Au core-PtAu alloy shell nanowires for formic acid electrolysis

Inefficient electrocatalysts and high-power consumption are two thorny problems for electrochemical hydrogen(H2)production from acidic water electrolysis.Herein we report the one-pot precise synthesis of ultrafine Au core-Pt Au alloy shell nanowires(Au@PtxAu UFNWs).Among them,Au@Pt_0.077 Au UFNWs exhibit the best performance for formic acid oxidation reaction(FAOR)and hydrogen evolution reaction(HER),which only require applied potentials of 0.29 V and-22.6 m V to achieve a current density of 10 m A cm^-2,respectively.The corresponding formic acid electrolyzer realizes the electrochemical H2 production at a voltage of only 0.51 V with 10 m A cm^-2 current density.Density functional theory(DFT)calculations reveal that the Au-riched Pt Au alloy structure can facilitates the direct oxidation pathway of FAOR and consequently elevates the FAOR activity of Au@Pt_0.077 Au UFNWs.This work provides meaningful insights into the electrochemical H₂ production from both the construction of advanced bifunctional electrocatalysts and the replacement of OER.     

Layered Ag-graphene films synthesized by Gamma ray irradiation for stable lithium metal ano des in carb on ate-based electrolytes

Lithium metal batteries are considered as high energy density battery systems with very promising prospects and have bee n widely studied.However,The uncon trollable plating/strippi ng behavior,infinite volume change and den drites formation of lithium metal anode restrict the applicati on.The unc on trolled n ucleati on of lithium caused by the non uniform multi-physical field distributions,can lead to the undesirable lithium deposition.Herein,a graphene composite uniformly loaded with Ag nano-particles(Ag NPs)is prepared through a facile Gamma ray irradiation method and assembled into self-supported film with layered structure(Ag-rGO film).Whe n such film is used as a lithium metal an ode host,the uncontrolled deposition is converted into a highly nucleation-induced process.On one hand,the Ag NPs distributed between the in terlayers of graphe ne can preferentially induce lithium nu cleati on and en able uniform deposition morphology of lithium between interlayers.On the other hand,the stable layered graphene structure can accommodate volume change,stabilize the interface between anode and electrolyte and inhibit dendrites formation.Therefore,the layered Ag-rGO film as anode host can reach a high Coulombic efficiency over 93.3% for 200 cycle(786 h)at a current density of 1 mA cm^-2 for 2 mAh cm^-2 in carbonate-based electrolyte.This work proposes a facile Gamma ray irradiation method to prepare metal/3D-skeleton structure as lithium anode host and demonstrates the potential to regulate the lithium metal deposition behaviors via manipulating the distribution of lithiophilic metal(e.g.Ag)in 3D frameworks.This may offer a practicable thinking for the subsequent design of the lithium metal anode.     

中国纤维素乙醇技术的研究进展

中国面临着严重的能源短缺和环境污染问题,中国政府正在局部几个省份内政策性鼓励燃料乙醇生产和使用.尽管当前主要是用玉米和谷物作为生产乙醇的原料,然而中国具有大量潜在的低成本的纤维素生物质原料,可以极大地扩大乙醇的产量,降低原料成本.近20年来,由于技术的革命性进步,已使得纤维素乙醇的生产成本从4美元/加仑以上,降低至约1.2-1.5美元/加仑.其中,每吨生物质约44美元.因此,目前乙醇掺汽油具有十分强的市场竞争力.已有几个公司正在建造首批商业纤维素乙醇工厂,虽然这些刚起步的小型设施在合理利用和管理上风险较小,但规模经济需要较大型工厂.尽管配送生物质原料的成本会随需求的增加而增加,但在乙醇生产基础上的生物精炼技术的发展,尤其是化工产品和动力的协同生产,将会使全过程的经济可行性大大提高.进一步深入的基础研究,将解决低成本下实现纤维素的完全利用,以确保在无政策性补贴的前提下,真正使纤维素乙醇成为具有市场竞争力的低成本纯液体燃料.     

Binary ligand strategy toward interweaved encapsulation-nanotubes structured electrocatalyst for proton exchange membrane fuel cell

Hierarchically porous architecture of ir on-nitroge n-carb on(Fe-N-C)for oxyge n reducti on reaction(ORR)is highly desired towards efficient mass transfer in the fuel cell device manner.Herein,we reported a binary ligand strategy to prepare zeolitic imidazolate frameworks(ZIFs)-derived precursors,wherein the addition of secondary ligand endows precursors with the capabilities to transform into porously interweaved encapsulation-nanotubes structured composites after calcination.The optimal catalyst,i.e.,termed as Fe₆-M/C-3,exhibits excellent durability with 88.8%current retention after 50,000 seconds in 0.1 M HClO₄solution by virtue of nanoparticles-encapsulation features,which is more positive than the benchmark commercial 20 wt%Pt/C catalyst.Moreover,a promising maximum power density of Fe₆-M/C-3 as cathode catalyst was also dem on strated in proton exchange membrane fuel cells(PEMFCs)measurements.Therefore,this binary ligand approach to the fabrication of hierarchically porous structures would also have significant implications for various other electrochemical reactions.     

Molten salt as ultrastrong polar solvent enables the most straightforward pyrolysis towards highly efficient and stable single-atom electrocatalyst

Currently,pyrolysis as the most widely used method still has some key issues not well resolved for synthesis of carbon-supported single-atom catalysts(C-SACs),e.g.,the sintering of metal atoms at high temperature as well as the high cost and complicated preparations of precursors.In this report,molten salts are demonstrated to be marvellous medium for preparation of C-SACs by pyrolysis of small molecular precursors(ionic liquid).The ultrastrong polarity on one hand establishes robust interaction with precursor and enables better carbonization,resulting in largely enhanced yield.On the other hand,the aggregation of metal atoms is effectively refrained while no nanoparticle or cluster is formed.By this strategy,a C-SAC with atomically dispersed Fe-N₄ sites and a high specific area over 2000 m² g^-1 is obtained,which illustrates high ORR activity in both acid and alkaline media.Moreover,this SAC exhibits superior methanol tolerance and stability after acid soaking at 85℃ for 48 h.It is believed that the molten-salts-assisted pyrolysis can be developed into a routine strategy as it not only can largely simply the synthesis of C-SACs,but also can be extended to prepare other types of SACs.     

镧对Mg-Si合金中Mg2Si相变质的影响

研究了Mg-5Si合金中La的添加对初生Mg2Si相变质的影响。结果表明,适量的La能够有效地变质初生Mg2Si相。基于本文的研究,在添加约0.5%La时,获得了最佳的变质效果,此时,初生Mg2Si相的尺寸减小到25μm以下,其形态从粗大的树枝形状变为多面体形状。然而,当La增加到0.8%或者更高时,初生Mg2Si相又生长为粗大的树枝形态。而且,在凝固过程中发现形成了一些LaSi2化合物,这些化合物的数量随着La的增加而呈现逐渐增加的趋势。     

电感耦合等离子体质谱法测定天然水体中19种元素

建立STD/KED模式-电感耦合等离子体质谱（ICP-MS）法同时测定天然水体中铍、硼、钛、钒、铬、锰、钴、镍、铜、锌、钼、镉、锑、钡、铊、铅、铁、砷和硒19种元素的分析方法。仪器调谐校准后,样品在线加入锂、钪、铑、铋校准溶液校正,以标准曲线内标法定量分析。标准曲线相关系数均大于0.999,样品加标回收率为92.6%～103.6%,质控样品测定值相对标准偏差为0.20%～2.6%(n=6),方法检出限为0.01～0.70μg/L。该方法灵敏度高,操作简便,节省人力,能满足天然水体中19种元素的同时检测需要。     

电解质-非电解质混合溶液活度系数的关联及溶解的推算 II:NH3-NaCl-Na2SO4-H2O体系的液固平衡热力学

由于在研究的体系中, Na2SO4是非对称电解质, 且能生成水合盐, 故推导了由非对称型电解质与非电解质所构成的混合溶液的各组分的活度系数关联通式, 并在此基础上讨论了水合盐液固平衡的计算方法.     

黄花棘豆化学成分的研究II:两种三萜皂苷的结构

从黄花棘豆的总皂苷中分离出两个新皂苷1和2.经光谱分析及化学方法确证,1为3-O-[α-L-鼠李吡喃糖基(1→2)-β-D-葡萄吡喃糖基(1→4)-β-D-葡萄吡喃糖醛酸基]-黄豆醇B;2为3-O-[α-L-鼠李吡喃糖基(1→2)-α-L-阿拉伯吡喃糖基(1→4)-β-D-葡萄吡喃糖醛酸基]-黄豆醇B.     

二氧化钛纳米管的研究进展

二氧化钛纳米管由于其新奇的光电、催化、气敏等性能引起了广泛的关注,在太阳能电池、光催化、环境净化、气体传感器等领域有潜在的应用价值.本文概述了近年来在制备方法、反应机理和组成、晶型和形貌及掺杂和应用方面的进展,并讨论了今后可能的研究发展方向.     

硅铝氧化物二元包覆钛白粉颗粒的有机改性

在二元包覆SiO₂,Al₂O₃薄膜的基础上,用钛酸酯偶联剂、硅烷偶联剂及三乙醇胺、季戊四醇对亚微米TiO₂颗粒表面进行有机改性.考察了改性条件对颗粒表面改性结果的影响.通过疏水性试验和润湿性试验对改性前后TiO₂颗粒的表面特性进行了表征.高温裂解色谱、热重分析、X光电子能谱的测试结果表明,不同改性剂与颗粒表面存在不同程度的化学键合作用.分析了改性剂在颗粒表面的包覆状态与结构.     

The adsorption and reaction of a titanate coupling reagent on the surfaces of different nanoparticles in supercritical CO2

The adsorption and reaction in supercritical CO2 of the titanate coupling reagent NDZ-201 on the surfaces of seven metal oxide particles, SiO2, Al2O3, ZrO2, TiO2 (anatase), TiO2 (rutile), Fe2O3, and Fe3O4, was investigated. FTIR and TG analysis indicated that the adsorption and reaction were different on different particle surfaces. On SiO2 and Al2O3 particles, there was a chemical reaction of the titanate coupling reagent on the surfaces. On the surfaces of ZrO2 and TiO2 (anatase) particles, there were two kinds of adsorption, weak and strong adsorption. On the surfaces of TiO2 (rutile), Fe2O3, and Fe3O4 particles, there was only weak adsorption. The acidity or basicity of the OH groups on the particle surface was the key factor that determined if a surface reaction occurred. When the OH groups were acidic, the titanate coupling reagent reacted with these, but otherwise, there was no reaction. The surface density of OH groups on the original particles and the amount of titanate coupling reagent adsorbed and reacted were estimated from TG analysis. The reactivity of the surface OH groups of Al2O3 particles was higher than that of the SiO2 particles.     

纳米氧化铕的表面改性及其在聚丙烯中的分散性能

以钛酸酯偶联剂在无水乙醇中对纳米氧化铕进行表面修饰,分别测定了处理好的样品的粒径及分布、在二氧六环中的沉降稳定性以及在聚丙烯中的分散性。结果表明:表面修饰有利于纳米氧化铕在聚丙烯中的分散,其中以10%钛酸酯处理的效果最佳;处理后样品的红外光谱表明,纳米氧化铕与偶联剂发生了化学键合作用,它们之间并不是简单的物理包覆。     

合成聚对苯二甲酸丙二醇酯负载型催化剂钛酸四丁酯/纳米二氧化硅的制备

以钛酸酯偶联剂(TMC-201)为改性剂,采用超声波分散方法对亲水性纳米二氧化硅(nano-SiO2)进行了表面改性。采用浸渍法将钛酯四丁酯(Ti(OC4H9)4)负载于表面改性的nano-SiO2上,制备了纳米级Ti(OC4H9)4/nano-SiO2负载型催化剂。考察了偶联剂用量、温度、时间对纳米SiO2表面改性的影响,研究了负载时间、负载温度和Ti(OC4H9)4用量对表面改性后纳米SiO2负载Ti(OC4H9)4的影响。结果表明,当TMC-201质量分数为35%、反应温度为90℃、反应时间为3.5 h时,纳米SiO2粒子表面接枝的偶联剂量最大;在室温下,负载48 h,Ti(OC4H9)4用量为表面改性纳米SiO2量的1/2时得到的Ti(OC4H9)4/nano-SiO2负载型催化剂负载Ti(OC4H9)4量最大;运用ICP-AES、FESEM等测试技术对修饰后的纳米SiO2及Ti(OC4H9)4/nano-SiO2负载型催化剂进行了表征;将Ti(OC4H9)4/nano-SiO2负载型催化剂用于聚对苯二甲酸丙二醇酯(PTT)聚酯合成的结果表明,与均相Ti(OC4H9)4催化剂相比,Ti(OC4H9)4/nano-SiO2负载型催化剂催化合成PTT聚酯过程中酯化时间177 min,与均相催化剂催化酯化时间相近,在缩聚2 h后得到PTT的特性粘度高达1.05,证明该负载型催化剂具有高的催化活性,既可催化酯化反应又可催化缩聚反应。     

Preparation and Properties of Nb-Coated Barium Titanate Composite Particles by Surface Modification with Nb Alkoxide in Hydrophobic Solvent

Chemical processing for the preparation of Nb-coated barium titanate composite particles was investigated using surface modification technology, hydrolyzing Nb ethoxide on the surface of barium titanate particles dispersed in hydrophobic solvent.It was confirmed from the measurements of specific surface area and zeta potential as well as SEM, TEM and EDX observations of the resulting composite particles that the original barium titanate particles were coated uniformly with hydrolysis product of Nb ethoxide.Barium titanates coated with 1 wt% of Nb as oxide were well sintered at 1200–1300°C. The dielectric constants of the sintered barium titanates showed flattened temperature dependence, but it depended upon the average particle size of original barium titanate. The sintered bodies of Nb-coated barium titanate powders with average particle size of 0.2 m gave dielectric constants of 2000–3000 and those of barium titanate with average particle size of 0.5 m showed dielectric constants of 3000–4000 at room temperature.The microstructure of the sintered barium titanate coated with Nb oxide consisted of grains of about 1 m, smaller than those of sintered original barium titanate.     

Surface modification of iron particles with a polyfluorinated disulfude: Effect of solvent and temperature

Adsorption of bis(2-chloro-3-oxaperfluorobutyl) disulfide from nonaqueous solutions onto the surface of carbonyl iron particles was studied with the aim of modification of these particles. The adsorption parameters were calculated using the Langmuir equation from the adsorption isotherms obtained in the interval 20-60°C. With an increase in temperature and in the solvent affinity for the modifying agent, the limiting amounts of the reagent that has interacted with the iron particle surface increase. This fact suggests the chemisorption nature of the process. The products of the reaction of iron with the disulfide can be desorbed from the particle surface.     

Controlled fluorination of clays

The fluorination of clays by a mild fluorinating reagent, HPF₆ was investigated using a sample of bentonite. The reaction resulted in the fluorination at the aluminum sites to form octahedral aluminum oxyfluoride species. This led to considerable modification of the surface characteristics such as surface area, porosity and particle size of nano-clay particles. The fluorinated clay was characterized by X-ray powder diffraction, XPS, SEM, EDS, infrared spectroscopy and solid-state NMR.     

磁性Fe3O4微粒表面有机改性

在分散聚合法制备复合磁性微球过程中,采用硅烷偶联剂KH 570对磁性Fe3O4微粒进行表面改性.红外光谱(FTIR)、光电子能谱(XPS)分析结果表明,偶联剂与磁性微粒表面以化学键形式结合.改性后,Fe3O4微粒与单体及其聚合物之间具有良好的亲和性,采用改性后的磁性微粒可以显著改善磁性微球的性能指标.     

磁性Fe_3O_4微粒表面有机改性

在分散聚合法制备复合磁性微球过程中 ,采用硅烷偶联剂 KH- 570对磁性 Fe_3O_4微粒进行表面改性 .红外光谱 (FTIR)、光电子能谱 (XPS)分析结果表明 ,偶联剂与磁性微粒表面以化学键形式结合 .改性后 ,Fe_3O_4微粒与单体及其聚合物之间具有良好的亲和性 ,采用改性后的磁性微粒可以显著改善磁性微球的性能指标 .     

Impact of titanate coupling agent on properties of high density polyethylene composite filled with coal gangue

In this study, surface modification of coal gangue (CG) was performed with titanate coupling agent 201 (isopropyl tri(dioctylpyrophosphate) titanate), and the effects of surface modifier on mechanical properties and thermal stability of high-density polyethylene filled with CG (HDPE/CG) and high-density polyethylene filled with modified CG (HDPE/mCG) composites were investigated. The coupling agent was successfully grafted on CG surface through chemical reaction according to the analyses of Fourier transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS), and the coupling agent can effectively enhance the hydrophobicity of surface that was verified by water contact angle beyond 90° of modified CG sample. With the introduction of coupling agent, some enhancements of tensile strength, flexural strength, and impact strength were observed in HDPE/mCG compared with HDPE/CG, due to the improved compatibility between mCG fillers and matrix. The increased storage modulus and decreased loss factor of HDPE/mCG composite further confirm the stronger interface adhesion after modification. Moreover, it is found that titanate coupling agent 201 can improve the thermal stability of HDPE/mCG composite to some extent.