Polymerization of Acrylamide in Aqueous Solution of Poly(N‐isopropylacrylamide) at Lower Critical Solution Temperature

Acrylamide (AAm) was found to polymerize in a solution of poly(N‐isopropylacrylamide) (PNIPAAm) in water at around its lower critical solution temperature (LCST) (32°C) without any initiators. This phenomenon was specifically observed in aqueous solutions of the polymers having LCST such as PNIPAAm and poly(methylvinylether) (PMVE). AAm polymerized only when PNIPAAm and AAm were dissolved in water below LCST of PNIPAAm and then the solution was warmed up to the polymerization temperature (40°C). On the other hand, the polymerization of AAm did not proceed when AAm was added into aqueous PNIPAAm solution during and after the phase separation above 32°C. Furthermore the polymerizability of AAm was remarkably affected by the concentration and molecular weight of the PNIPAAm additives. Under the condition of lower PNIPAAm concentration (0.30 mol/L), the increase in the molecular weight of PNIPAAm considerably increased the molecular weight of the resulting PAAm but decreased the yield of PAAm. Under the condition of higher PNIPAAm concentration (0.60 mol/L) the polymerizability was not so affected by the molecular weight of PNIPAAm, while the molecular weight of PAAm formed by using higher molecular weight PNIPAAm was higher than those of PAAm formed by using lower molecular weight PNIPAAm. Moreover, the molecular weight of PAAm formed by the PNIPAAm induced polymerization of AAm was much higher than that of the polymer obtained by the radical polymerization using AIBN in THF or VA‐ 061 in water.     

Preparation and Characterization of Thermosensitive Nanoparticles for Targeted Drug Delivery

In this study, we have reported novel thermosensitive nanoparticles formulated by an emulsion-solvent evaporation technique using acetaminophen (AAP) as a model drug. The high entrapment efficiency of nanoparticles was 68.56%, particle size about 240.6 nm and zeta potential ?27 mV. Furthermore, the drug release was also investigated both at 37°C and 42°C, respectively. The goal of our study was to obtain a targeted drug delivery system, exploiting the temperature-sensitive behavior. In contrary to normal temperature (37°C), the release rate of AAP was found to noticeably increase at high temperature (42°C) with a larger cumulative amount of drug released. In this way, it would lead to production of nanoparticles having a high thermosensitive behavior on drug release. Thus, this new strategy has the potential to control drug release at the diseased site for targeted drug delivery system (TDDS) with positive temperature-controlled.     

Thermosensitive properties of poly(amidoamine) dendrimers with peripheral phenylalanine residues

Dendrimers are unique polymers with globular shapes and well-defined structures. We previously prepared poly(amidoamine) (PAMAM) dendrimers having phenylalanine (Phe) residues at every chain end of the dendrimer as efficient gene carriers. In this study, we found that Phe-derivatized PAMAM dendrimers change their water solubility depending on temperature. The dendrimers were soluble in aqueous solutions at low temperatures, but they became water-insoluble at temperatures above a specific threshold, which is termed the lower critical solution temperature (LCST). Although the LCST of Phe-modified dendrimers decreased with increasing dendrimer generation, these dendrimers exhibited an LCST of 20-30 degrees C under physiological conditions. In addition, the LCST of the dendrimers was controlled by introducing isoleucine (Ile) residues at chain ends of dendrimers at varying ratios with respect to Phe residues. The PAMAM dendrimers are known to encapsulate various drug molecules. For these reasons, temperature-sensitive dendrimers might be useful as efficient drug carriers with controlled size and temperature-responsive properties.     

温度敏感型树枝状大分子衍生物的合成及药物控制释放

通过加入偶联剂活化末端羧基基团进行酰胺化反应, 将得到的带有羧基末端基团的温敏性聚N-异丙基丙烯酰胺接枝到整代的树枝状大分子聚酰胺-胺(PAMAM)上, 制备了树枝状大分子衍生物PAMAM-g-PNIPAm, 通过FTIR和¹H NMR表征其结构, 通过GPC和¹H NMR测定其分子量, 从而验证了接枝产物的形成; 通过紫外-可见分光光度计测定其在不同pH值缓冲液中的低临界溶胀/溶解温度(LCST)值, 发现产物的LCST值受缓冲液pH值的影响很大, 接枝前后的LCST值也发生了变化. 选用难溶性药物吲哚美辛作为模型药物, 考察了树枝状大分子及其温度敏感性衍生物PAMAM-g-PNIPAm作为载体对药物的包载、增溶和不同温度环境下的释放行为. 结果表明, 树枝状大分子衍生物对吲哚美辛具有增溶和控制释放的性能, 在难溶性药物的控制释放领域具有广阔的应用前景.     

Self-assembled liposomes from electrosprayed polymer-based microparticles

Composite poly(N-isopropylacrylamide) (PNIPAAm)/phosphatidylcholine (PC) microparticles were prepared by electrospraying. PC-based liposomes were subsequently generated upon the addition of water. The microparticles have an average diameter of ca. 1 μm, while the liposomes produced were found to have much smaller diameters of ca. 225–280 nm. The liposomes had zeta potentials of ?44 to ?50 mV, consistent with the formation of a stable suspension. Upon heat treatment, the liposomes exhibit phase transitions due to the influence of PNIPAAm. The liposomes containing 33 % PC have a phase transition temperature of approximately 36 °C, close to physiological conditions. The model drug ketoprofen could be loaded into electrosprayed microparticles and subsequently incorporated into self-assembled liposomes, with an entrapment efficiency for the latter process of ca. 75 %. Sustained drug release regulated by temperature was observed from these drug-loaded materials. At 25 °C, only 45 % of the total drug loading was released after 110 hours, while at 37 °C drug release approached 90 % over the same time period. The self-assembled liposomes reported here, therefore, have great potential as drug delivery devices.     

Temperature and pH dual stimuli responsive PCL‐b‐PNIPAAm block copolymer assemblies and the cargo release studies

A new atom transfer radical polymerization (ATRP) initiator, namely, 2‐(1‐(2‐azidoethoxy)ethoxy)ethyl 2‐bromo‐2‐methylpropanoate containing both “cleavable” acetal linkage and “clickable” azido group was synthesized. Well‐defined azido‐terminated poly(N‐isopropylacrylamide)s (PNIPAAm‐N₃)s with molecular weights and dispersity in the range 11,000–19,000 g mol^?1 and 1.20–1.28, respectively, were synthesized employing the initiator by ATRP. Acetal containing PCL‐b‐PNIPAAm block copolymer was obtained by alkyne–azide click reaction of azido‐terminated PNIPAAm‐N₃ with propargyl‐terminated PCL. Critical aggregation concentration (CAC) of PCL‐b‐PNIPAAm copolymer in aqueous solution was found to be 8.99 × 10^?6 M. Lower critical solution temperature (LCST) of PCL‐b‐PNIPAAm copolymer was found to be 32 °C which was lower than that of the precursor PNIPAAm‐N₃ (36.4 °C). The effect of dual stimuli viz . temperature and pH on size and morphology of the assemblies of PCL‐b‐PNIPAAm block copolymer revealed that the copolymer below LCST assembled in spherical micelles which subsequently transformed to unstable vesicles above the LCST. Heating these assemblies above 40 °C led to the precipitation of PCL‐b‐PNIPAAm block copolymer. Whereas, at decreased pH, micelles of PCL‐b‐PNIPAAm copolymer disintegrate due to the cleavage of acetal linkage and precipitation of hydrophobic hydroxyl‐terminated PCL. The encapsulated pyrene release kinetics from the micelles of synthesized PCL‐b‐PNIPAAm copolymer was found to be faster at higher temperature and at lower pH. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 1383–1396     

Novel poly(N‐isopropylacrylamide)/clay/poly(acrylamide) IPN hydrogels with the response rate and drug release controlled by clay content

Novel interpenetrating network (IPN) hydrogels (PNIPAAm/clay/PAAm hydrogels) based on poly(N‐isopropylacrylamide) (PNIPAAm) crosslinked by inorganic clay and poly(acrylamide) (PAAm) crosslinked by organic crosslinker were prepared in situ by ultraviolet (UV) irradiation polymerization. The effects of clay content on temperature dependence of equilibrium swelling ratio, deswelling behavior, thermal behavior, and the interior morphology of resultant IPN hydrogels were investigated with the help of Fourier transform infrared spectroscopy, differential scanning calorimeter (DSC), scanning electron microscope (SEM). Study on temperature dependence of equilibrium swelling ratio showed that all IPN hydrogels exhibited temperature‐sensitivity. DSC further revealed that the temperature‐sensitivity was weakened with increasing amount of clay. Study on deswelling behavior revealed that IPN hydrogels had much faster response rate when comparing with PNIPAAm/clay hydrogels, and the response rate of IPN hydrogels could be controlled by clay content. SEM revealed that there existed difference in the interior morphology of IPN hydrogels between 20 [below lower critical solution temperature (LCST)] and 50 °C (above LCST), and this difference would become obvious with a decrease in clay content. For the standpoint of applications, oscillating swelling/deswelling behavior was investigated to determine whether properties of IPN hydrogels would be stable for potential applications. Bovine serum albumin (BSA) was used as model drug for in vitro experiment, the release data suggested that the controlled drug release could be achieved by modulating clay content. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 96–106, 2009     

Water affinity and permeability in membranes of alginate-Ca2+ containing poly(n-isopropylacrylamide)

Hydrogels based on semi-interpenetrating network (semi-IPN) combining alginate-Ca²⁺ (matrix) with poly(N-isopropyl acrylamide) (PNIPAAm) were prepared and characterized in order to determine their affinity to water and their permeability to orange II as a function of temperature. Membranes of these hydrogels were obtained by gelation of the aqueous solution of alginate and PNIPAAm by the addition of CaCl₂. The presence of PNIPAAm chains inside the hydrogels alters the water affinity when compared to the pure alginate-Ca²⁺ hydrogels. Although the water uptake capability decreases above 32 °C (Low Critical Solution Temperature (LCST) of PNIPAAm in water), no shrinking of the semi-IPN hydrogels during the phase separation of the PNIPAAm was observed. The permeability of orange II as a function of temperature decreases at 32 °C and shows a dependence on the molar mass of the alginate. The partition coefficient of orange II in the hydrogel membrane, relative to water, decreases by increasing the temperature and its permeability follows a similar behavior. It was proposed that above the LCST of PNIPAAm the Alginate-Ca²⁺ networks mechanically support the collapsed PNIPAAm chains and the diffusion of orange II is minimized. The collapsing process may be followed by the formation of a complex between the carboxylic side groups of alginate and –NH–R groups of PNIPAAm. It would expose the isopropyl groups of PNIPAAm chains, providing a hydrophobic environment that minimizes the interaction between the dye and the polymeric matrix.     

Hybrid alginate beads with thermal‐responsive gates for smart drug delivery

Polysaccharide‐based thermo‐responsive material was prepared by grafting PNIPAAm onto hybrid alginate beads, in which a biomineralized polyelectrolyte layer was constructed aiming to enhance the mechanical strength and ensure higher graft efficiency. XPS results demonstrated that the incorporation of PNIPAAm to the hybrid beads was successful, and the PNIPAAm‐grafted beads were more hydrophilic than the ungrafted ones as indicated by their swelling behavior. The drug release behaviors revealed that the grafted beads were both thermo‐ and pH‐sensitive, and the PNIPAAm existed in the pores of the alginate beads acted as the “on–off” gates: the pores of the beads were covered by the stretched PNIPAAm to delay the drug release at 25°C and opened to accelerate the drug release at 37°C because of the shrinking of PNIPAAm molecules. This paper would be a useful example of grafting thermo‐responsive polymers onto biodegradable natural polymer substrate. The obtained beads provide a new mode of behavior for thermo‐responsive “smart” polysaccharide materials, which is highly attractive for targeting drug delivery system and chemical separation. Copyright © 2010 John Wiley & Sons, Ltd.     

Preparation and Characterization of Temperature-responsive Porous Monoliths

A new temperature‐responsive porous monolith has been prepared by surface‐initiated activators generated by electron transfer atom transfer radical polymerization (AGET ATRP) grafting poly(N‐isopropylacrylamide) (PNIPAAm) within the pores of the porous polymer monolith. The grafting copolymerization was carried out by a method based on a continuous flow‐through technique without special deoxygenation procedure needed in the general ATRP. The addition of ascorbic acid could counteract the oxidation effect of oxygen diffusing into the reaction system. The resulting grafted monolith was characterized by a mercury intrusion method and the size of macropore was 3.65 µm, which was suitable for flow through the monolith for HPLC. The thermally responsive property of the grafted monolith was evaluated by HPLC using steroids with various hydrophobicities as probes. Through determination of retention factor of each steroid on the grafted monolith at different temperatures using water as mobile phase, it was found that the slope of the plot of retention factor of each steroid versus the temperature changed around the low critical solution temperature (LCST, 32°C) of PNIPAAm in water. It was relative to the grafted PNIPAAm temperature sensitivity that a hydrophobic and hydrophilic alternation would take place around its LCST. Based on this thermally responsive property, the grafted monolith was used as stationary phase for HPLC and to separate the steroids using water as mobile phase by changing the column temperature. As a mobile phase, water is much better than organic solvents concerning the environment.     

Synthesis and applications of shell cross-linked thermoresponsive hybrid micelles based on poly(N-isopropylacrylamide-co-3-(trimethoxysilyl)propyl methacrylate)-b-poly(methyl methacrylate)

Shell cross-linked (SCL) thermoresponsive hybrid micelles consisting of a cross-linked thermoresponsive hybrid hydrophilic shell and a hydrophobic core domain were synthesized from poly(N-isopropylacrylamide-co-3- (trimethoxysilyl)propyl methacrylate)-b-polymethyl methacrylate (P(NIPAAm-co-MPMA)-b-PMMA) amphiphilic block copolymers. Transmission electron microscopy (TEM) images showed that the SCL micelles formed regularly globular nanoparticles. The SCL micelles showed reversible dispersion/aggregation in response to temperature cycles through an outer polymer shell lower critical solution temperature (LCST) for PNIPAAm at around 33 degrees C, observed by turbidity measurements and dynamic light scattering (DLS). The drug loading and in vitro drug release properties of the SCL micelles bearing a silica-reinforced PNIPAAm shell were further studied, which showed that the SCL micelles exhibited a much improved entrapment efficiency (EE) as well as a slower release rate which allowed the entrapped molecules to be slowly released over a much longer period of time as compared with pure PNIPAAm-b-PMMA micelles.     

A helical flow, circular microreactor for separating and enriching "smart" polymer-antibody capture reagents

We report a mechanistic study of how flow and recirculation in a microreactor can be used to optimize the capture and release of stimuli-responsive polymer-protein reagents on stimuli-responsive polymer-grafted channel surfaces. Poly(N-isopropylacrylamide) (PNIPAAm) was grafted to polydimethylsiloxane (PDMS) channel walls, creating switchable surfaces where PNIPAAm-protein conjugates would adhere at temperatures above the lower critical solution temperature (LCST) and released below the LCST. A PNIPAAm-streptavidin conjugate that can capture biotinylated antibody-antigen targets was first characterized. The conjugate's immobilization and release were limited by mass transport to and from the functionalized PNIPAAm surface. Transport and adsorption efficiencies were dependent on the aggregate size of the PNIPAAm-streptavidin conjugate above the LCST and also were dependent on whether the conjugates were heated in the presence of the stimuli-responsive surface or pre-aggregated and then flowed across the surface. As conjugate size increased, through the addition of non-conjugated PNIPAAm, recirculation and mixing were shown to markedly improve conjugate immobilization compared to diffusion alone. Under optimized conditions of flow and reagent concentrations, approximately 60% of the streptavidin conjugate bolus could be captured at the surface and subsequently successfully released. The kinetic release profile sharpness was also strongly improved with recirculation and helical mixing. Finally, the concentration of protein-polymer conjugates could be achieved by continuous conjugate flow into the heated recirculator, allowing nearly linear enrichment of the conjugate reagent from larger volumes. This capability was shown with anti-p24 HIV monoclonal antibody reagents that were enriched over 5-fold using this protocol. These studies provide insight into the mechanism of smart polymer-protein conjugate capture and release in grafted channels and show the potential of this purification and enrichment module for processing diagnostic samples.     

Synthesis and characterization of novel thermoresponsive‐co‐biodegradable hydrogels composed of N‐isopropylacrylamide,poly(L‐lactic acid), and dextran

A series of novel multifunctional hydrogels that combined the merits of both thermoresponsive and biodegradable polymeric materials were designed, synthesized, and characterized. The hydrogels were copolymeric networks composed of N‐isopropylacrylamide (NIPAAM) as a thermoresponsive component, poly(L‐lactic acid) (PLLA) as a hydrolytically degradable and hydrophobic component, and dextran as an enzymatically degradable and hydrophilic component. The chemical structures of the hydrogels were characterized by an attenuated total reflection–Fourier transform infrared spectroscopy (ATR–FTIR) technique. The hydrogels were thermoresponsive, showing a lower critical solution temperature (LCST) at approximately 32 °C, and their swelling properties strongly depended on temperature changes, the balance of the hydrophilic/hydrophobic components, and the degradation of the PLLA component. The degradation of the hydrogels caused by hydrolytic cleavage of ester bonds in the PLLA component was faster at 25 °C below the LCST than at 37 °C above the LCST, determined by the ATR–FTIR technique. Due to their multifunctional properties, the designed hydrogels show great potential for biomedical applications, including drug delivery and tissue engineering. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5054–5066, 2004     

Interactions between temperature-sensitive hydrogel microspheres and granulocytes

Poly(N-isopropylacrylamide) (PNIPAM) has a low critical solution temperature (LCST) at 32°C in water and the hydrophilicity changes through the LCST. The microspheres whose surface was composed of PNIPAM exhibited phase transition behavior around 32°C. Therefore, the interactions between PNIPAM micropheres and granulocytes depended on the temperature. That is, the oxygen consumption and active oxygen production by cells in contact with PNIPAM-containing microspheres and adhesion of the microspheres to the cell surface were more enhanced above the LCST of PNIPAM than below it, whereas no significant temperature dependence of cell–microspheres interaction was observed in nonthermosensitive microsphere systems. It was suggested that the function of cells could be controlled with temperature using the temperature-sensitive microspheres.     

Grafting of temperature sensitive PNIPAAm on hydrophilised polysulfone UF membranes

Poly(N-isopropyl acrylamide) (PNIPAAm) was grafted on a polysulfone UF membrane. The changes of permeability as well as retention of PEG (35 kg/mol) and Dextran (500 kg/mol) between 23 and 60 °C were determined for both grafted and unmodified membranes. The results showed that the viscosity corrected water permeability and solute retention were almost constant for the unmodified membranes within the measured temperature range, the permeability of the grafted membranes increased and the retention of Dextran and PEG decreased with temperature. The variation of changes was most obvious in the temperature range 27–37 °C for the modified membranes due to the lower critical solution temperature (LCST) of PNIPAAm. The location and profile of PNIPAAm inside and on the surface of the membrane were analysed by SEM and FTIR. Depth profile calculation for FTIR spectra showed that PNIPAAm was mostly placed inside the membrane (at a depth of 1.06–1.10 μm from the surface) rather than on the surface. The amount of grafted PNIPAAm was low and did not significantly affect the morphology of the membrane. Therefore, a difference in SEM pictures of modified and unmodified membranes could not be seen. The modified membrane exhibited a clearly different thermal response compared to the unmodified one.     

Synthesis,thermo-responsive micellization and caffeine drug release of novel PBMA-<Emphasis Type="Italic">b</Emphasis>-PNIPAAm block polymer brushes

Brush-like block copolymers with poly(t-butyl methacrylate) (PBMA) and poly(N-isopropylacrylamide) (PNIPAAm) as side arms, PBMA-b-PNIPAAm, were designed and synthesized via a simple free radical polymerization route. The chemical structure and molecular weight of these polymer brushes were characterized and determined by nuclear magnetic resonance (¹H NMR), Fourier transform infrared spectrometry (FTIR) and gel permeation chromatography (GPC). The micellar formation by these polymer brushes in aqueous solutions were detected by a surface tension technique, and the critical micelle concentration (CMC) ranged from 1.53 to 8.06 mg L⁻¹. The morphology and geometry of polymer micelles were investigated by transmission electron microscope (TEM) and dynamic light scattering (DLS). The polymer micelles assume the regularly-spherical core-shell structure with well-dispersed individual nanoparticles, and the particle size was in the range from 36 to 93 nm. The PNIPAAm segments exhibited a thermoreversible phase transition, so the resulting block polymer brushes were temperature-sensitive and the low critical solution temperature (LCST) was determined by UV-vis spectrometer at about 28.82–29.40°C. The characteristic parameters of the polymer micelles such as CMC, micellar size and LCST values were affected by their compositional ratios and the length of hydrophilic or hydrophobic chains. The evaluation for caffeine drug release behavior of the block polymer micelles demonstrated that the self-assembled micelles exhibited thermal-triggered properties in controlled drug release.     

Synthesis and properties of thermoresponsive magnetic polymer composites and their electrospun nanofibers

The thermoresponsive magnetic polymer composites and nanofibers were fabricated. Their thermal and magnetic properties were also investigated. Fe₃O₄ nanoparticles were prepared by coprecipitation method. Further condensation reaction was used to fabricate the double‐layer lauric acid modified Fe₃O₄ (DLF) nanoparticles dispersed well in water. Thermal properties of poly(N‐isopropylacrylamide) (PNIPAAm) and DLF/PNIPAAm composites and their aqueous solutions were measured by TGA and DSC. With the increasing of DLF content, the interaction between DLF and PNIPAAm caused the lower critical solution temperature (LCST) of polymer solution to shift from 33 to 31.25 °C. The effects of concentration and pH on LCST were also studied. The DLF/PNIPAAm nanofibers were fabricated by electrospinning. Their diameters were around 100–250 nm. Magnetization curves of DLF/PNIPAAm composite and nanofibers were overlapped and the saturated magnetizations were the same. Magnetic attraction behaviors of DLF/PNIPAAm polymer solution at temperatures below and above LCST were different. Aggregation of DLF/PNIPAAm above LCST enhanced magnetic moment density as well as magnetic attraction ability. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 848–856     

Atypical transition temperature dependence of poly(N‐isopropylacrylamide) and poly(N‐isopropylacrylamide‐co‐acrylamide) nanocomposites on the content of exfoliated montmorillonites

Exfoliated montmorillonite (MMT)/poly(N‐isopropylacrylamide) (PNIPAAm) and MMT/poly(N‐isopropylacrylamide‐co‐acrylamide) [P(NIPAAm‐co‐AAm)] nanocomposites were fabricated by soap‐free emulsion polymerization. Interestingly, as the content of MMT was increased from 0 to 10 wt %, the glass transition temperature of MMT/PNIPAAm was decreased from 145 to 122 °C, whereas that of the MMT/P(NIPAAm‐co‐AAm) increased from 95 to 153 °C. Although the lower critical solution temperature (LCST) of 32 °C for the MMT/PNIPAAm nanocomposites in aqueous solutions was slightly increased with the content of MMT, that of the MMT/P(NIPAAm‐co‐AAm) was decreased from 70 to 65 °C. A mechanism that the hydrogen bonds between the amide groups of PNIPAAm were interfered by the exfoliated MMT nano‐platelets for the MMT/PNIPAAm nanocomposites and the preferred absorption of acrylamide units to the MMT nanoplatelets rather than N‐isopropylacrylamide in the MMT/P(NIPAAm‐co‐AAm) nanocomposites was suggested to interpret these unusual transition behavior. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 524–530, 2009     

Temperature responsive carbon nanotubes/poly(N-isopropylacrylamide)-modified electrodes for electrochemical selective determination of dopamine, uric acid, and ascorbic acid

Poly(N-isopropylacrylamide)(PNIPAAm) with a lower critical solution temperature of about 32?°C was used as matrix to prepare temperature responsive carbon nanotubes (CNT) and functionalized CNT (fCNT) composites to modify glassy carbon electrode (GCE) as working electrode for electrochemical selective detection of dopamine, uric acid, and ascorbic acid. The GCE modification temperature (25 and 37?°C, denoted as 25f and 37f), working temperature (25 and 37?°C, denoted as 25aq and 37aq), and the type of CNT (CNT and fCNT) were found to significantly affect the electrocatalytic activity of the composites toward redox reactions of Fe(CN) ₆ ^3?/4? as a probe and the selective detection ability for the three analytes. The fCNT/PNIPAAm composite with the 25f–37aq temperature combination exhibited strong electrocatalytic activity and highly selective detection ability for the three analytes. In contrast, the same composite with the other three combinations (25f–25aq, 37f–25aq, and 37f–37aq) and the CNT/PNIPAAm composite with all four combinations exhibited insignificant electrocatalytic activity and no selective detection ability.     

Insulin release behavior of poly(N-isopropylacrylamide-co-N-vinyl-2-pyrrolidone) hydrogel based on modified melamine crosslinkers

Novel hydrogels based on poly(N-isopropylacrylamide-co-N-vinyl-2-pyrrolidone) (PNIPAAm/PNVP), were synthesized by solution radical polymerization using water as solvent and different weight percentage of crosslinkers ranging from 0.5 to 4%. The monomer mol ratios of NIPAAm/VP (0.9/0.1, 0.5/0.5, and 0.1/0.9) were used in all cases. N,N′-methylenebisacrylamide (MBA) and the new synthesized N,N,N-triacrylamido melamine (MAAm) were used as crosslinkers. The swelling parameters such as the swelling ratio Q, equilibrium water content (EWC), volume fraction of polymer φ_p and volume fraction at crosslinking φ_r were calculated from swelling measurements at different temperatures. The lower critical solution temperatures (LCST) of the prepared hydrogels were measured using DSC technique. The data of LCST indicated that the NIPAAm/VP crosslinked with MAAm or MBA showed reversible swelling and shrinking with temperature changes. The temperature dependence of swelling ratio and response kinetics upon heating or cooling was also investigated to understand the smart properties, i.e., temperature sensitive properties of these smart hydrogels. The in vitro release experiments were carried out at 22 and 37°C, respectively, to investigate the effect of temperature-sensitive property of these PNIPAAm/PNVP hydrogels crosslinked with MAAm and MBA crosslinkers on insulin release profiles.