焙烧温度对CuO/Fe2O3/ZrO2甲醇水蒸气重整制氢催化剂性能的影响

采用XRD、TPR和EXAFS等手段，考察了焙烧温度对CuO/Fe2O3/ZrO2物化性能和甲醇水蒸气重整制氢活性及其选择性的影响。结果表明，催化剂中氧化铜的晶粒随着焙烧温度的提高而增大，铜的配位环境发生变化。在焙烧温度623K－723K范围内，对甲醇水蒸气重整反应的甲醇转化率和氢选择性影响较小，其结构参数变化值较小。当焙烧温度提高到923K时，催化剂的活性因ZrO2晶化和铜组分的聚焦而显著降低。结果铁的加入使ZrO2的相变温度向后推移，并且有效地阻止了CuO颗粒的聚集。     

费-托合成Co/ZrO2-Al2O3催化剂反应性能的研究

以ZrOCl2·6H2O和AlCl3为原料，采用共沉淀方法制得一系列不同ZrO2质量分数的ZrO2-Al2O3混合氧化物载体；并以该混合氧化物为载体，采用初湿浸渍法制得钴质量分数为12％的Co/ZrO2-Al2O3催化剂。XRD、NH3-TPD、TPR和原位IR等表征结果表明，随着混合载体中ZrO2质量分数的增加，载体比表面积先增加后减少，混合载体的平均孔径则小于单一氧化物ZrO2和Al2O3的平均孔径。ZrO2和Al2O3载体混合后会导致氧化物的比表面积和酸性增大并且有新的物相生成。当混合氧化物用作载体时，能够抑制载体表面金属钴的分散，改变催化剂的还原行为，降低催化剂对CO物种的吸附能力。CO加氢反应表明，与单一金属氧化物相比，钴负载ZrO2-Al2O3混合氧化物催化剂的加氢活性和重质烃选择性有所降低。     

Effects of calcination and reduction temperature on the performance of Co-Pt-ZrO2/γ-A12O3 catalysts for Fischer-Tropsch synthesis

采用浸渍法制备了Co-Pt-ZrO2/γ-Al2O3催化剂,对其进行了BET、XRD和TPR等表征,并在浆态床反应器上考察了焙烧温度和还原温度对催化剂费托合成反应性能的影响.结果表明,焙烧温度过高,容易造成Co物种和载体间的相互作用增强,使部分氧化钻颗粒聚集或烧结,导致催化剂的F-T合成反应活性和C5+烃选择性降低.还原温度较低时,钴物种不能充分还原,CO加氢活性低,甲烷选择性高,重质烃选择性低;还原温度过高,则可能造成活性物种的烧结,反而降低了催化剂的活性和重质烃选择性.在原料气n(H2)/n( CO)=2.0、483 K、2.4 MPa和空速3.6 L/( gcat·h)的条件下,31.08％ Co～0.11％Pt ～ 7.16％ ZrO2/Al2O3催化剂在673 K焙烧.纯H2下653 K还原后,其费托性能最佳;CO转化率为27.0％,C5+的选择性为83.0％.     

Re组分及ZrO_2载体制备方法对Ru-Re/ZrO_2催化丙三醇氢解反应的影响

分别采用沉淀法、水热合成法和不同气氛下焙烧的方式制备了ZrO2载体,采用浸渍法负载Ru及Ru-Re组分制备了Ru/ZrO2和Ru-Re/ZrO2催化剂.利用氮气吸附-脱附、X射线衍射、透射电镜及程序升温还原等方法对样品的比表面积、孔容、平均孔径、晶体结构、形貌及还原特性等进行了表征.考察了Re组分及ZrO2载体制备方法对催化剂在丙三醇氢解制丙二醇反应中的催化性能的影响.结果表明,不同方法制备的ZrO2载体对负载型Ru催化剂的催化性能有一定影响,其中以沉淀法在空气中焙烧制得ZrO2负载活性组分后得到的催化剂的活件相对较低(转化率18.7%),而以沉淀法在氮气中焙烧以及水热合成法制备的ZrO2负载活性组分后得到的催化剂的活性相对较高(转化率25.8%).Re组分的引入对Ru/ZrO2系列催化剂的催化性能有明显的促进作用.     

Effect of preparation condition on catalytic performance of Ni/ZrO2-SiO2 for methanation of coal gas

采用浸渍法制备了ZrO2-SiO2复合载体和Ni质量分数为6％的Ni/ZrO2 -SiO2催化剂,考察了载体制备时浸渍溶液pH值、焙烧温度和催化剂制备时的焙烧温度对Ni/ZrO2-SiO2催化剂煤气甲烷化反应性能的影响.采用X射线衍射、程序升温还原和扫描电子显微镜等方法对催化剂进行了表征.结果表明,载体浸渍溶液pH值为8.0 ～9.0,载体焙烧温度为550℃,催化剂焙烧温度为450℃时,Ni/ZrO2-SiO2催化剂在煤气甲烷化反应中显示了最优的催化性能,CO转化率100％,CO2转化率1.8％,CH4生成速率16.6 mmol/(h·g).进一步表征发现,制备ZrO2-SiO2复合载体时,增大浸渍溶液的pH值有利于形成粒径较小的亚稳态四方晶相ZrO2,可见四方晶相ZrO2更有利于甲烷化反应;载体焙烧温度会影响到NiO粒径的大小和其在催化剂表面的分散,温度过高和过低都会导致NiO粒径大小的不适宜以及分散性的降低;催化剂焙烧温度过高则会导致NiO与载体间的相互作用减弱,NiO分散性降低.     

钴负载量和焙烧温度对F-T合成用Co/Al2O3催化剂活性的影响

 对用于F－T合成制液态烃的Co／Al2O3催化剂进行了程序升温还原研究,确定了合适的还原活化温度（约600～800K）,同时考察了钴负载量和焙烧温度对催化剂活性的影响．结果表明,钴负载量和焙烧温度对C5＋收率的影响十分显著．用CODEX优化软件对钴负载量和催化剂焙烧温度进行了优化．结果表明,比较理想的钴负载量为11．6％,焙烧温度为651K．XRD测试结果表明,在较高温度焙烧的催化剂由于易生成CoAl2O4尖晶石,导致催化剂的活性显著降低．     

负载型纳米ZrO2/Al2O3复合载体的制备和表征及其Ni/ZrO2/Al2O3催化性能的研究

以大孔Al2O3为基载体，采用沉积-沉淀法和溶胶-沉积法制备了负载型纳米ZrO2/Al2O3复合载体．用XRD、TEM和比表面与孔径测定等手段对载体进行了表征．结果表明，负载型纳米ZrO2/Al2O3复合载体具有较大的比表面积和适宜的孔径分布，纳米ZrO2在载体上呈单层均匀分布．以CH4-CO2重整制合成气为探针反应，考察了Ni/ZrO2/Al2O3催化剂的活性和选择性．     

氧化铝负载钌基氨合成催化剂的制备条件及载体改性

 利用等体积浸渍法制备了氧化铝负载钌基氨合成催化剂．考察了\r\n氢氧化铝的焙烧温度，催化剂的还原温度，助剂K、Ba和Sm的添加，以\r\n及用MgO和BaO改性氧化铝载体等对催化剂活性的影响．通过XRD，N2物\r\n理吸附和CO2化学吸附等方法表征了载体的物相结构、比表面积和表面\r\n碱性．研究结果表明，氧化铝表面碱性随着氢氧化铝焙烧温度的升高而\r\n增大是催化剂活性升高的主要原因，载体比表面积的降低对催化剂活性\r\n的影响相对较小．助剂K、Ba和Sm的加入显著地提高了催化剂的活性，\r\n同时助剂Ba和Sm还减弱了强吸附氢对氮吸附的抑制作用，明显提高了催\r\n化剂的高压活性．用MgO改性氧化铝载体降低了其比表面积，但是显著\r\n地提高了载体的表面碱性和催化剂的活性．BaO改性的氧化铝载体的比\r\n表面积、表面碱性及其负载的钌基催化剂的活性随着BaO含量的增加先\r\n升高后降低，当BaO摩尔含量为7．7％时，催化剂活性最高．     

镍基催化剂上糠醛选择性加氢合成糠醇

采用浸渍法制备了一系列负载的Ni催化剂,用于糠醛选择性加氢反应.用XRD、TPR等手段对Ni/γ-Al2O3样品进行了表征.结果表明,Ni负载量在5~|15%范围内,高度分散于载体γ-Al2O3表面,Ni负载量进一步提高到20%,则在载体表面聚集成为微晶.在10%Ni/γ-Al2O3样品上提高焙烧温度有利于Ni的前驱体分解且高度分散于载体表面.Ni2 与γ-Al2O3存在较强的相互作用,但这种相互作用随着Ni负载量的增加而逐渐减弱,随着焙烧温度的增加而逐渐增强.与其他载体负载的Ni催化剂相比,Ni/γ-Al2O3由于其大的表面和适当的表面结构,在糠醛加氢反应中表现出一定的活性和较高的选择性,且随着Ni负载量的增加,活性逐渐增强,但选择性有所下降.另外催化剂的焙烧温度、还原温度,反应温度和溶剂对该反应均有较大影响,采用极性有机溶剂,适宜的焙烧和还原温度有利于催化剂活性和选择性的提高.     

Co/Hβ催化剂上N_2O的分解性能研究

采用浸渍法制备了Hβ分子筛负载钴氧化物催化剂。考察了催化剂焙烧温度和钴负载量对催化剂催化分解N2O活性的影响,并采用XRD、NH3-TPD、H2-TPR、SEM等手段对催化剂的理化性质进行表征。结果表明,催化剂中的钴物种主要以Co3O4尖晶石型形态存在;催化剂焙烧温度显著影响其酸性和酸量及氧化还原性能,焙烧温度达到700℃后,催化剂中有难还原的Co-Al-O物种生成。焙烧温度和钴负载量对催化剂的催化活性均有影响,焙烧温度为600℃、钴负载量为10%~15%的催化剂催化活性好,N2O分解温度低,t10、t50和t95分别为325~329℃、364~367℃和406~408℃。     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

化学计量中不确定度评定研究进展

测量不确定度是表征合理地赋予被测量之值的分散性的参数。本文针对化学计量不确定度评定基础模型仅适用于线性模型、概率分布为正态分布或缩放位移t分布等局限,介绍了近年来不确定度评定的研究热点:蒙特卡罗方法(Monte Carlo Method,MCM),不确定度评定的来源、评定概念、评估方法及其发展过程,扩大了测量不确定度评定与表示的适用范围。     

微量钙的测定方法研究进展

介绍了1995-2006年期间测定微量和痕量钙的方法,如电感耦合等离子体-原子发射光谱法、原子吸收光谱法以及离子色谱法等的工作原理和特点,并说明了其测定微量钙的应用领域。并对微量钙的测定技术进行了展望(引用文献55篇)。