Synthesis and mechanical behavior of functionally gradient polyisocyanurate materials based on hydroxy-terminated butadiene rubber

Functionally gradient polyisocyanurate-based structural materials in which the modulus of elasticity could be arbitrarily varied over a continuos range from 3 to 2000 MPa were prepared from hydroxy-terminated butadiene rubber and diphenylmethane diisocyanate. The materials are synthetically obtainable both via bulk polymerization (molding) and as composite materials with fillers of any type, including both highly porous compliant fillers that have no effect on the mechanical properties of the polymer matrix and reinforcing fillers, such as carbon and glass clothes. The trends in the main properties were studied; it was found that, over the entire range of elastic moduli relevant to the glass-to-rubber transition, the materials retain the elastic behavior inherent in polymer glasses, not the viscoelastic behavior characteristic of the transitional region between the glassy and rubbery states.     

Engineering micromechanics of soft porous crystals for negative gas adsorption

Framework materials at the molecular level, such as metal–organic frameworks (MOF), were recently found to exhibit exotic and counterintuitive micromechanical properties. Stimulated by host–guest interactions, these so-called soft porous crystals can display counterintuitive adsorption phenomena such as negative gas adsorption (NGA). NGA materials are bistable frameworks where the occurrence of a metastable overloaded state leads to pressure amplification upon a sudden framework contraction. How can we control activation barriers and energetics via functionalization of the molecular building blocks that dictate the frameworks'' mechanical response? In this work we tune the elastic and inelastic properties of building blocks at the molecular level and analyze the mechanical response of the resulting frameworks. From a set of 11 frameworks, we demonstrate that widening of the backbone increases stiffness, while elongation of the building blocks results in a decrease in critical yield stress of buckling. We further functionalize the backbone by incorporation of sp³ hybridized carbon atoms to soften the molecular building blocks, or stiffen them with sp² and sp carbons. Computational modeling shows how these modifications of the building blocks tune the activation barriers within the energy landscape of the guest-free bistable frameworks. Only frameworks with free energy barriers in the range of 800 to 1100 kJ mol⁻¹ per unit cell, and moderate yield stress of 0.6 to 1.2 nN for single ligand buckling, exhibit adsorption-induced contraction and negative gas adsorption. Advanced experimental in situ methodologies give detailed insights into the structural transitions and the adsorption behavior. The new framework DUT-160 shows the highest magnitude of NGA ever observed for nitrogen adsorption at 77 K. Our computational and experimental analysis of the energetics and mechanical response functions of porous frameworks is an important step towards tuning activation barriers in dynamic framework materials and provides critical design principles for molecular building blocks leading to pressure amplifying materials.

We characterise the elastic properties of molecular building blocks and how they impact the mechanical properties of soft porous crystals.     

Mesoscopic model for mechanical characterization of biological protein materials

Mechanical characterization of protein molecules has played a role on gaining insight into the biological functions of proteins, because some proteins perform the mechanical function. Here, we present the mesoscopic model of biological protein materials composed of protein crystals prescribed by Go potential for characterization of elastic behavior of protein materials. Specifically, we consider the representative volume element (RVE) containing the protein crystals represented by C(alpha) atoms, prescribed by Go potential, with application of constant normal strain to RVE. The stress-strain relationship computed from virial stress theory provides the nonlinear elastic behavior of protein materials and their mechanical properties such as Young's modulus, quantitatively and/or qualitatively comparable with mechanical properties of biological protein materials obtained from experiments and/or atomistic simulations. Further, we discuss the role of native topology on the mechanical properties of protein crystals. It is shown that parallel strands (hydrogen bonds in parallel) enhance the mechanical resilience of protein materials.     

Mechanical Properties of SiO2-PMMA Based Hybrid Organic-Inorganic Thin Films

Nano-indentations using a Berkovich indenter were performed in order to analyze the mechanical properties of hybrid organic-inorganic coatings. This technique allows to measure low load deformations and therefore to estimate quantitatively mechanical properties of the coatings. The elastic modulus and the hardness were determined on the basis of the load-displacement curve. We report results obtained for class II hybrid coatings based on SiO₂-PMMA prepared by sol-gel process. The effects of coating composition were investigated.     

Investigation of mechanical properties of insulin crystals by atomic force microscopy

Mechanical properties of protein crystals and aggregates depend on the conformational and structural properties of individual protein molecules as well as on the packing density and structure within solid materials. An atomic force microscopy (AFM)-based approach is developed to measure the elastic modulus of small protein crystals by nanoindentation and is applied to measure the elasticity of insulin crystals. The top face of the crystals deposited on mica substrates is identified as the (001) face. Insulin crystals exhibit a nearly elastic response during the compression cycle. The elastic modulus measured on the top face has asymmetric distribution with a significant width. This width is related to the uncertainty in the deflection sensitivity. A model that takes into account the distribution of the sensitivity values is used to correct the elastic modulus. Measurements performed in aqueous buffer on several crystals at different locations with three different AFM probes give a mean elastic modulus of 164 +/- 10 MPa. This value is close to the static elastic moduli of other protein crystals measured by different techniques that are usually measured in the range from 100 MPa to 1 GPa. The measured modulus of insulin crystals falls between the elastic modulus values of insulin amyloid fibrils measured previously at two orthogonal directions (a modulus of 14 MPa was measured by compressing the fibril in the direction perpendicular to the fibril axis, and a modulus of 3.3 GPa was measured in the direction along the fibril axis). This comparison indicates the heterogeneous structure of fibrils in the direction perpendicular to the fibril axis, with a packing density of the amyloid fibril core that is higher than the average packing density in insulin crystals. The mechanical wear of insulin crystals is detected during AFM measurements. In nanoindentation experiments on insulin crystal, the compressive load by the AFM tip ( approximately 1 nN, corresponding to a pressure of around 5 MPa) occasionally removes protein molecules from the top or the second top layer of insulin crystal in a sequential manner. The molecular model of this surface damage is proposed. In addition, the removal of the multiple layers of molecules is observed during the AC-mode imaging in aqueous buffer. The number of removed layers depends on the scan size.     

Synthesis and Mechanical Properties of sub 5-μm PolyUiO-66 Thin Films on Gold Surfaces

Metal-organic framework (MOF) thin films currently lack the mechanical stability needed for electronic device applications. Polymer-based metal-organic frameworks (polyMOFs) have been suggested to provide mechanical advantages over MOFs, however, the mechanical properties of polyMOFs have not yet been characterized. In this work, we developed a method to synthesize continuous sub-5 μm polyUiO-66(Zr) films on Au substrates, which allowed us to undertake initial mechanical property investigations. Comparisons between polyUiO-66 and UiO-66 thin films determined polyUiO-66 thin films exhibit a lower modulus but similar hardness to UiO-66 thin films. The initial mechanical characterization indicates that further development is needed to leverage the mechanical property advantages of polyMOFs over MOFs. Additionally, the demonstration in this work of a continuous surface-supported polyUiO-66 thin film enables utilization of this emerging class of polyMOF materials in sensors and devices applications.     

Mechanical Properties of Dense Zeolitic Imidazolate Frameworks (ZIFs): A High‐Pressure X‐ray Diffraction,Nanoindentation and Computational Study of the Zinc Framework Zn(Im)2, and its Lithium?Boron Analogue,LiB(Im)4

The dense, anhydrous zeolitic imidazolate frameworks (ZIFs), Zn(Im)₂ ( 1 ) and LiB(Im)₄ ( 2 ), adopt the same zni topology and differ only in terms of the inorganic species present in their structures. Their mechanical properties (specifically the Young’s and bulk moduli, along with the hardness) have been elucidated by using high pressure, synchrotron X‐ray diffraction, density functional calculations and nanoindentation studies. Under hydrostatic pressure, framework 2 undergoes a phase transition at 1.69 GPa, which is somewhat higher than the transition previously reported in 1 . The Young’s modulus (E) and hardness (H) of 1 (E≈8.5, H≈1 GPa) is substantially higher than that of 2 (E≈3, H≈0.1 GPa), whilst its bulk modulus is relatively lower (≈14 GPa cf. ≈16.6 GPa). The heavier, zinc‐containing material was also found to be significantly harder than its light analogue. The differential behaviour of the two materials is discussed in terms of the smaller pore volume of 2 and the greater flexibility of the LiN₄ tetrathedron compared with the ZnN₄ and BN₄ units.     

Mechanical properties of fluorinated ethylene propylene (FEP) foils in use for neutrino detector project

The use of fluorinated ethylene propylene (FEP) foils as engineering materials for aerospace, solar thermal collector and neutrino detector applications has attracted considerable attention in recent decades. Mechanical properties are indispensable for analyzing corresponding structural behavior to meet the demands of safety and serviceability. In this paper, uniaxial tensile tests taking into account loading speeds, uniaxial tensile cyclic tests in terms of stress amplitude and loading cycles and creep tests considering loading stress and time were carried out to characterize mechanical properties. For uniaxial tensile properties, elastic modulus, yield stress, breaking strength and elongation were analyzed in detail. It is found that these mechanical properties except breaking elongation increased with loading speeds and that mechanical properties obtained in transverse direction were more sensitive than those obtained in machine direction. For cyclic properties, elastic modulus and ratcheting strain tended to be stable after certain cycles, demonstrating that cyclic elastic moduli were more suitable for analyzing structural behavior than those obtained in uniaxial tensile experiments. For creep properties, apparent strain at 6 MPa suggested that special attention was necessary for analyzing structural behavior if maximum stress was larger than 6 MPa. In general, this study could provide useful observations and values for understanding mechanical properties of FEP foils.     

Nanoindentation of biodegradable cellulose diacetate‐graft‐poly(L‐lactide) copolymers: Effect of molecular composition and thermal aging on mechanical properties

Nanoindentation of cellulose diacetate‐graft‐poly(lactide)s (CDA‐g‐PLLAs) synthesized by ring opening graft copolymerization of L ‐lactide in bulk onto the residual hydroxyl positions on CDA were conducted to investigate the effect of the molecular composition and thermal aging on mechanical properties and creep behavior. Continuous stiffness measurement (CSM) technique was used to obtained hardness and elastic modulus. These material properties were expressed as a mean value from 100 to 300 nm depths and an unloading value at final indentation depth. The hardness and elastic modulus in all CDA‐g‐PLLAs were higher than those in pure CDA, indicating that the introduction of PLLA increases the hardness and elastic modulus. With an increase of crystallinity by thermal aging, the hardness and elastic modulus were increased in both CDA‐g‐PLLA and PLLA. The creep test performed by CSM showed that the creep strain of CDA was decreased by the grafting of PLLA. Thermal aging decreased the creep strain of CDA‐g‐PLLA and PLLA. With an increase of holding time, hardness was decreased, whereas elastic modulus was kept almost constant. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1114–1121, 2007     

Theoretical assessment of structural,mechanical, and thermodynamic properties of Pd2Al

The physical properties, namely structural, mechanical, and thermodynamic properties, of Pd₂Al intermetallic compound were explored through first-principles calculations within the framework of density functional theory. The calculated lattice constants were consistent with the available experimental data. The calculated elastic constants revealed that Pd₂Al was mechanically stable. By the predicted elastic constants, several related properties, namely Cauchy pressures, shear anisotropy factors, directional Young's modulus, bulk, shear and Young's moduli, the ratio of K/G, Vickers hardness, sound velocity, and minimum thermal conductivity for Pd₂Al were evaluated. According to the calculated results, it was found that Pd₂Al possesses a highly anisotropic feature and behaves in a ductile manner with low stiffness. Finally, temperature-dependence of thermodynamic properties, namely Debye temperature and heat capacity, were also evaluated through the quasi-harmonic Debye model.     

Nanomechanical measurements with AFM in the elastic limit

With increasing interest in nanoscience and nanotechnology, the fundamental underpinnings of what makes materials strong and durable are under critical investigation. Recent findings suggest that when materials are reduced in extent to nanoscopic proportions, they exhibit enhanced strength, specifically in the form of higher moduli than are measured on macroscopic objects of the same composition. Force-deformation behavior of nanostructures subjected to concentrated loads, such as with atomic force microscopy (AFM), can yield detailed information and insight about their local mechanical properties. We review and evaluate the effectiveness of deformation and indentation tests used in determining the elastic modulus of nanobeams, nanosprings, thin films, biological samples, dendrimers, and fluid droplets. Obstacles yet remain in the determination of absolute, quantitative modulus data at the nanoscale. In spite of basic limitations, recent developments in advanced nanomechanical techniques will facilitate improvement in our understanding of material strength and aging from molecules and colloids to the macroscale.     

Micromechanical assessment of PMMA microcapsules containing epoxy and mercaptan as self-healing agents

Mechanical properties of microcapsule shell have great influence on microcapsule suitability as a mechanical trigger in a self-healing composite. The elastic modulus and hardness of polymethyl methacrylate (PMMA) microcapsules containing epoxy prepolymer (EC 157) and pentaerythritol tetrakis (3-mercaptopropionate) (PETMP) as healing agents were investigated using nanoindentation technique. The influence of the PMMA average molecular weight (M_W), the kind of core material, and the mechanical mixing rate on the mechanical properties of the microcapsule shell were studied using the Taguchi experimental design approach. The results indicated that the most important factors which affect the elastic modulus and the hardness of microcapsules shell are the Mw of PMMA and the kind of core material. The average elastic modulus of PMMA shell of epoxy and mercaptan-loaded microcapsules was found between 2.386 and 3.495 GPa. The hardness of PMMA shell of healing agent microcapsules was obtained in the range of 0.064–0.219 GPa. This constitutes essential knowledge in order to design capsules with tailored properties for self-healing materials.     

Hydrogel microspheres: influence of chemical composition on surface morphology, local elastic properties, and bulk mechanical characteristics

Hydrogel microspheres, beads, and capsules of uniform size, differing in their chemical composition, have been prepared by electrostatic complex formation of sodium alginate with divalent cations and polycations. These have served as model spheres to study the influence of the chemical composition on both surface characteristics and bulk mechanical properties. Resistance to compression experiments yielding the compression work clearly identified differences as a function of the composition, with forces at maximal compression in the range of 34-455 mN. The suitability and informative value of atomic force microscopy have been confirmed for the case where surface characterization is performed in a liquid environment equivalent to physiological conditions. Surface imaging and mechanical response to indentation revealed different average surface roughness and Young's moduli for all hydrogel types ranging from 0.9 to 14.4 nm and from 0.4 to 440 kPa, respectively. The hydrogels exhibited pure elastic behavior. Despite a relatively high standard deviation, resulting from both surface and batch heterogeneity, nonoverlapping ranges of Young's moduli were reproducibly identified for the selected model spheres. The findings indicate the reliability of contact mode atomic force microscopy to quantify local surface properties, which may have an impact on the biocompatibility of alginate-based hydrogel materials of different composition and conditions of preparation. Moreover, it seems that local elastic properties and bulk mechanical characteristics are subject to analogous composition influences.     

Flexible microporous coordination polymers

In a decade, many porous coordination polymers have been synthesized, providing a variety of properties ranging from storage, separation and exchange of guests in their cavities, magnetism, conductivity and catalysis by their frameworks. Recent advent of flexible porous coordination polymers, which exhibit elastic guest accommodation in contrast to rigid three-dimensional (3-D) frameworks of conventional porous materials, have acquired a position as a new class of porous materials. Such flexible porous properties induce highly selective guest accommodation and magnetic modulation, which could now be a unique class of practical materials. In this review, we introduce recent flexible porous coordination polymers (3-17) and their functional properties, categorizing with the four types of pores with framework deformation.     

Elastic properties of YAG: First-principles calculation and experimental investigation

The hardness and elastic stiffness of Y₃Al₅O₁₂ (YAG) were investigated by first-principles calculations and experiments. The mechanical properties including the second-order elastic coefficients, hardness, bulk modulus, Young's modulus and shear modulus were calculated by density functional theory (DFT). The calculated results were in good agreement with the experimental values. The hardness of YAG is mainly attributed to Al_tet–O bonds. The elastic anisotropy of YAG was discussed. Zener anisotropy parameter of YAG is close to unit and its universal anisotropy index is very close to zero, which indicates the structure of YAG is nearly centrosymmetric. The longitudinal and transverse sound velocities and Debye temperature were also investigated.     

分子动力学模拟浓度和温度对TATB/PCTFE PBX力学性能的影响

为探讨高聚物粘结炸药(Polymer Bonded Explosive, PBX)的力学性能随温度和高聚物浓度而变化的规律, 用分子动力学(MD)方法和compass力场, 对著名高能炸药1,3,5-三氨基-2,4,6-三硝基苯(TATB)与常用高聚物粘结剂聚三氟氯乙烯(PCTFE)所构成的TATB/PCTFE PBX进行模拟计算. 结果表明, 在一定范围内, 随高聚物浓度的增加, PBX的弹性系数和模量减小, 表明其刚性减小、弹性增加; 而随温度的升高, PBX的刚性减小、弹性增强. 还发现PBX的结合能随浓度增高而增大, 随温度升高而减小.     

二元Ni-Al合金极端条件下的弹性和热力学性能：全电子准谐波近似

通过在原子尺度上建模来研究Al、NiAl和Ni3Al合金在极端高温和高压下的点阵常数、弹性常数、弹性模量、泊松比和弹性各向异性因子等性质．计算得到的弹性常数均满足相应的力学稳定条件．由于NiAl和Ni3Al具有较高的B／G值,在0～30GPa内都属于延展性材料．通过包含电子热运动对体系吉布斯自由能贡献的全电子准谐近似方法,得到了高温高压下Al、NiAl和Ni3Al合金的热膨胀系数、体积模量、热容和熵等．计算值与已有的实验值和理论值符合较好．     

Magnetic and mechanical anisotropy in a manganese 2-methylsuccinate framework structure

Hybrid inorganic-organic framework materials exhibit unique properties that can be advantageously tuned through choice of the inorganic and organic components and by control of the crystal structure. We present a new hydrothermally prepared 3D hybrid framework, [Mn(2-methylsuccinate)](n) (1), comprising alternating 2D manganese oxide sheets and isolated MnO(6) octahedra, pillared via syn, anti-syn carboxylates. Powder magnetic characterization shows that the compound is a homospin Mn(II) ferrimagnet below 2.4 K. The easy-axis is revealed by single-crystal magnetic susceptibility studies and a magnetic structure is proposed. Anisotropic elastic moduli and hardness, observed through nanoindentation on differing crystal facets, were correlated with specific structural features. Such measurements of anisotropy are not commonly undertaken, yet allow for a more comprehensive understanding of structure-property relationships.     

Sonocrystallization Yields Monoclinic Paracetamol with Significantly Improved Compaction Behavior

Ultrasound‐assisted crystallization (sonocrystallization) was used to prepare a mixture of nano‐ and micrometer‐sized crystals of the monoclinic form of paracetamol—a widely used analgesic known for its particularly problematic mechanical behavior under compression (i.e. poor tabletability). The nano‐ and micrometer‐sized crystals yielded a powder which exhibits elastic moduli and bulk cohesions that are significantly higher than those observed in samples consisting of macrometer‐sized crystals, thus leading to enhanced tabletability without the use of excipients, particle coating, salt, or cocrystal formation. Experimental compaction and finite element analysis were utilized to rationalize the significantly improved compaction behavior of the monoclinic form of paracetamol.     

Nanoscale compression of polymer microspheres by atomic force microscopy

Atomic force microscopy (AFM) was employed to probe the mechanical properties of surface-charged polystyrene microspheres with 1-12 mol% of vinylbenzyl(trimethyl)ammonium chloride (VBTA) units. On the basis of Hertz's theory of contact mechanics, compressive moduli between 1 and 2 GPa were measured by the analysis of force-displacement curves captured on the particles via the force-volume technique. The deformation of the top of the polystyrene particles by the AFM tip was used to calculate the surface modulus. The compressive moduli are slightly less than the moduli of polystyrene bulk materials. The modulus of the polystyrene microspheres increases with an increase of the VBTA content.