Durability investigation of graphene-supported Pt nanocatalysts for PEM fuel cells

We report graphene nanosheets as a durable alternative support material for Pt nanoparticle catalysts for oxygen reduction in proton exchange membrane (PEM) fuel cells and compared them to XC-72. The materials were characterized by X-ray diffraction and transmission electron microscopy. Electrochemical surface oxidation of XC-72 and graphene, and of Pt/XC-72 and Pt/graphene has been compared following treatments for up to 120 h. The electrochemical performance of the specimens was evaluated by cyclic voltammetry and linear sweep voltammetry at different surface oxidation time intervals. Electrochemical measurements indicate that the graphene exihibits greatly enhanced electrochemical durability. It is suggested that graphene nanosheet is a promising, low-cost, and durable electrocatalyst support for oxygen reduction in the PEM fuel cell.     

One-pot, solvothermal synthesis of TiO(2)-graphene composite nanosheets

In this article, we propose a facile one-pot solvothermal route for synthesizing TiO(2)-graphene composite nanosheets (TGCN). In the system, ethylene glycol not only as a reducing agent can convert graphene oxide to reduced graphene oxide nanosheets, but also is employed to control the hydrolysis and condensation rates of tetrabutoxytitanium. The obtained TGCN hybrid materials are characterized by atomic force microscopy, transmission electron microscopy, UV-vis spectroscopy, Raman spectroscopy, X-ray photo-electron spectroscopy, X-ray diffraction, and thermal gravimetric analysis. It is found that the quantity of H(2)O used in the reaction is the key to obtain high-quality product. The photocatalytic activities of the products are evaluated using the photocatalytic degradation of methylene blue (MB) as a probe reaction. The results showed that the obtained TGCN have an enhanced adsorption capacity and remarkable improvements in the photodegradation rate of MB under visible light compared to P25.     

Synthesis and electrochemical performance of sandwich-like polyaniline/graphene composite nanosheets

Sandwich-like polyaniline/graphene composite nanosheets have been synthesized by chemical oxidation polymerization of aniline monomer on the surfaces of reduced graphene oxide nanosheets in the absence of any surfactants. The influences of the mass ratios of aniline and reduced graphene oxide on the sizes and morphologies of polyaniline/graphene nanocomposites have been investigated. As the mass ratio of aniline and reduced graphene oxide is smaller than 12:1, polymerization reaction of aniline occurs on the surfaces of reduced graphene oxide by heterogeneous nucleation to form sandwich-like polyaniline/graphene composite nanosheets. However, besides sandwich-like polyaniline/graphene composite nanosheets, polyaniline nanofibers are formed by homogeneous nucleation. In comparison with reduced graphene oxide and polyaniline nanofibers, the obtained sandwich-like polyaniline/graphene composite nanosheets exhibit good electrochemical performances due to the synergistic effect between graphene and polyaniline.     

超顺磁性氧化石墨烯复合材料固定辣根过氧化物酶催化去除氯酚

采用超声辅助共沉淀法成功地将磁性Fe3O4纳米颗粒沉积在氧化石墨烯表面,利用透射电镜、磁滞回归曲线和X射线光电子能谱对材料进行了表征。将该材料作为载体固定辣根过氧化物酶,考察了固定化酶催化2-氯酚、4-氯酚和2,4-二氯酚降解反应,研究了溶液pH值、反应温度、反应时间、H2O2和氯酚浓度以及固定化酶用量对酚类物质去除率的影响。基于取代基数量和位置不同,去除率排序为2-氯酚<4-氯酚<2,4-二氯酚。另外,采用GC-MS研究了降解过程中的氧化产物。固定化酶的生化性质研究表明,固定化酶比游离酶具有更好的储存稳定性、pH稳定性和热稳定性。经过4次循环利用,固定化酶仍保留66%的活性,说明磁性纳米材料可以分离回收并重复利用,在污水处理领域具有应用前景。     

Prosthetic heme modification during halide ion oxidation. Demonstration of chloride oxidation by horseradish peroxidase

Myeloperoxidase (MPO), eosinophil peroxidase (EPO), and chloroperoxidase can oxidize iodide, bromide, and chloride, but most peroxidases, including the prototypical horseradish peroxidase (HRP), reportedly only oxidize iodide and, in some cases, bromide. We report here that incubation of HRP with Br(-) and H(2)O(2) at acidic pH results in both bromination of monochlorodimedone and modification of the heme group. Mass spectrometry indicates that the heme 2- and 4-vinyl groups are modified by either replacement of a vinyl hydrogen by a bromide or addition of HOBr to give a bromohydrin. These reactions do not occur if protein-free heme and Br(-) are co-incubated with H(2)O(2) or if the HRP reaction is carried out at pH 7. Surprisingly, similar prosthetic heme modifications occur in incubations of HRP with H(2)O(2) and Cl(-). A mechanism is proposed involving oxidation of Br(-) or Cl(-) to give HOBr or HOCl, respectively, followed by addition to a vinyl group. In the reaction with Cl(-), a meso-chloro heme adduct is also formed. This first demonstration of Cl(-) oxidation by HRP, and the finding that prosthetic heme modification occurs when Br(-) or Cl(-) is oxidized in the absence of a cosubstrate, show that only modest tuning is required to achieve the unique chloride oxidation activity of MPO and EPO. The results raise the question of how the prosthetic hemes of MPO and EPO, whose function is to produce oxidized halide species, escape modification.     

Green synthesis of graphene nanosheets/ZnO composites and electrochemical properties

A green and facile approach was demonstrated to prepare graphene nanosheets/ZnO (GNS/ZnO) composites for supercapacitor materials. Glucose, as a reducing agent, and exfoliated graphite oxide (GO), as precursor, were used to synthesize GNS, then ZnO directly grew onto conducting graphene nanosheets as electrode materials. The small ZnO particles successfully anchored onto graphene sheets as spacers to keep the neighboring sheets separate. The electrochemical performances of these electrodes were analyzed by cyclic voltammetry, electrochemical impedance spectrometry and chronopotentiometry. Results showed that the GNS/ZnO composites displayed superior capacitive performance with large capacitance (62.2 F/g), excellent cyclic performance, and maximum power density (8.1 kW/kg) as compared with pure graphene electrodes. Our investigation highlight the importance of anchoring of small ZnO particles on graphene sheets for maximum utilization of electrochemically active ZnO and graphene for energy storage application in supercapacitors.     

石墨烯载Pt纳米粒子的原位还原制备及氧还原电催化性能

采用改进的化学氧化还原法(Hummers法)氧化鳞片石墨, 再超声振荡剥离得到氧化石墨烯(GO)水溶液. 通过聚二烯丙基二甲基氯化铵(PDDA)分子对GO表面功能化, 由于带正电荷的PDDA分子功能化的GO与带负电荷的^2-离子间的静电作用, 使Pt离子组装到GO表面, 再通过原位还原被束缚的Pt离子, 同时GO被还原成石墨烯片(GNs), 得Pt/PDDA-GNs催化剂. 相对空白GNs负载的Pt纳米粒子和商业化Pt/C(JM), Pt/PDDA-GNs催化剂有较高的氧还原活性和稳定性. 前者可归因于Pt颗粒尺寸细小和分散度较高, 后者是由于PDDA分子与Pt原子间的电子作用及对Pt颗粒的钉扎作用, 从而减缓了Pt的氧化和迁移.     

Self-assembled graphene/azo polyelectrolyte multilayer film and its application in electrochemical energy storage device

Graphene/azo polyelectrolyte multilayer films were fabricated through electrostatic layer-by-layer (LbL) self-assembly, and their performance as electrochemical capacitor electrode was investigated. Cationic azo polyelectrolyte (QP4VP-co-PCN) was synthesized through radical polymerization, postpolymerization azo coupling reaction, and quaternization. Negatively charged graphene nanosheets were prepared by a chemically modified method. The LbL films were obtained by alternately dipping a piece of the pretreated substrates in the QP4VP-co-PCN and nanosheet solutions. The processes were repeated until the films with required numbers of bilayers were obtained. The self-assembly and multilayer surface morphology were characterized by UV-vis spectroscopy, AFM, SEM, and TEM. The performance of the LbL films as electrochemical capacitor electrode was estimated using cyclic voltammetry. Results show that the graphene nanosheets are densely packed in the multilayers and form random graphene network. The azo polyelectrolyte cohesively interacts with the nanosheets in the multilayer structure, which prevents agglomeration of graphene nanosheets. The sheet resistance of the LbL films decreases with the increase of the layer numbers and reaches the stationary value of 1.0 × 10(6) Ω/square for the film with 15 bilayers. At a scanning rate of 50 mV/s, the LbL film with 9 bilayers shows a gravimetric specific capacitance of 49 F/g in 1.0 M Na(2)SO(4) solution. The LbL films developed in this work could be a promising type of the electrode materials for electric energy storage devices.     

凝胶渗透色谱法研究壳聚糖生物材料酶降解过程的均匀性

壳聚糖是一种重要的生物医用材料,脱乙酰度是影响其生物降解性能的重要因素。运用凝胶渗透色谱研究了脱乙酰 度及相对分子质量分布相似、而聚合单元N-乙酰氨基-D-葡萄糖和D-氨基葡萄糖分布不同的两种壳聚糖材料在溶菌酶作用 下的降解过程,分析检测了壳聚糖材料在降解过程中的重均相对分子质量、相对分子质量多分散性和相对分子质量分布 的变化。发现聚合单元为随机分布的壳聚糖样品,其降解是均匀的;而聚合单元为段状分布的壳聚糖样品,其降解是非 均匀的;表明其聚合单元的分布方式决定壳聚糖材料酶降解过程的均匀性。     

铁、氮掺杂石墨烯/碳黑复合材料的制备及氧还原电催化性能

以高含氮量的2-氨基咪唑为氮源,三氯化铁为铁源,高比表面积的KJ600碳黑为载体,通过水热法制得氨基咪唑聚合物前驱体,再经二次高温热处理,制得石墨烯/碳黑复合材料. 透射电镜表征显示该材料为石墨烯纳米片与碳黑颗粒的复合结构. BET表征表明这是一种多孔结构,具有很高的比表面积（882 m²•g^-1）,这有利于暴露更多活性位点,并促进传质. XRD证实催化剂中存在石墨烯,且石墨烯结构是在第一次热处理过程中形成的. 电化学测试表明,该催化剂在酸性和碱性介质中都具有很高的氧还原电催化活性和低H₂O₂产率,并且在碱性介质中对甲醇小分子的抗毒化性能明显优于商业Pt/C催化剂,展示出在实际燃料电池系统中的应用潜力.     

Controllable synthesis, magnetism and solubility enhancement of graphene nanosheets/magnetite hybrid material by covalent bonding

Hybrids of Fe(3)O(4) nanoparticles and surface-modified graphene nanosheets (GNs) were synthesized by a two-step process. First, graphene nanosheets were modified by SOCl(2) and 4-aminophenoxyphthalonitrile to introduce nitrile groups on their surface. Second, the nitrile groups of surface-modified graphene nanosheets were reacted with ferric ions on the surface of Fe(3)O(4) with the help of relatively high boiling point solvent ethylene glycol to form a GNs/Fe(3)O(4) hybrid. The covalent attachment of Fe(3)O(4) nanoparticles on the graphene nanosheet surface was confirmed by Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), energy-dispersive X-ray spectrometer (EDS) and scanning electron microscopy (SEM). TEM and HRTEM observations indicated that the sizes of the nanoparticles and their coverage density on GNs could be easily controlled by changing the concentration of the precursor and the weight ratio to GNs. Magnetic measurements showed that magnetization of the hybrid materials is strongly influenced by the reaction conditions. Chemically bonded by phthalocyanine, the solubility of as-synthesized GNs/Fe(3)O(4) hybrid materials was greatly enhanced, which was believed to have potential for applications in the fields of composites, wastewater treatment and biomaterials.     

石墨烯负载高活性Pd催化剂对乙醇的电催化氧化

以石墨粉为原料, 采用Hummers法液相氧化合成了氧化石墨(GO), 然后用化学一步还原制得石墨烯负载钯催化剂. X射线衍射(XRD)、透射电镜(TEM)表征表明, Pd在石墨烯载体上有较好的分散度, 粒径为3-5 nm. 电化学活性面积(EASA)、循环伏安(CV)、计时电流(CA)和计时电位(CP)等电化学测试表明, 与传统Pd/Vulcan XC-72相比, Pd/石墨烯催化剂对碱性介质中乙醇电催化氧化的催化活性有了很大的提高.     

石墨烯负载高活性Pd催化剂对乙醇的电催化氧化

以石墨粉为原料, 采用Hummers法液相氧化合成了氧化石墨(GO), 然后用化学一步还原制得石墨烯负载钯催化剂. X射线衍射(XRD)、透射电镜(TEM)表征表明, Pd在石墨烯载体上有较好的分散度, 粒径为3-5 nm. 电化学活性面积(EASA)、循环伏安(CV)、计时电流(CA)和计时电位(CP)等电化学测试表明, 与传统Pd/Vulcan XC-72相比, Pd/石墨烯催化剂对碱性介质中乙醇电催化氧化的催化活性有了很大的提高.     

石墨烯负载高活性Pd催化剂对乙醇的电催化氧化

以石墨粉为原料, 采用Hummers法液相氧化合成了氧化石墨(GO), 然后用化学一步还原制得石墨烯负载钯催化剂. X射线衍射(XRD)、透射电镜(TEM)表征表明, Pd在石墨烯载体上有较好的分散度, 粒径为3-5 nm. 电化学活性面积(EASA)、循环伏安(CV)、计时电流(CA)和计时电位(CP)等电化学测试表明, 与传统Pd/Vulcan XC-72相比, Pd/石墨烯催化剂对碱性介质中乙醇电催化氧化的催化活性有了很大的提高.     

石墨烯负载高活性Pd催化剂对乙醇的电催化氧化

以石墨粉为原料, 采用Hummers法液相氧化合成了氧化石墨(GO), 然后用化学一步还原制得石墨烯负载钯催化剂. X射线衍射(XRD)、透射电镜(TEM)表征表明, Pd在石墨烯载体上有较好的分散度, 粒径为3-5 nm. 电化学活性面积(EASA)、循环伏安(CV)、计时电流(CA)和计时电位(CP)等电化学测试表明, 与传统Pd/Vulcan XC-72相比, Pd/石墨烯催化剂对碱性介质中乙醇电催化氧化的催化活性有了很大的提高.     

石墨烯负载高活性Pd催化剂对乙醇的电催化氧化

以石墨粉为原料, 采用Hummers法液相氧化合成了氧化石墨(GO), 然后用化学一步还原制得石墨烯负载钯催化剂. X射线衍射(XRD)、透射电镜(TEM)表征表明, Pd在石墨烯载体上有较好的分散度, 粒径为3-5 nm. 电化学活性面积(EASA)、循环伏安(CV)、计时电流(CA)和计时电位(CP)等电化学测试表明, 与传统Pd/Vulcan XC-72相比, Pd/石墨烯催化剂对碱性介质中乙醇电催化氧化的催化活性有了很大的提高.     

石墨烯负载高活性Pd催化剂对乙醇的电催化氧化

以石墨粉为原料, 采用Hummers法液相氧化合成了氧化石墨(GO), 然后用化学一步还原制得石墨烯负载钯催化剂. X射线衍射(XRD)、透射电镜(TEM)表征表明, Pd在石墨烯载体上有较好的分散度, 粒径为3-5 nm. 电化学活性面积(EASA)、循环伏安(CV)、计时电流(CA)和计时电位(CP)等电化学测试表明, 与传统Pd/Vulcan XC-72相比, Pd/石墨烯催化剂对碱性介质中乙醇电催化氧化的催化活性有了很大的提高.     

石墨烯负载高活性Pd催化剂对乙醇的电催化氧化

以石墨粉为原料, 采用Hummers法液相氧化合成了氧化石墨(GO), 然后用化学一步还原制得石墨烯负载钯催化剂. X射线衍射(XRD)、透射电镜(TEM)表征表明, Pd在石墨烯载体上有较好的分散度, 粒径为3-5 nm. 电化学活性面积(EASA)、循环伏安(CV)、计时电流(CA)和计时电位(CP)等电化学测试表明, 与传统Pd/Vulcan XC-72相比, Pd/石墨烯催化剂对碱性介质中乙醇电催化氧化的催化活性有了很大的提高.     

石墨烯负载高活性Pd催化剂对乙醇的电催化氧化

以石墨粉为原料, 采用Hummers法液相氧化合成了氧化石墨(GO), 然后用化学一步还原制得石墨烯负载钯催化剂. X射线衍射(XRD)、透射电镜(TEM)表征表明, Pd在石墨烯载体上有较好的分散度, 粒径为3-5 nm. 电化学活性面积(EASA)、循环伏安(CV)、计时电流(CA)和计时电位(CP)等电化学测试表明, 与传统Pd/Vulcan XC-72相比, Pd/石墨烯催化剂对碱性介质中乙醇电催化氧化的催化活性有了很大的提高.     

石墨烯负载高活性Pd催化剂对乙醇的电催化氧化

以石墨粉为原料, 采用Hummers法液相氧化合成了氧化石墨(GO), 然后用化学一步还原制得石墨烯负载钯催化剂. X射线衍射(XRD)、透射电镜(TEM)表征表明, Pd在石墨烯载体上有较好的分散度, 粒径为3-5 nm. 电化学活性面积(EASA)、循环伏安(CV)、计时电流(CA)和计时电位(CP)等电化学测试表明, 与传统Pd/Vulcan XC-72相比, Pd/石墨烯催化剂对碱性介质中乙醇电催化氧化的催化活性有了很大的提高.