共查询到20条相似文献,搜索用时 56 毫秒
1.
通过设计首次提出针对ITQ-13分子筛晶化促进剂的合成策略,ITQ-13分子筛.通过X射线粉末衍射(XRD)、扫描电子显微镜(SEM)、N2吸附、原位红外(FTIR)及固体核磁(27Al NMR)等测试手段对ITQ-13分子筛的物化性能进行了表征,考察了晶化过程中结晶度的变化,得出了晶化过程的动力学参数,对晶化机理进行了探讨.结果表明:快速合成法与传统方法合成的ITQ-13分子筛具有相似的物化性能,并且可以合成含有更多骨架铝的ITQ-13分子筛;NO3-的加入通过极化憎水基团,加速SiOSi物质结合,降低ITQ-13分子筛的成核活化能以及生长活化能,从而可以提高晶化速率,缩短晶化时间至11 h. 相似文献
2.
钛硅沸石的结晶动力学研究 总被引:8,自引:1,他引:7
在TPABr-正丁胺体系中合成了钛硅沸石TS-1, 研究了此体系中的结晶动力学,求出了不同温度下的成核速率、晶体生长速率及表观活化能. 还研究了晶种类型和用量对钛硅沸石晶化的影响. 结果表明,随着晶化温度的升高, TS-1成核诱导期缩短,成核速率及晶体生长速率加快; 加入晶种可明显缩短TS-1成核诱导期,并减小晶粒粒度; TS-1, M, ZSM-11和β沸石等均可作为晶种合成TS-1, 并存在一个最佳晶种用量; 不加晶种时TS-1成核活化能和晶体生长活化能分别为44.4和75.7 kJ/mol. 相似文献
3.
在强碱性水溶液体系中,以水玻璃为硅源,以铝酸钠为铝源,在类质同晶高硅P沸石晶种导向作用下,反应物中自发生成的A型沸石可转晶为纯相高铝MAP沸石。升高反应温度有利于提高产物的结晶度。由不同温度下的晶化曲线计算出MAP沸石表观生长活化能为59.6kJ.mol^-^1。不用晶种时,同一反应物体系结晶产物为单一的A型沸石。在该反应物体系中,A型沸石的成核活化能与生长活化能分别为40.3和50.7kJ.mol^-^1。MAP高的生长活化能以及A型沸石相对低的成核与生长活化能揭示合成MAP沸石时使用晶种的原因。 相似文献
4.
考察了用四乙基溴化铵-氟化钠复合模板剂合成β沸石的结晶动\r\n力学.结果表明:其晶化曲线为典型的S形曲线;成核活化能En=65.\r\n79kJ/mol,生长活化能Ec=91.49kJ/mol;与单纯的四乙基溴化铵模\r\n板剂体系相比,本体系成核诱导期较短,生长速率较快;n(NaF)/n\r\n(SiO2)值增大时,晶化诱导期缩短,成核速率加快,但氟化钠量过高\r\n时,成核速率反而降低,n(NaF)/n(SiO2)最佳值为0.10~0.17\r\n;较高的OH-/SiO2比有利于缩短晶化诱导期. 相似文献
5.
SAPO-11分子筛的合成 总被引:12,自引:0,他引:12
以二正丙胺(DPA)为模板剂、利用水热法合成SAPO-11分子筛,系统考察了硅源、硅含量、模板剂用量以及晶化条件(晶化温度、时间以及pH值)对SAPO-11分子筛合成的作用。研究结果表明:硅源是决定SAPO-11分子筛合成及结构的关键组分之一,其释放出活性硅物种的速率要与磷酸铝分子筛的前驱体生成的速度相一致;酸性硅溶胶是合成SAPO-11的合适硅源;在SiO2/Al2O3=0~0.7,DPA/P2O5=0.8~1.8,pH=5.8~7.8条件下,可合成纯SAPO-11分子筛。此外,SAPO-11分子筛的合成,还存在明显的诱导期以及晶型的转化过程。在合成条件下,晶化时间4?h时,SAPO-11开始晶化,至24 h,SAPO-11分子筛可晶化完全。继续延长晶化时间,SAPO-11分子筛与SAPO-31分子筛之间发生转晶现象。 相似文献
6.
7.
8.
改变硅源和晶化时间合成了系列SAPO-5分子筛,用原位红外光谱和NH3-TPD研究了不同样品的酸碱性,用TG-DTA和MAS NMR考察了硅源及晶化时间对分子筛模板剂的影响,评价了不同样品对正己烷裂解的催化活性。结果表明,SAPO-5分子筛孔道不仅与模板剂的胺基有作用,而且与其甲基也有作用。以硅凝胶为硅源时,在48h内,延长晶化时间可使分子筛中硅含量和强酸中心数目增加,低温下正己烷裂解活性提高;晶 相似文献
9.
10.
11.
《Comptes Rendus Chimie》2015,18(9):929-934
The compound bis(ethylenediamine-N,N′)-(oxalato-O,O′)-cobalt biphenyl-4,4′-disulfonate hydrate, refcode TIQHOR, crystallizes with four Co(III) cations in the asymmetric unit. Another pair of compounds, rac-bis(ethylenediamine-N,N′)-(oxalato-O,O′)-cobalt(III) l-hydrogenaspartate, refcode VAGBOU, and tetra-ammine-(N-benzylethanediamine)-cobalt(III) trinitrate sesquihydrate, refcode ZIFHEB crystallize both as conglomerates and kryptoracemates. Their stereochemical characteristics are described, and the fact that they display more than one mode of crystallization in a single lattice, is illustrated numerically and visually. 相似文献
12.
Transient and athermal effects in the crystallization of polymers. II. Nonisothermal crystallization
Pawe Sajkiewicz 《Journal of Polymer Science.Polymer Physics》2003,41(1):68-79
Nonisothermal crystallization of several polymers was investigated with differential scanning calorimetry and optical microscopy. The results indicated that as in the case of isothermal processes, crystallization starts with nucleation on noncompletely melted crystalline residues. It is assumed that if the crystalline residues are subcritical at melting temperatures, they can become stable by an athermal mechanism during cooling. There is also some contribution of nucleation on heterogeneities. The next mechanism of nucleation is a classical homogeneous process occurring by thermal fluctuations. The results showed the non‐steady‐state character of the nonisothermal crystallization of polymers. In the investigated range of cooling rates, the non‐steady‐state character of nonisothermal crystallization of polymers is dominated by the transient thermal effects. In the range of high temperatures, the transient homogeneous nucleation can be interpreted with the Ziabicki model, and the steady‐state rate determined from nonisothermal experiments coincides with the rate determined in isothermal crystallization. The athermal nucleation occurring at the beginning of crystallization from noncompletely melted aggregates seems to be independent of the applied cooling rate. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 68–79, 2003 相似文献
13.
Thedevelopmentofmetallocenecatalystsundoubtedlyrepresentsarevolutioninthepolyolefinbusiness.MetallocenePE(MPE)coverspolyethyleneswhichareproducedbymetallocenecatalysttechnology.EXXONChemicalCo.developedanewmeta-llocenepolyethylene-EXCEED'"PEin1991.Nowmoreandmoreeffortsarespentonthisinterestingproject.Uniformmolecularstructureandnarrowmoleculardistribution,makeMPEbetterphysicalpropertiesthanthoseofconventionalPE,andalsomakeitlowmeltstrengthandbadprocessability.Sotherelationshipbetween… 相似文献
14.
Păcurariu C. Lazău R. I. Lazău I. Stoleriu Ş. 《Journal of Thermal Analysis and Calorimetry》2007,88(3):641-645
A kinetic study of the crystallization processes was performed for some decorative ceramic glazes in the PbO-SiO2-Na2O-K2O-CaO(BaO)-Al2O3-B2O3 system with addition of 10% TiO2 and ZnO. The crystallization kinetics has been studied in non-isothermal conditions using DTA technique. The apparent activation
energies of the crystallization processes were calculated using the Kissinger method. The main crystalline phase, which provides
the decorative effect, is rutile. This has been identified by X-ray diffraction and it is clearly visible in the optical microscopy
images taken in transmitted light, as needle-like or even prismatic crystals arranged in radial-fibrous aggregates. 相似文献
15.
16.
The crystallization kinetics of Cu55Zr45 (at%) glassy alloy is studied under isothermal condition using differential scanning calorimetry (DSC). The plot of correlation between the crystallized volume fraction α and annealing time t shows a sigmoid-type curve, which is steeper with higher annealing temperature. Furthermore, in isothermal crystallization condition, local activation energy Eα values, determined using the Arrhenius equation, range from 181.1 to 187.8 kJ/mol, which is nearly a constant. The local Avrami exponent n(α) values, obtained by the Johnson-Mehl-Avrami equation, which range from 2.2 to 4.0 at different annealing temeperatures, which indicates that the crystallization mechanism is diffusion-controlled transformation. Moreover, n(α) becomes greater with increasing annealing temperature, which indicates that annealing temperature can affect nucleation rate and growth type. 相似文献
17.
The intention of this work presented is to introduce new processing principles for the crystallization of watery or fatty phases in food systems, and in particular to quantify the process — microstructure — product quality relationships for such food systems. The crystallization processes demonstrated in detail are high shear crystallization (i), spray crystallization (ii) and spray powder based seed crystallization (iii). Crystalline, semi-crystalline and/or amorphous structures were analysed by calorimetric, mechanical/rheological and microscopical methods. Quality aspects of the final food products, which are related to the structure of the crystalline and/or amorphous components, were investigated additionally.This revised version was published online in November 2005 with corrections to the Cover Date. 相似文献
18.
Poly(3,3-dimethyl oxetane) fractions ranging in number average molecular weights from 18500 to 130000 have been isothermally crystallized from the relaxed melt state in the temperature range from 12 to 44 °C, where only the monoclinic modification is formed. The influence of molecular weight and undercooling in crystallization kinetics has been analyzed. The level of crystallinity is very slightly dependent on molecular weight but the influence of this parameter on the time scale of the crystallization is relatively pronounced. The crystallization temperature coefficient was determined and it was found a constant value of the product of the interfacial energies in the range of molecular weights which has been analyzed. Growth rate measurements were carried out for fraction ¯M
n=130000 and it was found that the temperature coefficients for overall and growth rates are equal. Finally, the comparison of the experimental results for this polymer with those reported for poly(oxetane) shows two main differences: first, the crystallization rate is slower for poly(3,3-dimethyl oxetane) and second, the temperature coefficient is smaller for this polymer. 相似文献
19.
The enthalpies of crystallization of NaCl, KCl, LiCl·H2O, MgCl2·6H2O, CaCl2·6H2O and BaCl2·2H2O from aqueous solution were determined by means of different calculation methods on the basis of the earlier-measured differential and integral enthalpies of solution of the above salts. The obtained crystallization enthalpies are discussed and compared with the appropriate literature data.
Zusammenfassung Es wurden die Kristallisationenthalpien des NaCl, KCl, LiCl·H2O, MgCl2·6H2O, CaCl2·6H2O und BaCl2·2H2O aus wässerigen Lösungen bestirnt. Es wurden vorher gemessene differenzierte und integrale Enthalpien von oben genannten gelösten Salze ausgenutzt, bei denen verschiedene Berechnungsmethoden angewandt wurden. Die gewonenen Kristallisationenthalpien wurden mit entsprechenden Literaturangaben erörtert und vergliechen.相似文献
20.
天然橡胶特有的应变诱导结晶能力赋予其优异的力学性能.异戊橡胶作为唯一能够替代天然橡胶的合成橡胶品种,其应变诱导结晶能力受到关注.本文对3种异戊橡胶的微观序列结构进行了分析,并研究了其结晶性能.核磁分析结果表明:3种异戊橡胶的顺-1,4-结构含量差别不大;从1,4-结构单元的键接方式(序列结构)看,SKI-5和YS-IR分子链中顺-1,4-结构单元均以头-尾相接的方式沿分子链排列,不存在头-头键和尾-尾键接方式;SKI-3中约有0.4%~0.5%的1,4-单元采取头-头键接方式,约有0.3%~0.6%的1,4-单元采取尾-尾键接方式;根据定量计算结果,从分子链上1,4-结构单元的序列分布来看,SKI-3的规整性与SKI-5、YS-IR相近或略高.XRD研究结果表明:炭黑填充的天然橡胶硫化胶拉伸至400%以上时发生取向结晶;而炭黑填充的异戊橡胶硫化胶需拉伸至500%以上时才发生取向结晶.基本物理机械性能研究表明:3种异戊橡胶的性能相当,拉伸强度和撕裂强度明显低于天然橡胶;由于结构和组成上的差异,异戊橡胶的结晶能力较天然橡胶差. 相似文献