CMC/PNIPAAm半互穿网络水凝胶的溶胀动力学研究

以羧甲基纤维素钠(CMC)和N-异丙基丙烯酰胺(NIPAAm)为原料,制备了具有温度和pH敏感性的半互穿网络(CMC／PNIPAAmsemi-IPN)水凝胶,并研究了水凝胶在不同温度和pH值条件下的溶胀行为。结果表明：在弱碱性(pH-7．4)条件下,凝胶的溶胀速率和溶胀度都随着凝胶中CMC含量的增加而增大;而在酸性(pH-1．O)条件下则相反。在弱碱性条件下,水分子在凝胶中的扩散行为都可用non-Fickian扩散来描述,水分子在凝胶中的扩散系数D随着凝胶溶胀速率的增大而增大;在酸性条件下,20℃时凝胶的溶胀过程符合non-Fickian扩散规律,而37℃时凝胶的溶胀过程符合Fickian扩散规律,但水分子的扩散系数D相差不大。     

交联聚(N-异丙基丙烯酰胺)/(海藻酸钠/聚(N-异丙基丙烯酰胺))半互穿网络水凝胶的制备及其溶胀性能

将线性聚(N-异丙基丙烯酰胺)(PNIPAAm)和海藻酸钠(SA)分子同时引入到PNIPAAm凝胶中,制备了交联聚(N-异丙基丙烯酰胺)/(海藻酸钠/聚(N-异丙基丙烯酰胺))半互穿网络(Cr-PNIPAAm/(SA/PNIPAAm)semi-IPN)水凝胶。在弱碱性条件下(pH=7.4),改变SA与线性PNIPAAm的质量比对Cr-PNIPAAm/(SA/PNIPAAm)semi-IPN水凝胶的溶胀度没有太大的影响。在酸性条件下(pH=1.0),其溶胀度随着SA与线性PNIPAAm质量比的减小而增大。由于亲水性SA与线性PNIPAAm的协同作用,Cr-PNIPAAm/(SA/PNIPAAm)semi-IPN水凝胶的消溶胀速率得到很大提高。     

温敏性PNIPAAm水凝胶对布洛芬的控制释放

采用自由基聚合法在水溶液中制备了温敏水凝胶聚N-异丙基丙烯酰胺(PNIPAAm),以非水溶性药物布洛芬(IBU)为模型药物分子,研究了该水凝胶的温敏性能及与药物IBU的相互作用,考察了不同温度下(25 ℃和37 ℃)IBU在磷酸盐缓冲溶液(PBS,pH=7.4)中的释放行为.研究结果表明:该水凝胶的最低临界溶解温度(L...     

P(γ-PGA-co-NIPAAm)水凝胶对5-氟尿嘧啶药物分子的释放行为

以γ-聚谷氨酸(γ-PGA)、N-异丙基丙烯酰胺(NIPAAm)为单体,通过自由基共聚法制备一种水凝胶缓释材料。采用扫描电镜观察水凝胶的多孔断面形貌,并研究不同温度(25℃和37℃)下水凝胶表面的亲疏水性和不同pH(2.0~10.0)时的溶胀率变化。将该共聚水凝胶用作药物缓释载体,通过紫外分光光度计法研究其对5-氟尿嘧啶(5-FU)药物分子的缓释行为。结果表明:该凝胶在酸性条件下释药速率最快,碱性条件下次之,中性条件下释放最慢,25℃下释放量与γ-PGA含量呈正相关,37℃下结果相反;该凝胶具有温度、pH双敏感性,在弱碱性条件下释放缓慢、释药量小,具有一定的靶向释药能力。     

羧甲基壳聚糖水凝胶制备及其在药物控释中的应用

以戊二醛为交联剂制备了一系列羧甲基壳聚糖pH敏感水凝胶 .研究了合成条件对羧甲基壳聚糖水凝胶溶胀性能的影响 .实验结果表明羧甲基壳聚糖的脱乙酰度、交联剂用量对水凝胶溶胀率的影响较大 .pH=3 0时 ,水凝胶收缩 ,而pH =1 0 ,5 0 ,7 4 ,9 0时 ,水凝胶溶胀 ,且在碱性条件下水凝胶的溶胀率远大于酸性条件下的溶胀率 .包埋在此水凝胶中的水杨酸释放随载药介质的pH值和水凝胶半径大小的变化而显著不同 ,pH =1 0条件下载药的水凝胶的释药率大于pH =7 4 ,12 0条件下的释药率 ,且水凝胶的半径越大 ,释药速度和释药率也越大     

温度和pH双敏性PVME/CMCS水凝胶辐射交联制备及其性能

以聚甲基乙烯基醚(PVME)和羧甲基壳聚糖(CMCS)为原料, 采用电子束辐照交联方法制备聚甲基乙烯基醚/羧甲基壳聚糖(PVME/CMCS)水凝胶, 研究了温度、pH值、CMCS含量等对PVME/CMCS水凝胶溶胀度的影响, 同时以5-氟尿嘧啶(5-Fu)作模型药物, 初步探讨了凝胶药物释放性能. 结果表明, 辐射剂量在20—40 kGy时, 凝胶分数随辐射剂量的增加而快速增加, 辐射40 kGy以后趋于平衡. 在相同辐射剂量下, 随着体系中CMCS含量的增加, 凝胶分数反而减少. 该水凝胶具有一定的温度和pH敏感性, 其低临界溶解温度(LCST)在35 ℃左右, 并且在相同时间内和25及37 ℃下的溶胀反复可逆, 表现出较快的响应性. pH<3.0和pH>5.0时, 溶胀度较大; pH值为3.0~5.0时, 凝胶网络由于静电力收缩, 溶胀度较小. CMCS含量的增加和辐射剂量的减小均可提高凝胶载药量. 药物释放时间可通过改变体系中CMCS的含量和辐射剂量来调节.     

NIPAAm系互穿网络凝胶的合成及载药释药性能研究

合成了三种亲疏水性不同的温度及pH敏感的PAAc／P（NIPAAm-co-BMA）、PAAc／PNIPAAm和PAAc／P（NIPAAm-co-AAm）互穿网络（IPN）水凝胶,以水杨酸钠和水杨酸为模型药物,研究了温度、pH值及药物和凝胶的亲疏水性相互作用对模型药物释药性能的影响。研究结果表明,随着凝胶亲水性的增强,水杨酸钠的载药率提高,释药率也越大;相反疏水性增强也有利于提高水杨酸的载药率;IPN凝胶在水中的释药过程属于溶胀支配型释放,药物释放率随凝胶的亲水性增强而增强,同时,载药凝胶在45℃水中的释药率大于25℃时的释药率。在25℃时,水杨酸在pH=2．2的缓冲溶液中几乎不释放,而在pH=7．4的缓冲溶液中能以较快的速率释放。     

聚丙烯酰胺/聚异丙基丙烯酰胺互穿网络水凝胶的制备与性能(英文)

采用分步法用电子加速器辐射合成了聚丙烯酰胺(PAAm)/聚异丙基丙烯酰胺(PNIPAAm)互穿网络水凝胶,并考察了温度、pH值、离子强度对其溶胀性能的影响.研究表明:互穿水凝胶具有温度敏感性,且其体积相变与互穿网络中PAAm和PNIPAAm含量有关,随着网络中PAAm含量的增加水凝胶的体积相变趋于平缓,可以通过改变PAAm和PNIPAAm的组成比来控制水凝胶的体积相变行为.此外,互穿水凝胶还具有pH敏感性和一定的抗盐性.     

聚乙烯醇/羧甲基壳聚糖共混水凝胶的辐射合成及性能

采用电子加速器辐照法制备了聚乙烯醇(PVA)/羧甲基壳聚糖(CMCH)共混水凝胶;研究了PVA与CMCH的配比、辐照剂量、温度以及pH值对PVA/CMCH共混水凝胶性能的影响.实验发现,PVA与CMCH在辐照剂量为40 kGy、配比为w(PVA)/w(CMCH)=5/1的条件下可得到强度较好的PVA/CMCH共混水凝胶,该水凝胶具有一定的温度和pH敏感性:在5~20℃时具有较高的溶胀率,温度在20℃以上溶胀率较低;水凝胶在pH<4.0和pH>6.0时溶胀率均较大,而当pH为4.0~6.0时溶胀率较小.     

聚(N-异丙基丙烯酰胺)/聚丙烯酰胺无机/有机互穿网络水凝胶的制备及表征

通过紫外引发聚合方法制备了无机交联的聚(N-异丙基丙烯酰胺)(PNIPAAm)/有机交联的聚丙烯酰胺(PAAm)互穿网络(IPN)水凝胶.利用FTIR和SEM分别表征了凝胶的化学结构和内部形态;测定了凝胶在高温(50℃)时的退溶胀性能;利用DMA和DSC分别研究了凝胶的储能模量随温度的变化及热相转变行为.研究表明,该IPN凝胶具有温度敏感性;与未互穿的无机交联PNIPAAm凝胶相比,IPN凝胶具有多孔的网络结构和超快的响应速率,如10min内失去90%的水;其储能模量增加了3～4倍,相转变行为变弱,而最低临界溶解温度(LCST)提高了1.4℃.     

Solvent extraction separation of In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/ with sulphoxides

Solvent extraction studies have been made on some metals: In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/, from ammonium thiocyanate solutions by dialkyl sulphoxides. Separation of these metals from one another can be achieved by suitable choice of the extracted conditions. The nature of the extractable metal species has been elucidated.     

Simultaneous propane dehydrogenation andco2hydrogenation overCrOx/SiO2catalyst

Summary Single reverse water-gas shift (RWGS) and dehydrogenation of propane with CO₂(DH-CO₂) reactions in the presence and absence of the CrO_x/SiO₂ catalyst have been studied between 673 and 873 K. It was found that the CrO_x/SiO₂ catalyst is active both in the dehydrogenation of propane and in the RWGS reactions. The obtained results suggest that the dehydrogenation of propane to propene in the presence of CO₂on CrO_x/SiO₂can be facilitated by the RWGS reaction.</o:p>     

An investigation of the promotional effect of propylene or propane traces on the activity of sulfatedPt/g-Al2O3andPt-Sn/g-Al2O3inCH4combustion

Summary A strong promoting effect of the presence of C₃H₈or C₃H₆was determined for the combustion of CH₄in excess oxygen, over pre-sulfated 1%Pt/g-Al₂O₃and pre-sulfated 1%Pt-2%Sn/g-Al₂O₃catalysts.</o:p>     

Synthesis of chlorobis/β-diketonato/oxotechnetium/V/ and tris/β-diketonato/technetium/III/ complexes

Chlorobis/-diketonato/ oxotechnetium/V/ complexes [TcOCl/-dik/₂, -diketone=acetylacetone, benzoylacetone and dibenzoylmethane] were newly synthesized using macroamount of⁹⁹Tc. These complexes were further separated into geometrical isomers. Furthermore, an improvement of the yields for the syntheses of tris/-dike-tonato/technetium/III/ complexes [Tc/-dik/₃, -diketone=acetylacetone, benzoylacetone and 2-thenoyltrifluoroacetone] was examined using Tc/III/-thiourea complexes as a starting material.     

Crystal structure of Na3PO4 · 12H2O

The crystal structure of trisodium monophosphate hemihydrate was determined. The space group is $\text{C2}\text{c}$ and a unit cell contains eight formula units. The unit cell dimensions of $\text{Na}{}_3\text{PO}{}_4\text{·}\text{1}\text{2}\text{H}{}_2\text{O}$ are a = 9.631(3), b = 5.416(2), c = 16.938(8) Å, β = 102.60(5)°. The final R value is 0.027 for a set of 1430 independent reflections. This atomic arrangement is mainly a three-dimensional network of distorted NaO₆ octahedra. The hydrogen bonding scheme is given.     

Direct synthesis of dimethyl carbonate ?from CH3OH AND CO2 by H3PW12O40/CexTi1-xO2 catalyst

Summary Ce_xTi_1-xO₂ and H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts were prepared using a sol-gel method, and applied to the direct synthesis of dimethyl carbonate from methanol and carbon dioxide. H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ showed a better catalytic performance than the corresponding Ce_xTi_1-xO₂, due to the bifunctional catalysis of Br?nsted acid sites (provided by H₃PW₁₂O₄₀) and base sites (provided by Ce_xTi_1-xO₂). H₃PW₁₂O₄₀/Ce_0.1Ti_0.9O₂ showed the highest catalytic performance among the H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts.     

Carbon black and propylene oxidation over Ru/CoxMgyAl2Oz catalysts

The effects of Co_xMg_yAl₂O_z mixed oxides composition and ruthenium addition on the oxidation of propylene and carbon black (CB) were investigated. Different reactive cobalt and ruthenium oxide species were formed following calcination at 600 °C. The addition of ruthenium was beneficial for the CB oxidation under “loose contact” conditions and for propylene oxidation when the cobalt content was intermediate to low. The calculated activation energy for CB oxidation was decreased from 151 kJ mol⁻¹ for the uncatalyzed reaction to 111 kJ mol⁻¹ over the best catalyst.     

Structure refinement, dielectric, pyroelectric and Raman characterizations of Ba1−xLax(1−y)/2Euxy/2Nax/2TiO3 solid solution

The perovskite-type oxides Ba_1−xLa_x(1−y)/2Eu_xy/2Na_x/2TiO₃ (0?x?0.5 and xy=0.04) were synthesized and characterized by X-ray diffraction as well as dielectric measurements and Raman spectroscopy. The crystal structure of these ceramics has been determined by the Rietveld refinement powder X-ray diffraction data at room temperature. These compounds crystallize at room temperature in tetragonal space group P4mm for 0?x?0.1 and in the cubic group for 0.2?x?0.5. The phase transition temperature T_C (or T_m) decreases as x content increases. The degree of diffuseness of the phase transition is more pronounced for higher x content, implying the existence of a composition-induced diffuse phase transition of the ceramics with x?0.1. The evolution of the Raman spectra was studied as a function of various compositions at room temperature. The polarization state was checked by pyroelectric measurements.     

LixZryOz三元化合物的制备及表征

采用高温固相法制备了4种高纯度晶相组成的LixZryOz三元化合物,研究了焙烧温度、时间、反应物的种类和初始反应物物质的量比对产物组成的影响,进一步用XRD、SEM及BET分析方法对产物的晶相结构、表面形貌及比表面积进行了表征.实验结果表明,Li2CO3与ZrO2在适当条件下可以合成得到单斜相Li3ZrO3;以LiOH替代Li2CO3,在适当条件下可以分别合成得到四方相Li2ZrO3和三斜/单斜相Li6Zr2O7;进一步以Zr(NO3)4·5H2O代替Zr02,可将单斜相Li6Zr2O7的制备时间由96 h缩短至24 h.SEM照片显示产物硬团聚明显,粒径分布在1～10μm间,BET分析表明样品比表面积处于1.0～9.0 m2·g-1间分布,反应过程中锂的过量以及长时间高温焙烧是引起产物粒径长大和产生硬团聚的主要原因.     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.