Degradation of kinetically-stable o/w emulsions

This article summarizes the studies on the degradation of the thermodynamically unstable o/w (nano)emulsion--a dispersion of one liquid in another, where each liquid is immiscible, or poorly miscible in the other. Emulsions are unstable exhibiting flocculation, coalescence, creaming and degradation. The physical degradation of emulsions is due to the spontaneous trend toward a minimal interfacial area between the dispersed phase and the dispersion medium. Minimizing the interfacial area is mainly achieved by two mechanisms: first coagulation possibly followed by coalescence and second by Ostwald ripening. Coalescence is often considered as the most important destabilization mechanism leading to coursing of dispersions and can be prevented by a careful choice of stabilizers. The molecular diffusion of solubilizate (Ostwald ripening), however, will continuously occur as soon as curved interfaces are present. Mass transfers in emulsion may be driven not only by differences in droplet curvatures, but also by differences in their compositions. This is observed when two or more chemically different oils are emulsified separately and the resulting emulsions are mixed. Compositional ripening involves the exchange of oil molecules between emulsion droplets with different compositions. The stability of the electrostatically- and sterically-stabilized dispersions can be controlled by the charge of the electrical double layer and the thickness of the droplet surface layer formed by non-ionic emulsifier. In spite of the similarities between electrostatically- and sterically-stabilized emulsions, there are large differences in the partitioning of molecules of ionic and non-ionic emulsifiers between the oil and water phases and the thickness of the interfacial layers at the droplet surface. The thin interfacial layer (the electrical double layer) at the surface of electrostatically stabilized droplets does not create any steric barrier for mass transfer. This may not be true for the thick interfacial layer formed by non-ionic emulsifier. The interactive sterically-stabilized oil droplets, however, can favor the transfer of materials within the intermediate agglomerates. The stability of electrosterically-stabilized emulsion is controlled by the ratio of the thickness of the non-ionic emulsifier adsorption layer (delta) to the thickness of the electrical double layer (kappa(-1)) around the oil droplets (delta/(kappa(-1))) = (deltakappa). The monomer droplet degradation can be somewhat depressed by transformation of coarse emulsions to nano-emulsion (miniemulsion) by intensive homogenization and by the addition of a surface active agent (coemulsifier) or/and a water-insoluble compound (hydrophobe). The addition of hydrophobe (hexadecane) to the dispersed phase significantly retards the rate of ripening. A long chain alcohol (coemulsifier) resulted in a marked improvement in stability, as well, which was attributed to a specific interaction between alcohol and emulsifier and to the alcohols tendency to concentrate at the o/w interface to form stronger interfacial film. The rate of ripening, according to the Lifshitz-Slyozov-Wagner (LSW) model, is directly proportional to the solubility of the dispersed phase in the dispersion medium. The increased polarity of the dispersed phase (oil) decreases the stability of the emulsion. The molar volume of solubilizate is a further parameter, which influences the stability of emulsion or the transfer of materials through the aqueous phase. The interparticle interaction is expected to favor the transfer of solubilizate located at the interfacial layer. The kinetics of solubilization of non-polar oils by ionic micelles is strongly related to the aqueous solubility of the oil phase (the diffusion approach), whilst their solubilization into non-ionic micelles can be contributed by interparticle collisions.     

Influence of interfacial characteristics on Ostwald ripening in hydrocarbon oil-in-water emulsions

The influence of the nature of the interfacial membrane on the kinetics of droplet growth in hydrocarbon oil-in-water emulsions was investigated. Droplet growth rates were determined by measuring changes in the droplet size distribution of 1 wt % n-tetradecane or n-octadecane oil-in-water emulsions using laser diffraction. The interfacial properties of the droplets were manipulated by coating them with either an SDS layer or with an SDS-chitosan layer using an electrostatic deposition method. The emulsion containing SDS-coated octadecane droplets did not exhibit droplet growth during storage for 400 h, which showed that it was stable to Ostwald ripening because of this oils extremely low water-solubility. The emulsion containing SDS-coated n-tetradecane droplets showed a considerable increase in mean droplet size with time, which was attributed to Ostwald ripening associated with this oils appreciable water-solubility. On the other hand, an emulsion containing SDS-chitosan coated n-tetradecane droplets was stable to droplet growth, which was attributed to the ability of the interfacial membrane to resist deformation because of its elastic modulus and thickness. This study shows that the stability of emulsion droplets to Ostwald ripening can be improved by using an electrostatic deposition method to form thick elastic membranes around the droplets.     

Effects of emulsifier type and environmental stress on the stability of curcumin emulsion

The objective of this study was to investigate the effects of environmental stress and emulsifier types on the stability of curcumin emulsions. Results showed that Lecithin and Tween 80 presented good emulsifying capacity. The Tween 80 emulsion was the most stable among the four emulsions.

The particle sizes of Tween 80 and whey protein emulsion were relatively smaller than gum arabic and lecithin. Extensive droplet aggregation appeared in whey protein-stabilized emulsions when the pH was approximately isoelectric point (pI) with salt concentration >200?mM. Lecithin emulsion was unstable when pH?≤?6 with salt concentration >100?mM. There was little impact of pH and ionic strength on gum arabic and Tween 80 emulsions. All of the emulsions were stable at temperatures from 30 to 90°C in the absence of salt. These results help characterize the emulsifying and stabilizing abilities of emulsifier types intended for applications in the food industry.     

Spontaneously formed trans-anethol/water/alcohol emulsions: mechanism of formation and stability

We studied the spontaneous emulsification and droplet growth mechanism in trans-anethol/water/ethanol solutions, also known as the beverage ouzo, using dynamic light scattering spectroscopy. This simple ternary mixture is a generic example of a system that forms microemulsions spontaneously when brought into the two-phase region. The volume fraction of the dispersed phase was found to profoundly affect the growth rates of the droplets, which is a new finding that has not been predicted by the Lifshitz-Slyozov-Wagner theory. Time-dependent measurements show that the droplet growth is governed by Ostwald ripening (OR), and no coalescence was observed. Furthermore, the OR rates increase with increasing oil concentration at low alcohol content. We attribute this behavior to enhanced droplet-droplet interactions. At high ethanol concentrations, we found that the measured rates decreased as the oil concentration increased. The OR growth mechanism completely correlates with changes in droplet size. The kinetics of droplet growth shows that the ripening has a saturation limit at a droplet radius of about 1.5 mum. Thus, formed emulsions remain stable for months.     

Stability of Emulsions Containing Both Sodium Caseinate and Tween 20

The creaming and rheology of oil-in-water emulsions (30 vol% n-tetradecane, pH 6.8) stabilized by a mixture of commercial sodium caseinate and the non-ionic emulsifier polyoxyethylene sorbitan monolaurate (Tween 20) has been investigated at 21 degrees C. The presence of sufficient Tween 20 to displace most of the protein from the emulsion droplet surface leads to greatly enhanced emulsion creaming (and strongly non-Newtonian rheology) which is indicative of depletion flocculation by nonadsorbed surface-active material (protein and emulsifier). In emulsions containing a constant amount of surface-active material, the replacement of a very small fraction of Tween 20 by caseinate in a stable pure Tween 20 emulsion leads to enhanced creaming for a small fraction of the droplets, and this fraction increases with increasing replacement of emulsifier by protein. This behavior is probably due to depletion flocculation, although an alternative bridging mechanism is also a possibility. The overall stability of these sets of emulsions can be represented in terms of a global stability diagram containing regions of bridging flocculation and coalescence (low content of surface-active material), stability (intermediate content), and depletion flocculation (high content). Copyright 1999 Academic Press.     

Effect of diutan microbial polysaccharide on the stability and rheological properties of O/W nanoemulsions formed with a blend of Span20-Tween20

The stability and rheological behavior of oil-in-water (O/W) nano-emulsions formed with a blend of Span20-Tween20 have been studied with and without diutan microbial polysaccharide. It is found that there exist thresholds for the water content and emulsifier to obtain stable nano-emulsions using the emulsion inversion phase (EIP) method. The viscosity of the nano-emulsion is proportional to the emulsifier content and inversely proportional to the water content. High emulsifier content is not conducive to the thermal stability of the nano-emulsion. The addition of diutan gum with negative charge into the nano-emulsions increases the electrostatic repulsion between droplets and makes the droplet size smaller and more unifom, slowing down the coalescence and Ostwald ripening of the nano-emulsions. Due to the association of the diutan gum double helix, a three-dimensional network structure is formed in the continuous phase of nano-emulsions, which improves the stability of nano-emulsions and is also the main factor giving the nano-emulsion high viscoelasticity at high temperature. This study offers new insight into the nano-emulsion containing microbial polysaccharide and may serve as a guideline for practical applications of new nano-emulsion systems.     

Effect of Emulsifier Type on the Characterization of O/W Emulsions Using a Spectroscopy Technique

The droplet size distribution (DSD) of emulsions is the result of two competitive effects that take place during emulsification process, i.e., drop breakup and drop coalescence, and it is influenced by the formulation and composition variables, i.e., nature and amount of emulsifier, mixing characteristics, and emulsion preparation, all of which affect the emulsion stability. The aim of this study is to characterize oil-in-water (O/W) emulsions (droplet size and stability) in terms of surfactant concentration and surfactant composition (sodium dodecyl benzene sulphonate (SDBS)/Tween 80 mixture). Ultraviolet-visible (UV-vis) transmission spectroscopy has been applied to obtain droplet size and stability of the emulsions and the verification of emulsion stability with the relative cleared volume technique (time required for a certain amount of emulsion to separate as a cleared phase). It is demonstrated that the DSD of the emulsions is a function of the oil concentration and the surfactant composition with higher stability for emulsions prepared with higher SDBS ratio and lower relative cleared volume with the time. Results also show that smaller oil droplets are generated with increasing Tween 80 ratio and emulsifier concentration.     

Solubilization in monodisperse emulsions

The kinetics of oil solubilization into micelles from nearly monodisperse alkane-in-water emulsion droplets was investigated. Emulsions containing either hexadecane or tetradecane oils were fractionated to be narrowly distributed, using a method developed by Bibette [J. Bibette, J. Colloid Interface Sci. 147 (1991) 474]. These monodisperse emulsions were mixed with SDS or Tween 20 aqueous micellar solutions of various concentrations. Time-dependent solubilization was monitored using light scattering and a decrease in average droplet size over time was observed, in contrast to what has been observed previously with polydisperse emulsions. The rate at which the droplet size decreased was found to be independent of the initial droplet size. Turbidity measurements were also used to track the solubilization kinetics, and a population balance analysis used on both types of measurements to extract effective mass transfer coefficients. The dependence of these transfer coefficients on droplet size, alkane type, surfactant type and concentration provide insights into plausible mechanisms of emulsion droplet solubilization within micellar solutions.     

Influence of droplet characteristics on the formation of oil-in-water emulsions stabilized by surfactant-chitosan layers

The objective of this study was to establish the optimum conditions for preparing stable oil-in-water emulsions containing droplets surrounded by surfactant-chitosan layers. A primary emulsion containing small droplets (d32 approximately = 0.3 microm) was prepared by homogenizing 20 wt% corn oil with 80 wt% emulsifier solution (20 mM SDS, 100 mM acetate buffer, pH 3) using a high-pressure valve homogenizer. The primary emulsion was diluted with chitosan solutions to produce secondary emulsions with a range of oil and chitosan concentrations (0.5-10 wt% corn oil, 0-1 wt% chitosan, pH 3). The secondary emulsions were sonicated to help disrupt any droplet aggregates formed during the mixing process. The electrical charge, particle size, and amount of free chitosan in the emulsions were then measured. The droplet charge changed from negative to positive as the amount of chitosan in the emulsions was increased, reaching a relatively constant value (approximately +50 mV) above a critical chitosan concentration (C(Sat)), which indicated that saturation of the droplet surfaces with chitosan occurred. Extremely large droplet aggregates were formed at chitosan concentrations below C(Sat), but stable emulsions could be formed above C(Sat) provided the droplet concentration was not high enough for depletion flocculation to occur. Interestingly, we found that stable multilayer emulsions could also be formed by mixing chitosan with an emulsion stabilized by a nonionic surfactant (Tween 20) due to the fact the initial droplets had some negative charge. The information obtained from this study is useful for preparing emulsions stabilized by multilayer interfacial layers.     

Emulsion Ripening through Molecular Exchange at Droplet Contacts

Two coarsening mechanisms of emulsions are well established: droplet coalescence (fusion of two droplets) and Ostwald ripening (molecular exchange through the continuous phase). Here a third mechanism is identified, contact ripening, which operates through molecular exchange upon droplets collisions. A contrast manipulated small‐angle neutron scattering experiment was performed to isolate contact ripening from coalescence and Ostwald ripening. A kinetic study was conducted, using dynamic light scattering and monodisperse nanoemulsions, to obtain the exchange key parameters. Decreasing the concentration or adding ionic repulsions between droplets hinders contact ripening by decreasing the collision frequency. Using long surfactant chains and well‐hydrated heads inhibits contact ripening by hindering fluctuations in the film. Contact ripening can be controlled by these parameters, which is essential for both emulsion formulation and delivery of hydrophobic ingredients.     

Effect of Ionic Strength of Dispersed Phase on Ostwald Ripening in Water-in-Oil Emulsions

Water-in-oil emulsions with a low electrolyte content in the internal phase are unstable with respect to Ostwald ripening. The main components of the total pressure acting on the surface of internal phase droplets are considered. The equilibrium values of the diameters of dispersed phase droplets are calculated. The dependences of the difference in the osmotic and Laplace pressures on the droplet size and electrolyte concentration in the droplets are obtained. It is shown that, at the electrolyte concentration below the critical value, the number of droplets in emulsion decreases. If the concentration is above the critical value, water diffuses from small to large droplets, but their number remains unchanged. The change in NaCl concentration in the droplets of internal phase of polydisperse emulsion during the Ostwald ripening is calculated. The results of calculations correlate with the experimental data on the stability of emulsions with respect to coalescence and sedimentation.     

Impact of oil type on nanoemulsion formation and Ostwald ripening stability

The formation of stable transparent nanoemulsions poses two challenges: the ability to initially create an emulsion where the entire droplet size distribution is below 80 nm, and the subsequent stabilization of this emulsion against Ostwald ripening. The physical properties of the oil phase and the nature of the surfactant layer were found to have a considerable impact on nanoemulsion formation and stabilization. Nanoemulsions made with high viscosity oils, such as long chain triglycerides (LCT), were considerably larger ( D = 120 nm) than nanoemulsions prepared with low viscosity oils such as hexadecane ( D = 80 nm). The optimization of surfactant architecture, and differential viscosity eta D/eta C, has led to the formation of remarkably small nanoemulsions. With average sizes below 40 nm they are some of the smallest homogenized emulsions ever reported. What is more remarkable is that LCT nanoemulsions do not undergo Ostwald ripening and are physically stable for over 3 months. Ostwald ripening is prevented by the large molar volume of long chain triglyceride oils, which makes them insoluble in water thus providing a kinetic barrier to Ostwald ripening. Examination of the Ostwald ripening of mixed oil nanoemulsions found that the entropy gain associated with oil demixing provided a thermodynamic barrier to Ostwald ripening. Not only are the nanoemulsions created in this work some of the smallest reported, but they are also thermodynamically stable to Ostwald ripening when at least 50% of the oil phase is an insoluble triglyceride.     

Influence of interfacial properties on Ostwald ripening in crosslinked multilayered oil-in-water emulsions

The influence of interfacial crosslinking, layer thickness and layer density on the kinetics of Ostwald ripening in multilayered emulsions at different temperatures was investigated. Growth rates of droplets were measured by monitoring changes in the droplet size distributions of 0.5% (w/w) n-octane, n-decane, and n-dodecane oil-in-water emulsions using static light scattering. Lifshitz-Slyozov-Wagner theory was used to calculate Ostwald ripening rates. A sequential two step process, based on electrostatic deposition of sugar beet pectin onto fish gelatin or whey protein isolate (WPI) interfacial membranes, was used to manipulate the interfacial properties of the oil droplets. Laccase was added to the fish gelatin-beet pectin emulsions to promote crosslinking of adsorbed pectin molecules via ferulic acid groups, whereas heat was induced to promote crosslinking of WPI and helix coil transitions of fish gelatin. Ripening rates of single-layered, double-layered and crosslinked emulsions increased as the chain length of the n-alkanes decreased. Emulsions containing crosslinked fish gelatin-beet pectin coated droplets had lower droplet growth rates (3.1 ± 0.3 × 10⁻²⁶ m³/s) than fish gelatin-stabilized droplets (7.3 ± 0.2 × 10⁻²⁶ m³/s), which was attributed to the formation of a protective network. Results suggest that physical or enzymatic biopolymer-crosslinking of interfaces may reduce the molecular transport of alkanes between the droplets in the continuous phase.     

Modulation of emulsion rheology through electrostatic heteroaggregation of oppositely charged lipid droplets: influence of particle size and emulsifier content

The influence of electrostatically-induced heteroaggregation of oppositely charged lipid droplets on the rheology and stability of emulsions has been studied. 20 wt.% oil-in-water emulsions (pH 6) containing oppositely charged droplets were fabricated by mixing cationic lactoferrin-coated lipid droplets with anionic β-lactoglobulin-coated lipid droplets. Emulsions containing mixtures of droplets with different charges (positive or negative) and sizes (large or small) were prepared, and then their overall particle characteristics (ζ-potential and size) and rheology were measured. Emulsions formed by mixing positive droplets and negative droplets that were both relatively small (d(43) ≈ 0.3 μm) exhibited extensive flocculation and had paste-like properties at intermediate positive-to-negative particle ratios. On the other hand, emulsions formed by mixing positive droplets and negative droplets that were both relatively large (d(43) ≈ 3 μm) exhibited little aggregation and had relatively low viscosities at all particle ratios. Emulsions with small negative droplets and large positive droplets (or vice versa), exhibited some aggregation and viscosity enhancement at intermediate particle ratios. The presence of relatively high levels of protein in the aqueous phase of mixed emulsions reduced the level of droplet aggregation and viscosity enhancement observed, which was attributed to the ability of protein molecules to bind to droplet surfaces and neutralize their charges. Electrostatically-induced heteroaggregation of lipid droplets may be a useful means of controlling the physicochemical properties of emulsion-based products in the food, personal care, pharmaceutical and cosmetic industries.     

The life of an anise-flavored alcoholic beverage: does its stability cloud or confirm theory?

The well-known alcoholic beverage Pastis becomes turbid when mixed with water due to the poor solubility of trans-anethol, the anise-flavored component of Pastis in the water solution formed. This destabilization appears as the formation of micrometer-sized droplets that only very slowly grow in size, thus expanding the life of the anise-flavored beverage. The slow growth has been attributed to an extremely low interfacial tension of the droplets. Fitting experimental droplet growth rates to an Ostwald ripening model, interfacial tensions were deduced in the past. Direct determination of the interfacial tensions was not yet reported on these systems. We have measured the interfacial tensions and used these data to predict droplet growth rates using an Ostwald ripening model and a model for creaming of the droplets. The interfacial tension was measured to be about 11 mN/m for a 30/70 w/w % ethanol/water mixture, and it decreases slightly to a value of 1.4 mN/m in the case of a 70/30 w/w % ethanol/water mixture. These values are not as low as those deduced in the past. The theoretical predictions for both the Ostwald ripening rates and the creaming rates, using the directly measured interfacial tensions, are found to contradict with the experimental results on Ostwald ripening and creaming. While the experiments on Ostwald ripening show an increase in stability with increasing ethanol concentration, the results based on our interfacial tension measurements in combination with the same Ostwald ripening model show a decrease in stability with an increase in ethanol concentration. Further research is needed to understand fully which parameters play a role in both droplet growth and the stability of these three-component emulsions to elucidate the current discrepancy between model and experiment. This could be useful for a better control of "spontaneous emulsification" processes.     

Ostwald ripening of oil-in-water emulsions stabilized by phenoxy-substituted dextrans

The stability of oil-in-water emulsions prepared using dextran, a natural polysaccharide, hydrophobically substituted with phenoxy groups, was studied. The evolution of the emulsion droplet size was investigated as a function of polymer concentration (Cp=0.2 to 1% w/w in a water phase) and the degree of phenoxy substitution (tau=4.2 to 15.7%). For the highest tau values, emulsions, which presented submicrometer droplets, were stable over more than 4 months at room temperature. The most substituted polymers clearly showed a better efficiency to lower the surface tension at the oil/water interface. DexP did not induce real viscosification of the continuous phase. The linearity of the particle volume variation with time, and the invariability of the volume distribution function, proved that Ostwald ripening was the main destabilization mechanism of the phenoxy dextran emulsions. The nature of the oil dispersed phase drastically affected the behavior of emulsions. While the emulsions prepared with n-dodecane presented a particle growth with time, only few size variations occurred when n-hexadecane was used. Furthermore, small ratios of n-hexadecane in n-dodecane phase reduced the particle growth due to the lower solubility and lower diffusion coefficient in water of n-hexadecane, which acted as a ripening inhibitor.     

Effect of molecular weight and degree of deacetylation of chitosan on the formation of oil-in-water emulsions stabilized by surfactant-chitosan membranes

The objective of this study was to establish the influence of polyelectrolyte characteristics (molecular weight and charge density) on the properties of oil-in-water emulsions containing oil droplets surrounded by surfactant-polyelectrolyte layers. A surfactant-stabilized emulsion containing small droplets (d32 approximately 0.3 microm) was prepared by homogenizing 20 wt% corn oil with 80 wt% emulsifier solution (20 mM SDS or 2.5 wt% Tween 20, 100 mM acetate buffer, pH 3) using a high-pressure valve homogenizer. This primary emulsion was then diluted with various chitosan solutions to produce secondary emulsions with a range of chitosan concentrations (3 wt% corn oil, 0-1 wt% chitosan). The influence of the molecular characteristics of chitosan on the properties of these emulsions was examined by using chitosan ingredients with different molecular weights (MW approximately 15, 145, and 200 kDa) and degree of deacetylation (DDA approximately 40, 77, and 92%). The electrical charge and particle size of the secondary emulsions were then measured. Extensive droplet aggregation occurred when the chitosan concentration was below the amount required to saturate the droplet surfaces, but stable emulsions could be formed at higher chitosan concentrations. The zeta-potential and mean diameter (d32) of the particles in the secondary emulsions was not strongly influenced by chitosan MW, however the chitosan with the lowest DDA (40%) produced droplets with smaller mean diameters and zeta-potentials than the other two DDA samples examined. Interestingly, we found that stable multilayer emulsions could be formed by mixing medium or high MW chitosan with an emulsion stabilized by a non-ionic surfactant (Tween 20) due to the fact the initial droplets had some negative charge. The information obtained from this study is useful for preparing emulsions stabilized by multilayer interfacial layers.     

Amphiphilic polysaccharides: useful tools for the preparation of nanoparticles with controlled surface characteristics

Polymeric surfactants obtained by hydrophobic modification of dextran are used as stabilizers for oil-in-water emulsions. The kinetics of interfacial tension decrease is studied as a function of polymer structural characteristics (degree of hydrophobic substitution) and at various polymer concentrations. Several hydrocarbon oils, either aliphatic (octane, decane, dodecane, and hexadecane) or aromatic (styrene), are tested. Kinetics exhibits the same general trends no matter which oil or polymer is considered. The emulsifying properties of the polymeric surfactants are illustrated by the preparation of oil-in-water emulsions. The droplet size at the preparation is correlated to the amount of oil and to the polymer concentration in the aqueous phase. For low polymer/oil ratios, it is shown that the droplet size is limited by the initial amount of polymer. On the contrary, for high polymer/oil ratios, the droplet size seems to level down, indicating that other parameters become predominant. Emulsion aging occurs by Ostwald ripening, and it is demonstrated that the theoretical equation of Lifshitz, Slyozov, and Wagner (LSW) correctly describes the experimental results. The nature of the oil has important effects on emulsion aging, as described by the LSW equation. The aging of emulsions containing oil mixtures is quantitatively described on the basis of the results with pure oils. The influence of polymer chemical structure can be conveniently correlated to interfacial tension results through the LSW equation. On the contrary, the influence of oil volume fraction seems to be overestimated by the usual correction factor, k(phi). The effect of temperature on emulsion aging is finally examined. Miniemulsions stabilized with dextran derivatives are used for the radical polymerization of styrene. Following this procedure, polysaccharide-covered polystyrene nanoparticles are prepared and characterized (size and surface coverage). The size of the particles is directly correlated to that of the initial droplets for styrene volume fractions around 10%. On the contrary, for initial styrene volume fractions around 20%, particles exhibit a larger size than the initial droplets, indicating that coalescence processes take place during polymerization. The amount of dextran at the surface of the particles is determined and compared to the adsorbed amounts resulting from emulsion preparation.     

Evolution of droplet size distribution and composition in miniemulsions

A fundamental understanding of the formation, degradation and polymerization of miniemulsions has been hindered by difficulties in quantifying their monomer droplet size distribution (DSD). In this work, particle sizing techniques including capillary hydrodynamic fractionation, acoustic attenuation spectroscopy, surfactant titration, and microscopy were adapted to characterize miniemulsion DSDs. The key ingredient in miniemulsions is the costabilizer, a low water solubility compound that limits monomer diffusion from the smaller to larger droplets (Ostwald ripening). The DSD evolution of styrene miniemulsions employing hexadecane (HD) as costabilizer was characterized. With less costabilizer, droplets were initially smaller, but increased in average size with time, and their DSDs broadened. These changes were slowed with addition of extra surfactant after homogenization. After several days, the average droplet size increased to about 150 nm regardless of the amount of HD or surfactant used. The HD content of separated portions of centrifuged miniemulsions was measured and showed significant Ostwald ripening within minutes after preparation. The further evolution of the DSD is attributed primarily to droplet coalescence. Less composition change occurred with either higher HD content or post‐homogenization surfactant addition, both of which led to minimization of free energy, increasing stability. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1529–1544     

Water-in-carbon dioxide emulsions stabilized with hydrophobic silica particles

W/C emulsions were stabilized using hydrophobic silica particles adsorbed at the interface, resulting in average droplet diameters as low as 7.5 microm. A porous cross-linked shell was formed about a hydrophilic (colloidal and fumed) silica core with a trifunctional silylating agent, (heptadecafluoro-1,1,2,2-tetrahydrodecyl)triethyoxysilane, to render the particles CO(2)-philic. The stability of emulsions comprising equal weights of CO(2) and water was assessed with visual observations of settling fronts and the degree of emulsion coalescence, and the average drop size was measured by optical microscopy. The effect of CO(2) density on both emulsion stability and droplet size was determined quantitatively. The major destabilizing mechanism of the emulsions was settling, whereas Ostwald ripening and coalescence were not visible at any density, even over 7 days. Flocculation of the settling droplets did not occur, although gelation of the emulsions through particle interactions resulted after longer periods of time. CO(2)-philic particles offer a new route to highly stable W/C emulsions, with particle energies of attachment on the order of 10(6)kT, even at CO(2) densities as low as 0.78 g ml(-1). At these low densities, surfactants rarely stabilize emulsions as the result of poor surfactant tail solvation.