Spectrophotometric determination of copper(II) using oximidobenzotetronic acid

Summary Oximidobenzotetronic acid (OBTA) is proposed as a sensitive spectrophotometric reagent for the estimation of 0.5–3.0 ppm of copper(II) at 427 nm in 50% dioxan at p_H 5.3–7.5. For the estimation of 2 ppm Cu(II), 1.3 ppm Ni(II), 1.3 ppm Co(II), 3.2 ppm Fe(II), 10.3 ppm Fe(III), 9.7 ppm Ce(IV), 300 ppm acetate, 160 ppm oxalate, 95 ppm tartrate, 50 ppm citrate, as well as Zn(II), Cd(II), Hg(II)) Pb(II), Mn(II), As(III) as well as (V), Th(IV), Be(II), Ce(III), La(III), V(V) and Mo(VI), even when present in large quantities, do not interfere. The interference due to 25 ppm Bi(III), 20 ppm Sb(III), 20 ppm Sn(II), 25 ppm Sn(IV) and 30 ppm W(VI) can be removed by the addition of 95 ppm tartrate ions.

---

Zusammenfassung Oximidobenzotetronsäure wurde als empfindliches Reagens zur spektrophotometrischen Bestimmung von 0,5 bis 3,0 ppm Kupfer(II) bei 427 nm in 50%iger Dioxanlösung bei p_H 5,3 bis 7,5 vorgeschlagen. Die Anwesenheit von 1,3 ppm Ni(II), 1,3 ppm Co(II), 3,2 ppm Fe(II), 10,3 ppm Fe(III), 9,7 ppm Ce(IV), 300 ppm Acetat, 160 ppm Oxalat, 95 ppm Tartrat, 50 ppm Citrat sowie die Anwesenheit auch großer Mengen Zn(II), Cd(II), Hg(II), Pb(II), Mn(II), As(III) bzw. (V), Th(IV), Be(II), Ce(III), La(III), V(V) und Mo(VI) stören die Bestimmung von 2 ppm Cu(II) nicht. Der störende Einfluß von 25 ppm Bi(III), 20 ppm Sb(III), 20 ppm Sn(II), 25 ppm Sn(IV) und 30 ppm W(VI) kann durch Zusatz von 95 ppm Tartrat beseitigt werden.

     

Anion-exchange behavior of various metals in hydrazoic acid media

The adsorption characteristics for 43 metals on a strongly basic ion-exchange resin Bio-Rad AG1 were examined in 0.5 M hydrazoic acid solution. The distribution coefficients for V(IV), Fe(III), Cu(II), Zn, Se(IV), Mo(VI), Pd(II), Cd, In(III), Rc(VII), Hg(II) and U(VI), which showed very strong adsorption except for Cd, were measured as a function of hydrazoic acid concentration over the range 0.05–0.5 M. Favorable differences in the distribution coefficients allow useful two- and three-component separations such as Co(II)-Fe(III), As(III)-V(IV), Cd-Zn, Cd- Hg(II), Te(IV)-Se(IV), Th-U(VI), Mn(II)-Mo(VI)-Re(VII), to be achieved on a small column.     

Oximidobenzotetronic acid as a reagent for the separation and gravimetric determination of palladium and cobalt

Oximidobenzotetronic acid is recommended for the separation and gravimetric determination of palladium and cobalt An ethanolic solution of the reagent quantitatively precipitates palladium(II) from solutions which are 0.75 N in acid up to pH 5.1, the complex is weighed as Pd(C₉H₅NO₄)₂. Cobalt(II) can be determined in the filtrate after the precipitation of palladium. With 0.5 N acid solutions, no interference was found from Pt(IV), Ir(IV), Rh(III), Ru(III), Os(IV), Au(III), Ag(I), Cu(II), Fe(III), Ni(II), Hg(II). Pb(II), Bi(III), Cd(II), As(V), Se(VI), Te(IV), Mo(VI), Sb(III), Al(III), Cr(III), Zn(II), Ti(IV), Zr(IV). acetate, oxalate, citrate, tartrate, phosphate and fluoride.     

Sulfonylcalix[4]arenetetrasulfonate as pre-column chelating reagent for selective determination of aluminum(III), iron(III), and titanium(IV) by ion-pair reversed-phase high-performance liquid chromatography with spectrophotometric detection

Sulfonylcalix[4]arenetetrasulfonate (SO₂CAS) has been examined as a pre-column chelating reagent for ultratrace determination of metal ions by ion-pair reversed-phase high-performance liquid chromatography with spectrophotometric detection. Metal ions were converted into the SO₂CAS chelates in an acetic buffer solution (pH 4.7). The chelates were injected onto a n-octadecylsilanized silica-type Chromolith™ Performance RP-18e column and were eluted using a methanol (50 wt.%)-water eluent (pH 5.6) containing tetra-n-butylammonium bromide (7.0 mmol kg⁻¹), acetate buffer (5.0 mmol kg⁻¹), and disodium ethylendiamine-N,N,N′,N′-tetraacetate (0.10 mmol kg⁻¹). Under the conditions used, Al(III), Fe(III), and Ti(IV) were selectively detected among 21 kinds of metal ions [Al(III), Ba(II), Be(II), Ca(II), Cd(II), Co(II), Cr(III), Cu(II), Fe(III), Ga(III), Hf(IV), In(III), Mg(II), Mn(II), Mo(VI), Ni(II), Pb(II), Ti(IV), V(V), Zn(II), and Zr(IV)]. The detection limits on a 3σ blank basis were 8.8 nmol dm⁻³ (0.24 ng cm⁻³) for Al(III), 7.6 nmol dm⁻³ (0.42 ng cm⁻³) for Fe(III), and 17 nmol dm⁻³ (0.80 ng cm⁻³) for Ti(IV). The practical applicability of the proposed method was checked using river and tap water samples.     

Organic acid solutions in the chromatography of inorganic ions VIII. Cation-exchange of Mn(II), Cd(II), Co(II), Ni(II), Zn(II), Cu(II), Fe(III), Sc(III), Y(III), Eu(III), Dy(III), Ho(III), Yb(III), Ti(IV) and Nb(V) in malate media

Summary The cation-exchange behaviour of Mn(II), Cd(II), Co(II), Ni(II), Zn(II), Cu(II), Fe(III), Sc(III), Y(III), Eu(III), Dy(III), Ho(III), Yb(III), Ti(IV) and Nb(V) in malate media at various concentrations and pH, was studied with Dowex 50 WX8 resin (200–400 mesh) in the ammonium form. Separation of Fe(III)/Cu(II), Fe(III)/Cu(II)/Zn(II), Fe(III)/Co(II)/Mn(II), Cu(II)/Ni(II)/Mn(II), Fe(III)/Cu(II)/Co(II)/Mn(II), Fe(III)/Cu(II)/Ni(II)/Cd(II), Yb(III)/Eu(III), Sc(III)/Y(III),Sc(III)/Yb(III)/Dy(III) and Nb(V)/Yb(III)/Ho(III) has been achieved, among others.This work was supported by C.N.R. of Italy.     

The spectrophotometric determination of vanadium after extraction as vanadium(III) ferronate by tribenzylamine

Vanadium(III) obtained by dithionite reduction of vanadium(V) can be extracted as its ferron complex with tribenzylamine in chloroform from 0.05 M sulphuric acid. Vanadium (0–5 μg ml^-1) is determined spectrophotometrically at 430 nm with a sensitivity of 0.0028 μg V cm^-2. Al(III), Co(II), Ni(II), Fe(II, III), Hg(II), Si(IV), Be(II), Mg(II), Ca(II), Sr(II), Ba(II), Cr(VI, III), W(VI), Zn(II), U(VI), Mn(II). Pb(II), Cu(II), Cd(II) and Th(IV) do not interfere; only Mo(VI), Ti(IV), Zr(IV). Bi(V) and Sn(II) interfere. A single determination takes only 7 min. The extracted complex is V^III (R-3H.TBA)₃ where R = C₉H₄O₄NSI. The method is satisfactory for the determination of vanadium in steels, alum and other samples without preliminary separations.     

Extraction of Ag(I), Cd(II), In(III), Sn(II), Sn(IV), Sb(III), and U(VI) from aqueous solutions by ketone solutions using single-step batch and continuous SISAK methods1,2

The extraction properties of Ag(I), Cd(II), In(III), Sn(II), Sn(IV), Sb(III), and U(VI) from aqueous KI/H₂SO₄ solution into a mixture of 4-methyl-2-pentanone (methyl isobutyl ketone, MIBK) and cyclohexanone (CHO) were studied. Both single-step batch and SISAK² methods were used. The oxidation of Sn(II) to Sn(IV) by iodine and complexation of Sn(IV) by 2,3-dimercapto-propanol-1 (BAL) were also investigated. A method for rapid and continuous separation of indium from tin was developed for investigation of short-lived indium fission products.     

The polarographic determination of traces of titanium-(IV) in the presence of n-benzoyl-n-phenylhydroxylamine

The polarographic behavior of the titanium(IV)-N-benzoyl-N-phenyl-hydroxylamine (BPHA) system in acidic medium and in water-ethanol mixtures has been studied. In (1+3) water-ethanol containing 2 M sulfuric acid and 0.05 M BPHA, titanium(IV) gives a single kinetically controlled wave. Titanium(IV) can be determined at concentrations as low as 5·10^-6M, in the presence of Fe(III), Cu(II), V(V), etc., but Cd(II), Sn(II and IV), As(V), U(VI) and Mo(VI) interfere.     

Spectrometric Studies on the Complexation of Pd(II), Fe(III) and Pt(IV) with mandelazo I

Abstract

A spectrometric study of the reaction between Pd(II), Fe(III) and Pt(IV) ions, and Mandelazo I was carried out. The optimum conditions favouring the formation of the complexes are extensively investigated. The stoichiometry of the complexes formed in solution (1:2, 1:1, 1:1), their apparent stability constants (5.45 × 10⁹, 2.39 × 10⁶, 4.12 × 10⁵) and the ranges for obedience to beer's law (0.2 – 6.4, 0.25 – 7.0, 1.5 – 42.0 μg/mL) are reported for Pd(II), Fe(III) and Pt(IV), respectively. The effect of some metal ions including Cu(II), Zn(II), Mn(II), Cd(II), Hg(II), Co(II), Ni(II), Be(II), Al(III), Th(IV) and U(VI), on the maximum absorbance of the formed complexes was also investigated.     

Organic acid solutions in the chromatography of inorganic ions. VII. Cation exchange of Mg(II), Ca(II), Sr(II), Ba(II), Mn(II), Cd(II), Co(II), Ni(II), Zn(II), Cu(II) and Fe(III) in succinate media

Summary The cation-exchange behaviour of Mg(II), Ca(II), Sr(II), Ba(II), Mn(II), Cd(II), Co(II), Ni(II), Zn(II), Cu(II) and Fe(III) in succinate media at various concentrations and pH, was studied with Dowex 50 WX8 resin (200–400 mesh) in the NH ₄ ⁺ form. As examples separations of Cd(II)/Co(II), Cd (II)/Ni(II), Fe(III)/Cu(II)/Ni(II) and Mg(II)/Ca(II)/Sr(II)/Ba(II) have been achieved.This work was supported by C.N.R. of Italy.     

Heteronuclear complexes of oxorhenium(V) with Fe(III), Co(II), Ni(II), Cu(II), Cd(II) and UO2(VI) and their biological activities

Heteronuclear complexes containing oxorhenium(V), with Fe(III), Co(II), Ni(II), Cu(II), Cd(II) and UO₂(VI) ions were prepared by the reaction of the complex ligands [ReO(HL¹)(PPh₃)(OH₂)Cl]Cl (a) and/or [ReO(H₂L²)(PPh₃)(OH₂)Cl]Cl (b), where H₂L¹?=?1-(2-hydroxyphenyl)butane-1,3-dione-3-(5,6-diphenyl-1,2,4-triazine-3-ylhydrazone) and H₃L²?=?1-(2-hydroxyphenyl)butane-1,3-dione-3-(1H-benzimidazol-2-ylhydrazone), with transition and actinide salts. Heterodinuclear complexes of ReO(V) with Fe(III), Co(II), Ni(II), Cu(II) and Cd(II) were obtained using a 1?:?1 mole ratio of the complex ligand and the metal salt. Heterotrinuclear complexes were obtained containing ReO(V) with UO₂(VI) and Cu(II) using 2?:?1 mole ratios of the complex ligand and the metal salts. The complex ligands a and b coordinate with the heterometal ion via a nitrogen of the heterocyclic ring and the nitrogen atom of the C=N⁷ group. All transition metal cations in the heteronuclear complexes have octahedral configurations, while UO₂(VI)?complexes have distorted dodecahedral geometry. The structures of the complexes were elucidated by IR, ESR, electronic and ¹H NMR spectra, magnetic moments, conductance and TG-DSC measurements. The antifungal activities of the complex ligands and their heteronuclear complexes towards Alternaria alternata and Aspergillus niger showed comparable behavior with some well-known antibiotics.     

A potentiometric study of the oxidation of cobalt(II) with gold(III) chloride in presence of 1,10 phenanthroline or 2,2'-bipyridine : A new titration of cobalt (II) and its application to nickel-base alloys

The redox reaction between cobalt(II) and gold(III) chloride in the presence of 1.10-phenanthroline or 2,2'-bipyridine was studied, and a titration of the cobalt(II) complex with a gold(III) chloride solution was developed. A 4-fold amount of 1,10-phenanthroline or 2,2'-bipyridine was necessary for rapid quantitative reaction; the permissible pH range was 1.5–5. The oxidation of the cobalt(II) complex proceeds rapidly at 40–50°C, and a direct potentiometric titration was possible. The following maximum errors were obtained: 3.3% for 0.2–1.0 mg Co, 2.0% for 1–5 mg Co, and 0.70% for 10–40 mg Co. The following ions did not interfere: Ni(II), Zn(II), Pb(II), Cd(II), Mn(II), Fe(II), Cr(III), Al(III), Th(IV), Se(IV), Ti(IV), U(VI), Mo(VI), SO^2-₄ and PO^3-₄. Even small quantities of silver(I), copper(II), palladium(II), mercury(II)and iron(III) interfered. The method was applied to the determination of high cobalt contents in high-temperature nickel-base alloys.     

Voltammetry and controlled-potential coulometry with boron carbide electrodes

With the boron carbide electrode, E_{p$\text{p}\text{2}$} values were determined for the reduction of the following ions: Cd(II), Co(II), Cu(II), Fe(III), Ni(II), Pb(II), Ru(IV), Sb(V), and U(VI). The linear dependence of peak current on concentration is demonstrated for the U(VI) → U(IV) and Fe(III) → Fe(II) reductions at the boron carbide electrode. The suitability of the electrode for the controlled-potential coulometric ti trations of Fe(II) → Fe(III), Fe(III) → Fe(II), and U(VI) → U(IV) was studied; the results were inconclusive because of the small surface area that could be used conveniently and the possibility of oxygen leaks in the cell.     

Hg(II), Tl(III), Cu(I), and Pd(II) Complexes with 2,2'-Diphenyl-4,4'-Bithiazole (DPBTZ), Syntheses and X-Ray Crystal Structure of [Hg(DPBTZ)(SCN)2]

Reaction of the ligand 2,2′-diphenyl-4,4′-bithiazole (DPBTZ) with Hg(SCN)₂, Tl(NO₃)₃, CuCl, and PdCl₂ gives complexes with stoichiometry [Hg(DPBTZ)(SCN)₂], [Tl(DPBTZ)(NO₃)₃], [Cu(DPBTZ)(H₂O)Cl]_, and [Pd(DPBTZ)Cl₂]. The new complexes were characterized by elemental analyses and infrared spectroscopy. The crystal structure of [Hg(DPBTZ)(SCN)₂] determined by X-ray crystallography. The Hg atom in the title monomeric complex, (2,2′-diphenyl-4,4′-bithiazole)mercury(II)bisthiocyanate, [Hg(C₁₈H₁₂N₂S₂)(SCN)₂], is four-coordinate having an irregular tetrahedral geometry composed of two S atoms of thiocyanate ions [Hg-S 2.4025(15) and 2.4073(15) Å] and two N atoms of 2,2′-diphenyl-4,4′-bithiazole ligand [Hg-N 2.411(4) and 2.459(4) Å]. The bond angle S(3)-Hg(1)-S(4) of 147.46(5)° has the greatest derivation from ideal tetrahedral geometry. Intermolecular interaction between Hg(1) and two S atoms of two neighboring molecules, 3.9318(15) and 3.9640(18) Å, make the Hg(1) distort from a tetrahedron to a disordered octahedron. The attempts for preparation complexes of Tl(I), Pb(II), Bi(III), Cd(II) ions with 2,2′-diphenyl-4,4′-bithiazole ligand were not successful and also the attempts for preparation complexes of 4,4′,5,5′-tetraphenyl-2,2′-bithizole ligand with Cu(II), Ni(II), Co(II), Co(III), Mn(II), Mn(III), Fe(II), Fe(III), Cr(III), Zn(II), Tl(III), Pb(II), Hg(II), Cu(I), Pd(II) were not successful. This point can be regarded as the initial electron withdrawing of phenyl rings and also their spatial steric effects.     

Amberlite XAD-7 impregnated with Xylenol Orange: a chelating collector for preconcentration of Cd(II), Co(II), Cu(II), Ni(II), Zn(II) and Fe(III) ions prior to their determination by flame AAS

A new chelating resin, Xylenol Orange coated Amberlite XAD-7, was prepared and used for preconcentration of Cd(II), Co(II), Cu(II), Fe(III), Ni(II) and Zn(II) prior to their determination by flame atomic absorption spectrophotometry. The optimum pH values for quantitative sorption of Cd(II), Co(II), Cu(II), Fe(III), Ni(II) and Zn(II) are 4.5–5.0, 4.5, 4.0–5.0, 4.0, 5.0 and 5.0–7.0, respectively, and their desorptions by 2 mol L^–1 HCl are instantaneous. The sorption capacity of the resin has been found to be 2.0, 2.6, 1.6, 1.6, 2.6 and 1.8 mg g^–1 of resin for Cd, Co, Cu, Fe, Ni and Zn, respectively. The tolerance limits of electrolytes, NaCl, NaF, NaI, NaNO₃, Na₂SO₄ and of cations, Mg²⁺ and Ca²⁺ in the sorption of the six metal ions are reported. The preconcentration factor was between 50 and 200. The t_1/2 values for sorption are found to be 5.3, 2.9, 3.2, 3.3, 2.5 and 2.6 min for the six metals, respectively. The recoveries are between 96.0 and 100.0% for the different metals at preconcentration limits between 10 to 40 ng mL^–1. The preconcentration method has been applied to determine the six metal ions in river water samples after destroying the organic matter (if present in very large amount) with concentrated nitric acid (RSD ≤ 8%, except for Cd for which it is upto 12.6%) and cobalt content of vitamin tablets with RSD of ～ 3.0%.     

Zwitterion-functionalized polymer microspheres as a sorbent for solid phase extraction of trace levels of V(V), Cr(III), As(III), Sn(IV), Sb(III) and Hg(II) prior to their determination by ICP-MS

This paper describes the preparation of zwitterion-functionalized polymer microspheres (ZPMs) and their application to simultaneous enrichment of V(V), Cr(III), As(III), Sn(IV), Sb(III) and Hg(II) from environmental water samples. The ZPMs were prepared by emulsion copolymerization of ethyl methacrylate, 2-diethylaminoethyl methacrylate and triethylene glycol dimethyl acrylate followed by modification with 1,3-propanesultone. The components were analyzed by elemental analyses as well as Fourier transform infrared spectroscopy, and the structures were characterized by scanning electron microscopy and transmission electron microscopy. The ZPMs were packed into a mini-column for on-line solid-phase extraction (SPE) of the above metal ions. Following extraction with 40 mM NH₄NO₃ and 0.5 M HNO₃ solution, the ions were quantified by ICP-MS. Under the optimized conditions, the enrichment factors (from a 40 mL sample) are up to 60 for the ions V(V), As(III), Sb(III) and Hg(II), and 55 for Cr(III) and Sn(IV). The detection limits are 1.2, 3.4, 1.0, 3.7, 2.1 and 1.6 ng L^?1 for V(V), Cr(III), As(III), Sn(IV), Sb(III) and Hg(II), respectively, and the relative standard deviations (RSDs) are below 5.2%. The feasibility and accuracy of the method were validated by successfully analyzing six certified reference materials as well as lake, well and river waters.

Open image in new window

Graphical abstract Zwitterion-functionalized polymer microspheres (ZPMs) were prepared and packed into a mini-column for on-line solid-phase extraction (SPE) via pump 1. Then V(V), Cr(III), As(III), Sn(IV), Sb(III) and Hg(II) ions in environmental waters were eluted and submitted to ICP-MS via pump 2.

     

Rapid and selective chelatometric titration of aluminium in non-ferrous alloys

A rapid chelatometric method for the determination of Al (4–20%) in magnesium, copper and chromium-aluminium-iron alloys is proposed. HEDTA is used as titrant and Zn solution as back-titrant, with hydrazidazol as indicator. Mn(II), Cu(II), Cd, Zn, Pb, Co(II), Ni, Hg(II), Fe(III), Bi, Cr(III), Sb(III), Ce(III), La, Sn(IV), Ti(IV), Zr and Mo(VI) do not interfere. High selectivity is achieved by a combination of group separation, masking and interference correction. The coefficient of variation varies from 0.2 to 1%.     

Extraction behavior of Tm(III), Dy(III) and Sm(III) lanthanide with N-benzoyl-N-phenylhydroxalamine

The extraction of Sm(III), Dy(III) and Tm(III) with N-benzoyl-N-phenylhydroxalamine (BPHA) in benzene at pH range (1–10) has been studied. Quantitative separation was found in borate media at pH 8. The slope analysis showed that the extracted complex was M(BPHA)₃, where M=Sm(III), Dy(III) and Tm(III). The effect of various masking agents indicated that EDTA, oxalate, fluoride, phosphate and citrate, interfered in this study. Decontamination study showed that Cu(II), Zn(II), Ni(II), Co(II), Cr(III), Sc(III) and Fe(III) had very poor separation factors, whereas Sn(II), Cd(II), In(III), Ru(II), Hg(II), Ag(I), Ta(V) and Hf(IV) had very large separation factor. The effect of different diluents showed that carbontetrachloride, chloroform, benzene, toluene, nitrobenzene dichloromethane, MIBK and cyclohexanone were equally good for extraction except TBP due to ion association.     

Synthesis and spectroscopic,magnetic and cyclic voltammetric characterization of some metal complexes of methionine: [(C5H10NO2S)2MII]; MII = Mn(II), Co(II), Ni(II), Cu(II), Zn(II), Cd(II) and Hg(II)

Some metal complexes of DL–methionine were prepared in aqueous medium and characterized by different physico-chemical methods. Methionine forms 1:2 complexes with metal, M(II). The general empirical formula of the complexes is proposed as [(C₅H₁₀NO₂S)₂M^II]; where M^II = Mn(II), Co(II), Ni(II), Cu(II), Zn(II), Cd(II) and Hg(II). All the complexes are extremely stable in light and air and optically inactive. Magnetic susceptibility data of the complexes demonstrate that they are high spin paramagnetic complex except Zn(II), Cd(II) and Hg(II) complexes. The bonding pattern in the complexes are similar to each other as indicated by electronic absorption spectra and FTIR spectral analysis. The current potential data, peak separation (AE) and the peak current ratio (i_pa/i_pc) of the (Mn, Cu and Cd) complexes indicate that the charge transfer processes are irreversible, the systems are diffusion controlled and also adsorptive controlled. The charge transfer rate constant of metals in their complexes are less than those in their metal salts at identical experimental conditions due to the coordination of metal with methionine.     

Thermogravimetric analysis of some metal thiocarbonates and sulphides obtained with potassium thiocarbonate (PTC) reagent

The thiocarbonates of K(I), Tl(I), Pb(II), Cd(II), Cu(II), Co(II), Ni(II), Zn(II), Fe(II) and the sulphides of Ag(I), Cu(II), Cd(II), Hg(II), Bi(III), Mo(VI), Pt(IV), Au(III), V(V), Se(IV), Te(IV), As(III, V), Sb(III) have been studied by thermogravimetric analysis. These studies not only confirm the purity of the precipitated products obtained with PTC but also determine correct temperature ranges for the precipitates to attain constant weight, thereby affording gravimetric evaluations of even mg quantities of the metal ions studied. Purity of precipitated products was made possible with the technique of precipitation from homogeneous solution based on the PTC reagent as precipitant.