带羧基单分散彩色微球的制备

采用两步活性溶胀种子聚合法, 制备了可用于免疫检测的3种不同颜色的表面带有羧基功能基的粒径在400—800 nm之间的彩色单分散微球. 先用无皂乳液聚合法制备出单分散聚苯乙烯种子, 然后用邻苯二甲酸二正丁酯(DBP)作为溶胀剂对微球进行溶胀, 溶涨后的种子模板再用混溶的苯乙烯、二乙烯苯、丙烯酸、双键彩色染料以及引发剂(BPO)溶胀, 升温聚合后得到理想的单分散微球. 考察了DBP和单体用量、各单体配比及染料对微球的形貌和单分散性的影响.     

蒸发自组装法制备聚苯乙烯胶体晶体

采用乳液聚合法制得亚微米级聚苯乙烯单分散微球,并用蒸发自组装法在乳液气-液界面进行自上而下的层层组装,制得了厚度在450μm以上的三维有序胶体晶体。结果表明,影响胶体晶体有序性的关键因素是对蒸发速度的控制,促使胶体晶体规则排列的最主要作用力为溶液的毛细管力。在胶体晶体组装末期,随着溶剂量的减少,空间阻力逐渐增大,微球对流能力下降,造成胶体晶体的有序性降低。     

Pinched flow fractionation devices for detection of single nucleotide polymorphisms

We demonstrate a new and flexible microfluidic based method for genotyping single nucleotide polymorphisms (SNPs). The method relies on size separation of selectively hybridized polystyrene microspheres in a microfluidic pinched flow fractionation (PFF) device. The microfluidic PFF devices with 13 mum deep channels were fabricated by thermal nanoimprint lithography (NIL) in a thin film of cyclic-olefin copolymer (mr-I T85) on a silicon wafer substrate, and the channels were sealed by thermal polymer bonding. Streptavidin coated polystyrene microspheres with a mean diameter of 3.09 microm and 5.6 microm were functionalized with biotin-labeled oligonucleotides for the detection of a mutant (Mt) or wild-type (Wt) DNA sequence in the HBB gene, respectively. Hybridization to functionalized beads was performed with fluorescent targets comprising synthetic DNA oligonucleotides or amplified RNA, synthesized using human DNA samples from individuals with point mutations in the HBB gene. Following a stringent wash, the beads were separated in a PFF device and the fluorescent signal from the beads was analyzed. Patients being wildtypes, heterozygotes or mutated respectively for the investigated mutation could reliably be diagnosed in the PFF device. This indicates that the PFF technique can be used for accurate and fast genotyping of SNPs.     

分散聚合与水热处理相结合制备单分散聚苯乙烯微球的研究

将分散聚合与水热处理相结合,以聚乙烯醇为稳定剂,以乙醇和水为分散介质,三羟甲基丙烷三丙烯酸酯为交联剂,一步法成功制备得到不同粒径的单分散交联聚苯乙烯微球.以乙醇/水的比例为50/50的反应体系为基础,研究了聚乙烯醇类型和含量,有机相含量,引发剂浓度,以及水热釜填充量等对所制备的微球形貌的影响,发现聚乙烯醇类稳定剂的分子量的降低和含量的增多倾向于生成黏连的微球;在有交联剂的条件下,不含稳定剂的体系仍能够得到单分散的交联PS微球;有机相含量的增加会导致微球呈现多分散性;而体系中引发剂的含量和反应液在水热釜中的填充量对微球的形貌影响不大.进一步针对水热法的特点分析探讨了一步法成功制备单分散的交联聚苯乙烯微球的原因及其机理.     

Organized monolayer of thermosensitive microgel beads prepared by double-template polymerization

A 2D close-packed array of thermosensitive microgel beads was prepared by the double-template polymerization method. First, a 2D colloidal crystal of silica beads with 10 microm diameter was obtained by the solvent evaporation method. This monolayer of colloidal crystals can serve as the first template for the preparation of macroporous polystyrene. The macroporous polystyrene trapping the crystalline order can be used as a negative template for fabricating gel beads arrays. A functional surface using thermosensitive poly(N-isopropylacrylamide) gel beads array was fabricated by the double-template polymerization method.     

Preparation of Micron-size Functional Fluorescent Microspheres

As a kind of special functional microspheres, fluorescent polymer microspheres could be used in cell label and separation, blood flow assay, flow cytometer marking, chemical reaction assay,and in analyst of the transform and diffusion of particles in soil 1. However, one of the most important applications of fluorescent microspheres is in the high-throughput screening of drugs (HTS) 2. Through affinity interaction, radioactive ligands (latent drugs) are bound to fluorescent microspheres covered by receptor, and luminescence is produced by radioactivity, so ligands can be assayed and screened.In this study, we developed a technique for preparing micron-size fluorescent microspheres with different functional groups. The methods included the synthesis of micron-size polystyrene microspheres through the dispersion polymerization of styrene in different media such as ethanol,ethanol-water, and isopropanol; the functional polystyrene microspheres were prepared by introduction of functional monomers into the reaction system of styrene; the functional fluorescent microspheres were obtained by the way of dying functional microspheres in the fluorescent material's ethanol solvent.The average diameter of microspheres was in the range of 1～10 μm, and the distribution was normal distribution. The functional groups included -OH, -CHO, -COOH, -CONH2, and SO3H. The absorbing spectrum and exciting spectrum were tested, the results showed that the maximal absorbance of fluorescent microsphere was near 306.5 nm, and its maximal excitation was near 362 nm. The excitation spectrum of fluorescent material (DPO) and fluorescent microspheres were shown in figure 1, and it indicated that the developed fluorescent microspheres showed the same excitation behavior like DPO, which related to the fluorescent microspheres had stable luminescence property.     

Dye-labeled polystyrene latex microspheres prepared via a combined swelling-diffusion technique

A series of water-insoluble, biologically compatible dyes, meso-tetraphenylchlorin, meso-tetraphenylporphyrin and chlorophyll-a, were successfully incorporated into beads composed of linear polystyrene (PS) via a tunable combined swelling-diffusion process. Dyed PS beads were prepared by the addition of a dye solution in tetrahydrofuran to an aqueous suspension of 10 μm PS beads in the presence of a poly((ethylene glycol)-b-(propylene glycol)-b-(ethylene glycol)) block copolymer surfactant. The presence of surfactant was found to be beneficial to prevent particle aggregation, especially at tetrahydrofuran contents above 30%. Dye loading was shown to be tunable by simple adjustments in dye composition. Confocal fluorescence microscopy indicated that dyes were distributed uniformly throughout the entire PS bead, but heterogeneously with ~500 nm diameter droplets, indicative of a separate dye phase within the PS matrix. The stability of dyed beads, indicated by resistance to dye leaching in solvent, was found to be governed by the degree of swelling of PS in the solvent medium. Hence, no leaching was observed even when a good solvent for the dye was used (ethanol), as long as that solvent did not swell the carrier particle, PS. No leaching of dyes from the beads was observed during long-term (2 years) storage in water.     

Preparation of Monodispersed Polymer Microspheres by SPG Membrane Emulsification‐Solvent Evaporation Technology

The membrane emulsification coupled with solvent evaporation was adopted to prepare monodispersed polystyrene (PS) microspheres. Firstly, stable oil‐in‐water emulsion has been successfully obtained by pressing PS solution through SPG membrane into continuous phase at appropriate pressures. Then monodispersed PS microspheres with size of 2–20 µm were obtained following the removal of solvent. The size of the PS microspheres was strongly dependent on the mean pore size of SPG membrane and concentration of PS solution. Furthermore, the effect of emulsion stability, operation pressure and emulsifier on the size and size distribution of microspheres were systemically investigated. Finally, the surface character of PS microspheres was examined via SEM.     

Near-infrared aminocyanine dyes: synthesis,optical properties,and application to the preparation of fluorescent microspheres

Several near-infrared (NIR) fluorescent dyes based on aminocyanine have been designed, synthesized, and used for preparation of NIR fluorescent microspheres. Their spectral properties and pH-dependent optical characteristics were investigated. It was found that different substitution at the central position of the dyes led to diverse optical properties, with especially large effects on their spectroscopic properties. Spectroscopic responses of the fluorescent dyes to changes of pH were different. Under acidic conditions, the wavelengths of maximum absorption of the N-substituted cyanine dyes were clearly red shifted. Dyes with an N-substituted piperazidine ring were the most sensitive. The fluorescent microspheres retained the properties of the parent dyes, making them suitable for applications in biological studies.     

Influence of the seed polymer on the chromatographic properties of size monodisperse polymeric separation media prepared by a multi-step swelling and polymerization method

Monodisperse polymer particle-based separation media were prepared by a multi-step swelling and polymerization method with two pairs of monomers and two porogenic solvents. Their chromatographic properties were compared to those of beads prepared by a corresponding suspension polymerization method without the use of seed polymer to ascertain the influence of the seed polymer on their porous structures. A large change in porous structure was observed when the swollen particle consisting of monomers and porogenic solvents contained at least one good solvent for the polystyrene seed polymer, allowing it to remain in the polymerizing medium. In contrast, when the polystyrene seed particle was excluded from the swollen oil droplets, due to its poor solubility in the monomers and the porogenic solvents, there was no difference in the chromatographic properties such as pore volume, pore size, pore size distribution, or retention selectivity between the multi-step swelling and polymerization method and the suspension polymerization method. Since the only difference between the multi-step swelling and polymerization method and the suspension method is the use of the seed polymer, it appears that a very small amount (< 1% v/v) of seed polymers in the enlarged swollen droplets plays an important role as a porogen and affects the porous structure as well as the chromatographic properties of the monodisperse polymer particle-based separation media. © 1993 John Wiley & Sons, Inc.     

Pore size in one‐step swelling and polymerization of monodisperse polymer beads

Crosslinked polystyrene beads were prepared at low swelling ratios by one‐step swelling and polymerization method. Pore size of the beads was observed based on the GPC calibration curves. It is found that: (1) the pore size increases as the swelling ratio decreases; (2) when a good solvent is used as the porogen the pore size increases with the crosslinking monomer content; and (3) at high crosslinking monomer content the pore size does not depend on the porogen solubility. The effects are discussed in terms of polymer miscibility, including phase separation between the seed and bead polymers. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3270–3277, 2000     

Study of types and mixture ratio of organic solvent used to dissolve polymers for preparation of drug-containing PLGA microspheres

The effects of the types and the ratios of various organic solvents used as a mixtures to dissolve poly (lactide-co-glycolide) (PLGA) by using a solvent evaporation method, a technique used to prepare polymer particles, were carefully studied in order to investigate their advantages in developing drug delivery system (DDS) formulations for the prepared microspheres. The particle size and drug loading efficiency of drug-containing PLGA microspheres were found to be dependent on the types of solvent used due to the interfacial tension between the organic solvent and water phase. The drug loading efficiency of monodisperse microspheres prepared by using a membrane emulsification technique employing organic solvents and high interfacial tension for dissolving the PLGA was increased in a controlled manner. The organic solvents with high interfacial tension in the water phase used for the preparation of polymer particles by means of the solvent evaporation method were found to be suitable in terms of improvement in the properties of DDS formulations.     

High-throughput transformation of colloidal polymer spheres to discs simply via magnetic stirring of their dispersions

In this article, we have successfully demonstrated the high-throughput production of colloidal discs via magnetic stirring of aqueous dispersions of monodisperse, sulfate-stabilized polystyrene (PS) spheres in the presence of a good organic solvent. The organic solvent could be water-miscible, such as tetrahydrofuran, or water-immiscible, such as chloroform. Water-immiscible organic solvents were mixed into aqueous dispersions of PS spheres in the presence of sodium dodecyl sulfate. The geometry of the resulting discs could be easily adjusted by the magnetic stirring time and speed, the stirring bar weight, and the amount of organic solvent. Our strategy is simple, scalable, and hardly dependent on the nature of the organic solvent and the PS sphere diameter; PS spheres with diameters ranging from 200 nm to 5 μm were deformed into discs with almost 100% yield. When organic solutions of fluorescent dyes and nanoparticles were used instead of pure organic solvents for PS sphere liquefaction, fluorescent discs were obtained, underlining the effective, efficient encapsulation of the fluorescent substance in the discs.     

Preparation of porous polylactide microspheres by emulsion‐solvent evaporation based on solution induced phase separation

Porous polylactide (PLA) microspheres were fabricated by an emulsion‐solvent evaporation method based on solution induced phase separation. Scanning electron microscopy (SEM) observations confirmed the porous structure of the microspheres with good connectivity. The pore size was in the range of decade micrometers. Besides large cavities as similarly existed on non‐porous microspheres, small pores were found on surfaces of the porous microspheres. The apparent density of the porous microspheres was much smaller than that of non‐porous microspheres. Fabrication conditions such as stirring rate, good solvent/non‐solvent ratio, PLA concentration and dispersant (polyvinyl alcohol, PVA) concentration had an important influence on both the particle size and size distribution and the pore size within the microspheres. A larger pore size was achieved at a slower stirring rate, lower good solvent/non‐solvent ratio or lower PLA concentration due to longer coalescence time. Copyright © 2005 John Wiley & Sons, Ltd.     

Synthesis and characterization of spherical and hemispherical polyepoxide micrometer‐sized particles of narrow size distribution by a single‐step swelling of uniform polystyrene template microspheres with glycidyl methacrylate

Polystyrene template microspheres of narrow size distribution were prepared by dispersion polymerization of styrene in a mixture of ethanol and 2‐methoxy ethanol. Spherical and hemispherical polystyrene/poly(glycidyl methacrylate) microspheres of narrow size distribution were prepared by a single‐step swelling of the polystyrene template microspheres with the swelling solvent monomer glycidyl methacylate, followed by polymerization of the monomer within the swollen template microspheres at 73 °C. Uniform polystyrene/poly(glycidyl methacylate‐ethylene glycol dimethacrylate) polyepoxide composite microspheres were synthesized similarly, substituting glycidyl methacylate for glycidyl methacylate and ethylene glycol dimethacrylate. Uniform crosslinked poly(glycidyl methacylate‐ethylene glycol dimethacrylate) polyepoxide microspheres have been prepared by dissolution of the PS template polymer of the former composite microspheres. Particles with different properties, for example size, size distribution, shape, surface morphology, surface area, and so forth, were prepared by changing various parameters belonging to the swelling and/or polymerization steps, for example, volume of the swelling monomer/s and/or the swelling solvent dibutyl phthalate. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4612–4622, 2007     

葡萄球菌肠毒素B分子印迹聚合物的制备及其与蛋白质的结合性能

以葡萄球菌肠毒素B(SEB)蛋白为模板分子,以聚苯乙烯微球为基质,采用表面分子印迹法制备了SEB分子印迹聚合物.利用平衡吸附试验分析了SEB聚合物对目标蛋白的吸附能力及对类似底物的选择性;分析了该聚合物的吸附动力学,并利用扫描电镜观察了其形貌特征和颗粒尺寸.结果表明,经Scatchard模型分析求得的标题聚合物的最大表观结合量Qmax为3.23mg/g;所制备的SEB分子印迹聚合物呈微球形,粒径约为1²μm,对SEB蛋白具有较好的吸附性和特异选择性.     

Amphiphilic ESIPT benzoxazole derivatives as prospective fluorescent membrane probes

Fluorescent amphiphilic benzoxazole derivatives were synthesized and used to produce photoactive phosphatidylcholine (PC) liposomes by reserve-phase evaporation. The dyes absorbed in the UV region and were fluorescent in the blue-green region (determined by solvent polarity). The alkyl chain length seemed to play a fundamental role in the photophysics of the benzoxazole fluorophore in reverse liposomes, and despite the same ESIPT core and phospholipid building block, each amphiphilic dye had a particular emission profile related to the dye location in the liposome. The fluorescence emission spectra from dye 5 showed that its fluorophore experienced a polar environment, due to the single normal emission, while dyes 6–7 had (in part) a normal emission, and the main fluorescent band ascribed to the ESIPT emission indicated a more hydrophobic environment. Despite the complex fluorescent profiles, the benzoxazole derivatives could be successfully introduced into the reverse liposome structure due to the interaction between the alkyl chain and PC bilayer.     

Cross-linked starch nanoparticles stabilized Pickering emulsion polymerization of styrene in w/o/w system

Here, we present a method to synthesize expandable spherical polystyrene beads containing well-dispersed water microdroplets. The beads, 2–3 mm in diameter, were prepared through surfactant-free Pickering emulsion polymerization in water-in-oil-in-water (w/o/w) system using cross-linked starch nanoparticles (CSTN) as emulsifier. The CSTNs were in situ surface-modified by styrene maleic anhydride copolymer as confirmed by infrared spectroscopy and contact angle analysis. The entrapped water microdroplets with the average size of 3–4 μm were shown to be surrounded by a dense layer of the CSTN. The number droplet density as well as water encapsulation efficiency in the polystyrene beads increased with the CSTN concentration. Furthermore, regardless of CSTN content, all samples exhibited high encapsulation stability of over 68 % after 3 months. These characteristics along with good expansion behavior suggest the synthesized beads as expandable polystyrene containing water as a green blowing agent.     

In-situ encapsulation of quantum dots into polymer microspheres

We have incorporated fluorescent quantum dots (QDs) into polystyrene microspheres using functionalized oligomeric phosphine (OP) ligands. We find that a uniform distribution of quantum dots is loaded inside each polymer bead. Some local close-packing of quantum dots in the beads is attributed to the self-polymerization of the functionalized ligands. The presence of quantum dots disturbs the nucleation and growth processes during the formation of polymer microspheres and results in a wider size distribution of the quantum dot-embedded polystyrene beads than for the control without dots. The change in quantum efficiency of the quantum dots before (approximately 20%) and after (12%) loading into the beads substantiates the protection of oligomeric phosphine ligands yet indicates that the properties of these quantum dots are still affected during processing.     

纳米图案化高分子凝胶的制备

A new method was proposed to prepare binary composite colloidal crystal hydrogels by interlocking the as-prepared polystyrene/sulfonated polystyrene core/shell colloidal crystal hydrogel with a second responsive gel. The shell thickness thus the core size were synchronously controlled by altering the sulfonation time and temperature. The proper monomers were radically polymerized forming the second gel within the first gel network. The composition and structure were confirmed. Nanopatterued hydrogel including porous bulk hydrogels and surface patterned hydrogels were derived by properly treating the binary composite hydrogels. Specially, some typical patterns such as arrays of “nano-bowls” ,arrays of “nano-ribbons” and “nano-mask” were achieved by changing the treatment method such as by immersion in the solvent, after solvent evaporation from the sample surface during high rate rotation. This work provides a method to prepare nanopatterued hydrogels.