XC72 carbon black and carbon nanotubes (CNT) are compared with the characteristics of commercial monoplatinum systems 9100 60 wt % Pt/C and 13100 70% Pt/C HiSPEC. It is shown that the synthesized catalysts exhibit a high mass activity, which is not lower than that of commercial Pt/C catalysts, a high selectivity with respect to the oxygen reduction to water, and a significantly higher stability. The characteristics of PtCoCr/C and Pt/CNT were confirmed by testing in the hydrogen—oxygen FCs. However, when air was used at the cathode, especially in the absence of excessive pressure, a voltage of FC with the cathode based on PtCoCr/XC72 is lower as compared with the commercial systems. Probably, this is associated with the transport limitations in the structure of trimetallic catalyst synthesized on XC72 carbon black due to the absence of mesopores. This drawback was eliminated to a large extent by raising the volume of mesopores as a result of application of mixed support (XC72 + CNT) and the use of only CNT for the synthesis of the monoplatinum catalyst. However, this did not eliminate another drawback, namely, a low platinum utilization coefficient in the cathode active layer as compared with that measured under the model conditions in the 0.5 M Н₂SO₄ solution. Therefore, further research is required to improve the structure of the catalytic systems, which are synthesized both on carbon black and nanotubes, while maintaining their high stability and selectivity.     

锂嵌入型化合物-氢气电池

可充电氢气电池作为一种新兴的电池体系在大规模能源储存领域显示出富有前景的电化学性能. 锂嵌入型化合物作为一大类的锂离子电池正极材料能够很好地用作可充电氢气电池的正极. 本文开发了 2种新型锂嵌入型化合物-氢气电池. 通过使用钴酸锂与磷酸铁锂2种正极材料分别与氢气负极在硫酸锂 水系电解液中进行匹配, 得到了钴酸锂-氢气电池与磷酸铁锂-氢气电池. 钴酸锂-氢气电池展现出约1.27 V 的放电电位, 约97 mA·h·g^-1的比容量及10C的高倍率; 磷酸铁锂-氢气电池展现出约0.66 V的放电电位, 约125 mA·h·g^-1的比容量以及10C的高倍率. 虽然, 钴酸锂-氢气电池和磷酸铁锂-氢气电池因为使用了未经优化的、 不稳定的锂嵌入型化合物正极材料而导致全电池容量衰减, 但这2种电池经过氢气负极的再循环利用均表现出优异的恢复能力. 本文结果证明了氢气电池的化学稳定性及其在未来长寿命电池中具有的大规模能源储存潜力.     

Pd nanoparticles supported on CeO2 as efficient catalyst for hydrogen generation from formaldehyde solution at room temperature

A facile and efficient method for facilitating hydrogen generation from formaldehyde aqueous solution was developed using Pd nanoparticles supported on CeO₂ (Pd/CeO₂) as the catalyst. The prepared Pd/CeO₂ catalyst exhibited 100% H₂ selectivity and excellent catalytic activity for formaldehyde dehydrogenation with the initial rate of 2089 ml min⁻¹ g_Pd⁻¹ at room temperature and atmospheric pressure without any extra additive. The prepared catalyst was stable and reusable, and its catalytic activity kept almost unchanged after it was reused for the fifth run. Therefore, it is considered that this Pd/CeO₂ based hydrogen generation system may serve as an alternative hydrogen supply candidate for practical application.     

Bismuth modified Pd/C as catalysts for hydrogen related reactions

The electrocatalytic activity of bimetallic BiPd catalysts supported on Sibunit carbon towards hydrogen oxidation/evolution reactions (HOR/HER) was studied in a gas diffusion electrode (GDE) setup. Catalysts were synthesized by deposition of Pd on the carbon support, followed by impregnation of Pd/C precursor with Bi(NO₃)₃ solution and reduction in hydrogen. Transmission electron microscopy and local EDX elemental analysis revealed that BiPd/C catalysts contain bimetallic particles with narrow size distribution with maxima at 3.2–4.1 nm. X-ray diffraction evidenced that bimetallic particles are constituted by Pd–Bi solid solution. It was shown that modification of Pd/C by bismuth increases the specific activity of palladium towards HOR/HER by a factor of 3.     

Cost-effective bio-derived mesoporous carbon nanoparticles-supported palladium catalyst for nitroarene reduction and Suzuki–Miyaura coupling by microwave approach

A new heterogeneous catalyst was synthesized by immobilizing Pd on areca nut kernel-derived carbon nanospheres (CNSs). The CNSs, without any further activation processes, accommodated 3% of Pd on their surface. The new Pd/CNS material was used for the reduction of nitroarenes and Suzuki–Miyaura coupling of bromoarenes with aryl boronic acids. The reactions were conducted under microwave irradiation at 160 °C using 12 mol% of Pd/CNS (0.36% actual Pd content). The reduction of nitroarenes into their respective amino compounds was achieved in 10–20 min (conversion up to 100%); by contrast, the Suzuki–Miyaura reactions yielded up to 98% at 150 °C with 10 mol% of Pd/CNS catalyst. The products were identified using gas chromatography and nuclear magnetic resonance spectroscopy. The catalyst was isolated from reaction mixture and reused without any significant loss in the activity. Thus, the present work introduces one-pot-derived porous CNSs as efficient catalytic support to Pd, establishing an alternative to existing Pd/C in terms of cost and efficiency.     

炭载Pd-Fe合金催化剂的制备及电催化氧还原活性

研究了用NH4Cl作配位剂的配位还原法来制备的Pd-Fe/C催化剂,发现由于NH4Cl能与Pd形成配合物,使Pd Cl2的还原电位负移,与Fe Cl3的还原电位接近,从而在低温下制备得到了高合金化程度的Pd-Fe/C催化剂。XPS表征结果表明:Pd与Fe形成合金后,Pd的电荷密度的减少,增加了Pd0的含量。因此,得到的Pd-Fe/C催化剂对氧还原的电催化活性比用相同方法制得的Pd/C催化剂高,而且该催化剂对甲醇氧化没有电催化活性。     

炭载Pd-Fe合金催化剂的制备及电催化氧还原活性

研究了用NH₄Cl作配位剂的配位还原法来制备的Pd-Fe/C催化剂,发现由于NH₄Cl能与Pd形成配合物,使PdCl₂的还原电位负移,与FeCl₃的还原电位接近,从而在低温下制备得到了高合金化程度的Pd-Fe/C催化剂。XPS表征结果表明:Pd与Fe形成合金后,Pd的电荷密度的减少,增加了Pd⁰的含量。因此,得到的Pd-Fe/C催化剂对氧还原的电催化活性比用相同方法制得的Pd/C催化剂高,而且该催化剂对甲醇氧化没有电催化活性。     

Meso-structured platinum thin films: active and stable electrocatalysts for the oxygen reduction reaction

Improving both the activity and the stability of the cathode catalyst in platinum-based polymer electrolyte fuel cells is a key technical challenge. Here, we synthesize a high surface area meso-structured Pt thin film that exhibits higher specific activity for the oxygen reduction reaction (ORR) than commercial carbon-supported Pt nanoparticles (Pt/C). An accelerated stability test demonstrates that the meso-structured Pt thin film also displays significantly enhanced stability as compared to the commercial Pt/C catalyst. Our study reveals the origin of the high turnover frequency (TOF), and excellent durability is attributed to the meso-structure, which yields a morphology with fewer undercoordinated Pt sites than Pt/C nanoparticles, a key difference with substantial impact to the surface chemistry. The improved catalyst activity and stability could enable the development of a high-performance gas diffusion electrode that is resistant to corrosion even under the harsh conditions of start-up, shut-down, and/or hydrogen starvation.     

Fe修饰多壁碳纳米管电极高效产H2O2

为提高电芬顿(Electro-Fenton)体系H2O2的产率, 制备了多壁碳纳米管(MWNT)电极, 并与石墨/气体扩散(GDC)电极进行了比较. 结果表明, MWNT电极H2O2产率高于GDC电极. 采用电沉积方法, 制备了Fe修饰MWNT(Fe-MWNT)电极, 发现Fe对MWNT电极的修饰不仅可以提高体系的H2O2产率, 而且电流效率可以提高8%左右, 与GDC电极的电流效率接近. Fe-MWNT电极有望成为一种新型的阴极材料应用于Electro-Fenton体系中.