Facile synthesized Cu-SnO2 anode materials with three-dimensional metal cluster conducting architecture for high performance lithium-ion batteries

A novel Cu-SnO₂ anode material derived from Cu₆Sn₅ alloy, retaining high conductivity of Cu and high theoretical capacity of SnO₂ with a facile synthesizing process by oxidation and reduction method. The novel Cu structure penetrates in the composite particles inducing high conductivity and spaceconfined SnO₂, which restrict the pulverization of SnO₂ during lithiation/delithiation process.     

Synthesis and properties of novel heat-resistant fluorescent conjugated polymers with bisindolylmaleimide

Novel conjugated polymers with bisindolymaleimide were synthesized via simple metal-free condensation polymerization. The polymers exhibited high glass transition temperatures and decomposition temperatures with considerable luminescent properties.     

Cobalt-free cathode material SrFe0.9Nb0.1O3−δ for intermediate-temperature solid oxide fuel cells

A cobalt-free cubic perovskite oxide, SrFe_0.9Nb_0.1O_3?δ (SFN) was investigated as a cathode for intermediate-temperature solid oxide fuel cells (IT-SOFCs). XRD results showed that SFN cathode was chemically compatible with the electrolyte Sm_0.2Ce_0.8O_1.9 (SDC) for temperatures up to 1050 °C. The electrical conductivity of SFN sample reached 34–70 S cm^?1 in the commonly operated temperatures of IT-SOFCs (600–800 °C). The area specific resistance was 0.138 Ω cm² for SFN cathode on SDC electrolyte at 750 °C. A maximum power density of 407 mW cm^?2 was obtained at 800 °C for single-cell with 300 μm thick SDC electrolyte and SFN cathode.     

Effects of calcination and activation temperature on dry reforming catalysts

The effect of calcination temperatures on dry reforming catalysts supported on high surface area alumina Ni/γ-Al₂O₃ (SA-6175) was studied experimentally. In this study, the prepared catalyst was tested in a micro tubular reactor using temperature ranges of 500, 600, 700 and 800 °C at atmospheric pressure, using a total flow rate of 33 ml/min consisting of 3 ml/min of N₂, 15 ml/min of CO₂ and 15 ml/min of CH₄. The calcination was carried out in the range of 500–900 °C. The catalyst is activated inside the reactor at 500–800 °C using hydrogen gas. It was observed that calcination enhances catalyst activity which increases as calcination and reaction temperatures were increased. The highest conversion was obtained at 800 °C reaction temperature by using catalyst calcined at 900 °C and activation at 700 °C. The catalyst characterization conducted supported the observed experimental results.     

Quantitative and kinetic TG-FTIR study of biomass residue pyrolysis: Dry distiller's grains with solubles (DDGS) and chicken manure

New energy policies all over the world are trying to tackle high oil prices and climate change by promoting the use of biomass to produce heat, electricity and liquid transportation fuels. In this paper we studied two different secondary fuels: dry distiller's grains with solubles (DDGS) and chicken manure. These materials have high content of nitrogen and ashes which limit their usage in thermal applications due to potential excessive NO_x emissions and problems of slagging, fouling, corrosion and loss of fluidization.The fuels tested here were received from industrial partners. In order to reduce the ash content the fuels were pre-treated using water leaching pre-treatment.Pyrolysis of these fuels has been monitored through a TG-FTIR set-up. Quantification of the following volatile species was possible: CO, CO₂, CH₄, HCN, NH₃, HNCO, H₂O.The water leaching appeared to decrease the amount of ashes in both samples and remove some of the troublesome compounds like Cl, S and K.The DDGS thermogravimetric curve showed three main peaks at 280 °C, 330 °C and 402 °C with a total weight loss of around 79%wt_a.r. (on an “as received” basis). NH₃ is the main N-compound released at low temperatures with a peak at 319 °C. HNCO and HCN were detected at higher temperatures of around 400 °C. Chicken manure reacted in four stages with peaks at 280 °C, 324 °C, 430 °C and 472 °C with a total average weight loss of 66%wt_a.r. The main N-compound was HNCO, released at 430 °C. Ammonia was detected during the whole measurement, while HCN presented peaks of reactivity at 430 °C and 472 °C.Kinetic analysis was applied using a distributed activation energy method (DAEM) using discrete and Gaussian distributions and data for further modeling purposes were retrieved and presented.     

Polyimide-derived carbon nanofiber membranes as anodes for high-performance flexible lithium ion batteries

Heteroatoms-doped carbon nanofiber membranes with flexible features were prepared by electrospinning with heterocyclic polyimide (PI) structures containing biphenyl and pyrimidine rings. The products with optimized treatment could achieve 695 mAh/g at 0.1 A/g and retain 245 mAh/g at 1.5 A/g after 300 cycles when used as anode for Li-ion batteries.     

Synthesis,spectroscopic, structural and thermal characterizations of [(C7H6NO4)2TeBr6·4H2O]

Tellurium (IV) complexes with pyridine-2,6-dicarboxylate ligand were synthesized by slow evaporation from aqueous solutions yielding a new compound: [(C₇H₆NO₄)₂TeBr₆·4H₂O]. The structure of this compound was solved and refined by single-crystal X-ray diffraction. The compound is centrosymmetric P2₁/c (N°: 14) with the parameters a = 8.875(5) Å, b = 15.174(5) Å, c = 10.199(5) Å, β = 94.271° (5) and Z = 2. The structure consists of isolated H₂O, isolated [TeBr₆]^2? octahedral anions and (pyridine-2,6-dicarboxylate) [C₇H₆NO₄]⁺ cations. The stability of the structure was ensured by ionic and hydrogen bonding contacts (N–H?Br and O–H?Br) and Van-Der Walls interaction. The thermal decomposition of the compound was studied by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The FTIR and Raman spectroscopy at different temperatures confirm the existence of vibrational modes that correspond to the organic, inorganic and water molecular groups. Additionally, the UV–Vis diffuse reflectance spectrum was recorded in order to investigate the band gap nature. The measurements show that this compound exhibits a semiconducting behavior with an optical band gap of 2.66 eV.     

Smart synthesis of silver nanoparticles supported in porous polybenzoxazine nanocomposites via a main-chain type benzoxazine resin

Novel silver nanoparticles immobilized on macroporous polybenzoxazine nanocomposites were prepared as catalysts for catalytic reduction reaction.     

Synthesis and characterization of porous WO3–SnO2 nanomaterials: An infrared study of adsorbed pyridine and dimethyl methylphosphonate

High surface area porous W/Sn oxide nanomaterials were prepared via water/oil based (W/O) emulsion. Tungstic acid solution was generated by cation exchange of sodium tungstate in acidic Dowex resin. The acid was then mixed with a clear homogeneous aqueous N-cetyl trimethyl ammonium bromide (CTAB) solution followed by a slow addition of 0.2 M SnCl₄ solution. The mixture was stirred for 24 h and then subjected to slow calcination at 500 °C. The prepared materials were characterized using SEM-EDX, BET surface area, and sorption of nitrogen and water. Fourier transform infrared spectroscopy (FTIR) was used to characterize the surface acidic properties using pyridine vapor as a probe. The materials were then tested toward the Dimethyl methylphosphonate (DMMP) adsorption at various temperatures using infrared spectroscopy. At elevated temperatures, the desorption of DMMP from WO₃ and SnO₂ surfaces results in forming methyl phosphonate that strongly bounds on the metal oxide surfaces. In contrast, the FTIR spectra showed that the adsorbed dimethyl methylphosphonate (DMMP) on the mixed W/Sn oxide powders can be molecularly desorbed without any decomposition.     

Bismuth oxide nanoflake@carbon film: A free-standing battery-type electrode for aqueous sodium ion hybrid supercapacitors

An efficient strategy is developed to fabricate binder-free Bi₂O₃@C nanoflake film anode, which is utilized to assemble a high-performance aqueous sodium ion hybrid supercapacitor.     

Thermal racemization of biaryl atropisomers

Many biaryl compounds possess atropisomerism due to the steric hindrance of substituents at the ortho-position of the two aromatic moieties. Upon heating, atropisomers may have enough energy to surpass the rotational energy barrier and racemize. The thermal stability of five atropisomers was studied using chiral chromatography by following the change in enantiomeric excess ratio at different temperatures. The first order racemization reaction rate was obtained at a given temperature as the slope of the change in enantiomeric excess ratio versus time. For each atropisomer, the racemization rates at different temperatures led to the value of the rotational energy barrier for racemization, ΔG³, and to the racemization half lifetime, t_1/2, indicating the atropisomer thermal stability. Binaphthol started to racemize significantly at temperature of 190 °C and above while binaphthyldiamine was much more stable showing little or very minor racemization up to 210 °C. A chloro-substituted phenylamino-naphthol was very sensitive to thermal racemization starting at a low 40 °C.     

Influence of iron on the synthesis and stability of yttrium silicate apatite

The stability of yttrium silicate apatite has been investigated by studying the influence of iron as a “stabilising cation” and also by using different synthesis routes. The formation of apatite in samples has been followed by X-ray diffraction and by ²⁹Si MAS NMR spectroscopy. The apatite phase appears to be stable at high temperatures (≈1700 °C) especially when heated in a nitrogen atmosphere; it can also occur in a metastable state when heated in air at lower temperatures; ≈1600 °C if prepared from a Y₂O₃SiO₂ mixture or in the range 950 °C <T< 1150 °C if synthesised by the sol–gel process. Longer heat-treatments result in its decomposition into Y₂Si₂O₇ and Y₂SiO₅. Iron appears to have two roles depending on the temperature; it stabilises the apatite phase at high temperatures when produced by the sol–gel route and catalyses the decomposition of sol–gel derived apatite at low temperatures.     

A cobalt-free electrode material La0.5Sr0.5Fe0.8Cu0.2O3 − δ for symmetrical solid oxide fuel cells

Cobalt-free perovskite oxide La_0.5Sr_0.5Fe_0.8Cu_0.2O_3 − δ (LSFC) was applied as both anode and cathode for symmetrical solid oxide fuel cells (SSOFCs). The LSFC shows a reversible transition between a cubic perovskite phase in air and a mixture of SrFeLaO₄, a K₂NiF₄-type layered perovskite oxide, metallic Cu and LaFeO₃ in reducing atmosphere at elevated temperature. The average thermal expansion coefficient of LSFC in air is 17.7 × 10^− 6 K^− 1 at 25 °C to 900 °C. By adopting LSFC as initial electrodes to fabricate electrolyte supported SSOFCs, the cells generate maximum power output of 1054, 795 and 577 mW cm^− 2 with humidified H₂ fuel (~ 3% H₂O) and 895, 721 and 482 mW cm^− 2 with humidified syngas fuel (H₂:CO = 1:1) at 900, 850 and 800 °C, respectively. Moreover, the cell with humidified H₂ fuel demonstrates a reasonable stability at 800 °C under 0.7 V for 100 h.     

Gold & silver nanoparticles supported on manganese oxide: Synthesis,characterization and catalytic studies for selective oxidation of benzyl alcohol

Nano-gold and silver particles supported on manganese oxide were synthesized by the co-precipitation method. The catalytic properties of these materials were investigated for the oxidation of benzyl alcohol using molecular oxygen as a source of oxygen. The catalyst was calcined at 300, 400 and 500 °C. They were characterized by electron microscopy, powder X-ray diffraction (XRD) and surface area. It was observed that the calcination temperature affects the size of the nanoparticle, which plays a significant role in the catalytic process. The catalyst calcined at 400 °C, gave a 100% conversion and >99% selectivity, whereas catalysts calcined at 300 and 500 °C gave a conversion of 69.51% and 19.90% respectively, although the selectivity remains >99%.     

Systematic trends in (0 0 1) surface ab initio calculations of ABO3 perovskites

By means of the hybrid exchange–correlation functionals, as it is implemented in the CRYSTAL computer code, ab initio calculations for main ABO₃ perovskite (0 0 1) surfaces, namely SrTiO₃, BaTiO₃, PbTiO₃, CaTiO₃, SrZrO₃, BaZrO₃, PbZrO₃ and CaZrO₃, were performed. For ABO₃ perovskite (0 0 1) surfaces, with a few exceptions, all atoms of the upper surface layer relax inward, all atoms of the second surface layer relax outward, and all third layer atoms, again, inward. The relaxation of (0 0 1) surface metal atoms for ABO₃ perovskite upper two surface layers for both AO and BO₂-terminations, in most cases, are considerably larger than that of oxygen atoms, what leads to a considerable rumpling of the outermost plane. The ABO₃ perovskite (0 0 1) surface energies always are smaller than the (0 1 1) and especially (1 1 1) surface energies. The ABO₃ perovskite AO and BO₂-terminated (0 0 1) surface band gaps always are reduced with respect to the bulk values. The B–O chemical bond population in ABO₃ perovskite bulk always are smaller than near the (0 0 1) and especially (0 1 1) surfaces.     

Heat capacities,third-law entropies and thermodynamic functions of the negative thermal expansion material Zn2GeO4 from T=(0 to 400) K

The molar heat capacity of Zn₂GeO₄, a material which exhibits negative thermal expansion below ambient temperatures, has been measured in the temperature range 0.5⩽(T/K)⩽400. At T=298.15 K, the standard molar heat capacity is (131.86 ± 0.26) J · K⁻¹ · mol⁻¹. Thermodynamic functions have been generated from smoothed fits of the experimental results. The standard molar entropy at T=298.15 K is (145.12 ± 0.29) J · K⁻¹ · mol⁻¹. The existence of low-energy modes is supported by the excess heat capacity in Zn₂GeO₄ compared to the sums of the constituent binary oxides.     

Sulfonate group modified Ni catalyst for highly efficient liquid-phase selective hydrogenation of bio-derived furfural

A simple and highly efficient Ni catalyst was synthesized and showed excellent catalytic performance for selectively liquid-phase hydrogenation of furfural to furfuryl alcohol or tetrahydrofurfuryl alcohol.     

Enhanced carbon dioxide adsorption performance and kinetic study of K and Al co-doped Li4SiO4

Effective K and Al incorporation in Li₄SiO₄ leads to the broadened adsorption temperature range and enhanced carbon dioxide adsorption performance.     

The electrochemical properties of thermophilic cytochrome P450 CYP119A2 at extremely high temperatures in poly(ethylene oxide)

The electrochemical measurements were carried out by using thermophilic cytochrome P450 CYP119A2 (P450st) modified with poly(ethylene oxide) (PEO) in PEO₂₀₀ as an electrochemical solvent. The PEO modified P450st gave clear reduction–oxidation peaks by cyclic voltammetry in oxygen-free PEO₂₀₀ up to 120 °C. The midpoint potential measured for the P450st was −120 mV vs. [Fe(CN)₆]⁴⁻/[Fe(CN)₆]³⁻ at 120 °C. The peak separation, ΔE, was 16 mV at 100 mV/s. The estimated electron transfer rate of PEO-P450st at 120 °C was 35.1 s⁻¹. The faster electron transfer reaction was achieved at higher temperatures. The electrochemical reduction of dioxygen was observed at 115 °C with the PEO-modified P450st system.     

Syngas production from ethanol dry reforming over Rh/CeO2 catalyst

Carbon dioxide reforming of ethanol over Rh/CeO₂ catalyst was deeply investigated at different reaction temperatures of 450–700 °C and reactant ratios (CO₂/ethanol from 1 to 3) under atmospheric pressure. The obtained results indicated that Rh/CeO₂ catalyst presented a promising activity and stability for syngas production from renewable bio-ethanol instead of conventional methane. Typically, CO₂-rich conditions (CO₂/ethanol = 3) were favorable for reaction process and dynamic coke cleaning, which led to remarkably stable performance over 65 h on stream. The strong redox capacity of CeO₂ support might also accelerate CO₂ activation and prevent the carbon accumulation over the catalyst surface. Additionally, tunable H₂/CO ratios were available by changing the CO₂/ethanol ratios. The results from characterization of samples before and after catalytic tests allowed to establish the relationship between textural properties and catalytic performance.