Polymer surface science

Molecular level studies of the structure and mechanical properties of polymer surfaces have been carried out by sum frequency generation (SFG) surface vibrational spectroscopy and atomic force microscopy (AFM). The surfaces of different grades of polyethylene and polypropylene have been characterized-including during the glass transition and when mechanically stretched. Copolymers that have hard and soft segments with different glass transition temperatures show phase separation, an effect of hydrogen bonding between the hard and soft segments, that influences their adhesive and friction properties. AFM and SFG show that low surface energy additives migrate to the surface and alter the surface mechanical properties. Polymers, where the chemical nature of the end groups is different from the backbone, show surface segregation of the hydrophobic part of the chain in air and the hydrophilic part in water. Likewise, in miscible polymer blends, surface segregation of the more hydrophobic component in air and the more hydrophilic component in water is observed. This area of surface science requires increased attention because of the predominance of polymers as structural materials and as biomaterials.     

Probing the modifications of polystyrene surface properties after incubation with the Shewanella putrefaciens bacteria at two pH values (4, 10) by atomic force microscopy

The local surface properties of polystyrene (PS) dishes incubated for 14 h with gram‐negative cells (Shewanella putrefaciens) were investigated by atomic force microscopy (AFM) in aqueous solutions at two pH values (4 and 10). The AFM images and force curves revealed the presence of a polymeric layer adsorbed onto the PS surfaces in acid media. In contrast, no evolution was observed in the case of basic media. Copyright © 2007 John Wiley & Sons, Ltd.     

Observation of adhesive force and energy of adsorbents on rubber substrates by atomic force microscopy

We observed the surface morphology and adhesive interaction of adsorbents on rubber substrates by atomic force microscopy (AFM). The detachment of adsorbents from rubber substrates is an important issue for various machines like home appliances and laundry machine. Since a clean surface of the functioning parts is required, a frequent cleaning process must be developed. In particular, dust and lint have a tendency to bind to the rubber surface of a laundry machine. Several practical methods have been attempted to remove these particles from the surface. Pure water, detergent, sodium hypochlorite (65 °C), and cold water (18 °C) are treated onto artificial dust and lint mixtures on rubber with water fluid by rapid rpm. The dust‐and‐lint adsorbents are investigated by AFM after the treatment, and topographic images and force–distance (F–D) curves were generated for the samples. The roughness, measured as the root mean square, is a key factor to judge the cleaning quality. From the F–D curves, we are able to obtain adhesive energy in addition to adhesive force which will yield qualitative measures of the interactions between the remaining adsorbents and the rubber surface. Considering the values that were measured, hot water with water fluid by rapid rpm offers the best performance when cleaning the surface. The chemical like sodium hypochlorite is good for thinning the materials, but it solidifies them, which is eventually detrimental to proper functioning. Copyright © 2014 John Wiley & Sons, Ltd.     

Nanotechnological evaluation of protein adsorption on dialysis membrane surface hydrophilized with polyvinylpyrrolidone

Hydrophilizing synthetic polymer dialysis membranes with polyvinylpyrrolidone (PVP) play an important role for inhibition of protein adsorption on membrane surface. In the present study, the effect of PVP on protein adsorption was evaluated from a nano-scale perspective. Swelling behavior of PVP present on wet polysulfone (PS)/PVP film surfaces was observed by atomic force microscopy (AFM). Fibrinogen and human serum albumin (HSA) were immobilized on the tip of AFM probes, with which a force-curve between protein and wet PS/PVP film surface was measured by AFM while scanning in order to visualize two-dimensional protein adsorbability on film surfaces. Furthermore, HSA adsorbability on non-PVP containing PEPA dialysis membrane (FLX-15GW) and PVP containing PEPA dialysis membrane (FDX-150GW) was evaluated by the AFM force-curve method. As a result, PS/PVP film surface was completely covered with hydrated and swollen PVP at 5 wt% or more PVP content. Protein adsorbability on PS/PVP film surfaces decreased greatly with increasing content of PVP. The adsorption of HSA was inhibited by the presence of PVP on film surfaces more significantly than that of more hydrophobic fibrinogen. HSA adsorbability on wet FLX-15GW dialysis membrane surface was 428 ± 174 pN whereas that on wet FDX-150GW dialysis membrane surface was 42 ± 29 pN.     

Measuring forces with the AFM: polymeric surfaces in liquids

This review links together for the first time both the practicalities of force measurement and the work carried out to date on force detection between polymeric surfaces in liquids using the atomic force microscope (AFM). Also included is some of the recent work that has been carried out between surfactant surfaces and biologically coated surfaces with the AFM. The emphasis in this review is on the practical issues involved with force measurement between these types of surfaces, and the similarities and irregularities between the observed types of forces measured. Comparison is made between AFM and surface force apparatus (SFA) measurements, as there is a much longer history of work with the latter. Results indicate that forces between the surfaces reviewed here are a complicated mixture of steric-type repulsion, conformational behaviour on separation and long-range attraction, which is often ascribed to 'hydrophobic' forces. The origin of this latter force remains uncertain, despite its almost ubiquitous appearance in force measurements with these types of surfaces.     

Influence of attractive force on imaging micro‐droplets of water by atomic force microscope

The shape of micro‐droplets of water on a pure copper surface was investigated using the a.c. non‐contact mode of an atomic force microscope (AFM) by applying different attractive forces between the cantilever tip and the liquid surface. The forces largely influenced the observed radii of micro‐droplets; the influence can be reduced significantly by reducing the force. The same attractive force between the cantilever tip and the micro‐droplets is necessary when comparing the contact angles of micro‐droplets on different surfaces. Furthermore, the values of the contact angles of the micro‐droplets should be the average of those on at least four sides of the droplets. Copyright © 2005 John Wiley & Sons, Ltd.     

Determination of solid surface tension from particle-substrate pull-off forces measured with the atomic force microscope

Atomic force microscopy (AFM) is capable of solid surface characterization at the microscopic and submicroscopic scales. It can also be used for the determination of surface tension of solids (gamma) from pull-off force (F) measurements, followed by analysis of the measured F values using contact mechanics theoretical models. Although a majority of the literature gamma results was obtained using either Johnson-Kendall-Roberts (JKR) or Derjaguin-Muller-Toporov (DMT) models, re-analysis of the published experimental data presented in this paper indicates that these models are regularly misused. Additional complication in determination of gamma values using the AFM technique is that the measured pull-off forces have poor reproducibility. Reproducible and meaningful F values can be obtained with strict control over AFM experimental conditions during the pull-off force measurements (low humidity level, controlled and known loads) for high quality substrates and probes (surfaces should be free of heterogeneity, roughness, and contamination). Any probe or substrate imperfections complicate the interpretation of experimental results and often reduce the quality of the generated data. In this review, surface imperfection in terms of roughness and heterogeneity that influence the pull-off force are analyzed based upon the contact mechanics models. Simple correlations are proposed that could guide in selection and preparation of AFM probes and substrates for gamma determination and selection of loading conditions during the pull-off force measurements. Finally, the possibility of AFM measurements of solid surface tension using materials with rough surfaces is discussed.     

Atomic force microscopy study of salivary pellicles formed on enamel and glass in vivo

This study was performed to evaluate the use of atomic force microscopy (AFM) in examining the surface of the adsorbed layer of salivary proteins (salivary pellicle) formed in vivo on dental enamel and glass surfaces. Enamel and glass test pieces were attached to the buccal surfaces of the upper first molar teeth in two adults using removable intraoral splints. The splints were carried intraorally over periods ranging from 10 min to1 h. Using the contact mode of AFM, pellicle structures could be recognised on intraorally exposed specimens compared to nonexposed enamel and glass surfaces. The surface of the adsorbed salivary pellicle was characterised by a dense globular appearance. The diameter of the globulelike protein aggregates adsorbed onto enamel and glass varied between 80 and 200 nm and 80 and 150 nm, respectively. The structure of the adsorbed protein layer was clearly visible on glass surfaces, even though minor differences in the protein layer between glass and enamel specimens were observed. This study indicates that AFM is a powerful tool for high-resolution examination of the salivary pellicle surface structure in its native (hydrated) state. AFM avoids artefacts due to fixing, dehydration and sputter-coating which occur with scanning electron microscopic analyses. Received: 29 November 2000 Accepted: 14 December 2000     

Direct measurement of hydrophobic particle–bubble interactions in aqueous solutions by atomic force microscopy: Effect of particle hydrophobicity

Direct measurements of the interaction forces between a spherical silica particle and a small air bubble have been conducted in aqueous electrolyte solutions by using an atomic force microscope (AFM). The silica particle was hydrophobized with a silanating reagent, and the interaction forces were measured by using several particles with different surface hydrophobicities. In the measured force curves, a repulsive force was observed at large separation distances as the particle moved towards the bubble. The origin of the repulsive force was attributed to an electrostatic double-layer force because both the particle and bubble were negatively charged. After the repulsive force, an extremely long-range attractive force acted between the surfaces. These results indicate that the intervening thin water film between the particle and bubble rapidly collapsed, resulting in the particle penetrating the bubble.

The instability of the thin water film between the surfaces suggests the existence of an additional attractive force. By comparing the repulsive forces of the obtained force curves with the DLVO theory, the rupture thickness was estimated. The hydrophobicity of the particle did not significantly change the rupture thickness, whereas the pH of the solution is considered to be a critical factor.     

Particle adhesion in coagulation and bridging flocculation

The adhesive forces between solid particles mutually attached during coagulation or bridging flocculation are important for modelling floc stability. Results are presented in this study which are obtained from experiments on the adhesion of glass or quartz particles to a flat glass substrate (centrifugal method) or to the wall of a glass capillary through which an aqueous electrolyte solution was passed. Coagulation experiments carried out in 10^–2 mole/1 MgCl₂ showed the action of hydration layers on hydrophilic surfaces, whereas surface methylation is associated with adhesion in the inner potential minimum. In addition essential ageing effects interpreted as interparticle gelation were observed, especially on the interaction of alkali glass surfaces. Adhesive strength in the case of flocculation with hydrolysed polyacrylamide and a cationic Praestol mainly depends on the polymer concentration and on the preadsorption conditions before the particle-substrate attachment. A significant strengthening of adhesion due to reconformation of the bridging agents was not observed for a contact time greater than 3 min. The effect of steric stabilization with polymer overdosing could be proved by a special preparation technique.Publication no. 922 from the Research Institute of Mineral Processing of the Academy of Sciences of German Democratic Republic, Freiberg.     

Two-dimensional auto-organized nanostructure of sodium hyaluronate and its frictional properties

The two-dimensional auto-organized nanostructure of sodium hyaluronate NaHA on bovine serum albumin BSA monolayer was studied by a layer-by-layer method. The surface properties were studied by a quartz crystal microbalance QCM method and by using an atomic force microscope AFM. NaHA showed a Langmuir-type adsorption and was found to form honeycomb-like networks. With increasing adsorption amount of NaHA, their mesh size decreased and their strand size increased in width. The surface nanomechanical properties, such as adhesion force F_ad and frictional forces F_f between the surfaces of the NaHA layers and the AFM tip, were studied in air and in NaHA solutions using a contact mode and a lateral force modulation LFM of AFM. The values of F_ad and F_f obtained in air were found to be higher than those obtained in the solutions because of the effect of moisture film on the NaHA layers. The values of F_ad and frictional coefficients in the solutions increased with increasing .     

The role of few-asperity contacts in adhesion

The surface roughness of a few asperities and their influence on the work of adhesion is of scientific interest. Macroscale and nanoscale adhesion data have seemingly given inconsistent results. Despite the importance of bridging the gap between the two regimes, little experimental work has been done, presumably due to the difficulty of the experiment needed to determine how small amounts of surface roughness might influence adhesion data lying in between the two scales. To investigate the role of few-asperity contacts in adhesion, the pull-off force was measured between different sized atomic-force microscope (AFM) tips (with different roughnesses) and sample surfaces that had well-controlled material properties. There were seventeen tips of four different types, with radii from 200 nm to 60 microm. The samples were unpatterned single crystal silicon with a chemical silicon dioxide surface resulting from a standard silicon wafer clean. Some of the samples were treated with a few angstroms of vapor deposited diphenylsiloxane. We observed that the uncorrected (for surface roughness) pull-off force was independent of the radius of the AFM tip, which was contrary to all continuum-mechanics model predictions. To explain this behavior, we assumed that the interactions between the AFM tip and sample were additive, material properties were constant, and that the AFM tip, asperities, and sample surfaces were of uniform density. Based on these assumptions, we calculated a simple correction due to the measured root mean square (RMS) surface roughness of the AFM tips. The simple correction for the RMS surface roughness resulted in the expected dependence of the pull-off force on radius, but the magnitudes were higher than expected. Commercial and heat-treated AFM tips have minimal surface roughness and result in magnitudes that are more reliable. The relative uncertainty for the pull-off force was estimated to be 10%. In this paper, we derive how the cantilever and tip parameters contribute to the measured pull-off force and show how the corrected results compare with theory. Although much work is still needed, the work presented here should advance the understanding of adhesion between the macroscale and nanoscale regimes.     

A novel approach to investigate vascular wall in 3D: Combined Raman spectroscopy and atomic force microscopy for aorta en face imaging

A novel approach based on the combination of Raman confocal 3D imaging with atomic force microscopy (AFM) for analysis of the murine vessel wall en face is described. The approach is based on subsequent Raman and AFM imaging of the same areas of the sample. This methodology allows for direct correlation of the chemical structure (Raman data) with morphology of the surface (AFM). The sub-cellular structures of the tissue e.g., cell nuclei, heme, or lipid-rich species are visualized and localized by the application of Raman imaging, while AFM complements these data with high-resolution information about the surface topography and size of lipid-rich structures. Overall, the applied approach enables detailed characterization of the inner layer of the vessel wall.     

Synthesis of novel hybrid films of a layered silicate and alkylammonium cations on rough polymeric surfaces by Langmuir–Blodgett method

Hybrid films of a layered silicate and an amphiphilic alkylammonium (hexadecyltrimethylammonium) cation have been prepared by Langmuir–Blodgett (LB) method and transferred onto a polyamide surface by dip coating. This is the first time that stable LB hybrid monolayer and multilayer films have been formed on rough polymeric surfaces. The films were characterized by X-ray diffraction (XRD), fourier transform infrared spectroscopy (FTIR), atomic force microscopy (AFM) and water contact angle measurements. XRD and FTIR showed that the hybrid multilayer was well-organized and the thickness of one layer was calculated to be 1.6 nm. Furthermore, the layered silicate was determined to be on the substrate side and the amphiphilic molecule layer was exposed to the air side. This provides a novel methodology for the surface modification of polymers.     

Surface properties of Aspergillus oryzae spores investigated by atomic force microscopy

Spores of the filamentous fungus Aspergillus oryzae have a great biotechnological potential for the production of highly active proteins. To date, little is known about the molecular mechanisms of spore aggregation, a phenomenon observed during germination in liquid medium. Here, atomic force microscopy (AFM) imaging and force measurements were used to characterize, under aqueous conditions, the surface morphology and macromolecular interactions of A. oryzae spores in relation to their aggregation behavior. Dormant spores were covered with a discontinuous layer of about 35 nm thickness, as revealed by height images. High-resolution deflection images showed that this layer consisted of rodlets, 10±1 nm in diameter, that were assembled in parallel to form fascicles interlaced with different orientations. The germinating spore surface was much rougher and showed streaks oriented in the scanning direction, indicating that the probe was interacting with soft material. Retraction force curves were strikingly different depending on the spore physiological state: while dormant spores exhibited non-adhesive properties, germinating spores showed single or multiple attractive forces of 400±100 pN magnitude, along with characteristic elongation forces and rupture lengths ranging from 20 to 500 nm. These elongation forces are attributed to the stretching of long, flexible cell surface macromolecules and suggested to play a role in the aggregation process by promoting bridging interactions.     

Interactions between a polystyrene particle and hydrophilic and hydrophobic surfaces in aqueous solutions

The interaction between a colloidal polystyrene particle mounted on an AFM cantilever and a hydrophilic and a hydrophobic surface in aqueous solution is investigated. Despite the apparent simplicity of these two types of systems a variety of different types of interactions are observed. The system containing the polystyrene particle and a hydrophilic surface shows DLVO-like interactions characteristic of forces between charged surfaces. However, when the surface is hydrophobized the interaction changes dramatically and shows evidence of a bridging air bubble being formed between the particle and the surface. For both sets of systems, plateaus of constant force in the force curves are obtained when the particle is retracted from the surface after being in contact. These events are interpreted as a number of individual polystyrene molecules that are bridging the polystyrene particle and the surface. The plateaus of constant force are expected for pulling a hydrophobic polymer in a bad (hydrophilic) solvent. The plateau heights are found to be of uniform spacing and independent of the type of surface, which suggests a model by which collapsed polymers are extended into the aqueous medium. This model is supported by a full stretching curve showing also the backbone elasticity and a stretching curve obtained in pentanol, where the plateau changes to a nonlinear force response, which is typical for a polymer in a good or neutral solvent. We suggest that these polymer bridges are important in particular for the interaction between polystyrene and the hydrophilic surface, where they to some extent counteract the long-range electrostatic repulsion.     

Analysis of subcellular surface structure, function and dynamics

Analytics of single biological cells allows quantitative investigation from a structural, functional and dynamical point of view and opens novel possibilities to an unamplified subcellular analysis. In this article, we report on three different experimental methods and their applications to single cellular systems with a subcellular sensitivity down to the single molecule level. First, the subcellular surface structure of living bacteria (Corynebacterium glutamicum) was investigated with atomic force microscopy (AFM) at the resolution of individual surface layer (S-layer) proteins; discrimination of bacterial strains that lack the expression of hexagonally packed surface layer proteins was possible. Second, quantitative measurement of individual recognition events of membrane-bound receptors on living B-cells was achieved in single cell manipulation and probing experiments with optical tweezers (OT) force spectroscopy. And third, intracellular dynamics of translocating photoactivatable GFP in plant protoplasts (Nicotiana tabacum BY-2) was quantitatively monitored by two-photon laser scanning microscopy (2PLSM).     

Compositional Mapping of Polymer Surfaces by Chemical Force Microscopy Down to the Nanometer Scale: Reactions in Block Copolymer Microdomains

The laterally resolved analysis of the chemical surface composition of surface-treated block copolymers by atomic force microscopy (AFM) pull-off force mapping in the force volume (FV) mode and the automated analysis of the FV data is discussed. Poly(tert-butyl acrylate) (PtBA) microdomains residing in a polystyrene (PS) matrix at the surface of cyclohexane-treated polystyrene-block-poly(tert-butyl acrylate) (PtBA-b-PS) block copolymer thin films were domain-selectively deprotected, activated and chemically modified, as also shown by fluorescence microscopy. AFM pull-off force mapping in conjunction with an automated analysis of the data provided real space evidence for the successful conversion of reactive esters located in the PtBA domains and showed that AFM and related approaches, such as chemical force microscopy (CFM), can indeed contribute to assess changes in heterogeneous surface chemical composition of polymers down to sub-50 nm length scales.     

Correlating polymer structure,dynamics, and function with atomic force microscopy

Since its development, atomic force microscopy (AFM) has become an indispensable tool for investigating fundamental and technological applications of polymer materials. The versatility of AFM imaging modes and operating conditions allows for nanoscale characterization of a range of dynamic processes, such as crystallization, phase separation, self assembly, and electronic transport. Advances in AFM technology, particularly high-speed and high-resolution imaging, enable investigation of polymer structure, function, and dynamics in real world conditions and across a range of relevant spatial and temporal scales. In this perspective, we highlight a collection of recent polymer studies that utilize AFM to correlate the function and structure of polymer films, with focus on its multiparametric imaging capabilities. As the complexity of polymer materials and morphologies continues to increase, AFM is well poised to meet the accompanying demand for nanoscale imaging and characterization.     

Adsorption on stainless steel surfaces of biosurfactants produced by gram-negative and gram-positive bacteria: Consequence on the bioadhesive behavior of Listeria monocytogenes

The ability of adsorbed biosurfactants (Pf and Lb) obtained from gram-negative bacterium (Pseudomonas fluorescens) or gram-positive bacterium (Lactobacillus helveticus) to inhibit adhesion of four listerial strains to stainless steel was investigated. These metallic surfaces were characterized using the following complementary analytical techniques: contact-angle measurements (CAM), atomic force microscopy (AFM), polarization modulation-infrared reflection-adsorption spectroscopy (PM-IRRAS) and X-ray photoelectron spectroscopy (XPS). Contact-angles with polar liquids (water and formamide) indicated that the stainless steel surface covered with adsorbed biosurfactant was more hydrophilic and electron-donating than bare stainless steel. The surface characterization by XPS and PM-IRRAS revealed that conditioning the stainless steel changes the substrate in two ways, by modifying the surface alloy composition and by leaving an thin adsorbed organic layer. AFM observations enabled to say that the layer covered entirely the surface and was probably thicker (with patches) in the case of Pf-conditioned surfaces compared to the Lb-conditioned ones, which seemed to be less homogeneous. Though the added layer was thin, significant chemical changes were observed that can account for drastic modifications in the surface adhesive properties. As a matter of fact, adhesion tests showed that both used biosurfactants were effective by decreasing strongly the level of contamination of stainless steel surfaces by the four strains of Listeria monocytogenes. The more important decrease concerned the CIP104794 and CIP103573 strains (>99.7%) on surface conditioned by L. helveticus biosurfactant. A less reduced phenomenon (75.2%) for the CIP103574 strain on stainless steel with absorbed biosurfactant from P. fluorescens was observed. Whatever the strain of L. monocytogenes and the biosurfactant used, this antiadhesive biologic coating reduced both total adhering flora and viable and cultivable adherent bacteria on stainless steel surfaces. This study confirms that biosurfactants constitute an effective strategy to prevent microbial colonization of metallic surfaces by pathogenic bacteria like the food-borne pathogen L. monocytogenes.