Latent heat nano composite building materials

Heat storage for heating and cooling of buildings reduces the conventional energy consumption with a direct impact on CO₂ emissions. The goal of this study was to find the physico-chemical fundamentals for tailoring phase change material (PCM)-epoxy composites as building materials depending on phase change temperature and latent heat using the optimal geometry for each application. Thus, some nano-composite materials were prepared by mixing a PCM with large latent heats with epoxy resin and Al powder. Some polyethylene glycols of different molecular weights (1000, 1500, and 2000) were used as PCMs. Subsequently these PCM-epoxy composites were thermo-physically characterized by DSC measurements and found to be suitable for building applications due to their large latent heat, appropriate phase change temperature and good performance stability. Moreover these cross-linked three dimensional structures are able to reduce the space and costs for encapsulation.     

The investigation of thermal conductivity and energy storage properties of graphite/paraffin composites

Phase change materials (PCM) have been extensively scrutinized for their widely application in thermal energy storage (TES). Paraffin was considered to be one of the most prospective PCMs with perfect properties. However, lower thermal conductivity hinders the further application. In this letter, we experimentally investigate the thermal conductivity and energy storage of composites consisting of paraffin and micron-size graphite flakes (MSGFs). The results strongly suggested that the thermal conductivity enhances enormously with increasing the mass fraction of the MSGFs. The formation of heat flow network is the key factor for high thermal conductivity in this case. Meanwhile, compared to that of the thermal conductivity, the latent heat capacity, the melting temperature, and the freezing temperature of the composites present negligible change with increasing the concentration of the MSGFs. The paraffin-based composites have great potential for energy storage application with optimal fraction of the MSGFs.     

Development of a model for compensating the influence of temperature gradients within the sample on DSC-results on phase change materials

The use of phase change materials (PCMs) in thermal storage is not a new concept, but engineers are continually finding new ways to utilize them in a wide range of applications. A PCM takes advantage of high latent heat in the phase change process to store large amounts of heat while undergoing only a small change in temperature. This property makes PCMs suitable for thermal storage purposes in a wide range of engineering applications. Due to the nature of these applications, it is vital to have a precise knowledge of the thermal characteristics of any PCM. Unfortunately, due to the low thermal conductivities and high latent heats found in PCMs, current measuring tools such as differential scanning calorimetry, provide inconsistent results. This paper conjectures that these errors come from the effects of low thermal diffusivity samples as well as improper data analysis methods.     

Detection of joint capsule changes by differential scanning calorimetry (DSC) in different types of hip disorders to evaluate surgical techniques (a preliminary report)

In this study, paraffin-/ultrasonic-treated diatomite was characterized for use as phase change material (PCM) for thermal energy storage in buildings. The diatomite was treated with ultrasound at various periods of time. The diatomite treated with ultrasound for 60 min (DA-60) was the optimum condition providing the highest surface area without structural degradation. The melting point and latent heat of the paraffin/DA-60 composite PCM were 59 °C and 45.90 J g^?1, respectively. The obtained form-stable PCM had good thermal reliability after 500 cycles of thermal cycling test. The thermal performance of PCM was tested by incorporating the paraffin/DA-60 composite PCM into gypsum board. The results showed that the gypsum board containing the paraffin/DA-60 composite PCM had better thermal energy absorption and release characteristics than those of the control sample. The incorporation of paraffin/DA-60 composite PCM into suitable building materials could thus considerably reduce the energy consumption of cooling system in buildings.     

Thermal performance evaluation of a solar air heater with and without thermal energy storage

This communication presents the experimental study and performance analysis of a solar air heater with and without phase change material (PCM) viz. paraffin wax and hytherm oil. There are three different arrangements viz. without PCM, with PCM and with hytherm oil to study the comparative performance of this experimental system. Inlet, outlet temperatures and radiation with respect to time have been recorded and found that the output temperature in case with thermal energy storage (TES) is higher than that of without TES, besides, the outlet temperature with paraffin wax is slightly greater than that of with hytherm oil. Also there is no energy gain in the evening in case of without TES but in case of with TES there is a heat gain for around 4 h in the evening which gives the backup for hot air for around four more hours which is the main advantage of this systems with TES. Based on the data, the efficiency of the system has been calculated and it is noted that the efficiency in the case of heat storage is higher than that of without TES, besides the efficiency in the case of the paraffin wax is slightly higher than that of the hytherm oil case.     

High-conductivity nanomaterials for enhancing thermal performance of latent heat thermal energy storage systems

Journal of Thermal Analysis and Calorimetry - Dispersing high-conductivity nanomaterials into phase change materials (PCM) of latent heat thermal energy storage systems (LHTESS) is expected to...     

A cost-effective form-stable PCM composite with modified paraffin and expanded perlite for thermal energy storage in concrete

Journal of Thermal Analysis and Calorimetry - High thermal conductivity in phase change materials (PCM) is preferred in thermal energy storage (TES) systems. Carbon additives are considered as...     

Thermal energy storage behavior of composite using hybrid nanomaterials as PCM for solar heating systems

In this study, thermal and heat transfer characteristics of the newly prepared composite as phase change material (PCM) comprising paraffin and hybrid nanomaterials (50 % CuO–50 % TiO₂) have been investigated for solar heating systems. Composite PCMs with 0.25, 0.5, 0.75, and 1.0 mass% of hybrid nanomaterials were prepared individually for assessing their better performances than paraffin alone. Sodium dodecylbenzene sulfonate (SDBS) was preferred as the surfactant to ensure the dispersion stability of the nanomaterials in the paraffin and mass fraction of SDBS was 1.2 times of the mass fraction of hybrid nanomaterials in the paraffin. The thermal properties of the composite PCMs were determined by differential scanning calorimetry in terms of mass fractions of hybrid nanomaterials and number of thermal cycles. The thermal stabilities of the paraffin and composite PCMs were tested by thermogravimetric analyzer. The thermal conductivity and viscosity of the paraffin due to the addition of various mass fractions of CuO, TiO₂, and hybrid nanomaterials were determined by LFA 447 NanoFlash analyzer and Brookfield DV-III Ultra programmable rheometer, respectively. The experimental results proved that the heating and cooling rates of composite PCMs were faster due to the dispersion of hybrid nanomaterials. For composite PCM with 1.0 mass% of hybrid nanomaterials, the melting and freezing times were reduced by 29.8 and 27.7 %, respectively, as compared with the paraffin.     

Study on thermal properties of organic ester phase-change material embedded with silver nanoparticles

This study investigates the thermal properties of new silver nano-based organic ester (SNOE) phase-change material (PCM) in terms of latent heat capacity, thermal conductivity and heat storage and release capabilities experimentally. Spherical-shaped surface-functionalized crystalline silver nanoparticles (AgNP) prepared were embedded in mass proportions of 0.1 through 5.0 wt% into the pure (base) PCM. Experimental results reveal that dispersion of AgNP into PCM was effective, only physical and no chemical interaction between AgNP and PCM has been exhibited; thereby phase-change temperature of SNOE PCMs were acceptable. These are essential characteristics for SNOE PCMs which signified their thermal and chemical stability on long term. Test results suggest that while compared to pure PCM, degree of supercooling was reduced by 11.7–6.8 % for aforesaid mass proportions of AgNP, whereas latent heat capacities decreased by 7.88 % in freezing and 8.91 % in melting. The interdependencies between thermophysical properties in improving nucleation and growth rate of stable SNOE PCM crystals were signified and discussed. Thermal conductivity of SNOE PCMs were enhanced from 0.284 to 0.765 W m^?1 K^?1 which was expected to be a 10–67 % increase for the above mass loading of AgNP. Furthermore, for SNOE PCMs enhancement span in freezing and melting cycles was improved by 41 and 45.6 %, respectively. Similarly, cooling and melting times were reduced by 30.8 and 11.3 %, respectively. Embedded AgNP helps to achieve improved thermophysical and heat storage characteristics for SNOE PCMs, which in turn can be considered as a potential candidate for cool thermal energy storage applications.     

ASA/SEBS/paraffin composites as phase change material for potential cooling and heating applications in building

Phase change material (PCM) is able to melt and crystalize with a high heat of phase change at constant temperature, which provides new and green cooling and heating strategies for buildings. In this work, PCMs for buildings composed of acrylonitrile‐styrene‐acrylate copolymer (ASA), polystyrene‐b‐poly(ethylene/butylene)‐b‐polystyrene triblock copolymer (SEBS) and paraffin were fabricated by melt blending. The results of the accelerated leakage test indicated an excellent ability of PCMs to keep paraffin from leakage. Thermal properties suggested that the phase change enthalpy of PCMs increased with the increasing content of paraffin and their phase change temperature was close to the comfortable sensible temperature of human body, which made it quite suitable for building cooling and heating. Besides, PCMs presented excellent stability and reusability after several thermal cycling tests. The temperature test conducted with self‐designed cylindrical devices gave a more sufficient and direct demonstration of the cooling and heating effect. Remarkably, excellent cooling and heating performance (both as high as 15°C) of the composites could be obtained with the addition of paraffin. And the time span of the cooling and heating process was as long as 5 and 7.5 hours, respectively. Owing to its excellent cooling and heating capabilities, the ASA/SEBS/paraffin composites are of great potential to be applied in building temperature control.     

Effect of phase change materials on the hydration reaction and kinetic of PCM-mortars

The phase change materials are considered an attractive way to reduce energy consumption thanks to their heat storage capacity. Their incorporation in the construction materials allows the energy to be an integral part of the building structure. Even though PCMs have shown their reliability from a thermal point of view, some drawbacks linked to their use were emphasized such as the loss of the compressive strength of the PCM-material. This paper attempts to provide an explanation by the investigation of the hydration kinetic of PCM-mortars. The semi-adiabatic Langavant test was adapted to this case. The numerical diffuse element method was used for the computation of the heat flux, which is a compulsory step for the determination of the hydration degree. The results showed a lower heat released by the PCM mortars compared to a control mortar as well as a delay in the hydration progress with the addition of PCMs.     

相变蓄热材料研究进展

相变蓄热材料(恒温潜热热能储存材料)是目前最热门的功能材料之一。它在发生相变时储存、放出的热量能够帮助所在系统进行能量的储存,同时可以一定程度上缓解双方在时间、强度及地点上的不匹配程度。相变蓄热材料优点突出,其中包括在使用过程中自身温度变化较小、有很好的稳定性、储热能力较强等。此类材料对环境友好,响应了国家近年来节能环保的政策,同时也可以极大地优化所在系统的运行效率。本文综述了近年来几类相变蓄热材料的种类、特点及国内外学者应对于不同缺陷做出的改进及其应用于行业的研究现状,并对未来的发展进行了探讨与展望。     

Degradation of Fatty Acid Phase-Change Materials (PCM): New Approach for Its Characterization

The use of adequate thermal energy storage (TES) systems is an efficient way to achieve thermal comfort in buildings reducing the cooling and heating demand. Besides, deploy phase change materials (PCM) to meet and enhance the TES needs is highly effective and widely studied. In this paper, a study of the degradation of two fatty acids is presented, capric and myristic acids, in order to evaluate whether their thermo-physical properties are affected throughout time during service. This was carried out by means of two different types of thermal treatments: degradation at constant temperature (thermal stability test), 60 °C during 100 h and 500 h, and degradation with heating and cooling cycling (thermal cycling stability), between a temperature range from 15 °C to 70 °C with 0.5 °C/min ramp during 500 and 1000 cycles. Despite no significant changes were measured for myristic acid, experimental results revealed a decrease of melting enthalpy of 6.6% in capric acid thermally treated for 500 h. Evidences of chemical degradation were found that might explain the decrease in thermophysical properties during use.     

Study of effect of Al and Cu microparticles dispersed in D-Mannitol PCM for effective solar thermal energy storage

Journal of Thermal Analysis and Calorimetry - A practical use of phase change material (PCM)-based thermal energy storage (TES) system is effectively employed for mitigating the imbalance between...     

Evaluation of PCM/diatomite composites using exfoliated graphite nanoplatelets (xGnP) to improve thermal properties

This paper deals with the thermal performances of shape-stabilized phase change materials (SSPCM) for energy saving in various fields. This study enhanced thermal properties of SSPCM using exfoliated graphite nanoplatelets (xGnP). SSPCM, which contains the xGnP, was prepared by mixing and melting techniques for high dispersibility, thermal conductivity, and latent heat storage. In the experiment, we used hexadecane, octadecane, and paraffin as phase change materials (PCMs), and they have 254.7, 247.6, and 144.6 J g^?1 of latent heat capacity, and melting points of 20.84, 30.4, and 57.09 °C, respectively. The characteristics of SSPCMs were determined using SEM, DSC, FTIR, TG, TCi, and Energy simulation. SEM morphology showed homogenous dispersion of PCM and xGnP in the porous diatomite. DSC analysis results showed the latent heat capacity of SSPCM and SSPCM/xGnP composites, and TG analysis results showed the thermal reliability of the samples. Also, we checked the thermal conductivity of the SSPCM that contains xGnP, by TCi analysis.     

Numerical simulation and parametric analysis of latent heat thermal energy storage system

This paper presents the numerical analysis of the transient performance of the latent heat thermal energy storage unit established on finite difference method. The storage unit consists of a shell and tube arrangement with phase change material (PCM) filled in the shell space and the heat transfer fluid (HTF) flowing in the inner tube. The heat exchange between the HTF, wall and PCM has been investigated by developing a 2-D fully implicit numerical model for the storage module and solving the complete module as a conjugate problem using enthalpy transforming method. A comparative investigation of the total melting time of the PCM has been performed based on natural convection in liquid PCM during the charging process. The novelty of this paper lies in the fact it includes convection in PCM and this investigation includes a detailed parametric study which can be used as a reference to design latent heat storage. The results indicate that natural convection accelerates the melting process by a significant amount of time. In order to optimize the design of the thermal storage unit, parametric study has been accompanied to analyze the influence of various HTF working conditions and geometric dimensions on the total melting time of the PCM. Another important feature considered in this work is the influence of the inner wall of the tube carrying the HTF on the entire melting time of the PCM. An error of around 7.2% is reported when inner wall of the tube is ignored in the analysis.

     

Preparation and thermal properties of palmitic acid/polyaniline/copper nanowires form-stable phase change materials

Form-stable phase change materials (PCMs) with high thermal conductivity are essential for thermal energy storage systems, which in turn are indispensible in solar thermal energy applications and efficient use of energy. In this paper, a new palmitic acid (PA)/polyaniline (PANI) form-stable PCMs were prepared by surface polymerization. The highest loading of PA in the form-stable PCMs was 80 mass% with the phase change enthalpy (ΔH _melting) of 175 J g^?1. Copper nanowires (Cu NWs) were introduced to the form-stable PCM by mixing the Cu NWs with PA and ethanol prior to the emulsifying of PA in surfactant solution. The Cu NWs would remain intact in case the ethanol was eliminated before the PA/Cu NWs mixture was mixed with surfactant solution. Otherwise, the Cu NWs would be partially oxidized under the attack of ethanol and ammonium persulfate. The ΔH _melting of the form-stable PCMs containing Cu NWs decreased linearly with the increasing of Cu NWs loading. The ΔH _melting of the form-stable PCMs doped with 11.2 mass% Cu NWs was 149 J g^?1. The thermal conductivity of the form-stable PCMs could be effectively improved by Cu NWs. By adding 11.2 mass% Cu NWs, the thermal conductivity of the form-stable PCM could attain 0.455 W m^?1 K^?1.     

高结构稳定性、低泄漏率三维铜@石墨烯复合相变材料的制备

由于能源消费需求的持续增长和传统化学燃料的日益枯竭,对可再生能源的需求日益迫切。以地热能、太阳能为代表的可再生能源脱颖而出。然而,这些能源的应用易受到天气、季节、地点和时间的影响,具有不稳定性、随机性、波动性和间歇性。储能技术是解决上述问题的有效途径,它可以在需要的时候储存或释放能量。在各种储能技术可选材料中,相变材料(PCMs)是智能热能管理和便携式热能领域的有力候选者。大多数相变材料都存在导热系数低、环境污染、熔点泄漏等问题,因此有必要将相变材料封装到支撑骨架材料中。事实上,支撑材料在应用中仍面临着一些重大挑战。首先,骨架材料应能抵抗相变材料在相变过程中的体积变化,即具有良好的结构稳定性。其次,还应具有较高的导热系数和较低的泄漏率。石墨烯气凝胶(GA)已被证明是提高相变材料形状稳定性的有效支撑骨架,但相变引起的泄漏和网络结构的脆性是制约其应用的关键问题。在此,我们提出了一种双脉冲电镀的强化策略,用于制备铜@石墨烯气凝胶(Cu@GA)作为相变储能骨架材料。这一结构设计中,石墨烯气凝胶上的石墨烯片层上均匀地镀上了铜层,且不同片之间被铜镀层所连接。这种铜增强石墨烯气凝胶网络结构赋予复合材料良好的导热性和坚固的骨架稳定性,有利于增强相变换热和抑制相变过程中的泄漏。此外,通过真空浸渍法将十八胺(ODA)封装在Cu@GA骨架中,获得了结构稳定性高、泄漏率低的复合相变材料(Cu@GA/ODA),保证了ODA在Cu@GA骨架材料中的均匀分散和填充。通过比较复合相变材料的重量变化,研究了不同骨架对复合相变材料泄漏率的影响。优化后的复合相变材料(CPCM)Cu@GA/ODA经20次储热、放热循环后,泄漏率降低至19.82% (w,质量分数),而GA/ODA和GOA/ODA为骨架的复合相变材料的泄漏率分别为80.31% (w)和72.99% (w)。为了探讨这种影响的原因,用扫描电子显微镜(SEM)观察了循环后骨架的形貌。铜/石墨烯气凝胶(Cu@GA)骨架材料没有明显的收缩或坍塌,仍可以保持完整的三维网络结构,而氧化石墨烯气凝胶(GOA)和石墨烯气凝胶(GA)的骨架材料三维结构不复存在,且在氧化石墨烯/石墨烯片能够观察到明显的裂隙。铜涂层可以提高骨架的微观结构稳定性,有利于提高结构稳定性,降低复合材料的泄漏率。同时,该研究为构建理想的金属增强石墨烯气凝胶复合骨架材料铺平了新的道路,该复合材料具有优异的综合性能,可用于未来的相变储能、多孔微波吸收和储能应用。     

Thermo-physical characterization of some paraffins used as phase change materials for thermal energy storage

Three phase change paraffinic materials (PCMs) were thermophysically (phase-transition temperatures, latent heat, heat capacity at constant pressure, density, and thermal conductivity) investigated in order to be used as latent heat storage media in a pilot plant developed in Plovdiv Bulgaria. Raman structural investigation probes aliphatic character of the E53 sample, while the E46 and ECP samples contain also unsaturated components due to their Raman features within 1,500–1,700 cm^?1 range. Orthorhombic structure of the three PCMs was evidenced by the Raman modes at the 1,417 cm^?1. The highest latent heat value, ΔH, of phase transitions among the three materials was represented by summation of a solid order–disorder, and melting latent heat was encountered by the E53 paraffin, i.e., 194.32 J g^?1 during a μ-DSC scan of 1 °C min^?1. Conversely, the ECP composite containing ceresin component shows the lowest latent heat value of 143.89 J g^?1 and the highest thermal conductivity of 0.46 W m^?1 K^?1 among the three phase change materials (PCMs). More facile melt-disordered solid transition with the activation energy of 525.45 kJ mol^?1 than the lower temperature transition of disorder–order (E _a of 631.73 kJ mol^?1) during the two-step process of solidification for the E53 melt are discussed in terms of structural and molecular motion changes.     

Thermodynamic insights into n-alkanes phase change materials for thermal energy storage

n-Alkanes have been widely used as phase change materials (PCMs) for thermal energy storage applications because of their exceptional phase transition performance, high chemical stability, long term cyclic stability and non-toxicity. However, the thermodynamic properties, especially heat capacity, of n-alkanes have rarely been comprehensively investigated in a wide temperature range, which would be insufficient for design and utilization of n-alkanes-based thermal energy storage techniques. In this study, the thermal properties of n-alkanes (C₁₈H₃₈-C₂₂H₄₆), such as thermal stability, thermal conductivity, phase transition temperature and enthalpy were systematically studied by different thermal analysis and calorimetry methods, and compared with previous results. Thermodynamic property of these n-alkanes was studied in a wide temperature range from 1.9 K to 370 K using a combined relaxation (Physical Property Measurement System, PPMS), differential scanning and adiabatic calorimetry method, and the corresponding thermodynamic functions, such as entropy and enthalpy, were calculated based on the heat capacity curve fitting. Most importantly, the heat capacities and related thermodynamic functions of n-heneicosane and n-docosane were reported for the first time in this work, as far as we know. This research work would provide accurate and reliable thermodynamic properties for further study of n-alkanes-based PCMs for thermal energy storage applications.