LLDPE/纳米SiO2膜的光学性能

LLDPE;农膜;LLDPE/纳米SiO2膜的光学性能     

聚丙烯酸丁酯接枝的纳米SiO2对聚甲醛的改性

采用原子转移自由基聚合法(ATRP)在纳米SiO2粒子表面接枝聚丙烯酸丁酯(PBA)制备了纳米复合粒子SiO2-g-PBA,并以此对聚甲醛(POM)进行改性. 通过红外光谱、热失重分析、透射电子显微镜及扫描电子显微镜等分析技术进行了表征. 结果,SiO2-g-PBA在POM中分散均匀,使POM/SiO2-g-PBA复合材料的缺口冲击强度明显高于POM及POM/ SiO2复合材料. 当SiO2-g-PBA纳米复合粒子的质量分数为2%时,POM/SiO2-g-PBA复合材料的冲击强度达71.2 kJ/m2,较纯POM提高了7倍多,同时拉伸强度也有一定的提高,达到68.1 MPa.     

纳米SiO_2粒子表面官能团对尼龙6原位聚合的影响

研究了无机纳米粒子表面反应性官能团对尼龙 6 纳米SiO2 原位聚合的影响 .红外光谱和热重分析结果证实了无论对SiO2 进行表面处理与否 ,在原位聚合过程中其表面均能形成一定量的接枝聚合物 .随表面反应性官能团数目的增加 ,SiO2 的表面接枝率呈上升趋势 .与纯的尼龙 6相比 ,带有不同反应性官能团的纳米SiO2 的加入使复合产物的分子量呈下降的趋势 .对应于复合体系中可能发生的反应 ,提出了几种可能的表面接枝的键接方式 .力学性能测试结果显示经表面处理的SiO2 的加入能同时提高复合物的强度和韧性 ,而加入未处理的SiO2 时 ,材料强度可得到提高 ,但韧性明显降低 ,表明由偶联剂处理引入的柔性界面层的存在对于复合材料的力学性能有重要的影响     

尼龙6/SiO_2纳米复合材料的制备及其力学性能和热稳定性

以表面含有氨基的可反应性纳米SiO2(RNS-A)和表面含有烷基碳链的可分散性纳米SiO2(DNS-3)作为填料,利用原位聚合法制备了尼龙6/SiO2纳米复合材料(相应的复合材料分别简记为RPA和DP3);采用透射电子显微镜观察了复合材料中纳米SiO2的表面形貌,并利用热失重分析仪测定了复合材料的热稳定性,进而考察了纳米SiO2表面功能基团对尼龙6力学性能和热稳定性的影响.结果显示,纳米SiO2能够很好地分散在尼龙6基体中,并使尼龙6的热分解温度提高10℃左右.与此同时,RPA的最大拉伸强度和冲击强度较纯尼龙6的分别提高34.5%和12.5%,DP3的最大拉伸强度和冲击强度分别提高18.2%和45.7%.这表明两种纳米SiO2均可以有效地提高尼龙6的力学性能和热稳定性;可以推测,纳米SiO2的增强效应与其在尼龙6基体材料中的分散和界面作用有关.     

纳米SiO_2/聚甲基丙烯酸甲酯复合材料的制备和力学性能

通过悬浮聚合的方法,用不同表面结构的纳米SiO2对聚甲基丙烯酸甲酯(PMMA)进行原位改性,得到纳米SiO2/聚甲基丙烯酸甲酯复合材料;利用红外光谱仪分析了复合材料的界面化学结构,利用热分析仪测定了其热稳定性,并采用冲击试验机测定了其力学性能.结果表明,不同表面结构的纳米SiO2均参与甲基丙烯酸甲酯的聚合反应,与PMMA基体之间形成化学键;而表面修饰有双键的纳米SiO2更易与甲基丙烯酸甲酯聚合,能更有效地提高PMMA的抗冲击性能.     

超支化聚乙烯亚胺接枝二氧化硅的制备及在聚丙烯改性中的应用

首先利用3-缩水甘油氧基丙基三甲氧基硅烷(简称GPS)作为偶联剂,对纳米SiO2进行表面改性,获得表面含有环氧基的SiO2纳米粒子(SiO2-GPS).利用这些环氧基与超支化聚乙烯亚胺(HPEI)分子中的氨基进行反应,得到SiO2接枝超支化聚乙烯亚胺的纳米粒子(SiO2-GPS-g-HPEI).然后利用SiO2-GPS-g-HPEI与聚丙烯(PP)和PP接枝的马来酸酐(PP-g-MAH)共混、模压,制备PP/SiO2-GPS-g-HPEI/PP-g-MAH复合材料.红外光谱测试和热失重分析(TGA)测试结果表明,SiO2纳米粒子表面依次接枝了GPS和HPEI;扫描电子显微镜(SEM)的测试结果显示,SiO2-GPS-g-HPEI在聚丙烯基体中分散良好,其材料的冲击断裂为韧性断裂;复合材料共混时,扭矩的增加证明了共混物中分散相(SiO2-GPS-g-HPEI)与基体(PP/PP-g-MAH)界面之间存在一定的相互作用.少量SiO2-GPS-g-HPEI加入PP/PP-g-MAH中,冲击强度可增加96.3%,拉伸强度也有较大的提高.     

SiO_2/C复合负极材料的制备及其性能

采用在纳米SiO2表面包覆聚苯胺,并经过热处理后,制备了SiO2/C纳米复合材料.通过X射线衍射(XRD)、热重分析(TGA)、扫描电子显微镜(SEM)和透射电子显微镜(TEM)对材料的晶体结构和表观形貌进行了表征.同时也对材料的电化学性能进行了测试,结果表明,50 mA/g电流密度下,SiO2/C纳米复合材料首次放电比容量达到830.5 mAh/g,100次循环后,放电比容量仍然保持在510 mA/g以上.电化学交流阻抗测试表明,SiO2表面包覆的碳层能显著减小电极的界面阻抗,提高电池的电化学性能.     

聚丁二酸丁二酯/纳米二氧化硅共混体系的结晶和动态力学性能研究

用溶液共混法制备了聚丁二酸丁二酯(PBS)/纳米二氧化硅(nano-SiO2)复合材料,并通过DSC、XRD、TEM和DMTA对其结晶、微观结构和动态力学性能进行了研究.DSC与XRD结果表明,在PBS中加入纳米SiO2,提高了PBS的结晶温度,并随着nano-SiO2含量的增加呈正相相关性,从纯PBS的67.7℃提高到含5%nano-SiO2时的73.3℃;在空气淬火条件下,提高了复合材料中PBS的结晶度,在nano-SiO2含量为2%时达到42.4%;TEM照片表明SiO2与基体PBS的界面模糊,表明二者之间具有一定的相互作用;这种相互作用和复合材料结晶性能的变化使PBS/nano-SiO2复合材料的储能模量和损耗因子均高于纯PBS.上述结果表明在PBS中添加适量的nano-SiO2,能显著提高PBS的结晶和动态力学性能.     

尿素水解法制备球形磁性Al2O3复合材料

利用酸化法在磁性Fe3O4纳米粒子表面包覆SiO2膜,制备了Fe3O4/SiO2复合粒子。然后将该复合粒子超声分散在尿素和铝盐的混合溶液中,利用油中成型法制备出球形纳米磁性Al2O3复合材料,通过水热焙烧等工序处理得γ-Al2O3。实验中采用XRD、TEM、BET、AGM等方法对复合粒子的性能进行了表征,探讨了制备过程对产物晶型的影响、产物的孔结构变化和磁学性能。另外添加的SiO2膜阻止了磁性Fe3O4纳米粒子的进一步团聚,使得Fe3O4纳米粒子保持较小尺寸并均匀分散在产物中,复合材料表现出超顺磁性;同时SiO2膜防止了磁核部分与Al2O3包覆层在高温焙烧时发生反应;还起到加强粘结的作用,使得Al2O3在使用过程中不容易脱落。     

回收聚乙烯醇缩丁醛/二氧化硅复合材料的制备与性能研究

利用硅烷偶联剂KH560对气相法SiO2进行表面改性,对改性前后SiO2的堆积密度、表面结构与形貌进行了分析。而后采用熔融共混法将SiO2添加到回收PVB膜片中,比较SiO2改性前后复合材料的力学性能、微观形貌及动态流变行为。结果表明:改性后SiO2表面接枝上KH560,其堆积密度明显增加;改性SiO2与PVB之间存在明显的相互作用,可显著降低回收PVB膜片加工黏附性;SiO2改性前后复合材料拉伸性能与回收PVB膜片相比均稍有降低,而撕裂强度有所增加。     

PTFE/纳米SiO2复合材料的制备及其力学性能

聚合物／纳米级无机粒子复合材料是纳米材料中的一种具有重要价值的新型材料，可广泛应用于橡胶、塑料、纤维三大合成材料之中。采用纳米级无机粒子填充聚合物基复合材料，可以在材料的补强、增韧等改性中获得良好的效果。本文以纳米SiO2为填料，将其经过有机处理后，制备了FIFE／纳米SiO2复合材料，并研究了纳米SiO2的含量对PTFE复合材料性能的影响。     

静电纺丝制备SiO2短纤维对聚丙烯冲击性能的影响

采用静电纺丝技术, 结合正硅酸乙酯(TEOS)的溶胶-凝胶反应制备出了直径为500 nm的SiO2短纤维(n-SF). 纤维经过硅烷偶联剂KH570表面处理后, 与聚丙烯(PP)通过螺杆混合制得复合材料. 通过SEM观察, KH570处理过的SiO2短纤维(n-MSF)在PP基体中分散均匀, 界面结合良好. DSC和XRD测试结果表明, n-SF和n-MSF的加入均可提高PP的结晶速率, 同时改变PP中β晶含量, 进而影响冲击强度; 冲击实验结果表明, n-MSF添加量为3%(质量分数)时, 复合材料冲击性能比纯PP提高了40.3%.     

Preparation and characterization of glass fiber–reinforced polyethylene terephthalate/linear low density polyethylene (GF‐PET/LLDPE) composites

Polyethylene terephthalate (PET) was melt blended with linear low density polyethylene (LLDPE) and subsequently compounded with glass fibers (GF) as reinforcements at percentages ranging from 15 to 45 wt% of LLDPE and 5 to 30 wt% of GF. Thermal, morphological, and mechanical properties of the prepared composites were investigated. It was found that compounding PET/LLDPE blends with GF would be beneficial in producing composites that are thermally stable with good mechanical properties. For example, the impact strength of the composites containing 85/15 wt% (PET/LLDPE) at relatively high loading of GF, ie, from 15 to 30 wt%, was higher than that of the GF‐reinforced neat PET. When increasing the percentage of LLDPE in the composites, the impact strength increased with increasing GF content, and this was also better than that of GF‐reinforced PET whose impact strength drastically decreased upon increasing the GF%. The improvement in mechanical properties of the composite, we suggest, should be correlated with the morphologies of the composites where the visualized interface adhesion tended to be better at higher loadings of both LLDPE and GF.     

Silica dispersion and properties of silica filled ESBR/BR/NR ternary blend composites by applying wet masterbatch technology

Silica is used as a reinforcing filler in the rubber product such as a tire. When silica contents increased in the composite, deterioration of the processability and silica dispersion in silica-rubber composites cannot be overcome only by adding a silane coupling agent. Therefore, silica wet-masterbatch (WMB) technology is considered for manufacturing highly silica filled composites. Herein, we investigated silica dispersion, cure behavior, mechanical properties, abrasion characteristics, and viscoelastic properties of 3 types of WMB blend composites. Up to 82% improvement in silica dispersion was determined by the Payne effect and confirmed by atomic-force microscopy. The tensile strength and elongation at break increased and tan δ at 60 °C decreased by improving silica dispersion. The silica WMB is suitable for manufacturing highly silica filled composites.     

The effects of a silane coupling agent on curing characteristics and mechanical properties of bamboo fibre filled natural rubber composites

The effects of a silane coupling agent on curing characteristics and mechanical properties of bamboo fibre filled natural rubber composites were studied. Scorch time, t₂ and cure time, t₉₀ of the composites decrease with increasing filler loading and with the presence of a silane coupling agent, Si69. Mooney viscosity also increases with increasing filler loading but at a similar filler loading shows lower value with the presence of Si69. The mechanical properties of composites viz tensile strength, tear strength, hardness and tensile modulus were also improved with the addition of Si69.     

Modified silica-based isoprene rubber composite by a multi-functional silane: Preparation and its mechanical and dynamic mechanical properties

Modified silica-based isoprene rubber (IR) composite has been designed and prepared by using a multi-functional silane, 2-aminoethyl-2-(3-triethoxysilylpropyl)aminoethyl disulfide (ATD), as coupling agent. Such modification significantly improved the dispersity of silica in the corresponding composites, as verified by SEM observation. And the hardness, tensile strength, stress at definite elongation, tear strength and temperature rise as well as the value of dynamic loss coefficient ranging from 0 °C to 80 °C of silica/IR vulcanized composites, are significantly improved, especially with low ATD dosage (2–4 phr). This modification of silica-based IR composite by employing ATD as coupling agent provides a facile and effective method to prepare silica-based rubber composites with improved mechanical properties and low hysteresis.     

Thermal, mechanical and electrical properties of copper powder filled low-density and linear low-density polyethylene composites

Low-density polyethylene (LDPE) and linear low-density polyethylene (LLDPE) with different copper contents were prepared by melt mixing. The copper powder particle distributions were found to be relatively uniform at both low and high copper contents. There was cluster formation of copper particles at higher Cu contents, as well as the formation of percolation paths of copper in the PE matrices. The DSC results show that Cu content has little influence on the melting temperatures of LDPE and LLDPE in these composites. From melting enthalpy results it seems as if copper particles act as nucleating agents, giving rise to increased crystallinities of the polyethylene. The thermal stability of the LDPE filled with Cu powder is better than that for the unfilled polymer. The LLDPE composites show better stability only at lower Cu contents. Generally, the composites show poorer mechanical properties (except Young's modulus) compared to the unfilled polymers. The thermal and electrical conductivities of the composites were higher than that of the pure polyethylene matrix for both the LDPE and LLDPE. From these results the percolation concentration was determined as 18.7 vol.% copper for both polymers.     

Influence of surface modification of fillers and polymer on flammability and tensile behaviour of polypropylene-composites

An intumescent system consisting of ammonium polyphosphate (APP) as an acid source and blowing agent, pentaerythritol (PER) as a carbonific agent and natural zeolite (clinoptilolite, Gördes II) as a synergistic agent was used in this study to enhance flame retardancy of polypropylene (FR-PP). Zeolite was incorporated into flame retardant formulation at four different concentrations (1, 2, 5, and 10 wt%) to investigate synergism with the flame retardant materials. Filler content was fixed at 30 wt% of total amounts of flame retardant PP composites. Zeolite and APP were treated with two different coupling agents namely, 3-(trimethoxysilyl)-1-propanethiol and (3-aminopropyl)-triethoxysilane for investigation of the influence of surface treatments on mechanical properties and flame retardant performance of composites. Maleic anhydride grafted polypropylene (MAPP) was used for making polypropylene hydrophilic. Flammability of FR-PP composites was measured by the determination of limiting oxygen index (LOI). The LOI values reached to a maximum value of 41% for mercapto silane treated APP:PER (2:1) PP composite containing 5 wt% zeolite. The tensile strength of composites was increased by the addition of MAPP and elongation at break of composites was increased with silane treatments.     

Thermomechanical and shape memory properties of SCF/SBS/LLDPE composites

A thermally triggered shape memory polymer composite was prepared by blending short carbon fiber (SCF) into a blend of poly(styrene-b-butadiene-b-styrene) triblock copolymer (SBS)/linear low density polyethylene (LLDPE) prior to curing. These composites have excellent processability compared with other thermosets. The dynamic mechanical analysis (DMA) and differential scanning calorimetry (DSC) were investigated to assess the thermomechanical properties of the SCF/SBS/LLDPE composite. Scanning electron microscope (SEM) imaging of the samples was performed to show the distribution of the SCF in the composite. The study specifically focused on the effect of SCF on the shape memory behavior of the SCF/SBS/LLDPE composite. The results indicated that the large amount of SCF significantly improved the mechanical property of the polymer composites while not damaging the shape memory performance. The SCF/SBS/LLDPE composites exhibited excellent shape memory behavior when the SCF content was less than 15.0 wt%. Moreover, the shape fixity ratio and shape recovery time of the SCF/SBS/LLDPE composites increased with the SCF content.