Validation of <Superscript>239,240</Superscript>Pu, <Superscript>238</Superscript>Pu separation method using molecular recognition product AnaLig<Superscript>®</Superscript> Pu02 gel and extraction chromatography TRU<Superscript>®</Superscript> resin

Two separation techniques for plutonium determination using AnaLig^® Pu02 molecular recognition technology product (MRT) and extraction chromatography TRU^® resin were tested. The methods performance was investigated by analysis of National Physical Laboratory (NPL-Alpha-Beta High, ABH 2003, 2005) intercomparison test samples. The results obtained for both procedures were compared in terms of activities and recoveries. Data analysis showed good agreement with the reference values. The AnaLig^® Pu02 separation method for ^239,240Pu, ²³⁸Pu determination was successfully validated with the same performance as the TRU^® resin method.     

Invar<Superscript>®</Superscript> oxidation in CO<Subscript>2</Subscript>

In this article, corrosion of Invar^® in a static carbon dioxide atmosphere \( 2\times 1 0^{4} \le P_{{{\text{CO}}_{ 2} }} \le 10^{5} \,{\text{Pa}} \) has been studied between 1163 and 1263 K. At the beginning, after a short initial deceleration for weight gains Δm/S <0.5 mg cm^?2, oxidation kinetics were linear up to weight gains of about 4.0 mg cm^?2, and only wüstite Fe_1?x O was formed with a constant rate r (mg cm^?2 s^?1) \( r = \frac{{{\text{d}}\left( {\frac{\Updelta m}{S}} \right)}}{{{\text{d}}t}} = 0.41 \times P_{{{\text{CO}}_{ 2} }} \exp \left( {\frac{ - 198000}{RT}} \right) \) where R is the gas constant and t the time (s). Reaction mechanism is similar to that of the pure iron in analogous conditions, with the same rate limiting step i.e. external reaction of CO₂ with wüstite and outward diffusion of ions Fe²⁺ (not limiting). For weight gains Δm/S higher than 4 mg cm^?2, the limiting step changes, with an increase of the reaction rate and an internal oxidation. The origin of this mechanism change lies in the microcracks appearing in the oxide during its growth. Then, wüstite is no longer bound to the substrate; outward diffusion of ions Fe²⁺ stops and a topotactic transformation converts wüstite into magnetite.     

Characterization and application of SuperLig<Superscript>®</Superscript> 620 solid phase extraction resin for automated process monitoring of <Superscript>90</Superscript>Sr

Characterization of SuperLig^® 620 solid phase extraction resin was performed in order to develop an automated on-line process monitor for ⁹⁰Sr. The main focus was on strontium separation from barium, with the goal of developing an automated separation process for ⁹⁰Sr in high-level wastes. High-level waste contains significant ¹³⁷Cs activity, of which ^137mBa is of great concern as an interference to the quantification of strontium. In addition barium, yttrium and plutonium were studied as potential interferences to strontium uptake and detection. A number of complexants were studied in a series of batch K_d experiments, as SuperLig^® 620 was not previously known to elute strontium in typical mineral acids. The optimal separation was found using a 2 M nitric acid load solution with a strontium elution step of ~0.49 M ammonium citrate and a barium elution step of ~1.8 M ammonium citrate. ⁹⁰Sr quantification of Hanford high-level tank waste was performed on a sequential injection analysis microfluidics system coupled to a flow-cell detector. The results of the on-line procedure are compared to standard radiochemical techniques in this paper.     

<Superscript>13</Superscript>C-labeled bilirubin: synthesis of 3<Superscript>1</Superscript>(3<Superscript>2</Superscript>),17<Superscript>1</Superscript>(17<Superscript>2</Superscript>)-di-[<Superscript>13</Superscript>C]-mesobilirubin-XIIIα

Abstract  The title compound, labeled with ¹³C in the ethyl groups was synthesized from K¹³CN and low-molecular-weight components. The synthetic relay compound was 3¹(3²)[¹³C]-xanthobilirubinic acid methyl ester in a synthetic route that leads to a label in the ethyl β-substituent of a dipyrrinone model for bilirubin. This labeled dipyrrinone was oxidatively coupled to the dimethyl ester of mesobiliverdin-XIIIα, thereby providing a route to a ¹³C-labeled mesobiliverdin and mesobilirubin, with one carbon of each ethyl being 98% ¹³C-enriched. Graphical Abstract        

Identification of Anionic Supramolecular Complexes of Sulfonamide Receptors with Cl<Superscript>−</Superscript>, NO<Stack><Subscript>3</Subscript><Superscript>−</Superscript></Stack>, Br<Superscript>−</Superscript>, and I<Superscript>−</Superscript> by APCI-MS

As part of a mass spectrometric investigation of the binding properties of sulfonamide anion receptors, an atmospheric pressure chemical ionization mass spectrometric (APCI-MS) method involving direct infusion followed by thermal desorption was employed for identification of anionic supramolecular complexes in dichloromethane (CH₂Cl₂). Specifically, the dansylamide derivative of tris(2-aminoethyl)amine (tren) (1), the chiral 1,3-benzenesulfonamide derivatives of (1R,2S)-(+)-cis-1-amino-2-indanol (2), and (R)-(+)-bornylamine, (3), were shown to bind halide and nitrate ions in the presence of (n−Bu)₄N⁺X⁻ (X⁻ = Cl⁻, NO₃⁻, Br⁻, I⁻). Solutions of receptors and anions in CH₂Cl₂ were combined to form the anionic supramolecular complexes, which were subsequently introduced into the mass spectrometer via direct infusion followed by thermal desorption. The anionic supramolecular complexes [M+X]⁻, (M=1–3, X⁻=Cl⁻, NO₃⁻, Br⁻, I⁻) were observed in negative mode APCI-MS along with the deprotonated receptors [M−H]⁻. Full ionization energy of the APCI corona pin (4.5 kV) was necessary for obtaining mass spectra with the best signal-to-noise ratios.     

The selective separation of Pu isotopes using molecular recognition technology product AnaLig<Superscript>®</Superscript> Pu02 gel and extraction chromatography TRU<Superscript>®</Superscript> resin

Two separation techniques for plutonium determination using IBC^′S AnaLig^® Pu02 molecular recognition technology product (MRT) and extraction chromatography TRU^® resin (Eichrom ^®Industries) to effectively and selectively separate and recover plutonium were tested. The performance of the methods was successfully tested by analysis of NPL (High Alpha–Beta 2003, 2005) intercomparison sample and radioactive sludge sample from NPP A1 Jaslovské Bohunice with high activities of the plutonium radionuclides. The results obtained for both procedures were compared in terms of activities and recoveries.     

Relativistic coupled cluster calculations of the electronic structure of KrH<Superscript>+</Superscript>, XeH<Superscript>+</Superscript> and RnH<Superscript>+</Superscript>

Potential energy curves of NgH⁺ cations (Ng = Kr, Xe, Rn) were obtained by using four-component relativistic CCSD(T) coupled cluster calculations. Dissociation energies, equilibrium bond lengths, electronic properties, such as dipole moments and electric field gradients at the nuclei, and the related spectroscopic parameters of the electronic ground state have been determined. The results obtained for KrH⁺ and XeH⁺ are in good agreement with available experimental data, while those for RnH⁺ have been determined for the first time at this level of theory.     

Experimental Determination of the Isotherm at 15°C of the System Mg<Superscript>2+</Superscript>/Cl<Superscript>−</Superscript>, SO<Subscript>4</Subscript><Superscript>2</Superscript>–H<Subscript>2</Subscript>O

Summary.  The diagram of the ternary system Mg²⁺/Cl⁻, SO₄ ²⁻–H₂O was established at 15°C by means of analytical and conductimetric measurements. Three compounds were found in this diagram, which are MgSO₄·6H₂O, MgSO₄·7H₂O, and MgCl₂·6H₂O. The solubility field of MgSO₄·7H₂O is important whereas those of MgSO₄·6H₂O and MgCl₂·6H₂O are small. The compositions (mass-%) of the two invariant points determined by the two methods are: MgSO₄:MgCl₂=2.73:33.80 and MgSO₄: MgCl₂=3.38:28.91. Both the measured and the calculated isotherm at 15°C have been used for modelling of the diagram Mg²⁺/Cl⁻, SO₄ ²⁻–H₂O between 0 and 35°C. The polythermal invariant point was approximately located between 15 and 10°C.  Corresponding author. E-mail: ariguib@planet.tn Received October 16, 2002; accepted (revised) December 3, 2002 Published online April 24, 2003 RID="a" ID="a" Dedicated to Prof. Dr. Heinz Gamsj?ger on the occasion of his 70^th birthday     

Triboluminescence of zirconium η<Superscript>5</Superscript>-complexes

This work describes a comparative study of tribo- and photoluminescence of metallocenes (Cp₂HfCl₂, Cp₂TiCl₂, Cp₂ZrCl₂, (CpMe)₂ZrCl₂, rac-Me₂C(3-Bu^t-Cp)₂ZrCl₂, Ind*₂ZrCl₂). Occurring under mechanodestruction of polycrystals, triboluminescence of zirconium bis-cyclopentadienyl complexes, Cp₂ZrCl₂, (CpMe)₂ZrCl₂, and rac-Me₂C(3-Bu^t-Cp)₂ZrCl₂ has been revealed for the first time. The triboluminescence spectrum in air is similar to the photoluminescence spectrum of zirconocene polycrystals. The triboluminescence spectrum does not show *N₂ luminescence. Ne and Ar lines are observed in the triboluminescence spectrum in the atmosphere of these gases. An increase in the number of substituents in zirconocene ligands leads to a bathochromic shift of the emission band maximum in triboluminescence spectra of the complexes. Possible mechanisms of zirconocene triboluminescence excitation are discussed.     

The effect of NO<Stack><Subscript>3</Subscript><Superscript>−</Superscript></Stack> and OH<Superscript>−</Superscript> ions on the laser ablation of Cs<Superscript>+</Superscript> ion on Type 304 stainless steel

Type 304 stainless steel specimens artificially contaminated with CsCl solution were treated with KOH solution and KNO₃ solution, respectively. Cs⁺ ion removal tests by a Q-switched Nd:YAG laser at 1064 nm at a given fluence of 57.3 J/cm² were performed. The surface morphology and the relative atomic mole ratio of the specimen surface were investigated by SEM and EPMA. The order of Cs⁺ ion removal efficiency of laser was no-treatment < KOH < KNO₃ during the 42 shots. From the investigation of XPS peaks around 532.7 and 292.9 eV, KNO₃ on a surface of specimen was found to be fully decomposed during the laser irradiation. It was suggested that Cs₂O particulates formed by the reaction between the reactive oxygen generated from the nitrate ion and Cs⁺ ion on the metal surface could be easily suspended. For the KOH system, FeOOH was formed during the laser irradiation and it changed into Fe₂O₃. It was also suggested that Cs₂O particulates were formed by the reaction between the reactive oxygen generated from the decomposition of K₂O and Cs⁺ ion on the metal surface..     

Influence of ion size on the stability of chloroplumbates containing PbCl<Stack><Subscript>5</Subscript><Superscript>−</Superscript></Stack> or PbCl<Stack><Subscript>6</Subscript><Superscript>2−</Superscript></Stack>

The enthalpies of formation of PbCl₄, PbCl₅⁻ and PbCl₆²⁻, originating from quantum mechanics, have enabled the thermodynamic behaviour of these ions with respect to Cl-detachment to be assessed. The stability of salts containing PbCl₅⁻ and PbCl₆²⁻ as a function of the dimensions of these anions and complementary cations was studied using an approach combining the Kapustinskii-Yatsimirskii equation with basic thermochemical relationships. It was found that hexachloroplumbates of monovalent metal cations will not dissociate into metal chlorides and PbCl₄, provided the complementary cations are suitably large in size. Hexachloroplumbates of divalent metal cations have not yet been synthesised since no known metal cations attain the requisite large size. Such salts will not dissociate if the divalent metal cations are able to complex suitably large electron-donating ligands. The pentachloroplumbates of both monovalent and divalent metal cations are unstable, since no known metal cations have appropriately large ionic radii. The approach adopted appears to be useful for the examination of the thermal behaviour, stability and reactivity of chloroplumbates.     

Production possibility of <Superscript>186</Superscript>Re via the <Superscript>192</Superscript>Os(p,α3n)<Superscript>186</Superscript>Re nuclear reaction

Experimentally measured cross-sections are presented for the first time for the ¹⁹²Os(p,α3n)¹⁸⁶Re nuclear reaction up to 67 MeV. Highly enriched thin ¹⁹²Os targets (15 pcs), prepared by electro-deposition onto Cu backings, were irradiated with an external proton beam delivered by the SSC cyclotron of iThemba LABS. The excitation function curve of the ¹⁹²Os(p,α3n)¹⁸⁶Re reaction shows a maximum cross-section of ~82 mb at about 24 MeV. According to the yield calculations based on the present results, the available cumulative no-carrier-added ¹⁸⁶Re yield is 7.76 MBq/μAh (0.21 mCi/μAh) over the energy region 13.4 → 27.3 MeV.     

Cyclotron production of <Superscript>211</Superscript>At/<Superscript>211g</Superscript>Po by <Superscript>209</Superscript>Bi(α,2n) reaction

Astatine-211 (T _1/2 = 7.214 h) is an α-emitter at secular equilibrium by EC with its ultra-short-lived α-emitting daughter, polonium-211g (T _1/2 = 0.516 s), with a high Linear Energy Transfer (LET — 130 eV·nm⁻¹) and a half-life suitable for metabolic radiotherapy; the overall α branching of the ²¹¹At/^211gPo system is 100%. The direct production of ²⁰⁹Bi(α,2n)²¹¹At/^211gPo seems the most satisfactory method; Bi targets were irradiated at JRC-Ispra Cyclotron of European Commission, EC, using α-energy higher than 28.61 MeV in order to produce, via ²⁰⁹Bi(α,3n) reaction, small amounts of the γ-emitter ²¹⁰At (used as internal spike).     

A study of the hydrolysis of ZrF<Stack><Subscript>6</Subscript><Superscript>2−</Superscript></Stack> and the structure of intermediate hydrolysis products by <Superscript>19</Superscript>F and <Superscript>91</Superscript>Zr NMR in the 9.4 T field

The high-field ¹⁹F and ⁹¹Zr NMR method is used to study the hydrolysis and polycondensation of hexafluorozirconate ZrF₆²⁻ in aqueous and water-peroxide solutions. During hydrolysis in aqueous solutions only ZrF₆²⁻ and F⁻ ions were observed by NMR, however, in the water-peroxide medium, an intermediate product of hydrolysis ([F₅Zr-OO-ZrF₅]⁴⁻ dimer) was detected. The dimer structure is confirmed by ¹⁹F and ⁹¹Zr NMR. In high fields (¹⁹F NMR frequency > 200 MHz), the fluorine exchange between ZrF₆²⁻ and F⁻ is slow in the ¹⁹F NMR scale and has a multisite character.     

Isotope effects on band intensities in the <Emphasis Type="Italic">B</Emphasis><Superscript>2</Superscript>Σ<Superscript>+</Superscript>-<Emphasis Type="Italic">X</Emphasis><Superscript>2</Superscript>Σ<Superscript>+</Superscript> system of GaO isotopomers

Relative intensities of eight vibronic bands, belonging to the Δυ = −2 sequence of the B ²Σ⁺ −X ²Σ⁺ electronic transition of four GaO isotopomers have been measured and interpreted in terms of possible isotope effects on the parameters governing the band intensity. Obtained results showed very small isotope effect on the Franck-Condon factors and r-centroids and revealed that the observed intensity ratios of the corresponding isotope bands are controlled mainly by the isotope abundance of ⁶⁹Ga and ⁷¹Ga in natural gallium. The article is published in the original.     

A simple and quick method for the preparation of radionuclide <Superscript>87</Superscript>Y/<Superscript>87m</Superscript>Sr generator using the <Superscript>nat</Superscript>Rb(α,xn)<Superscript>87</Superscript>Y reaction

A rapid method for the preparation of ⁸⁷Y/^87mSr radionuclide generator from a rubidium chloride target irradiated with 35 MeV α-particles is described. A simple two-step procedure is used to obtain a carrier-free ^87mSr isotope with a high enough radiochemical yield and high purity in the final aqueous fraction.     

Preparation of <Superscript>235m</Superscript>U targets for <Superscript>235</Superscript>U(n,n′)<Superscript>235m</Superscript>U cross section measurements

This paper describes the preparation of samples for an experiment to measure the cross-section for ²³⁵U(n,n′)^235mU in a fast fission spectrum of neutrons provided by a fast pulsed reactor/critical assembly. Samples of ^235mU have been prepared for the calibration of the internal conversion electron detector that is used for the ^235mU measurement. Two methods are described for the preparation of ^235mU. The first method used a U-Pu chemical separation based on anion-exchange chromatography and the second method used an alpha recoil collection method. Thin, uniform samples of ^235mU+²³⁵U were prepared for the experiment using electrodeposition.     

Interactions between AuCl<Subscript>4</Subscript><Superscript>−</Superscript> and CTA<Superscript>+</Superscript> ions in water

The solubility of hexadecyltrimethylammonium tetrachloroaurate (CTA·AuCl₄) in water was measured at different temperatures of 288.2, 293.2, 298.2, 303.2, and 308.2 K. The enthalpy change associated with the formation of the CTA·AuCl₄ precipitate was estimated on the basis of the van’t Hoff equation and was found to be −42.5 ± 2.8 kJ mol⁻¹ at 298.2 K. The calorimetric enthalpy change for the CTA·AuCl₄ precipitate formation was directly determined by isothermal titration calorimetry performed at 298.2 K and was found to agree well with that estimated from the van’t Hoff equation.     

Isothermal solubility diagram of the 2Na<Superscript>+</Superscript>,Mg<Superscript>2+</Superscript>‖2Cl<Superscript>−</Superscript>, 2ClO<Stack><Subscript>3</Subscript><Superscript>‒</Superscript></Stack>-H<Subscript>2</Subscript>O quaternary system at 20 and 100°C

The solubility in the 2Na⁺,Mg²⁺‖2Cl⁻, 2ClO₃⁻-H₂O system was studied at 20 and 100°C and the solubility diagrams were plotted. New compounds were not found to form in the title quaternary reciprocal system. The sodium chloride field was observed to expand with rising temperature.