Poly(3,4‐ethylenedioxythiophene) (PEDOT)‐Coated MWCNTs Tethered to Conducting Substrates: Facile Electrochemistry and Enhanced Coloring Efficiency

Composite films of poly(3,4‐ethylenedioxythiophene) (PEDOT)‐coated over functionalized multiwalled coiled and linear carbon nanotubes (CNTs) have been fabricated by a simple oxidative electropolymerization route. The nanotubular morphology of the polymer–CNT composite is responsible for the lower charge transfer impedance, lower internal resistance, and superior capacitive response in comparison to that shown by the control PEDOT film doped by trifluoromethanesulfonate ions. This facile electrochemistry exhibited by the PEDOT–CNT composite film ensues in a remarkably high coloration efficiency of 367 cm² · C⁻¹ at 550 nm, hitherto unrealized for PEDOT; thus demonstrating the huge potential the PEDOT–CNT composite film has as cathode for the entire spectrum of electrochromic devices.

     

Binder Free Modification of Glassy Carbon Electrode by Employing Reduced Graphene Oxide/ZnO Composite for Voltammetric Determination of Certain Nitroaromatics

Reduced Graphene oxide/ZnO nanoflowers ( rGO/ZnO‐NFs ) composite has been synthesized in‐situ using asymmetric Zn complex ( 1 ) as a single‐source molecular precursor (SSMP) with GO at 150 °C. The rGO/ZnO‐NFs composite was characterized by PXRD, UV‐vis, SEM, EDX mapping, TEM and SAED pattern to confirm its purity and morphology. The rGO/ZnO‐NFs composite shows uniform distribution of nanoflowers on graphene sheets. The modified glassy carbon electrode ( GCE ) was fabricated by drop wise layering of the rGO/ZnO‐NFs composite at the surface of the GCE without using binder. The binder free modified electrode ( GCE‐rGO/ZnO ) was explored for detection of nitroaromatics such as p‐nitro‐phenol ( p ‐NP ), 2,4‐dinitrophenol ( 2,4‐DNP ), 2,4‐dinitrotoluene ( 2,4‐DNT ) and 2,4,6‐trinitrophenol ( 2,4,6‐TNP ). The fabricated sensor showed remarkable response for the both toxicants and explosives. The LOD, sensitivity and linear range for the studied toxicants and explosives were found to be in a good range: p ‐NP= 0.93 μM, 240 μA mM⁻¹ cm⁻² and 0.2–0.9 mM; 2,4‐DNP= 6.2 μM, 203 μA mM⁻¹ cm⁻² and 0.1–0.9 mM; 2,4‐DNT= 10 μM, 371 μA mM⁻¹ cm⁻² and 0.2–0.9 mM; 2,4,6‐TNP= 16 μM, 514 μA mM⁻¹ cm⁻² and 0.2–0.9 mM, respectively.     

Achieving high electrode specific capacitance with materials of low mass specific capacitance: Potentiostatically grown thick micro-nanoporous PEDOT films

Electrode materials for supercapacitors are at present commonly evaluated and selected by their mass specific capacitance (C_M, F g⁻¹). However, using only this parameter may be a misleading practice because the electrode capacitance also depends on kinetics, and may not increase simply by increasing material mass. It is therefore important to complement C_M by the practically accessible electrode specific capacitance (C_E, F cm⁻²) in material selection. Poly[3,4-ethylene-dioxythiophene] (PEDOT) has a mass specific capacitance lower than other common conducting polymers, e.g. polyaniline. However, as demonstrated in this communication, this polymer can be potentiostatically grown to very thick films (up to 0.5 mm) that were porous at both micro- and nanometer scales. Measured by both cyclic voltammetry and electrochemical impedance spectrometry, these thick PEDOT films exhibited electrode specific capacitance (C_E, F cm⁻²) increasing linearly with the film deposition charge, approaching 5 F cm⁻², which is currently the highest amongst all reported materials.     

High‐performance Flexible Complementary Electrochromic Device Based on Plasma Modified WO3 Nano Hybrids and V2O5 Nanofilm with Low Operation Voltages

Tungsten trioxide‐poly(3,4‐ethylenedioxythiophene) (WO₃‐PEDOT) and tungsten trioxide‐polyfuran (WO₃‐PFu) were prepared by rf rotating plasma polymerization. Electrochromic hybrid thin films were fabricated onto flexible polyethylene terephthalate (PET)/ indium tin oxide (ITO) film using electron beam evaporation method. In order to deeply characterize all films, scanning electron microscopy‐energy dispersive X‐ray spectroscopy (SEM‐EDS) and electrochemical impedance spectroscopy (EIS) techniques were used. The counter electrode effect on plasma modified WO₃ nano hybrids‐based electrochromic devices (ECDs) was evaluated. By incorporating flexible vanadium pentoxide (V₂O₅) film as counter electrode, complementary ECDs were constructed through combining the hybrid flexible films (WO₃‐PEDOT, WO₃‐PFu) as working electrodes, which exhibit highly efficient electrochromic performance with low voltage operation. Especially, WO₃‐PEDOT/V₂O₅‐based ECD owns a high optical modulation of 61.5 % at 750 nm driven by −1.0 V (coloration) and +1 V (bleaching) with fast response times (coloration time: 13.58 s, bleaching time: 8.07 s) and a high coloration efficiency of 527 cm² C⁻¹. This study can supply useful and efficient avenue for designing flexible complementary electrochromic device for energy‐saving flexible electronics.     

Assessment of corrosion protection and performance of bio-based polyurethane acrylate incorporated with nano zinc oxide coating

In this study, a series of UV-curable anticorrosive PUA coatings embedded with varying concentrations of inorganic ZnO fillers have been successfully prepared from jatropha-based polyol. The electrochemical impedance spectroscopy (EIS) and Tafel polarisation analysis revealed that increasing fillers composition lead to the improvement of the anticorrosive property of the hybrid coatings. Meanwhile, the salt spray test results were found to correlate with the EIS of C_c (F cm⁻²) was 2.71 × 10⁻⁹, Bode plot - 10⁶ Ω cm² and Tafel polarisation results 7.56 × 10⁻⁶ MPY at 3 wt% of ZnO. Physical properties of 3 wt% loading of ZnO fillers in hardness test obtained 6H which was strongly attributed to the low interfacial interaction and poor dispersion of the fillers within the polymer matrix.     

One-step fabrication of chitosan–hematite nanotubes composite film and its biosensing for hydrogen peroxide

This work reports on a novel chitosan–hematite nanotubes composite film on a gold foil by a simple one-step electrodeposition method. The hybrid chitosan–hematite nanotubes (Chi–HeNTs) film exhibits strong electrocatalytic reduction activity for H₂O₂. Interestingly, two electrocatalytic reduction peaks are observed at −0.24 and −0.56 V (vs SCE), respectively, one controlled by surface wave and the other controlled by diffusion process. The Chi–HeNTs/Au electrode shows a linear response to H₂O₂ concentration ranging from 1 × 10⁻⁶ to 1.6 × 10⁻⁵ mol L⁻¹ with a detection limit of 5 × 10⁻⁸ mol L⁻¹ and a sensitivity as high as 1859 μA μM⁻¹ cm⁻².     

Highly Sensitive Nitric Oxide Sensing Using Three‐Dimensional Graphene/Ionic Liquid Nanocomposite

A nanocomposite gel with a uniform porous structure and well‐controlled compositions prepared by mixing three‐dimensional graphene material with an ionic liquid, 1‐butyl‐3‐methylimidazolium hexafluorophosphate, is used for nitric oxide detection. It shows a fast response of less than 4 seconds, an excellent sensitivity of 11.2 µA cm⁻² (µmol/L)⁻¹ and an extremely low detection limit of 16 nM with a signal‐to‐noise ratio of 3 (S/N=3), a performance superior to that of reported works based on carbon nanotubes and nanoparticles. The high sensitivity is attributed to the large electroactive surface area of the graphene gel nanocomposite towards nitric oxide oxidation. The electrochemical behavior of the gel nanocomposite is investigated and explained.     

Effect of 120 MeV Au9+ ion irradiation on the structure and surface morphology of ZnO/NiO heterojunction

ZnO/NiO thin films, each of thickness 100 nm, were deposited on Si(100) substrate by pulsed laser deposition method. The resulting heterojunction, ZnO/NiO/Si, was irradiated by 120 MeV Au⁹⁺ ions and characterized by grazing incidence X‐ray diffraction (GIXRD), Raman spectroscopy, and atomic force microscopy (AFM). The GIXRD confirmed the presence of both NiO and ZnO in the samples. Ion irradiation induced suppression of crystalline nature, and the recrystallization of the same occurred at the fluence of 1 × 10¹³ ions cm⁻². The occurrence of most intense band at 302 cm⁻¹ in Raman spectra corresponds to the symmetric stretching vibration of ZnO. The linear shift of stretching mode of ZnO with ion fluence could be associated with the effect of compressive stress in the material. AFM analysis of the films indicated that the rms roughness increased when the film is irradiated at a fluence of 1 × 10¹² ions cm⁻². Beyond this fluence, the value of roughness decreased up to fluence of 1 × 10¹³ ions cm⁻² and increased thereafter. To see the effect of the stress of buffer layer on the surface layer, we calculated the stress for NiO layer with ion fluence form the lattice parameter. Comparing the stress of buffer layer with roughness of surface layer at the given fluence, we can say that the compressive stress in the buffer layer could possibly control the roughness of the surface layer.     

A 3D Hydroxylated MXene/Carbon Nanotubes Composite as a Scaffold for Dendrite-Free Sodium-Metal Electrodes

Sodium metal is a promising anode, but uneven Na deposition with a dendrite growth seriously impedes its application. Herein, a fibrous hydroxylated MXene/carbon nanotubes (h-Ti₃C₂/CNTs) composite is designed as a scaffold for dendrite-free Na metal electrodes. This composite displays fast Na⁺/electron transport kinetics and good thermal conductivity and mechanical properties. The h-Ti₃C₂ contains abundant sodiophilic functional groups, which play a significant role in inducing homogeneous nucleation of Na. Meanwhile, CNTs provide high tensile strength and ease of film-forming. As a result, h-Ti₃C₂/CNTs exhibit a high average Coulombic efficiency of 99.2 % and no dendrite after 1000 cycles. The h-Ti₃C₂/CNTs/Na based symmetric cells show a long lifespan over 4000 h at 1.0 mA cm⁻² with a capacity of 1.0 mAh cm⁻². Furthermore, Na-O₂ batteries with a h-Ti₃C₂/CNTs/Na anode exhibit a low potential gap of 0.11 V after an initial 70 cycles.     

Metal-like Charge Transport in PEDOT(OH) Films by Post-processing Side Chain Removal from a Soluble Precursor Polymer

Herein, a route to produce highly electrically conductive doped hydroxymethyl functionalized poly(3,4-ethylenedioxythiophene) (PEDOT) films, termed PEDOT(OH) with metal-like charge transport properties using a fully solution processable precursor polymer is reported. This is achieved via an ester-functionalized PEDOT derivative [PEDOT(EHE)] that is soluble in a range of solvents with excellent film-forming ability. PEDOT(EHE) demonstrates moderate electrical conductivities of 20–60 S cm⁻¹ and hopping-like (i.e., thermally activated) transport when doped with ferric tosylate (FeTos₃). Upon basic hydrolysis of PEDOT(EHE) films, the electrically insulative side chains are cleaved and washed from the polymer film, leaving a densified film of PEDOT(OH). These films, when optimally doped, reach electrical conductivities of ≈1200 S cm⁻¹ and demonstrate metal-like (i.e., thermally deactivated and band-like) transport properties and high stability at comparable doping levels.     

Selective Electroanalysis of Ascorbic Acid Using a Nickel Hexacyanoferrate and Poly(3,4‐ethylenedioxythiophene) Hybrid Film Modified Electrode

The mixed‐valent nickel hexacyanoferrate (NiHCF) and poly(3,4‐ethylenedioxythiophene) (PEDOT) hybrid film (NiHCF‐PEDOT) was prepared on a glassy carbon electrode (GCE) by multiple scan cyclic voltammetry. The films were characterized using atomic force microscopy, field emission scanning electron microscopy, energy dispersive spectroscopy, X‐ray diffraction, and electrochemical impedance spectroscopy (AC impedance). The advantages of these films were demonstrated for the detection of ascorbic acid (AA) using cyclic voltammetry and amperometric techniques. The electrocatalytic oxidation of AA at different electrode surfaces, such as the bare GCE, the NiHCF/GCE, and the NiHCF‐PEDOT/GCE modified electrodes, was determined in phosphate buffer solution (pH 7). The AA electrochemical sensor exhibited a linear response from 5×10⁻⁶ to 1.5×10⁻⁴ M (R²=0.9973) and from 1.55×10⁻⁴ to 3×10⁻⁴ M (R²=0.9983), detection limit=1×10⁻⁶ M, with a fast response time (3 s) for AA determination. In addition, the NiHCF‐PEDOT/GCE was advantageous in terms of its simple preparation, specificity, stability and reproducibility.     

Ionic electro-active polymer actuator based on cobalt-containing nitrogen-doped carbon/conducting polymer soft electrode

Nanoscale cobalt-containing nitrogen-doped porous carbon (CoNC) materials were prepared by thermolysis of a zeolitic imidazolate framework (ZIF), ZIF-67, at different temperatures and their application for ionic electro-active polymer (EAP) actuator was evaluated. CoNC-700, which was obtained from ZIF-67 pyrolysis at 700 °C, exhibits specific surface area of 753.86 m² g⁻¹, pore volume of 0.5768 cm³ g⁻¹, and specific capacitance of 120.7 F∙g⁻¹. CoNC/conducting polymer soft electrode were fabricated by unitizing effective interaction of CoNC with poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS). High-performance ionic actuators were developed for the first time using this CoNC/PEDOT:PSS soft electrode. The developed ionic EAP actuator exhibited large peak-to-peak displacement of 20.4 mm and high bending strain of 0.28% (3 V and 0.1 Hz). Therefore, ZIFs or metal organic frameworks (MOFs) can be applied to provide significant improvements in EAP actuators, which can play key roles as technological advances toward bioinspired actuating devices required for next-generation soft and wearable electronics.     

Modification of glassy carbon electrode with a polymer/mediator composite and its application for the electrochemical detection of iodate

A modified glassy carbon electrode was prepared by depositing a composite of polymer and mediator on a glassy carbon electrode (GCE). The mediator, flavin adenine dinucleotide (FAD) and the polymer, poly(3,4-ethylenedioxythiophene) (PEDOT) were electrochemically deposited as a composite on the GCE by applying cyclic voltammetry (CV). This modified electrode is hereafter designated as GCE/PEDOT/FAD. FAD was found to significantly enhance the growth of PEDOT. Electrochemical quartz crystal microbalance (EQCM) analysis was performed to study the mass changes in the electrode during the electrodeposition of PEDOT, with and without the addition of FAD. The optimal cycle number for preparing the modified electrode was determined to be 9, and the corresponding surface coverage of FAD (Γ_FAD) was ca. 5.11 × 10⁻¹⁰ mol cm⁻². The amperometric detection of iodate was performed in a 100 mM buffer solution (pH 1.5). The GCE/PEDOT/FAD showed a sensitivity of 0.78 μA μM⁻¹ cm⁻², a linear range of 4–140 μM, and a limit of detection of 0.16 μM for iodate. The interference effects of 250-fold Na⁺, Mg²⁺, Ca²⁺, Zn²⁺, Fe²⁺, Cl⁻, NO₃⁻, I⁻, SO₄²⁻ and SO₃²⁻, with reference to the concentration of iodate were negligible. The long-term stability of GCE/PEDOT/FAD was also investigated. The GCE/PEDOT/FAD electrode retained 82% of its initial amperometric response to iodate after 7 days. The GCE/PEDOT/FAD was also applied to determine iodate in a commercial salt.     

Seed layer-free electrodeposition and characterization of vertically aligned ZnO nanorod array film

Vertically aligned arrays of ZnO nanorod (ZNR) were rapidly synthesized on ITO glass without needing a pre-prepared seed layer of ZnO via a hexamethylenetetramine (HMT)-assisted electrodeposition route. The effect of HMT on the ZNR electrodeposition process was investigated by the cyclic voltammetric curve and the current–time curve. An electrodeposition growth model based on the capping effect of HMT–4H was proposed. The as-synthesized ZNRs possess single crystalline, a wurtzite crystal structure with markedly preferential growth orientation along [0001] direction determined by transmission electron microscopy and powder X-ray diffraction. As compared with the electrodeposited ZnO film without HMT assistance, the ZNR arrays showed the high transmittance (90%) in the visible wavelength range and the blue-shift of the band gap energy. Moreover, the presence of an optical-phonon E₂ (high) at 437.3 cm^?1 in Raman spectrum and strong ultraviolet emission at 376 nm but weak defect-related deep level emission in the room temperature photoluminescence spectrum also indicated that such ZNR arrays are of good crystal quality. More importantly, the rapid synthesis of ZNRs could provide the feasibility for preparation of ZnO nanotubes within a shorter time by a subsequent electrochemical dissolution process.     

Electrochemical behavior of the C60–γ-cyclodextrin inclusion complex (1:1) on HMDE in an aqueous solution

The electrochemical behavior of the water-soluble C₆₀–γ-CD (1:1) inclusion complex has been studied on the hanging mercury drop electrode. A one-electron reversible adsorptive electroreduction and three irreversible adsorptive electroreductions were detected by cyclic voltammetry. The amount of C₆₀–γ-CD adsorbed at saturation is 1.73 × 10⁻¹¹ mol/cm², the diffusion coefficient is 5.81 × 10⁻⁶ cm²/s, and the standard rate constant of the surface reaction k_s are 0.888 s⁻¹, 0.853 s⁻¹ and 1.032 s⁻¹, respectively.     

ZnO and TiO2 clusters as catalyst in the addition and abstraction reaction of acrylic acid with the OH radical

The present work displays the theoretical analysis on the role of metal oxide clusters as an effective catalyst in the reaction between acrylic acid and OH radical, which has an energy barrier of 12.4 kcal/mol. The formation of metal oxide cluster such as ZnO and TiO₂ with varying size from monomer to hexamer is analyzed using cohesive energy, which increases with cluster size. Adsorption of acrylic acid on clusters reveals that dimer ZnO and tetramer TiO₂ are good adsorbed entities. The dimer ZnO and tetramer TiO₂ clusters have reduced the barrier height. However, from the thermodynamical analysis of H-abstraction and OH addition reaction, the dimer ZnO cluster is found to be a good catalyst than a tetramer TiO₂ cluster. The favorable H abstraction and OH addition reactions are feasible at the active methylene group (–CH). OH addition reactions dominate over the H abstraction reaction. Further, the presence of metal oxide clusters enhances the rate of the reaction between acrylic acid and OH radical. The kinetics of the favorable reaction with a dimer ZnO cluster has a rate constant of 7.80 × 10⁻¹¹ cm³ molecule⁻¹ s⁻¹, which is higher than the literature report (1.75 × 10⁻¹¹ cm³ molecule⁻¹ s⁻¹). Overall, ZnO and TiO₂ metal oxide clusters can be effectively utilized as catalyst.     

Poly(3,4-ethylenedioxithiophene)/MnO2 composite electrodes for electrochemical capacitors

Composite electrodes of poly(3,4-ethylenedioxithiophene) and manganese oxide (PEDOT/MnO₂) have been prepared by electrodeposition of manganese oxide over PEDOT-modified titanium substrate. The PEDOT layers are deposited on titanium by potentiostatic deposition at 1.4 V and at two different temperatures: 5 and 25 °C (named PEDOT₍₅₎ and PEDOT₍₂₅₎, respectively). The electrodes are characterized by field emission gun scanning electron microscopy (FEG-SEM) and their electrochemical performances are evaluated by using cyclic voltammetry (CV) in 1 molL⁻¹ Na₂SO₄. The results show an improvement in the specific capacitance (C_s) of the oxide due to the presence of the polymer layer. Considering only the MnO₂ mass, the C_s values of the electrodes Ti/MnO₂, Ti/PEDOT₍₅₎/MnO₂ and Ti/PEDOT₍₂₅₎/MnO₂, estimated by the CV technique, are 151, 159 and 199 Fg⁻¹ at 10 mVs⁻¹ respectively. The micrographies of electrodes show that the polymer layer leads to very significant changes in the morphology of the oxide layers, which in turn generates the improvement observed in the capacitive property.     

Stable ZnO/ionic liquid hybrid materials: novel dual-responsive superhydrophobic layers to light and anions

Novel dual-responsive superhydrophobic hybrid materials,ZnO/SAMs(self-assembled monolayers)of ionic liquids(ILs)with different counter-anions(I-,BF4-,PF6-and Tf2N-),were synthesized and characterized.ZnO nanoparticles were first deposited on glass surfaces to produce roughness.Next,SAMs of fluorinated-alkyl-3-(3-triethoxysilylpropyl)-4,5-dihydro-imidazoliumiodide(abb.[C8Ftespim]I)were grafted onto these surfaces via-Si-O-covalent bonds using self-assembly technique.The Iion could be subsequently exchanged with BF4-,PF6-or Tf2N-through a simple aqueous anion-exchange reaction.The ZnO/ILs hybrid layers were characterized by atomic-force microscopy(AFM),scanning-electron microscopy(SEM)and X-ray photoelectron spectroscopy(XPS).Their wettability was estimated through the measurements of static and dynamic contact angles(CAs).Compared to corresponding films of ZnO/[C8Ftespim]I with CAs 140.7°±2.0°,films of ZnO/[C8Ftespim]PF6 and ZnO/[C8Ftespim]Tf2N showed CAs with 154.0°±2.0°and 152.0°±2.0°,respectively that remained for a long time.This result suggests that anion-exchange can afford superhydrophobic materials.In addition,the wettability of ZnO/[C8Ftespim]X hybrid layers can be reversibly switched by altering ultraviolet(UV)irradiation and dark storage,which shows a photo-induced reversible switch of wettability.The synergistic action of ZnO nanoparticles and SAMs of ILs produced light-anion dual-responsive superhydrophobic materials with ideal stability.     

Self-assembly of bilayer lipid membrane at multiwalled carbon nanotubes towards the development of photo-switched functional device

Bilayer lipid membrane (BLM) was self-assembled on a uniquely fabricated hydrophilic surface, containing N atoms from the carbon source of ethylene amine, of the multi-walled carbon nanotubes (MWNTs) to form the BLM/MWNTs nanocomposites. Cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and photoelectric experiments were taken to study the properties of the BLM/MWNTs nanocomposites. The thickness of the BLM, which was calculated from the CV data obtained at BLM/MWNTs electrode, turned out to be 4.38 nm, suggesting that the lipid self-assembled at the nanotubes surface was consistent with a bilayer structure. C₆₀-incorporated BLM could also be self-assembled at the nanotubes surface (C₆₀-BLM/MWNTs). The formation of BLM on the MWNTs surface blocked the diffusion of [Fe(CN)₆]^3/4− redox ions across BLM to the MWNTs electrode as no redox current was observed by CV measurement, whereas the incorporation of the electron mediator, C_60, resumed a pair of redox peaks at C₆₀-BLMs/MWNTs electrode. Moreover, the incorporation of C₆₀ led to a four order of magnitude reduction of the resistance of C₆₀-BLM/MWNTs (369.3 Ω) than that of BLM/MWNTs (3.238 × 10⁶ Ω). MWNTs electrode exhibited an intrinsic cathodic photocurrent (166 μA cm⁻²) while BLM/MWNTs electrode blocked photocurrent response of the MWNTs. Interestingly, C₆₀-BLM/MWNTs electrode resumed partial photoelectric properties (photo current: 65 μA cm⁻²) due to the electron mediation effect of C₆₀ incorporated into the lipid membrane. As a result, the novel self-assembled BLM/MWNTs nanocomposites provided a simple yet useful model to study the C₆₀-mediated photoelectric properties of the BLM/MWNTs which may be applicable to develop new biosensors and molecular devices.