Effect of additives on the photovoltaic properties of organic solar cells based on triphenylamine-containing amorphous molecules

Photovoltaic performance of the organic solar cells(OSCs)based on 2-((5′-(4-((4-((E)-2-(5′-(2,2-dicyanovinyl)-3′,4-dihexyl-2,2′-bithiophen-5-yl)vinyl)phenyl)(phenyl)amino)styryl)-4,4′-dihexyl-2,2′-bithiophen-5-yl)methylene)malononitrile(L(TPAbTV-DCN))as donor and PC70BM as acceptor was optimized using 0.25 vol%high boiling point solvent additive of1-chloronaphthalene(CN),1,6-hexanedithiol(HDT),or 1,8-diodooctane(DIO).The optimized OSC based on L(TPA-bTVDCN)–PC70BM(1:2,w/w)with 0.25 vol%CN exhibits an enhanced power conversion efficiency(PCE)of 2.61%,with Voc of0.87 V,Jsc of 6.95 mA/cm2,and FF of 43.2%,under the illumination of 100 mW/cm2 AM 1.5 G simulated solar light,whereas the PCE of the OSC based on the same active layer without additive is only 1.79%.The effect of the additive on absorption spectra and the atomic force microscopy images of L(TPA-bTV-DCN)–PC70BM blend films were further investigated.The improved efficiency of the device could be ascribed to the enhanced absorption and optimized domain size in the L(TPA-bTV-DCN)–PC70BM blend film.     

Synthesis, characterization and solar cell application of a D-A copolymer with cyclopentadithiophene and fluorene as donor units

In this paper, a new D-A copolymer, PFDBCPDT, which consists of benzo-2,1,3-thiadiazole as acceptor units and cyclopentadithiophene and fluorene as donor units, was synthesized. The thermal, electrochemical, photophysical and photovoltaic properties of PFDBCPDT were studied. PFDBCPDT showed a low optical band gap of 1.84 eV, and relatively low HOMO level of ?5.69 eV. The best device performance was obtained by PFDBCPDT/PC₆₁BM (1:3) with 0.5 vol% DIO. The device exhibited a power conversion efficiency of 3.06%, with a relatively high open circuit voltage of 0.87 eV.     

Synthesis of D-A copolymers based on thiadiazole and thiazolothiazole acceptor units and their applications in ternary polymer solar cells

We have designed and synthesized two wide bandgap new donor-acceptor (D-A) copolymers consisting of the same alkylthiazole-substituted benzo[1,2-b;4,5-b′]dithiophene (BDTTz) donor unit and but different acceptor units, i.e., thiazolo[5,4-d]thiazole (TT_Z) ( P122 ) and 1,3,-4 thiadiazole (TDz) ( P123 ) and investigated their optical and electrochemical properties. We have employed these copolymers as donor and fullerene (PC ₇₁ BM) and narrow bandgap non-fullerene (Y6) as acceptor, to fabricate binary and ternary bulk heterojunction polymer solar cells (PSCs). The overall power conversion efficiency (PCE) of optimized binary bulk heterojunction PSCs based on P122 :Y6 and P123 :Y6 is 12.60% and 13.16%, respectively. The higher PCE for PSCs based on P123 than P122 counterparts may be associated with the broader absorption profile of the P123 and more charge carrier mobilities than that for the P122 active layer. With the incorporation of small amount of PC₇₁BM into either P122 :Y6 or P123 :Y6 binary blend, the corresponding ternary PSCs showed an overall PCE of 14.89% and 15.52%, respectively, which is higher than the binary counterparts using either Y6 or PC₇₁BM as acceptor. Incorporating the PC₇₁BM in the binary host blend increases the absorption in the 300–500 nm wavelength region, generating more excitons in the active ternary layer and helping to dissociate the excitons into free charge carriers more effectively. The more appropriate nanoscale phase separation in the active ternary layer than the binary counterpart may be one of the reasons for higher PCE.     

通过调节共轭聚合物侧链实现可绿色溶剂加工的非富勒烯太阳能电池

有机太阳能电池(OSC)经过长期的发展,其能量转换效率(PCE)已快速推进至14%–16%,基本接近可商业化应用的范围,但在目前所见报道的高效率OSC器件的制备过程中,活性层薄膜的加工大多采用氯苯、二氯苯、氯仿等毒性较高的含卤/芳香性试剂,此类试剂对环境及人类健康的危害非常高。在本工作中,我们基于已报道的高效率给体共轭聚合物PBDB-T,通过扩大共轭侧链结构与增长柔性烷基侧链的方式,合成了新型给体聚合物PBDB-DT。PBDB-DT中较长的柔性烷基侧链保证了其在低毒性溶剂四氢呋喃(THF)溶液中良好的溶解度,同时,扩大的共轭侧链也有效增强了其在THF中的溶液聚集作用,这一特性对于在非富勒烯型OSC器件中获得较好的光伏性能尤其重要。当采用非富勒烯小分子IT-M作为电子受体材料时,以THF为主溶剂加工的基于PBDB-DT:IT-M的OSC器件可以获得10.2%的能量转换效率。     

Ternary solvent-processed efficient organic solar cells based on a new A-DA'D-A acceptor derivative employing the 3rd-position branching side chains on pyrroles

Recent advances in non-fullerene acceptors(NFAs),typically Y6,have driven power conversion efficiency(PCE) of single-junction orga nic solar cells(OSCs) over 16%.Mea nwhile,it becomes essential to know how to adopt simple strategies to further improve device performance.In this work,a new A-DA'D-A acceptor derivative,Y19-N3 employing 3-ethylheptyl branched at the 3^rd-position instead of 2-ethylhexyl on the pyrroles of Y19 is reported.The selection of an appropriate solvent in casting device is implemented to maximize the photovoltaic performance.PBDB-T:Y19-N3-based OSCs treated with a ternary solvent of CF/CB(1:3,v/v) and 0.8% DIO exhibit the optimal PCE of 13.77% here,with the significantly improved V_oc(0.78 V) and FF(0.72) as well as the high J_sc(24.46 mA/cm²).Further characterizations indicate that this ternary solvent-treated PBDB-T/Y19-N3 film exhibits the more appropriate morphological features with the highly efficient charge generation and collection as well as the more balanced electron and hole mobilities.This work combines molecular design and device engineering to improve the photovoltaic properties,which is important to the development of OSCs.     

Synthesis and investigation of photovoltaic properties for polymer semiconductors based on porphyrin compounds as light-harvesting units

We reported on two polymer semiconducting copolymers based on porphyrin compounds, poly[9,9-dioctylfluorene-co-5,15-bis(hexoxybenzyl)-10,20-bis(benzo-4-yl)porphyrin] (PFPor) and poly[9-(heptadecan-9-yl)carbazole-co-5,15-bis(hexoxybenzyl)-10,20-bis(benzo-4-yl)porphyrin] (PCPor), for use as organic photovoltaic materials. The thermal, optical, electrochemical, and photovoltaic properties of the two polymers were investigated. In addition, PC₆₁BM and PC₇₁BM were introduced as acceptor materials to confirm the acceptor effect in bulk heterojunction photovoltaic devices. Moreover, in order to establish acceptor effects, morphologies of polymer/PCBM blend films were analyzed through atomic force microscopy (AFM). PFPor and PCPor exhibited the best device performance with power conversion efficiencies (PCE) of 0.62% and 0.76%, respectively, upon the introduction of PC₇₁BM as the acceptor in the device where 86 wt.% of the PC₇₁BM was contained in the active layer (pol:PC₇₁BM = 1:6, w/w).     

Impact of symmetry-breaking of non-fullerene acceptors for efficient and stable organic solar cells

The concurrent enhancement of short-circuit current (J_SC) and open-circuit voltage (V_OC) is a key problem in the preparation of efficient organic solar cells (OSCs). In this paper, we report efficient and stable OSCs based on an asymmetric non-fullerene acceptor (NFA) IPC-BEH-IC2F. The NFA consists of a weak electron-donor core dithienothiophen[3,2-b]-pyrrolobenzothiadiazole (BEH) and two kinds of strong electron-acceptor (A) units [9H-indeno[1,2-b]pyrazine-2,3-dicarbonitrile (IPC) with a tricyclic fused system and 2-(5,6-difluoro-3-oxo-2,3-dihydro-1H-inden-1-ylidene)malononitrile (IC2F)]. For comparison, the symmetric NFAs IPC-BEH-IPC and IC2F-BEH-IC2F were characterised. The kind of flanking A unit significantly affects the light absorption features and electronic structures of the NFAs. The asymmetric IPC-BEH-IC2F has the highest extinction coefficient among the three NFAs owing to its strong dipole moment and highly crystalline feature. Its highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) levels lie between those of the IPC-BEH-IPC and IC2F-BEH-IC2F molecules. The IPC group also promotes molecular packing through the tricyclic π-conjugated system and achieves increased crystallinity compared to that of the IC2F group. Inverted-type photovoltaic devices based on p-type polymer:NFA blends with PBDB-T and PM6 polymers as p-type polymers were fabricated. Among all these devices, the PBDB-T:IPC-BEH-IC2F blend device displayed the best photovoltaic properties because the IPC unit provides balanced electronic and morphological characteristics. More importantly, the PBDB-T:IPC-BEH-IC2F-based device exhibited the best long-term stability owing to the strongly interacting IPC moiety and the densely packed PBDB-T:IPC-BEH-IC2F film. These results demonstrate that asymmetric structural modifications of NFAs are an effective way for simultaneously improving the photovoltaic performance and stability of OSCs.

A 9H-indeno[1,2-b]pyrazine-2,3-dicarbonitrile (IPC) moiety in asymmetric non-fullerene acceptors promotes the formation of a densely packed crystalline structure, enabling efficient and long-term stable organic solar cells.     

Effects of spin-coating speed on the morphology and photovoltaic performance of the diketopyrrolopyrrole-based terpolymer

Polymer solar cells（PSCs） were fabricated by combining a diketopyrrolopyrrole-based terpolymer（PTBT-HTID-DPP） as the electron donor, and [6,6]-phenyl C₆₁ butyric acid methyl ester(PC₆₁BM) as the electron acceptor, and the power conversion efficiency（PCE） of 4.31% has been achieved under AM 1.5 G(100 m W cm^-2) illumination condition via optimizing the polymer/PC₆₁BM ratio, the variety of solvent and the spin-coating speed. The impact of the spin-coating speed on the photovoltaic performance of the PSCs has been investigated by revealing the effects of the spin-coating speed on the morphology and the absorption spectra of the polymer/PC₆₁BM blend films. When the thickness of the blend films are adjusted by spin-coating a fixed concentration with different spin-coating speeds, the blend film prepared at a lower spin-coating speed shows a stronger absorption per unit thickness, and the correspond device shows higher IPCE value in the longer-wavelength region. Under the conditions of similar thickness, the blend film prepared at a lower spin-coating speed forms a more uniform microphase separation and smaller domain size which leads to a higher absorption intensity per unit thickness of the blend film in long wavenumber band, a larger short-circuit current density(J_sc) and a higher power conversion efficiency（PCE） of the PSC device. Noteworthily, it was found that spin-coating speed is not only a way to control the thickness of active layer but also an influencing factor on morphology and photovoltaic performance for the diketopyrrolopyrrole-based terpolymer.     

Enhanced efficiency of ternary organic solar cells by doping a polymer material in P3HT:PC61BM

Doping a low‐bandgap polymer material (PDTBDT‐DTNT) as a complementary electron donor in poly(3‐hexylthiophene) (P3HT) and [6,6]‐phenyl‐C₆₁‐butyricacid methyl ester (PC₆₁BM) blend is experimented to improve the power conversion efficiency (PCE) of organic solar cells (OSCs). The PCE of OSCs was increased from 3.19% to 3.75% by doping 10 wt% PDTBDT‐DTNT, which was 17.55% higher than that of the OSCs based on binary blend of P3HT:PC₆₁BM (host cells). The short‐circuit current density (J_sc) was increased to 10.11 mA·cm⁻² compared with the host cells. Although the PCE improvement could partly be attributed to more photon harvest for complementary absorption of 2 donors by doping appropriate PDTBDT‐DTNT, the promotion of charge separation and transport as well as the suppression of charge recombination due to a matrix of cascade energy levels is also important. And the better morphology of the active layer films is beneficial to the optimized performance of ternary devices.     

Effect of side‐chain positions on morphology and photovoltaic properties of phenazine‐based donor–acceptor copolymers

Two phenazine donor–acceptor‐conjugated copolymers (P1 and P2) with the same polymer backbone but different anchoring positions of alkoxy chain on the phenazine unit were investigated to identify the effect of changing the position of alkoxy chains on their optical, electrochemical, blend film morphology, and photovoltaic properties. Although the optical absorption and frontier orbital energy levels were insensitive to the position of alkoxy chains, the film morphologies and photovoltaic performances changed significantly. P1/PC₇₁BM blend film showed the formation of phase separation with large coarse aggregates, whereas P2/PC₇₁BM blend film was homogeneous and smooth. Accordingly, power conversion efficiency (PCE) of photovoltaic devices increased from 1.50% for P1 to 2.54% for P2. In addition, the PCE of the polymer solar cell based on P2/PC₇₁BM blend film could be further improved to 3.49% by using solvent vapor annealing treatment. These results clearly revealed that tuning the side‐chain position could be an effective way to adjust the morphology of the active layer and the efficiency of the photovoltaic device. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2910–2918     

Designing Nonfullerene Acceptors with Oligo(Ethylene Glycol) Side Chains: Unraveling the Origin of Increased Open-Circuit Voltage and Balanced Charge Carrier Mobilities

Despite the recent rapid development of organic solar cells (OSCs), the low dielectric constant (ϵ_r=3–4) of organic semiconducting materials limits their performance lower than inorganic and perovskite solar cells. In this work, we introduce oligo(ethylene glycol) (OEG) side chains into the dicyanodistyrylbenzene-based non-fullerene acceptors (NIDCS) to increase its ϵ_r up to 5.4. In particular, a NIDCS acceptor bearing two triethylene glycol chains (NIDCS-EO3) shows V_OC as high as 1.12 V in an OSC device with a polymer donor PTB7, which is attributed to reduced exciton binding energy of the blend film. Also, the larger size grain formation with well-ordered stacking structure of the NIDCS-EO3 blend film leads to the increased charge mobility and thus to the improved charge mobility balance, resulting in higher J_SC, FF, and PCE in the OSC device compared to those of a device using the hexyl chain-based NIDCS acceptor (NIDCS-HO). Finally, we fabricate NIDCS-EO3 devices with various commercial donors including P3HT, DTS-F, and PCE11 to show higher photovoltaic performance than the NIDCS-HO devices, suggesting versatility of NIDCS-EO3.     

A Polyfluoroalkyl-Containing Non-fullerene Acceptor Enables Self-Stratification in Organic Solar Cells

The elaborate control of the vertical phase distribution within an active layer is critical to ensuring the high performance of organic solar cells (OSCs), but is challenging. Herein, a self-stratification active layer is realised by adding a novel polyfluoroalkyl-containing non-fullerene small-molecule acceptor (NFSMA), EH-C₈F₁₇, as the guest into PM6:BTP-eC9 blend. A favourable vertical morphology was obtained with an upper acceptor-enriched thin layer and a lower undisturbed bulk heterojunction layer. Consequently, a power conversion efficiency of 18.03 % was achieved, higher than the efficiency of 17.40 % for the device without EH-C₈F₁₇. Additionally, benefiting from the improved charge transport and collection realised by this self-stratification strategy, the OSC with a thickness of 350 nm had an impressive PCE of 16.89 %. The results of the study indicate that polyfluoroalkyl-containing NFSMA-assisted self-stratification within the active layer is effective for realising an ideal morphology for high-performance OSCs.     

A New D–A conjugated polymer P(PTQD‐BDT) with PTQD acceptor and BDT donor units for BHJ polymer solar cells application

A novel donor–acceptor ( D–A ) copolymer comprising of weak electron donating BDT moiety and strong 9‐(2‐octyldodecyl)?8H‐pyrrolo[3,4‐b] bisthieno[2,3‐f:3',2'‐h] quinoxaline‐8,10(9H)‐dione (PTQD) unit denoted as P(PTQD‐BDT) was synthesized as donor material for polymer solar cells. P(PTQD‐BDT) shows a broad visible‐near‐infrared absorption band with an optical bandgap of 1.74 eV and possesses a relatively low‐lying HOMO level at ?5.28 eV. Bulk‐heterojunction polymer solar cell with the optimized blend of 1:2 (weight ratio) P(PTQD‐BDT):PC₇₁BM (processed with chloroform) shows an open circuit voltage of 0.92 V, a short circuit current density of 7.84 mA/cm², and a fill factor of 0.50, achieving a power conversion efficiency (PCE) of 3.61%. The PCE has been further improved to 5.55 % (J_sc = 10.34 mA/cm², V_oc = 0.88V and FF = 0.61), when 3% v ol 1,8‐diio‐dooctane (DIO) was used as solvent additive for the processing of P(PTQD‐BDT):PC₇₁BM blended film. The enhancement in J_sc is as a result of the appropriate morphology and efficient exciton dissociation into free charge carrier. The increase in PCE has been attributed to the favorable nanoscale morphology for efficient exciton dissociation and charge transport (reduction in the electron to hole mobility ratio). © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2390–2398     

Synergistic effect of fluorination on both donor and acceptor materials for high performance non-fullerene polymer solar cells with 13.5% efficiency

A high performance polymer solar cells(PSCs) based on polymer donor PM6 containing fluorinated thienyl benzodithiophene unit and n-type organic semiconductor acceptor IT-4 F containing fluorinated end-groups were developed. In addition to complementary absorption spectra(300–830 nm) with IT-4 F, the PM6 also has a deep HOMO(the highest occupied molecular) level(-5.50 e V), which will lower the open-circuit voltage(V_(oc)) sacrifice and reduce the E_(loss) of the IT-4 F-based PSCs. Moreover, the strong crystallinity of PM6 is beneficial to form favorable blend morphology and hence to suppress recombination. As a result, in comparison with the PSCs based on a non-fluorinated D/A pair of PBDB-T:ITIC with a medium PCE of 11.2%, the PM6:IT-4 Fbased PSCs yielded an impressive PCE of 13.5% due to the synergistic effect of fluorination on both donor and acceptor, which is among the highest values recorded in the literatures for PSCs to date. Furthermore, a PCE of 12.2% was remained with the active layer thickness of up to 285 nm and a high PCE of 11.4% was also obtained with a large device area of 1 cm~2. In addition, the devices also showed good storage, thermal and illumination stabilities with respect to the efficiency. These results indicate that fluorination is an effective strategy to improve the photovoltaic performance of materials, as well as the both fluorinated donor and acceptor pair-PM6:IT-4 F is an ideal candidate for the large scale roll-to-roll production of efficient PSCs in the future.     

An Oligothiophene–Fullerene Molecule with a Balanced Donor–Acceptor Backbone for High‐Performance Single‐Component Organic Solar Cells

A new balanced donor–acceptor molecule, namely, benzodithiophene (BDT)‐rhodanine‐[6,6]‐phenyl‐C₇₁ butyric acid methyl ester (Rh‐PC₇₁BM) comprising two covalently linked blocks, a p‐type oligothiophene‐containing BDT‐based moiety and an n‐type PC₇₁BM unit was designed and synthesized. The single‐component organic solar cell (SCOSC) fabricated from Rh‐PC₇₁BM molecules showed a power conversion efficiency (PCE) of 3.22 % with an open‐circuit voltage (V_oc) of 0.98 V. These results rank are among the highest values for SCOSCs based on a monomolecular material. In particular, the one‐molecule Rh‐PC₇₁BM device exhibits excellent thermal stability compared to reference Rh‐OH:PC₇₁BM device. The success of our monomolecular strategy can provide a new way to develop high‐performance SCOSCs.     

Facile,Versatile and Stepwise Synthesis of High-Performance Oligomer Acceptors for Stable Organic Solar Cells

Oligomer acceptors have recently emerged as promising photovoltaic materials for achieving high power conversion efficiency (PCE) and long-term stability in organic solar cells (OSCs). However, the limited availability of diverse acceptors, resulting from the sole synthetic approach, has hindered their potential for future industrialization. In this study, we present a facile and effective stepwise approach that utilizes two consecutive Stille coupling reactions for the synthesis of oligomer acceptors. To demonstrate the feasibility of the novel approach, we successfully synthesize a trimer acceptor, Tri-Y6-OD, and further systematically investigate the impact of oligomerization on device performance and stability. The results reveal that this approach has significant advantages compared to the conventional method, including reduced formation of unwanted by-products and lower difficulties in purification. Remarkably, the OSC based on PM6 : Tri-Y6-OD achieves an impressive PCE of 18.03 % and maintains 80 % of the initial PCE (T₈₀) for 1523 h under illumination, surpassing the performance of the corresponding small molecule acceptor Y6-OD-based device. Furthermore, the versatility of the synthetic strategy in obtaining diverse acceptors is further demonstrated. Overall, our findings provide a facile, versatile and stepwise way for synthesizing oligomer acceptors, thereby facilitating the development of stable and efficient OSCs.     

Effects of processing additives in non-fullerene organic bulk heterojunction solar cells with efficiency >11%

The solar cell surface morphologies with different additives observed with slightly changed in roughness. It is easily to get the best PCE of 11.1% with using 0.5% DIO additives.     

Enhancement the photovoltaic performance of conjugated polymer based on simple head-to-head alkylthio side chains engineered bithiophene

In this article, three novel and simple molecular structure with donor-acceptor (D-A) type copolymers via only head-to-head alkoxy (OR) and/or alkylthio (SR) side chains onto the bithiophene (BT) as donor units and fluorinated benzotriazole (FBTA) as acceptor unit, namely, PBTOR-FBTA, PBTOSR-FBTA and PBTSR-FBTA, were successfully designed and synthesized. The impacts of sulfur-oxygen (S⋯O) or sulfur-sulfur (S⋯S) noncovalent interactions on their physicochemical properties, molecular stacking, carrier mobility, morphologies of blend films, as well as their photovoltaic performance were deeply and systematically studied. The introduction of SR side-chains suddenly lowered the highest occupied molecular orbital (HOMO) energy levels, blue-shifted absorption, enhanced π-π stacking, as well as improved morphology of the photoactive layer blends in comparison with the reference polymer without SR side-chain. Polymer solar cells (PSCs) were fabricated to estimate their photovoltaic performance of the polymers. Under an optimized blend ratio of PBTSR-FBTA:PC₇₁BM (1:0.8, w/w), the PBTSR-FBTA-based device exhibits a higher power conversion efficiency (PCE) of 6.25%, which is about 3.34 and 1.87 folds than that of the PBTOR-FBTA and PBTOSR-FBTA-based devices, respectively. Our research results demonstrate that the modification of the simple and low-cost SR side chains is an effective strategy to improve the photovoltaic performance of the polymers.     

High-Performance All-Polymer Solar Cells: Synthesis of Polymer Acceptor by a Random Ternary Copolymerization Strategy

Demonstrated in this work is a simple random ternary copolymerization strategy to synthesize a series of polymer acceptors, PTPBT-ET_x, by polymerizing a small-molecule acceptor unit modified from Y6 with a thiophene connecting unit and a controlled amount of an 3-ethylesterthiophene (ET) unit. Compared to PTPBT of only Y6-like units and thiophene units, PTPBT-ET_x (where x represents the molar ratio of the ET unit) with an incorporated ET unit in the ternary copolymers show up-shifted LUMO energy levels, increased electron mobilities, and improved blend morphologies in the blend film with the polymer donor PBDB-T. And the all-polymer solar cell (all-PSC) based on PBDB-T:PTPBT-ET_0.3 achieved a high power conversion efficiency over 12.5 %. In addition, the PTPBT-ET_0.3-based all-PSC also exhibits long-term photostability over 300 hours.     

A New Small-Molecule Donor Containing Non-Fused Ring π-Bridge Enables Efficient Organic Solar Cells with High Open Circuit Voltage and Low Acceptor Content

To achieve high open-circuit voltage (V_oc) and low acceptor content, the molecular design of a small-molecule donor with low energy loss (E_loss) is very important for solution-processable organic solar cells (OSCs). Herein, we designed and synthesized a new coplanar A−D−A structured organic small-molecule semiconductor with non-fused ring structure π-bridge, namely B2TPR , and applied it as donor material in OSCs. Owing to the strong electron-withdrawing effect of the end group and the coplanar π-bridge, B2TPR exhibits a low-lying highest occupied molecular orbital and strong crystallinity. Furthermore, benefiting from the coplanar molecular skeleton, the high hole mobility, balanced charge transport and reduced recombination were achieved, leading to a high fill factor (FF). The OSCs based on B2TPR : PC₇₁BM blend film (w/w=1 : 0.35) demonstrates a moderate power conversion efficiency (PCE) of 7.10 % with a remarkable V_oc of 0.98 V and FF of 64 %, corresponding to a low fullerene content of 25.9 % and a low E_loss of 0.70 eV. These results demonstrate the great potential of small-molecule with structure of B2TPR for future low-cost organic photovoltaic applications.