Electrochemical performance of LiNi0.5Mn1.5O4 doped with la and its compatiblity with new electrolyte system

Cathode materials LiNi_0.5Mn_1.5O₄ and LiNi_{0.5 ? x/2}La _x Mn_{1.5 ? x/2}O₄ (x = 0.04, 0.1, 0.14) were successfully prepared by the sol-gel self-combustion reaction (SCR) method. The X-ray diffraction (XRD) patterns indicated that, a few of doping La ions did not change the structure of LiNi_0.5Mn_1.5O₄ material. The scanning electronic microscopy (SEM) showed that the sample heated at 800°C for 12 h and then annealed at 600°C for 10 h exhibited excellent geometry appearance. A novel electrolyte system, 0.7 mol L^?1 lithium bis(oxalate)borate (LiBOB)-propylene carbonate (PC)/dimethyl carbonate (DMC) (1: 1, v/v), was used in the cycle performance test of the cell. The results showed that the cell with this novel electrolyte system performed better than the one with traditional electrolyte system, 1.0 mol L^?1 LiPF₆-ethylene carbonate (EC)/DMC (1: 1, v/v). And the electrochemical properties tests showed that LiNi_0.45La_0.1Mn_1.45O₄/Li cell performed better than LiNi_0.5Mn_1.5O₄/Li cell at cycle performance, median voltage, and efficiency.     

Effect of sulfolane on the morphology and chemical composition of the solid electrolyte interphase layer in lithium bis(oxalato)borate‐based electrolyte

To discuss the source of sulfolane (SL) in decreasing the interface resistance of Li/mesophase carbon microbeads cell with lithium bis(oxalate)borate (LiBOB)‐based electrolyte, the morphology and the composition of the solid electrolyte interphase (SEI) layer on the surface of carbonaceous anode material have been investigated. Compared with the cell with 0.7 mol l^?1 LiBOB‐ethylene carbonate/ethyl methyl carbonate (EMC) (1 : 1, v/v) electrolyte, the cell with 0.7 mol l^?1 LiBOB‐SL/EMC (1 : 1, v/v) electrolyte shows better film‐forming characteristics in SEM (SEI) spectra. According to the results obtained from Fourier transform infrared spectroscopy, XPS, and density functional theory calculations, SL is reduced to Li₂SO₃ and LiO₂S(CH₂)₈SO₂Li through electrochemical processes, which happens prior to the reduction of either ethylene carbonate or EMC. It is believed that the root of impedance reduction benefits from the rich existence of sulfurous compounds in SEI layer, which are better conductors of Li⁺ ions than analogical carbonates. Copyright © 2013 John Wiley & Sons, Ltd.     

An enhanced poly(vinylidene fluoride) matrix separator with high density polyethylene for good performance lithium ion batteries

A sponge-like poly(vinylidene fluoride)/high density polyethylene (PVDF/HDPE) separator exhibiting high ionic conductivity and transference number of Li⁺ ion for lithium ion battery has been prepared by non-solvent induced phase separation (NIPS) method. HDPE fillers with size smaller than 250 nm are prepared with moderated reverse phase emulsion. The ion conductivity of PVDF/HDPE separator saturated with 1.0 M LiPF₆–ethylene carbonate (EC)/dimethyl carbonate (DMC)/ethyl methyl carbonate (EMC) (1:1:1, v/v/v) can be up to 2.54 mS cm^?1 at 25 °C, which is higher than that of pristine PVDF separator (1.85 mS cm^?1). The transference number of lithium ion with PVDF/HDPE separator is 0.495, better than that with commercial PP separator (0.33) and pristine PVDF separator (0.27). What is more, LiCoO₂/Li cells assembled with PVDF/HDPE separator show good C-rate and cycling performance which indicates great potential in serving as a good candidate of polymer separator for lithium ion batteries application.     

Conductivity of LiBOB in various ternary solvent blends and the electrochemical performance of LiBOB-PC/EMC/DMC used in Li/MCMB and LiFePO4/Li cells

The solid-state reaction was employed to obtain LiBOB in vacuum dryer at 100°C, with the dryer of P₂O₅. The resulting LiBOB was employed in various ternary solvent blends to get the k, and its change with salt, solvent composition and temperature. 0.7 M LiBOB-PC/EMC/DMC (1: 1: 1, v: v: v) and 0.5 M LiBOB-EC/EMC/DMC (1: 1: 1, v: v: v) were observed to have better k at wide θ range, and the former was chosen to assemble Li/MCMB and LiFePO₄/Li cells. The results indicated that it can stabilize the MCMB anodes, and exhibit good stability in LiFePO₄/Li cell. Published in Russian in Elektrokhimiya, 2008, Vol. 44, No. 10, pp. 1231–1236. The text was submitted by the authors in English.     

The effects of substituting groups in cyclic carbonates for stable SEI formation on graphite anode of lithium batteries

Monofluoropropylene carbonate (MFPC) and trifluoropropylene carbonate (TFPC) with a monofluoromethyl (or trifluoromethyl) replacing the methyl group in propylene carbonate (PC) as well as EC-CH₂CH₂Si(CH₃)₂OSi(CH₃)₃ (Si-A) and EC-CH₂CH₂Si(CH₃)₃ (Si-B) have been synthesized. The charge–discharge studies in a Li/MCMB (mesocarbon microbeads) cell using electrolyte containing these compounds show that the solid electrolyte interphase (SEI) formation capability of MFPC/DMC (dimethyl carbonate) and TFPC/DMC are about the same as ethylene carbonate (EC)/DMC, and TFPC/PC/DMC is better than that of EC/PC/DMC, while MFPC/PC/DMC is poorer than the EC/PC/DMC. The superior SEI formation capability of TFPC could be attributed to the strong electron withdrawing group of CF₃, which promote the “ring-opening” reaction. In contrast, the electron donating group CH₃ in the PC structure may demote the “ring opening” and cause the poor SEI formation. The results of MFPC with weaker electron withdrawing group give further support of this hypothesis. The bi-solvent electrolytes of Si-A/DMC and Si-B/DMC have comparable SEI formation capability as EC/DMC and TFPC/DMC, regardless of their bulky chains. This indicates that if proper chain structures are used, good SEI formation capability could be obtained for cyclic carbonate with bulky chains. These new solvents provide valuable information in studying the SEI formation mechanism and designing new electrolytes.     

Intermediate phases during alkali metal intercalation in HfNCl

The mechanism of the chemical and electrochemical alkali metal intercalation reactions in β-HfNCl has been investigated through electrochemical potential spectroscopy (EPS), in-situ powder X-ray diffraction during electrochemical intercalation and room temperature chemical intercalation experiments. EPS experiments in lithium cells reveal the presence of a plateau, at 1.8 V vs. Li⁺/Li⁰ accounting for ca. 0.14 mol Li, that indicates the formation of a new intermediate phase, and then a gradual decrease of potential with composition that extends up to very high lithium contents (ca. 1.1 per formula), consistent with the formation of a solid solution. Sodium electrochemical intercalation experiments showed a relatively similar behaviour with a plateau at 1.4 V vs. Na⁺/Na⁰, corresponding to ca. 1.7 V vs. Li⁺/Li⁰. In-situ monitored powder X-ray diffraction electrochemical intercalation experiments showed that the electrolyte solvent (ethylene carbonate/dimethyl carbonate, EC/DMC or propylene carbonate, PC) co-intercalated with the alkaline atom. This leads to a large expansion of the interlayer spacing that reaches a value of 21.06 Å in the lithium co-intercalated phase with EC/DMC, Li_x(EC/DMC)_yHfNCl, and 22.01 Å in the sodium co-intercalated phase with PC, Na_x(PC)_yHfNCl. Chemical intercalation using naphthyl-sodium solutions in tetrahydrofuran (THF) leads to solvent-free, multiple-phase samples showing in different proportions the pristine and the superconducting stage 2 and stage 1 phases. The composition of the intercalated samples depends on the pristine sample, the concentration of the naphthyl-sodium solution, the ratio Na:HfNCl and the reaction time. Pristine samples exhibiting low lithium intercalation degree upon electrochemical reduction gave the second stage as the major phase when treated with short reaction times or using low Na:HfNCl ratios, coexisting either with the host or with the first stage phase, whereas stage 1 is obtained as the major phase from pristine samples showing high electrochemical capacities. The staging behaviour and the multiphase nature of these samples account for the wide superconducting transitions and the different critical temperatures observed in these superconductors.     

A new approach toward improved low temperature performance of Li-ion battery

We report a new approach toward formulating an electrolyte for low temperature operation of Li-ion batteries. The core of this new approach is to use LiBF₄ salt instead of LiPF₆, which is the chosen solute in the state-of-the-art Li-ion electrolytes. We found that although LiBF₄-based electrolyte has lower ionic conductivity than the LiPF₆ analogue, it provides improved low temperature performance. In particular, at −30 °C, a Li-ion cell with 1 m (mol/kg solvent) LiBF₄ dissolved in 1:1:3 (wt.) propylene carbonate (PC)/ethylene carbonate (EC)/ethylmethyl carbonate (EMC) mixed solvent delivers as high as 86% of capacity, in comparison to that obtained at 20 °C. Whereas the counterpart one, using LiPF₆, only retains 72%. Furthermore, the cell with LiBF₄-based electrolyte shows lower polarization at −30 °C. The above results suggest that the ionic conductivity of the electrolyte is not the only limitation to the low temperature operation of Li-ion batteries. Analysis of cell impedance reveals that the improved low temperature performance by LiBF₄ arises from a reduced charge-transfer resistance.     

锂离子电池正极材料LiNi_(1/3)Co_(1/3)Mn_(1/3)O_2在不同电解液中的性能研究

应用低热固相合成法制备锂离子电池正极材料L iCo1/3N i1/3Mn1/3O2.研究该材料的结构与形貌,并比较它在商品L iPF6盐和在实验室合成的L iBOB(L iB(C2O4)2)盐电解液中的电化学性能.在L iPF6/EC+DMC+DEC电解液中,该材料表现出优良的电化学性能,其于0.5C、1C、1.5C、2C、3C放电倍率的初始比容量依次为167、163、163、157、147mAh/g,电池的循环性能也较好,说明低热固相合成的材料的有较好的高倍率性能.在L iBOB/EC+DEC+DE电解液中,0.5C倍率下比容量为160 mAh/g,较之L iPF6盐电解液的相差不大,但在高倍率下的比容量有所下降.     

Electrolyte systems for primary lithium-fluorocarbon power sources and their working efficiency in a wide temperature range

New compositions of liquid organic electrolytes with working temperatures of up to–50°С were developed for low-temperature primary Li/CF _x power sources. Five different compositions of organic electrolytes with a 15-crown-5 (2 vol %) addition and without it were studied on laboratory Li/CF _x power sources. 1МLiBF₄ (LiPF₆) in an ethylene carbonate/dimethyl carbonate/methyl propionate/ethylmethyl carbonate (EC/DMC/MP/EMC) (1: 1: 1: 2) mixture and 1 М LiPF6 in an EC/DMC/EMC (1: 1: 3) mixture each with a 15-crown-5 (2 vol %) addition were found to be the best compositions of organic electrolytes with working temperatures of up to–50°С. The electrochemical tests at 20 and–50°С in the Li/CF _x system showed that the 15-crown-5 addition increased the length of the discharge plateau at–50°С three- or fourfold. The mechanisms responsible for the increase in the discharge capacity of the CF _x cathode in the presence of a crown ether addition were suggested.     

电解液添加剂硫酸亚乙酯对锂离子电池性能的影响

在1 mol/L LiPF₆/碳酸乙烯酯+碳酸二甲酯+碳酸甲乙酯（体积比1∶1∶1）电解液中,采用恒流充放电测试、循环伏安法（CV）、扫描电子显微镜（SEM）、能量散射光谱（EDS）、电化学阻抗谱（EIS）等测试技术,研究了添加剂硫酸亚乙酯（DTD）对锂离子电池性能及石墨化中间相碳微球（MCMB）电极/电解液界面性质的影响。 结果表明,在电解液中引入体积分数0.01%DTD后,MCMB/Li电池可逆放电容量从300 mA·h/g提高至350 mA·h/g,电池总阻抗降低,循环稳定性提高。CV测试发现,在首次还原过程中,DTD在电极电位1.4 V左右（vs Li/Li⁺）发生电化学还原,参与了MCMB电极表面固体电解质相界面膜（SEI膜）的形成过程。 同时,DTD对LiMn₂O₄电极性能无不良影响。     

Effect of plasticizers (EC or PC) on the ionic conductivity and thermal properties of the (PEO)9LiTf: Al2O3 nanocomposite polymer electrolyte system

A new plasticized nanocomposite polymer electrolyte based on poly (ethylene oxide) (PEO)-LiTf dispersed with ceramic filler (Al₂O₃) and plasticized with propylene carbonate (PC), ethylene carbonate (EC), and a mixture of EC and PC (EC+PC) have been studied for their ionic conductivity and thermal properties. The incorporation of plasticizers alone will yield polymer electrolytes with enhanced conductivity but with poor mechanical properties. However, mechanical properties can be improved by incorporating ceramic fillers to the plasticized system. Nanocomposite solid polymer electrolyte films (200–600 μm) were prepared by common solvent-casting method. In present work, we have shown the ionic conductivity can be substantially enhanced by using the combined effect of the plasticizers as well as the inert filler. It was revealed that the incorporating 15 wt.% Al₂O₃ filler in to PEO: LiTf polymer electrolyte significantly enhanced the ionic conductivity [σ _RT (max)?=?7.8?×?10^?6 S cm^?1]. It was interesting to observe that the addition of PC, EC, and mixture of EC and PC to the PEO: LiTf: 15 wt.% Al₂O₃ CPE showed further conductivity enhancement. The conductivity enhancement with EC is higher than PC. However, mixture of plasticizer (EC+PC) showed maximum conductivity enhancement in the temperature range interest, giving the value [σ _RT (max)?=?1.2?×?10^?4 S cm^?1]. It is suggested that the addition of PC, EC, or a mixture of EC and PC leads to a lowering of glass transition temperature and increasing the amorphous phase of PEO and the fraction of PEO-Li⁺ complex, corresponding to conductivity enhancement. Al₂O₃ filler would contribute to conductivity enhancement by transient hydrogen bonding of migrating ionic species with O–OH groups at the filler grain surface. The differential scanning calorimetry thermograms points towards the decrease of T _g , crystallite melting temperature, and melting enthalpy of PEO: LiTf: Al₂O₃ CPE after introducing plasticizers. The reduction of crystallinity and the increase in the amorphous phase content of the electrolyte, caused by the filler, also contributes to the observed conductivity enhancement.     

Synthesis and electrochemical properties of activated carbons and Li4Ti5O12 as electrode materials for supercapacitors

New activated nanoporous carbons, produced by carbonization of mixtures of coal tar pitch and furfural with subsequent steam activation, as well as electrochemically active oxide Li₄Ti₅O₁₂, prepared by thermal co-decomposition of oxalates, were tested and characterized as electrode materials for electrochemical supercapacitors. The phase composition, microstructure, surface morphology and porous structure of the materials were studied. Pure carbon electrodes as well as composite electrodes based on these materials obtained were fabricated. Two types of supercapacitor (SC) cells were assembled and subjected to charge–discharge cycling study at different current rates: (1) symmetric sandwich-type SC cells with identical activated carbon electrodes and different organic electrolytes, and (2) asymmetric hybrid SC cell composed by activated graphitized carbon as a negative electrode and activated carbon–Li₄Ti₅O₁₂ oxide composite as a positive electrode, and an organic electrolyte (LiPF₆–dimethyl carbonate/ethylene carbonate (DMC/EC). Four types of carbons with different specific surface area (1,000–1,600 m² g^?1) and texture parameters, as well as three types of organic electrolytes: Et₄NBF₄–propylene carbonate (PC), LiBF₄–PC and LiPF₆–DMC/EC in the symmetric SC cell, were tested and compared with each other. Capacitance value up to 70 F g^?1 for the symmetric SC, depending on the electrolyte microstructure and conductivity of the carbon material used, and capacitance of about 150 F g^?1 for the asymmetric SC cell, with good cycleability for both supercapacitor systems, were obtained.     

A density functional theory investigation on the mechanism and kinetics of dimethyl carbonate formation on Cu2O catalyst

A theoretical analysis about the mechanism and kinetics of dimethyl carbonate (DMC) formation via oxidative carbonylation of methanol on Cu₂O catalyst is explored using periodic density functional calculations, both in gas phase and in solvent. The effect of solvent is taken into account using the conductor‐like screening model. The calculated results show that CO insertion to methoxide species to produce monomethyl carbonate species is the rate‐determining step, the corresponding activation barrier is 161.9 kJ mol^?1. Then, monomethyl carbonate species reacts with additional methoxide to form DMC with an activation barrier of 98.8 kJ mol^?1, above reaction pathway mainly contributes to the formation of DMC. CO insertion to dimethoxide species to form DMC is also considered and analyzed, the corresponding activation barrier is 308.5 kJ mol^?1, suggesting that CO insertion to dimethoxide species is not competitive in dynamics in comparison with CO insertion to methoxide species. The solvent effects on CO insertion to methoxide species involving the activation barriers suggest that the rate‐determining step can be significantly affected by the solvent, 70.2 kJ mol^?1 in methanol and 63.9 kJ mol^?1 in water, which means that solvent effect can reduce the activation barrier of CO insertion to methoxide species and make the reaction of CO insertion to methoxide in solvents much easier than that in gas phase. Above calculated results can provide good theoretical guidance for the mechanism and kinetics of DMC formation and suggest that solvent effect can well improve the performance of DMC formation on Cu₂O catalyst in a liquid‐phase slurry. © 2012 Wiley Periodicals, Inc.     

Association constants in solutions of lithium salts in butyrolactone and a mixture of propylene carbonate with 1,2-dimethoxyethane (1 : 1), according to conductometric data

A conductometric study is performed with solutions of lithium bis(oxalato)borate (LiBOB) in γ-butyrolactone (γ-BL) at 278.15–388.15 K and lithium bis(trifluoromethylsulfonyl)imide (LiTFSI), LiBOB, and lithium tetrafluoroborate (LiBF₄) in mixtures of propylene carbonate and 1,2-dimethoxyethane (PC + 1,2-DME) (1 : 1) at 278.15–348.15 K. Limiting molar electrical conductivities (LMECs) and association constants (K a) in the studied solutions of electrolytes are determined using the Lee–Wheaton equation. The effect temperature, the nature of the solvent, and the properties of the anion have on the conductivity and interparticle interactions in solutions of lithium salts in γ-BL and PC + 1,2-DME (1 : 1) is established. It was concluded that the studied solutions are characterized by low values of their association constants. It was found that the ВОВ^– anion destroys the structure of the solvent.The thickness of the dynamic solvation shell of ions (ΔR) remains constant for both solvents over the studied range of temperatures, and ΔR is significantly greater for Li⁺ than for other ions.     

PVDF/PMMA brushes membrane for lithium‐ion rechargeable batteries prepared via preirradiation grafting technique

Poly(methyl methacrylate) (PMMA) was anchored to multiporous poly(vinylidine fluoride) (PVDF) surface via electron beam preirradiation grafting technique to prepare PVDF/PMMA brushes. The conformation of the PVDF/PMMA brushes was verified through Attenuated total reflection‐Fourier transform infra red spectroscopy (ATR‐FTIR), energy dispersive X‐ray spectroscopy (EDX), and scanning electron microscopy (SEM). Thermal stability of PVDF/PMMA brushes was characterized by thermo gravimetric analysis (TGA). The degradation of PVDF/PMMA brushes showed a two‐step pattern. PVDF/PMMA brushes membrane could be used as polymer electrolyte in lithium‐ion rechargeable batteries after it was activated by uptaking 1 M LiPF₆/EC‐DMC (ethylene carbonate/dimethyl carbonate; EC:DMC = 1:1 by volume) electrolyte solution. The activated membrane showed high ionic conductivity, 6.1 × 10^?3 S cm^?1 at room temperature, and a good electrochemical stability up to 5.0 V. The excellent performances of multiporous PVDF‐g‐PMMA membranes suggest that they are suitable for application in high‐performance lithium‐ion batteries. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 751–758, 2008     

Kinetic study of the reaction of dimethyl carbonate with trialkylamines

Quaternary ammonium compounds are produced worldwide in hundreds of millions of pound volume annually for a plethora of end‐uses from fabric‐care formulations to asphalt emulsifiers, typically from nongreen alkylating reagents. The kinetics of a reaction employing dimethyl carbonate (DMC) as a green alkylating agent was investigated using three trialkylamines (tributylamine, trihexylamine, and trioctylamine) at several temperatures. Arrhenius and Eyring analysis of the data showed that values of E_a (79 kJ/mol), ΔH^? (75 kJ/mol), and ΔS^? (220 J/(mol K)) were the same for all three amine reactants, consistent with a report that E_a is independent of alkyl chain length when the chain length is greater than three carbons. Although rates are significantly slower with DMC than with other alkylating reagents, the resulting methyl carbonate anion has advantages for clean anion metathesis, which is important for some applications, especially those involving ionic liquids. © 2010 Wiley Periodicals, Inc. Int J Chem Kinet 42: 221–225, 2010     

Resolution of Racemic Ofloxacin Based on Co-Technology of Bubble Fractionation and Extraction

A method of bubble fractionation, with the help of solvent extraction, was developed for the resolution of racemic ofloxacin (rac OFLX). In this method, dibenzoyl-L-tartaric (L-DBTA), di-(2-ethylhexyl) phosphoric acid (D2EHPA) and sodium lauryl sulfate (SDS) were used as chiral collector, co-extractant and foamer, respectively. Several important parameters influencing the resolution performances, such as pH in aqueous phase, concentration of OFLX, concentration of L-DBTA, concentration of SDS and volume ratio of D2EHPA to n-octanol in solution, were investigated. The optimal resolution conditions were obtained with the aqueous phase pH 7, volume ratio of D2EHPA to n-octanol 6/14 in organic phase, concentration of SDS 0.42 mg mL^?1, concentration of OFLX 1.67 mg mL^?1, and concentration of L-DBTA 0.11 g mL^?1. Under the optimal extraction conditions, the enantiomeric excess value (e.e.%) was 60.08% and the enantioselectivity (??) was 5.58. It was found that the capacity of enantioselective separation can be greatly improved by the co-technology.     

UV-light induced photodegradation of bisphenol a in water: Kinetics and influencing factors

The synthesis of dimethyl carbonate (DMC) from methanol and ethylene carbonate (EC) without using any solvent was investigated in the presence of ionic liquids as catalysts. The conversion of ethylene carbonate was affected by the structure of ionic liquid. For a series of 1-alkyl-3-methylimidazolium ionic liquids, the one with shorter alkyl chain and the one with more nucleophilic anion showed higher reactivity. The conversion of EC also increased with CO₂ pressure and reaction temperature. Esterification of EC and methanol can be considered as a pseudo-first order reaction with respect to EC concentration. The activation energy was estimated as 50.1 kJ/mol.     

Complex Formation Equilibria of Unusual Seven-Coordinate Fe(EDTA) Complexes with DNA Constituents and Related Bio-relevant Ligands

Seven-coordinate Fe(EDTA)?CL complexes, where L represents a DNA constituent (uracil, uridine, thymine, thymidine and inosine), methylamine, ammonium chloride or imidazole, were investigated to resolve the solution chemistry of this system. The results show formation of 1:1 complexes with DNA constituents and the other ligands, supporting the hepta-coordination mode of Fe(III) ion. Stability constants of the complexes were measured by potentiometric titration at 25?°C and ionic strength 0.1 mol?L^?1 NaNO₃. The hydrolysis constant of [Fe(EDTA)(H₂O)]^? and the formation constants of the complexes formed in solution were calculated using the non-linear least-squares program MINIQUAD-75. The concentration distributions of the various complex species were evaluated as a function of?pH. The thermodynamic parameters ??H ⁰ and ??S ⁰, calculated from the temperature dependence of the equilibrium constants, were determined for the Fe(EDTA)?Curacil complex. The effect of dioxane as a solvent on the protonation constant of uracil, hydrolysis constants of [Fe(EDTA)(H₂O)]^?, and the formation constants of the Fe(EDTA)?Curacil complex are discussed.     

Spectrophotometric study of competitive complexation equilibria involving overlapped spectral responding species: Determination of the stability constant of bismuth-pyrophosphate complex

Spectrophotometric study of competitive complex formation equilibria involving overlapped spectral responding species applying a simple and versatile algorithm was carried out. The algorithm involves multivariable regression for calculation of equilibrium concentrations from multiwavelength data and mass action law for the stability constant calculation. The used regression functions are part of common statistical software. Stability constants and complex stoichiometry of competing equilibria were simultaneously determined. The species concentration profiles at several spectral overlapping and ??-coefficient of competing reaction were obtained. Non-absorbing bismuth ?? pyrophosphate (PPh) system was studied as a competitive reaction of bismuth ?? 4-(2-Pyridylazo) resorcinol (PAR) complex. The formation of Bi-PPh complex with 1:1 stoichiometry was proved in the studied concentration region (C_Bi = 1×10^?5 mol L^?1; C_PPh = 5×10^?6 ? 1×10^?4 mol L^?1). The stability constant of the complex at pH 1 and ?? = 1.0 have been determined: log?? = 4.2±0.2.