电感耦合等离子体质谱法快速测定苦荞茶中铜、铅、镉、钴、镍

建立了用硝酸-高氯酸消解样品,电感耦合等离子体质谱法(ICP-MS)测定苦荞茶中铜、铅、镉、钴、镍的方法.方法具有灵敏度高、检出限低、精密度好、基体干扰少、准确可靠、快捷、简便的特点.各元素方法检出限(3SD,μg/L)分别为:铜0.009、铅0.023、镉0.015、钴0.022、镍0.035;方法精密度(RSD,n=12)分别为:铜2.5%～3.0%、铅2.1%～2.3%、镉3.0%～3.8%、钴2.5%～2.6%、镍1.5%～1.9%;各元素加标回收率分别为:铜95.0%～105.0%、铅95.0%～105.0%、镉98.0%～105.0%、钴95.0%～105.0%、镍95.0%～105.0%.在线用铑作为内标95.0%～105.0%.方法经国家一级标准物质验证,测定值与标准值吻合.应用于实际样品测定,结果满意.     

Dibenzomethanopentacene-Based Polymers of Intrinsic Microporosity for Use in Gas-Separation Membranes

Dibenzomethanopentacene (DBMP) is shown to be a useful structural component for making Polymers of Intrinsic Microporosity (PIMs) with promise for making efficient membranes for gas separations. DBMP-based monomers for PIMs are readily prepared using a Diels–Alder reaction between 2,3-dimethoxyanthracene and norbornadiene as the key synthetic step. Compared to date for the archetypal PIM-1, the incorporation of DBMP simultaneously enhances both gas permeability and the ideal selectivity for one gas over another. Hence, both ideal and mixed gas permeability data for DBMP-rich co-polymers and an amidoxime modified PIM are close to the current Robeson upper bounds, which define the state-of-the-art for the trade-off between permeability and selectivity, for several important gas pairs. Furthermore, long-term studies (over ≈3 years) reveal that the reduction in gas permeabilities on ageing is less for DBMP-containing PIMs relative to that for other high performing PIMs, which is an attractive property for the fabrication of membranes for efficient gas separations.     

Normal Coordinate Analysis for Polymer Systems: Capabilities and New Opportunities

Normal coordinate analysis is an important tool in studying the structure, dynamics, and physical properties of polymer systems. In this article the capabilities of normal coordinate analysis (NCA) are explored in some detail. The use of the eigenvalues and eigenvectors from NCA is catalogued for a wide variety of purposes: for assigning or interpreting polymer spectra, for structural determination, for constructing force fields, for computing heat capacity and other thermodynamic properties, and for computing other physical properties. Examples are given for crystals, melts, and amorphous systems. Also described are methods for characterizing the normal mode vectors that are especially useful for larger systems, in which a large amount of data must be analyzed or where visualization or animation fails. Finally, a recently developed method for eliminating negative eigenvalues in systems with tens of thousands of atoms, trajectory averaging, is presented. Also described are several advances in numerical linear algebra for speeding up the diagonalization phase and for computing physical properties without requiring full diagonalization of the Hessian matrix.     

Overview of Special Session B—Compositional and Structural Analysis of Biomass

Special Session B at the 29th Symposium on Biotechnology for Fuels and Chemicals was the first invited session at this symposium devoted to analytical methods. The special topic was added in response to numerous requests for information on new and innovative methods that could be applied in the growing renewable fuels industry. Presentation topics include analytical methods for the characterization and analysis of maize traits, tools for investigating cell wall limitations to enzymatic degradation, methods for customizing enzyme cocktails for biomass, new techniques for the analysis of carbohydrates, analytical methods that enhance our understanding of pretreatment, improved methods for monitoring process intermediates, and published standard analytical methods for biomass conversion processes.     

Treatment of Anomalous Vapor Diffusion in Polymers

The mechanics of thermally-activated gaseous diffusion in polymers have long been studied for development of theoretical understanding of the interactive forces responsible for the non-linear nature of diffusion and the resultant enthalpic changes in the polymer. Methodologies and calculations have been developed in this work for treatment of experimental data for elimination of thickness-related anomalies in water vapor diffusion and for delineation of pressure effects. Linearized data for different polymer thicknesses and the attendant internal thermal effects have been generated by using calculated single molecule diffusion values. Equally linear data are obtained for different pressures by the use of a graphical method from which identical diffusion values are obtained, independent of material thickness and external pressure. True comparisons and classification of polymers as to their diffusivities are thus possible for development of barrier materials for food and drug packaging and for protective encapsulation of electronic devices. Results will be reported for three structurally different polymers. This revised version was published online in July 2006 with corrections to the Cover Date.     

Analysis of urinary biomarkers for exposure to alkyl benzenes by isotope dilution gas chromatography-mass spectrometry

A validated GC-MS method for the analysis of urinary metabolites of alkyl benzenes is reported. Metabolites for exposure to toluene, xylene and ethylbenzene were analyzed simultaneously using stable isotope substituted internal standards. The method entailed acidic deconjugation of urine samples followed by extractive alkylation with pentafluorobenzyl bromide as alkylating agent. The resulting pentafluorobenzyl derivatives of ortho-, meta-, para-cresol, mandelic acid (MA), hippuric acid (HA) and ortho-, meta-, para-methylhippuric acid (MHA) were then quantified by SIM. Optimized reaction conditions for the extractive alkylation step are reported. The derivatives were found to be sufficiently stable for overnight batch analysis. The LODs were below 0.1 micromol/L for the cresols and below 1 micromol/L for MA and the HAs. Within-batch precision for o-MHA was 7%, for m-MHA 5%, for p-MHA 5.2% and below 5% for the rest of the analytes.     

Evaluation of the detection of biomolecules in capillary electrophoresis by contactless conductivity measurement

The sensitivity of contactless conductivity detection to amino acids, peptides and proteins in CE was studied for BGE solutions of different pH values. The LOD and analytical characteristics were compared for acidic and basic conditions and better results were in most cases found for buffers of low pH values. Linear dynamic ranges varied between two orders of magnitude for amino acids and peptides and three orders of magnitude for larger proteins. The concentration detection limits were found to be between 1.2 and 7.5 microM for the amino acids tested and for the larger molecules they varied between 2.6 microM for leucine enkephalin and 0.2 microM for HSA when using a buffer at pH 2.1.     

Method validation and determination of lisdexamfetamine and amphetamine in oral fluid,plasma and urine by LC–MS/MS

Lisdexamfetamine (LDX) is a long‐acting prodrug stimulant indicated for the treatment of attention‐deficit/hyperactivity disorder and binge‐eating disorder symptoms. In vivo hydrolysis of LDX amide bond releases the therapeutically active d ‐amphetamine (d ‐AMPH). Since toxicological tests in biological samples can detect AMPH from the use of some legal medications, efficient methods are needed in order to correctly interpret the results. The aim of this study was to develop and validate an LC–MS/MS method for the simultaneous quantification of LDX and its main biotransformation product AMPH in human oral fluid, plasma and urine. Calibration curve range for both analytes was 1–128 ng/mL in oral fluid and plasma and 4–256 ng/mL in urine, being the lowest concentration the limit of quantification. Accuracy of the determined values of the target analytes for the five control levels ranged from 94.8 to 111.7% for oral fluid, from 91.3 to 100.2% for plasma and from 94.8 to 109.8% for urine. Imprecision for the five control levels did not exceeded 12.8% for oral fluid, 16.2% for plasma and 17.1% for urine. The method developed for the three matrices was validated and was also successfully applied to assess real samples, showing for the first time the detection of LDX in oral fluid.     

Rapid screening of inorganic and organic anions in liquid by‐products from hydrothermal treatment of biomass by capillary electrophoresis

A simple and rapid capillary electrophoresis method with capacitively coupled contactless conductivity detection (CE‐C⁴D) for the simultaneous determination of inorganic and organic anions in liquid product obtained from the hydrothermal treatment of biomass residues is presented. Under the optimal analytical conditions, limits of detection ranged from 1.8 to 9.4 μM for most target solutes and 53 μM for citrate. Relative standard deviations were below 0.5% for migration times and within 0.6–6.5% for peak areas for all solutes. The proposed method was successfully applied for the rapid determination and screening of inorganic and organic anions in liquid product produced following differing hydrothermal treatment temperatures for banana and pineapple biomass, and the contribution of organic acid formation to acidity in the liquid was evaluated. CE‐C⁴D could be a suitable method for the optimization or tailoring of HTT conditions for desired liquid product composition, and additionally for determination of the best variety(s) of biomass to use in such processes.     

Simultaneous quantification of five anthraquinones in rat plasma by high-performance liquid chromatography with fluorescence detection

A sensitive high-performance liquid chromatographic method with fluorescence detection (excitation 435 and emission 515 nm) was established and validated for quantification of five anthraquinones (aloe-emodin, rhein, emodin, chrysophanol and physcion) in rat plasma. Following a single-step liquid-liquid extraction, the analytes and internal standard (1,8-dihydroxyanthraquinone) were separated on a reversed-phase C(18) column with water-phosphoric acid-methanol as mobile phase at a flow rate of 1 mL/min. The linear ranges of the calibration curves were 6.5-1300 ng/mL for aloe-emodin, 20-4000 ng/mL for rhein, 40-8000 ng/mL for emodin, 15-3000 ng/mL for chrysophanol and 13-2600 ng/mL for physcion. The lower limit of quantification was 6.5 ng/mL for aloe-emodin, 20 ng/mL for rhein, 40 ng/mL for emodin, 15 ng/mL for chrysophanol and 13 ng/mL for physcion. The mean accuracy was 94.3-105.1% for aloe-emodin, 90.3-108.8% for rhein, 92.6-106.7% for emodin, 95.8-103.8% for chrysophanol and 98.7-101.2% for physcion. The within-batch and between-batch precisions were < or = 5.5% and < or = 13.4%, respectively. This method is suitable for determining the five anthraquinones in plasma simultaneously and thus investigating the pharmacokinetics of anthraquinones from Xiexin decoction in rats.     

Determination of inorganic elements in animal feeds by NIRS technology and a fibre-optic probe

In the present work we study the use of near infra-red spectroscopy (NIRS) technology together with a remote reflectance fibre-optic probe for the analysis of the mineral composition of animal feeds. The method allows immediate control of the feeds without prior sample treatment or destruction through direct application of the fibre-optic probe on the sample.The regression method employed was modified partial least squares (MPLS). The calibration results obtained using forty samples of animal feeds allowed the determination of Fe, Mn, Ca, Na, K, P, Zn and Cu, with a standard error of prediction (SEP(C)) and a correlation coefficient (RSQ) of 0.129 and 0.859 for Fe; 0.175 and 0.816 for Mn; 5.470 and 0.927 for Ca; 2.717 and 0.862 for Na; 4.397 and 0.891 for K; 2.226 and 0.881 for P; 0.153 and 0.764 for Zn, and 0.095 and 0.918 for Cu, respectively.The robustness of the method was checked by applying it to 10 animal feeds samples of unknown mineral composition in the external validation.     

Extracellular vesicles based electrochemical biosensors for detection of cancer cells: A review

Extracellular vesicles (EVs) derived from cancer cells are considered as ideal biomarker for liquid biopsy in cancer diagnosis, and are stable and abundant. Electrochemical methods for the detection of EVs are preferred over conventional methods such as Western blotting and enzyme-linked immunosorbent assay for their high sensitivity and real-time detection. This article summaries studies proposing the electrochemical methods utilizing immunological and molecular methodologies for detecting EVs derived biomacromolecules such as miRNAs and transmembrane protein for cancer diagnosis. Moreover, the electrochemical detection methods are compared and future prospects for the development of electrochemical methods for EVs detection are concluded.     

Economic analysis of ethanol production in California using traditional and innovative feedstock supplies

In this article, we estimate the costs of using alternative feedstocks to produce ethanol in a 40 million-gal facility in California’s San Joaquin Valley. Feedstocks include corn imported from Midwestern states and locally grown agricultural products such as corn, grapes, raisins, oranges, and other tree fruits. The estimated feedstock costs per gallon of ethanol include $0.92 for Midwestern corn, $1.21 for locally grown corn, $6.79 for grapes, $3.36 for raisins, $3.92 for citrus, and $1.42 for other tree fruit. Adjusting for coproduct values lowers the estimated net feedstock costs to $0.67/gal of ethanol for Midwestern corn, $0.96 for locally grown corn, $6.53 for grapes, and $3.30 for raisins. We also examine the potential increases in net revenue to raisin producers, made possible by having an alternative outlet available for selling surplus raisins.     

Epitope Imprinting of Phospholipids by Oriented Assembly at the Oil/Water Interface for the Selective Recognition of Plasma Membranes

Phospholipids, as fundamental building blocks of the cell membrane, play important roles for molecule transportation, cell recognition, etc. However, due to the structural diversity and amphipathic nature, there are few methods for the specific recognition of lipids as compared to other biomolecules such as proteins and glycans. Herein, we developed a molecular imprinting strategy for controllable imprinting toward the polar head of phospholipid exposed on the surface of cellular membranes for recognition. Phosphatidylserine, as unique lipid on the outer membrane leaflet of exosome and also hallmark for cell apoptosis, was imprinted with the developed method. The phosphatidylserine imprinted materials showed high efficiency and specific targeting capability not only for apoptotic cell imaging but also for the isolation of exosomes. Collectively, the synthesized molecularly imprinted materials have great potential for selective plasma membrane recognition for targeted drug delivery and biomarker discovery.     

盐酸氯丙嗪作探针二级散射和倍频散射法测定环境水样中某些阴离子表面活性剂

在pH3.0~5.0的HAc-NaAc缓冲溶液中,盐酸氯丙嗪与十二烷基苯磺酸钠、十二烷基磺酸钠和十二烷基硫酸钠等阴离子表面活性剂反应形成离子缔合物时,仅能引起吸收光谱和荧光光谱的微小变化,但却能导致二级散射(SOS)和倍频散射(FDS)的显著增强。最大SOS峰均在552nm附近,最大FDS峰均在390nm附近。其中SOS法灵敏度更高,它对十二烷基苯磺酸钠、十二烷基硫酸钠和十二烷基磺酸钠的检出限分别为0.047、0.106和0.117mg/L,而其线性范围分别为0.2~12、0.4~15和0.4~20.0mg/L。研究了反应产物的吸收、荧光、SOS和FDS光谱特征、适宜的反应条件及分析化学性质,据此发展了一种用SOS技术灵敏、简便、快速测定阴离子表面活性剂的环境友好型新方法。     

Evaluation of adsorbent materials for heat pump and thermal energy storage applications in open systems

The evaluation of solid adsorbents in open sorption systems for heating, cooling and thermal energy storage (TES) applications is crucial for the ecological and economical performance of these systems. An appropriate adsorbent has to reach the temperature limit given by the heating/cooling system of the consumer. It has to provide high energy efficiency and a high energy density for storage applications. A method for an easy evaluation of different adsorbents for a specific application has been developed. The method is based on the adsorption equilibrium of the adsorbent and water vapor. The crucial property for the discussed field of applications is the differential heat of adsorption. Criteria for the evaluation of the adsorbent are the breakthrough curves (responsible for the dynamics of the process), the possible temperature lift (or the dehumidification) of the air, the thermal COP and the storage capacity.     

Simultaneous determination of fluoroquinolones,sulfonamides and tetracyclines in sewage sludge by pressurized liquid extraction and liquid chromatography electrospray ionization-mass spectrometry

A new scheme for the quantitative determination of traces of fluoroquinolones (FQs), tetracyclines (TCs) and sulfonamides (SAs) in sewage sludge was developed. The compounds were simultaneously extracted from sewage sludge by pressurized liquid extraction (PLE). A novel and effective method for PLE was developed. Solid-phase extraction was used for cleaning up the extracts. Identification and quantification of the compounds was done using high-performance liquid chromatography with electrospray ionization mass spectrometry in selected reaction monitoring mode. The best recovery of FQs and TCs was obtained by using hydrophilic–lipophilic balance cartridges, recoveries ranged 59% for norfloxacin to 82% for ofloxacin and 95% for doxycycline; for SAs strong cation-exchange cartridges were more efficient, recoveries were 96% for sulfamethoxazole and 43% for sulfadimethoxine. Limit of quantification ranged from 0.1 ng/g for SAs to 160 ng/g for tetracycline. Method precision for TCs was 5.06% and 1.12%, and for SAs 0.43% and 2.01%. FQs precision ranged from 0.77% to 1.89%.     

A sensitive electrochemical chlorophenols sensor based on nanocomposite of ZnSe quantum dots and cetyltrimethylammonium bromide

In this work, a very sensitive and simple electrochemical sensor for chlorophenols (CPs) based on a nanocomposite of cetyltrimethylammonium bromide (CTAB) and ZnSe quantum dots (ZnSe–CTAB) through electrostatic self-assembly technology was built for the first time. The composite of ZnSe–CTAB introduced a favorable access for the electron transfer and gave superior electrocatalytic activity for the oxidation of CPs than ZnSe QDs and CTAB alone. Differential pulse voltammetry (DPV) was used for the quantitative determination of the CPs including 2-chlorophenol (2-CP), 2,4-dichlorophenol (2,4-DCP) and pentachlorophenol (PCP). Under the optimum conditions, the peak currents of the CPs were proportional to their concentrations in the range from 0.02 to 10.0 μM for 2-CP, 0.006 to 9.0 μM for 2,4-DCP, and 0.06 to 8.0 for PCP. The detection limits were 0.008 μM for 2-CP, 0.002 μM for 2,4-DCP, and 0.01 μM for PCP, respectively. The method was successfully applied for the determination of CPs in waste water with satisfactory recoveries. This ZnSe–CTAB electrode system provides operational access to design environment-friendly CPs sensors.