微纳米钙钛矿型羟基锡酸钙的合成及对环氧树脂的阻燃性能

钙钛矿型羟基锡酸盐是近年来出现的新型高效阻燃消烟剂. 本文采用化学共沉淀法合成了微纳米钙钛矿型羟基锡酸钙[CaSn(OH)₆, CSH], 并利用扫描电子显微镜、 透射电子显微镜、 X射线衍射仪、 红外光谱仪和X射线光电子能谱仪等对其形貌和结构进行表征. 结果表明合成的CaSn(OH)₆为平均粒径500 nm的纯净正六面体, 粒径均一且分散性良好. 将CaSn(OH)₆应用于环氧树脂(EP)复合阻燃体系(CSH/EP), 并分别采用热重分析、 极限氧指数和锥形量热测试表征了其热降解行为和燃烧性能. 采用扫描电子显微镜、 红外光谱、 X射线衍射和拉曼光谱对EP复合材料的阻燃成炭机制进行探索. 结果表明, CaSn(OH)₆能显著提高EP复合材料的高温稳定性、 热释放速率、 热释放量、 烟释放量和极限氧指数数值. 特别是在很低添加量(0.5%, 质量分数)下, 阻燃消烟性能即得到极大提升, 热释放速率、 总放热量和一氧化碳释放量分别降低45.8%, 25.1%和31.3%. 此外, 由于CaSn(OH)₆在EP基体中的良好分散及较强的界面作用, CaSn(OH)₆在提升EP复合材料阻燃消烟性的同时还提升了EP复合材料的力学强度. 本文合成的CaSn(OH)₆可作为一种多功能的高效阻燃、 消烟和增强剂.     

PP/EVA/OMMT纳米复合材料及其阻燃材料的动态燃烧行为

利用锥形量热仪(CONE)在35kW/m2热辐照条件下,并结合极限氧指数(LOI)和UL-94垂直燃烧测试方法对聚丙烯(PP)/乙烯-醋酸乙烯酯共聚物(EVA)/有机蒙脱土(OMMT)纳米复合材料和加入无卤复配阻燃剂制备的PP/EVA/OMMT/氢氧化铝(ATH)/三氧化二锑(AO)纳米复合阻燃材料的热释放速率、烟释放及材料在燃烧时的质量损失行为进行了研究。结果表明,添加5%(质量分数)OMMT可以提高PP/EVA复合材料的阻燃性能,燃烧时的热释放速率、质量损失率以及烟释放量减少,且OMMT与无卤复配阻燃剂之间可产生阻燃协同作用,使纳米复合阻燃材料的阻燃性能、热稳定性和抑烟性进一步增强。     

基于CuAAC反应链间自交联有机-无机杂化水性聚氨酯的合成及性能

利用4,4’-二羟甲基-1,4-庚二炔功能单体作为扩链剂合成了一系列炔基接枝量不同的水性聚氨酯（WPU）,然后基于铜催化的叠氮-炔基环加成（CuAAC）反应,采用3-叠氮基丙基三乙氧基硅烷（APTES-N₃）改性炔基功能化WPU,制备了室温链间自交联有机-无机杂化WPU. 采用红外光谱（FTIR）和核磁氢谱（¹H NMR）表征了自交联有机-无机杂化WPU. 探讨了APTES-N₃接枝量对WPU膜性能和WPU乳液形态的影响. 结果表明,随着APTES-N₃含量增加,WPU膜的结晶性逐渐下降;耐水性、耐溶剂性和热稳定性逐渐增强;WPU乳液粒子黏连程度增加. 当APTES-N₃质量分数从0增大到12%时,WPU膜的拉伸强度从14.3 MPa增加到28.6 MPa.     

有机蒙脱土/天然橡胶纳米复合材料的阻燃性能研究

采用机械混炼插层法制备有机蒙脱土/天然橡胶(TMT/NR)纳米复合材料.使用X-射线衍射(XRD)和红外表征了有机蒙脱土的结构特性,并用锥形量热仪测试了纳米复合材料的燃烧性能.结果表明,有机蒙脱土/NR纳米复合材料的热释放速率(HRR)、生烟速率(SPR)等较纯天然橡胶、未改性蒙脱土/NR复合材料均所有降低,表现出较好的阻燃性能.通过对纳米复合材料的燃烧性能和燃烧残余物分析,探讨了该体系的阻燃机理.     

聚苯氧基磷酸联苯二酚酯/聚磷酸铵膨胀阻燃剂对环氧树脂阻燃性能影响研究

以聚苯氧基磷酸联苯二酚酯(PBPP)与聚磷酸铵(APP)组成复合阻燃剂,对环氧树脂(EP)进行阻燃改性.通过氧指数(LOI)、垂直燃烧(UL-94)、热失重(TGA)、锥形量热(CONE)和扫描电镜(SEM)等方法研究改性环氧树脂的阻燃性能和阻燃机理.结果表明,PBPP/APP体系对EP具有较好的阻燃性能,阻燃剂添加量为10%时能使环氧树脂的氧指数提高到29.6%,垂直燃烧等级达到UL94 V-0级,残炭量大大增加;平均热释放速率下降45.7%,热释放速率峰值下降51.0%,有效燃烧热平均值下降21.1%;TGA、CONE、SEM等综合分析显示了PBPP/APP改性后的环氧树脂比纯环氧树脂具有更高的热稳定性,燃烧后能够形成连续、致密、封闭、坚硬的焦化炭层,在聚合物表面产生有效覆盖、隔绝了氧气,改善了环氧树脂的燃烧性能.     

DOPO衍生物改性碳纳米管的制备及对聚乳酸阻燃性能的影响

以含羧基的碳纳米管(CNT-COOH)和9,10-二氢-9-氧-10-磷杂菲-10-氧化物(DOPO)衍生物DOPO-NH₂为原料, 通过酰氯化反应、 缩合反应等制备了一种新型无机-有机杂化阻燃剂—DOPO衍生物改性碳纳米管(CNT-DOPO), 利用傅里叶变换红外光谱、 透射电子显微镜、 X射线光电子能谱及热重分析等对其结构进行表征并对有机物接枝率进行了定量测试. 结果表明, DOPO-NH₂成功接枝到碳纳米管上, 接枝率约为50%. 将CNT-COOH, DOPO-NH₂和CNT-DOPO以质量分数5%添加到聚乳酸(PLA)中制备阻燃PLA复合材料. 锥形量热测试结果表明, 与纯PLA相比, PLA/5CNT-COOH, PLA/5DOPO-NH₂和PLA/5CNT-DOPO 3种复合材料的热释放速率峰值分别下降46%, 3.4%和39.8%; 炭层形貌和结构分析表明, PLA/5CNT-DOPO的炭层石墨化程度最高, CNT-DOPO₂在凝聚相阻燃方面有明显的促进作用. 流变结果表明, 碳纳米管对黏弹转变影响很明显, PLA/5CNT-COOH和PLA/5CNT-DOPO基本上表现为弹性行为. 正是由于碳纳米管的存在, 使得PLA复合材料在低频区黏度增大, 并且在燃烧后期形成了连续致密的炭层, 有效降低了材料的热释放速率和烟释放.     

核壳型纳米粒子填充PP-EVA及阻燃材料的动态燃烧行为

利用锥形量热仪(CONE)和热重分析(TGA),并结合极限氧指数(LOI)和UL-94垂直燃烧测试方法对核(PSt/OMMT)-壳(PBA)结构纳米复合粒子(CSN)填充聚丙烯(PP)-乙烯-醋酸乙烯酯共聚物(EVA)复合材料及加入无卤复配阻燃剂制备的PP-EVA/CSN/聚磷酸铵(APP)/层状氢氧化镁铝(LDH)复合阻燃材料的阻燃性能及热降解行为进行了研究。结果表明,添加10%(wt)CSN可以提高PP-EVA复合材料的阻燃性能,且PP-EVA复合体系燃烧时的热释放速率、有效燃烧热减少,热稳定性增强。CSN与APP/LDH产生阻燃协同作用,使复合阻燃材料的阻燃性能、热稳定性能进一步提高。     

膨胀阻燃硬质聚氨酯泡沫塑料热降解及燃烧产烟研究

采用热失重、X-射线光电子能谱分析、氧指数及烟密度测试等方法研究了可膨胀石墨(EG)与聚磷酸铵(APP)复配膨胀阻燃硬质聚氨酯泡沫塑料(RPUF)的热降解、燃烧性能及产烟行为.在此基础上利用锥形量热仪考察了EG/APP对磷酸三(β-氯异丙基)酯(TCPP)阻燃RPUF体系燃烧性能的影响.研究表明,EG与APP间的相互作用导致了EG/APP体系高温阶段失重速率下降、残炭量显著上升;EG/APP与RPUF之间的成炭作用以APP的化学成炭为主.与RPUF比较,RPUF/EG/APP的氧指数由19.8%提高至35.4%的同时,烟密度没有显著上升.对比EG、APP及EG/APP阻燃RPUF,体系残炭量越高、炭层耐热氧化能力越强,氧指数就越大;残炭表面越致密,产烟量就越少.添加EG/APP可显著降低含卤体系RPUF/TCPP的热释放、烟释放及CO释放速率,体现了EG与APP复合体系物理与化学膨胀结合的优势.     

不饱和聚酯片状模塑料的模压成型与性能

采用模压成型的方法制备了不饱和聚酯片状模塑料(UP-SMC)制品,通过万能试验机、热重分析、动态热机械分析、氧指数和纳米压痕技术研究了制品的力学性能、热稳定性能和阻燃性能。 结果表明,UP-SMC制品的弯曲强度和冲击强度分别达到203.4和94.2 MPa,由树脂过渡到纤维的各相微观力学性能是不同的。 该制品的玻璃化转变温度为169.4 ℃,在N₂气气氛下失重5 %(T_d5)和最大失重速率(T_dmax)对应的温度分别为333.5和389.7 ℃,600 ℃的质量保留率大于75%,极限氧指数为25.7%,表明该UP-SMC制品具有优异的力学性能和热稳定性能。     

竹基多孔碳材料的制备及其协同阻燃环氧树脂研究

以KOH为致孔剂,制备了竹基微孔多孔碳材料(PCM);将PCM与聚磷酸铵(APP)添加于环氧树脂(EP),研究了PCM协同APP阻燃EP复合材料的作用及机理.BET吸附、扫描电子显微镜(SEM)及X射线光电子能谱(XPS)分析显示,PCM6的比表面积、孔容、孔径分别为2063 m2/g、0.9 cm2/g、1.8 nm;粒径为1~5μm;表面存在C—C,C—O—,C O及COO—等活性基团.极限氧指数(LOI)、UL 94垂直燃烧及锥形量热仪(Cone)研究表明,0.8 wt%的PCM6与3.1 wt%的APP复合可使EP复合材料的LOI由24.6%提高到27.3%,热释放速率峰值降低45.4%,PCM6表现出良好的协同阻燃作用.热失重分析及XPS研究表明,PCM6提高了阻燃EP复合材料的热稳定性,催化APP释放NH3、H2O,加快了交联成炭的速度及热解产物焦磷酸(酯)的形成,由此揭示了PCM协同APP阻燃EP的作用机理.     

Fabrication of functional waterborne polyurethane/montmorillonite composites by click chemistry method

"Click" chemistry method was used to fabricate novel waterborne polyurethane (WPU)/montmorillonite (MMT) composites based on alkyne-containing WPU and azide-modified montmorillonite. The morphology of these composites was characterized by x-ray diffractometer, scanning electron microscope. The mechanical properties, thermal stability, and flame resistance of the composites were investigated by tensile, thermogravimetry and cone calorimetric experiments, etc. The experimental results show that the tensile strength, water resistance and flame retardancy of the WPU/MMT composites have been reinforced efficiently owing to the linking of MMT by click reaction.     

Influence of Fe‐MMT on the fire retarding behavior and mechanical property of (ethylene‐vinyl acetate copolymer/magnesium hydroxide) composite

In this work, Fe‐montmorillonite (Fe‐MMT) is synthesized and used as a synergistic agent in ethylene vinyl acetate/magnesium hydroxide (EVA/MH) flame retardant formulations. The synergistic effect of Fe‐MMT with magnesium hydroxide (MH) as the halogen‐free flame retardant for ethylene vinyl acetate (EVA) is studied by thermogravimetric analysis (TGA), limiting the oxygen index (LOI), UL‐94, and cone calorimetry test. Compared with that of Na‐MMT, it indicates that the synergistic effects of Fe‐MMT enhance the LOI value of EVA/MH polymer and improve the thermal stability and reduce the heat release rate (HRR). The structure and morphology of nanocomposites are studied by X‐ray diffraction (XRD) and transmission electron microscopy (TEM). The mechanical properties of the EVA composites have also been studied here, indicating that the use of Fe‐MMT reduces the amount of inorganic fillers. MH hence enhances the mechanical properties of the EVA composite while keeping the UL‐94 V‐0 rating. Copyright © 2008 John Wiley & Sons, Ltd.     

Modified montmorillonite combined with intumescent flame retardants on the flame retardancy and thermal stability properties of unsaturated polyester resins

Modified montmorillonite‐containing phytic acid (PA‐MMT) has been prepared by acid treatment and then introduced into unsaturated polyester resin (UPR) with an intumescent flame retardant (IFRs). The flame retardancy and thermal degradation of UPR/IFRs/PA‐MMT were evaluated by a limiting oxygen index (LOI) test, a vertical burning test (UL‐94), a thermogravimetric analysis (TGA), and a cone calorimeter test (CCT). Besides, the mechanical properties were studied by a universal testing machine. The LOI value of UPR/IFRs/PA‐MMT composites was increased to 29.2%. The CCT results indicated that the incorporation of PA‐MMT and IFRs significantly improved the combustion behavior of UPR. The results of the mechanical properties indicated that 1.5 wt% loading of PA‐MMT in UPR/IFRs showed the highest improvement in flexural strength and tensile strength. The flame‐retardant mechanism of PA‐MMT/IFRs was examined and discussed based on the results of combustion behavior and char analysis.     

Synthesis of functionalized α-zirconium phosphate modified with intumescent flame retardant and its application in poly(lactic acid)

A novel functionalized α-zirconium phosphate (F-ZrP) modified with intumescent flame retardant was synthesized by co-precipitation method and characterized. Poly (lactic acid) (PLA)/F-ZrP nanocomposites were prepared by melt blending method. The thermal stability and combustion behavior of PLA/F-ZrP nanocomposites were investigated by thermogravimetric analysis (TGA), limiting oxygen index (LOI), vertical burning test (UL-94), scanning electronic microscopy (SEM), and cone calorimeter test (CCT). The results showed that the addition of flame retardant F-ZrP slightly affect PLA's thermal stability, but significantly improve the flame retardancy of PLA composites. In comparison with neat PLA, the LOI value of PLA/F-ZrP was increased from 19.0 to 26.5, and the UL-94 rating was enhanced to V-0 as the loading of F-ZrP at 10%. SEM results suggested the introduction of F-ZrP in the PLA system can form compact intumescent char layer during burning. All these results showed that the F-ZrP performed good flame retardancy for PLA.     

Thermal stability and flame retardancy of LDPE/EVA blends filled with synthetic hydromagnesite/aluminium hydroxide/montmorillonite and magnesium hydroxide/aluminium hydroxide/montmorillonite mixtures

The combination of organophillised montmorillonite (MMT), synthetic hydromagnesite and aluminium hydroxide (ATH) as flame retardant system for polyethylene-based materials was studied and compared with a similar system with magnesium hydroxide, ATH and MMT. The thermal stability and the flame retardant properties were evaluated by thermogravimetric analysis (TGA), differential thermal analysis (DTA), limiting oxygen index (LOI) and cone calorimeter tests. The results indicated that the addition of montmorillonite makes it possible to reduce the total filler content to achieve the flame retardant requirements. The thermal stability of filled LDPE/EVA blends increases to a higher extent for the samples containing MMT. In the cone calorimeter tests we observed a reduction of the peak heat release rate for the sample containing montmorillonite in comparison with a sample with higher filler loading without this nanoclay. An increase of the stability of the char formed could be responsible for this favourable behaviour when montmorillonite is added.In addition, mechanical properties significantly improved for the composites containing montmorillonite both for the filler loading reduction and the reinforcement effect of the nanoclay.     

Preparation of a novel phosphorus‐containing organosilicon and its effect on the flame retardant and smoke suppression of polyethylene terephthalate

A novel phosphorus‐containing silicone flame retardant (PDPSI) was prepared by Mannish reaction, and a series of PDPSI/PET composites were prepared by melt blending method. The nuclear magnetic resonance (¹H NMR), Fourier transformation infrared (FTIR), and the thermogravimetric analyzer (TGA) results indicated that PDPSI showed network structure and owned good thermal stability, with the char residue of 62.2% at 800°C. The flame retardancy of PDPSI/PET composites was characterized by limiting oxygen index (LOI), vertical burning tests (UL‐94), and cone calorimeter (CCT). The results revealed that the addition amount of PDPSI was 5%, the LOI value of PDPSI/PET composites increased to 27.3%, and UL‐94 test passed V‐0 rating. When the PDPSI loading was 3%, PET composites showed excellent flame retardancy and smoke suppression, with a decrease in the peak heat release rate (PHRR) by 71.19% and the total smoke release (TSP) reduced from 14.4 to 11.1m². The scanning electron microscopy (SEM) and FTIR results of char residue demonstrated that the flame‐retardant mechanism of PDPSI was solid phase flame retardant. PDPSI catalyzed the aromatization reaction of PET to promote the formation of a dense and continuous carbon layer, finally improving the flame retardancy and smoke suppression properties of PET.     

Effect of ethylene-acrylic acid copolymer on flame retardancy and properties of LLDPE/EAA/MH composites

Halogen-free flame retardant linear low density polyethylene (LLDPE)/ethylene-acrylic acid copolymer (EAA) blends were prepared in a melt process using magnesium hydroxide (MH) as flame retardant. The effect of EAA on flame retardancy and properties of LLDPE/EAA/MH composites was studied. The flammability of composites was investigated using Limiting Oxygen Index (LOI) and Cone calorimeter test. The results showed that the introduction of EAA into composites apparently increased LOI from 28% to 39%, meanwhile, reduced heat release rate (HRR) and smoke production rate (SPR) according to Cone calorimeter results, which was mainly due to the uniform dispersion of MH as a result of hydrogen bonding and acid-base reaction between MH and EAA. This improved interfacial adhesion was confirmed by Scanning Electronic Microscopy (SEM). Thermogravimetric analysis (TGA) showed that EAA could enhance the thermal oxidative stability of composites. It was attributed to the formation of a stable barrier to prevent the heat and mass transfer in fire, which was confirmed by the observation of fire performance with Cone calorimeter. The crystallization and rheological behaviour of composites were studied using Differential scanning calorimeter (DSC) and oscillatory rheological measurements. Mechanical test results indicated that the addition of EAA could increase the elongation at break and impact strength of composites.     

Flammability characteristics and synergistic effect of hydrotalcite with microencapsulated red phosphorus in halogen-free flame retardant EVA composite

The flammability characteristics and synergistic effect of hydrotalcite with microencapsulated red phosphorus (MRP) in halogen-free flame retardant ethylene vinyl acetate (EVA) composite have been studied by cone calorimeter test (CCT), thermogravimetric analysis (TGA), limiting oxygen index (LOI) and UL-94 test. The results obtained by comparing the flame retardancy of hydrotalcite with magnesium hydroxide (MH) and aluminium hydroxide (AH) for their EVA composites showed that hydrotalcite has higher flame retardant effect than MH and AH at the same loading level. The CCT tests indicated that the heat release rate (HRR) and mass loss rate (MLR) of EVA composite blended with hydrotalcite greatly decreased compared with those blended with MH and AH. The LOI values of EVA/hydrotalcite composites are 3-4% higher than those of the corresponding MH composites at 40-60 wt% loading levels, and 6% higher than that of the corresponding AH composite at 40 wt% loading level. Moreover, the addition of a given amount of MRP apparently resulted in the increase of LOI value and decrease of the HRR and MLR as well the loading of hydrotalcite in EVA blend while keeping the V-0 rating in UL-94 test. However, the smoke release increased during the combustion of EVA/hydrotalcite blend containing MRP.     

Self-extinguishing polypropylene with a mass fraction of 9% intumescent additive II – Influence of highly oriented fibres

Recently, noticeably enhanced flame retardancy of multilayered self-reinforced composites, flame retarded with common ammonium polyphosphate based intumescent system, was described. In this paper the observed novel flame retardant synergism between intumescent additive system and highly oriented polymer fibres is further studied. The ignitability and combustion behaviour of flame retarded multilayer self-reinforced composites were compared to flame retardant compounds, prepared by simple melt compounding, of identical low additive contents, both when the heat was applied parallel (UL-94 tests) and perpendicular (cone calorimetric tests) with the direction of the embedded oriented tapes in self-reinforced composites. SEM and EDS analyses supported the different foaming process of the two types of samples to be understood, while the structure and character of the finally (after combustion) obtained charred layers were examined by compression tests. Considering the results of all the applied testing methods, the complex picture of the mechanism behind the enhanced flame retardant efficiency of flame retarded self-reinforced composites could be clarified.