Spectroscopic and electrochemical studies of U(IV)-hexachloro complexes in hydrophobic room-temperature ionic liquids [BuMeIm][Tf2N] and [MeBu3N][Tf2N

The behavior of U(IV) octahedral complexes [cation]2[UCl6], where the [cation]+ is [BuMeIm]+ and [MeBu3N]+, is studied using UV/visible spectroscopy, cyclic staircase voltammetry, and rotating disk electrode voltammetry in hydrophobic room-temperature ionic liquids (RTILs) [BuMeIm][Tf2N] and [MeBu3N][Tf2N], where BuMeIm+ and MeBu3N+ are 1-butyl-3-methylimidazolium and tri-n-butylmethylammonium cations, respectively, and Tf2N- is the bis(trifluoromethylsulfonyl)imide anion. The absorption spectra of [cation]2[UCl6] complexes in the RTIL solutions are similar to the diffuse solid-state reflectance spectra of the corresponding solid species, indicating that the octahedral complex UCl6(2-) is the predominant chemical form of U(IV) in Tf2N--based hydrophobic ionic liquids. Hexachloro complexes of U(IV) are stable to hydrolysis in the studied RTILs. Voltammograms of UCl(6)2- at the glassy carbon electrode in both RTILs and at the potential range of -2.5 to +1.0 V versus Ag/Ag(I) reveal the following electrochemical couples: UCl6-/UCl6(2-) (quasi-reversible system), UCl(6)2-/UCl6(3-) (quasi-reversible system), and UCl(6)2-/UCl6(Tf2N)x-3+x (irreversible reduction). The voltammetric half-wave potential, Ep/2, of the U(V)/U(IV) couple in [BuMeIm][Tf2N] is positively shifted by 80 mV compared with that in [MeBu3N][Tf2N]. The positive shift in the Ep/2 value for the quasi-reversible U(IV)/U(III) couple is much greater (250 mV) in [BuMeIm][Tf2N]. Presumably, the potential shift is due to the specific interaction of BuMeIm+ with the uranium-hexachloro complex in ionic liquid. Scanning the negative potential to -3.5 V in [MeBu3N][Tf2N] solutions of UCl6(2-) reveals the presence of an irreversible cathodic process at the peak potential equal to -3.12 V (at 100 mV/s and 60 degrees C), which could be attributed to the reduction of U(III) to U(0).     

Stability of [MeBu3N][Tf2N] under gamma irradiation

The stability of the ionic liquid [MeBu3N][Tf2N], dry or after contact with water (where [MeBu3N]+ is the methyltributylammonium cation and [Tf2N](-) is the bistriflimide anion), was studied under 137Cs gamma irradiation in argon and in air. In a quantitative study with an absorbed dose of 2 MGy this ionic liquid was highly stable regardless of the radiolysis conditions. The radiolytic disappearance yields determined by ESI-MS were -0.38 and -0.25 micromol J(-1) for the cation and anion, respectively. ESI-MS, NMR, and liquid chromatography coupled with ESI-MS identified a large number of degradation products in very small quantities for the same dose. The cation radicals were formed by the loss of a Bu group, the Me group, or two H atoms to form a double bond with the butyl chain. Radiolysis of the anion produced mainly F and CF3 radicals. The anion radicals recombined with the cation to form a wide range of secondary degradation products regardless of the radiolysis conditions.     

Solvation of UCl6(2-) anionic complex by MeBu3N(+), BuMe2Im(+), and BuMeIm(+) cations

The complexes [MeBu 3N] 2[UCl 6] and [BuMe 2Im] 2[UCl 6] were characterized in the solid state and in solution of [MeBu 3N][Tf 2N], [BuMe 2Im][Tf 2N], and [BuMeIm][Tf 2N] room-temperature ionic liquids using single-crystal XRD, EXAFS, electrochemistry, UV-visible absorption spectroscopy, and NMR. In the solid state and in solution, the existence of hydrogen bonding between the UCl 6 (2-) complex and the ionic liquid cations was revealed by these techniques. The MeBu 3N (+) cation interacts with UCl 6 (2-) via the protons on the alpha-carbon atoms of nitrogen. The protons of the imidazolium ring account for the interaction between the BuMe 2Im (+) cation and the UCl 6 (2-) anion. For the BuMeIm (+) cation the major interaction was confirmed between the most acidic proton on C(2) and the chlorides of UCl 6 (2-). The experimental results also show that the intensity of the interaction between the UCl 6 (2-) anion and the cation varies with the ionic liquid cation in the following order: MeBu 3N (+) approximately BuMe 2Im (+) < BuMeIm (+).     

Formation of higher chloride complexes of Np(IV) and Pu(IV) in water-stable room-temperature ionic liquid [BuMeIm][Tf2N

A UV/vis/near-IR spectroscopic study shows that in [BuMeIm][(CF3SO2)2N] hydrophobic room-temperature ionic liquid solutions, [BuMeIm]2[AnCl6] complexes, where BuMeIm+ is 1-n-butyl-3-methylimidazolium and An(IV) is Np(IV) or Pu(IV), have an octahedral An(IV) environment similar to that observed in solid complexes. Water has no influence on the absorption spectra of AnCl6(2-) complexes, indicating their stability to hydrolysis in ionic liquid. Adding [BuMeIm]Cl modifies the UV/vis/near-IR absorption spectra of An(IV) in the ionic liquid and causes solids to precipitate. The solid-state reflectance spectra of the precipitates reveal considerable differences from the corresponding An(IV) hexachloro complexes. A voltammetric study indicates that AnCl6(2-) complexes are electrochemically inert in [BuMeIm][(CF3SO2)2N] at the glassy carbon working electrode. By contrast, quasi-reversible electrochemical reduction An(IV)/An(III) and An(IV) oxidation are observed in ionic liquids in the presence of [BuMeIm]Cl. The oxidation wave of noncoordinated chloride ions interferes with the An(IV) oxidation waves. The spectroscopic and voltammetric data clearly indicate the formation of nonoctahedral actinide(IV) chloride complexes with a Cl-/An(IV) ratio exceeding 6/1 in [BuMeIm][(CF3SO2)2N] in excess chloride ions.     

Autocatalytic sonolysis of iron pentacarbonyl in room temperature ionic liquid [BuMeIm][Tf2N

The autocatalytic sonochemical reaction of Fe(CO)(5) decomposition in [BuMeIm][Tf(2)N] provides iron nanoparticles in higher yields than in tetralin. Such a difference is explained by the higher decomposition of the intermediate Fe(3)(CO)(12) according to the two-sites model of the sonochemical reactions and the specific properties of the ionic liquid.     

Europium(III) and its halides in anhydrous room-temperature imidazolium-based ionic liquids: a combined TRES, EXAFS, and molecular dynamics study

Combining spectroscopic techniques (TRES and EXAFS) and molecular dynamics simulations, we have investigated the state of trivalent europium dissolved in room-temperature ionic liquids (RTILs), as a function of the RTIL anion and in the presence of added chloride anions. The studied RTILs are based on the 1-butyl-3-methyl-imidazolium (Bumim+) cation and differ by their anionic counterparts: BF4-, PF6-, Tf- (triflate, CF3SO3-), and Tf2N- [(CF3SO2)2N-]. The results show the strong influence of the RTIL nature on the first solvation shell of europium and on its complexation with chloride. Depending on the RTIL, europium(III), which was introduced in solution as a triflate salt, is found to be solvated either by RTIL anions only or as neutral undissociated EuTf3 moieties completed by solvent anions. Kinetic effects, related to the viscosity of the RTIL and the nature of the europium salt, also markedly influence the coordination of added Cl- or F- anions to the metal.     

Alkali cation extraction by calix[4]crown-6 to room-temperature ionic liquids. The effect of solvent anion and humidity investigated by molecular dynamics simulations

We report a molecular dynamics study on the solvation of M+ (Na+ to Cs+) alkali cations and of their LM+ complexes with a calix[4]arene host (L = 1,3-dimethoxy-calix[4]arene-crown-6 in the 1,3-alternate conformation) in the [BMI][PF6] and [BMI][Tf2N] room-temperature ionic liquids "ILs" based on the BMI+ (1-butyl-3-methylimidazolium) cation. The comparison of the two liquids and the dry versus humid form of the former one (with a 1:1 ratio of H2O and BMI+PF6- species) reveals the importance of humidity: in [BMI][PF6]-dry as in the [BMI][Tf2N] liquid, the first solvation shell of the "naked" M+ ions is composed of solvent anions only (four PF6- anions, and from four to five Tf2N- anions, respectively, quasi-neutralized by a surrounding cage of BMI+ cations), while in the [BMI][PF6]-humid IL, it comprises from one to three solvent anions and about four H2O molecules. In the LM+ complexes, the cation is shielded from solvent, but still somewhat interacts with a solvent anion in the dry ILs and with water in the humid IL. We also report tests on M+ interactions with solvent anions PF6- and Tf2N- in the gas phase, showing that the AMBER results are in satisfactory agreement with QM results obtained at different levels of theory. The question of ion recognition by L is then examined by free energy perturbation studies in the three liquids, predicting a high Cs+/Na+ selectivity upon liquid extraction from an aqueous phase, in agreement with experimental results on a parent calixarene host. A similar Cs+/Na+ selectivity is predicted upon complexation in a homogeneous IL phase, mainly due to the desolvation energy of the free cations. Thus, despite their polar character, ionic liquids qualitatively behave as classical weakly polar organic liquids (e.g., choroform) as far as liquid-liquid extraction is concerned but more like polar liquids (water, alcohols) as far as complexation in a single phase is concerned.     

γ辐射下CMPO/[C2mim][NTf2]的辐解及其对Eu3+萃取的影响

主要考察了辛基(苯基)-N, N-二异丁基胺甲酰基甲基氧化膦(CMPO)在1-乙基-3-甲基咪唑双三氟甲基磺酰胺酸盐([C₂mim][NTf₂])中的γ辐解行为,同时考察辐射对CMPO/[C₂mim][NTf₂]萃取能力的影响。通过超高效液相色谱-四极杆飞行时间质谱联用仪(UPLC/Q-TOF-MS)进行定量分析、辐解产物认定以及产物半定量分析。CMPO/正十二烷作为对比条件进行了相同研究。结果表明：CMPO在[C₂mim][NTf₂]中的辐解率低于其在正十二烷中,并且辐解路径不同。在正十二烷体系中,CMPO主要发生C―P、C―N键的断链,而在离子液体体系中CMPO主要发生异丁基脱除反应,并与[C₂mim]^+·、·CF₃等离子液体产生的自由基发生取代反应。综合辐解研究结果,我们提出CMPO/[C₂mim][NTf₂]的辐解路径,这加深了CMPO在离子液体中辐解机理的认识。最后,通过萃取实验发现,当硝酸浓度为0.01 mol·L^-1,辐照剂量为800 kGy时,CMPO/[C₂mim][NTf₂]对Eu³⁺的萃取率依旧达到99%以上。     

Silylene extrusion from organosilanes via double geminal Si-H bond activation by a Cp*Ru(kappa2-P,N)+ complex: observation of a key stoichiometric step in the glaser-tilley alkene hydrosilylation mechanism

Treatment of Cp*RuCl(kappa2-P,N-2b) (2b = 2-NMe2-3-PiPr2-indene) with TlSO3CF3 produced the cyclometalated complex [4]+SO3CF3- in 94% isolated yield. Exposure of [4]+X- (X = B(C6F5)4 or SO3CF3) to Ph2SiH2 (10 equiv) or PhSiH3 afforded the corresponding [Cp*(mu-P,N-2b)(H)2Ru=SiRPh]+X- complexes, [5]+X- (R = Ph; X = B(C6F5)4, 82%; X = SO3CF3, 39%) and [6]+X- (R = H; X = B(C6F5)4, 94%; X = SO3CF3, 95%). Notably, these transformations represent the first documented examples of Ru-mediated silylene extrusion via double geminal Si-H bond activation of an organosilane-a key step in the recently proposed Glaser-Tilley (G-T) alkene hydrosilylation mechanism. Treatment of [5]+B(C6F5)4- with KN(SiMe3)2 or [6]+SO3CF3- with NaN(SiMe3)2 afforded the corresponding zwitterionic Cp*(mu-2-NMe2-3-PiPr2-indenide)(H)2Ru=SiRPh complex in 69% (R = Ph, 7) or 86% (R = H, 8) isolated yield. Both [6]+X- and 8 proved unreactive toward 1-hexene and styrene and provided negligible catalytic turnover in the attempted metal-mediated hydrosilylation of these substrates with PhSiH3, thereby providing further empirical evidence for the required intermediacy of base-free Ru=Si species in the G-T mechanism. Isomerization of the P,N-indene ligand backbone in [6]+X-, giving rise to [Cp*(mu-1-PiPr2-2-NMe2-indene)(H)2Ru=SiHPh]+X- ([9]+X-), was observed. In the case of [9]+SO3CF3-, net intramolecular addition of the Ru=Si-H group across the styrene-like C=C unit within the ligand backbone to give 10 (96% isolated yield) was observed. Crystallographic characterization data are provided for [4]+X-, [5]+X-, [6]+X-, 8, and 10.     

Cation-anion interactions in 1-ethyl-3-methylimidazolium trifluoromethanesulfonate-based ionic liquid electrolytes

An important step in developing ionic-liquid-based electrolytes for lithium rechargeable batteries is obtaining a molecular-level understanding of the ionic interactions that occur in these systems. In this study, 1-ethyl-3-methylimidazolium trifluoromethansulfonate ([C2mim]CF3SO3) is complexed with LiCF3SO3, and the local structures of the CF3SO3- and [C2mim]+ ions are investigated with infrared and Raman spectroscopy. The isolation and subsequent refinement of a Li[C2mim](CF3SO3)2 crystal provides further insight into the structure of the [C2mim]CF3SO3-LiCF3SO3 solutions. Minor changes are observed in the infrared and Raman spectra of dilute [C2mim]CF3SO3-LiCF3SO3 solutions compared to pure [C2mim]CF3SO3. However, a suspension of very small Li[C2mim](CF3SO3)2 crystallites forms at a solution composition of [C2mim]CF3SO3:LiCF3SO3 = 10:1 (mole ratio), placing an upper limit on the solubility of LiCF3SO3. Essentially no changes are observed in the vibrational modes of the [C2mim]+ cations over the entire range of LiCF3SO3 compositions studied, suggesting that the addition of these compounds does not significantly perturb the local structure of the [C2mim]+ cations. The salt used in this study has a common anion with the ionic liquid; thus, the ion cloud surrounding the [C2mim]+ ions, which must be primarily composed of CF3SO3- anions, is not significantly altered with the addition of LiCF3SO3.     

N-(trifluoromethylsulfonyl)aryloxytrifluoromethylsulfoximines [ArO-SO(CF3)=NTf] and N-aryltriflimides Ar-N(Tf)2 by thermal and photolytic dediazoniation of [ArN2][BF4] in [BMIM][Tf2N] ionic liquid: exploiting the ambident nucleophilic character of a "nonnucleophilic" anion

Arenediazonium tetrafluoroborate salts undergo metathesis on immobilization in 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonato)amide [BMIM][Tf(2)N]. The "noncoordinating", "nonnucleophilic" [Tf(2)N] anion acts as an ambident nucleophile toward the aryl cations, formed via thermal dediazoniation, to give predominantly the oxy anion quenching products [ArO-SO(CF(3))=NTf], with minimal formation of ArN(Tf)(2), irrespective of the nature of the substituent(s) on the ArN(2)+. Strong preference for the formation of oxygen trapping products did not change under photolytic conditions, where dediazoniation occurs at room temperature. A minimal amount of the Schiemann product ArF is also formed in both thermal and photolytic dediazoniation, depending on the substituent(s). Progress of dediazoniation in the IL (both thermal and photolytic) and the evolution of the products were directly monitored by (1)H and (19)F NMR. According to DFT (Density Functional Theory) calculations, PhN(Tf)(2) is more stable than PhO-SO(CF(3))=NTf by 15-17 kcal/mol, depending on the basis set. Inclusion of solvation effects (PCM, with acetone and with CH(2)ClCH(2)Cl as solvent) did not change this preference. The [ArN(2)][BF(4)] dediazoniation in [BMIM][Tf(2)N] resulted in synthesis and characterization of a series of hitherto unknown [ArO-SO(CF(3))=NTf] compounds. The X-ray structure of MesO-SO(CF(3))=NTf (Mes = mesityl) is reported. On the basis of extraction studies, suitable solvent systems have been identified that remove the products without dissolving [BMIM][NTf(2)], thus overcoming product recovery difficulties typically associated with the use of this IL.     

The [BMI][Tf2N] ionic liquid/water binary system: a molecular dynamics study of phase separation and of the liquid-liquid interface

We report molecular dynamics (MD) simulations of the aqueous interface of the hydrophobic [BMI][Tf2N] ionic liquid (IL), composed of 1-butyl-3-methylimidazolium cations (BMI+) and bis(trifluoromethylsulfonyl)imide anions (Tf2N-). The questions of water/IL phase separation and properties of the neat interface are addressed, comparing different liquid models (TIP3P vs TIP5P water and +1.0/-1.0 vs +0.9/-0.9 charged IL ions), the Ewald vs the reaction field treatments of the long range electrostatics, and different starting conditions. With the different models, the "randomly" mixed liquids separate much more slowly (in 20 to 40 ns) than classical water-oil mixtures do (typically, in less than 1 ns), finally leading to distinct nanoscopic phases separated by an interface, as in simulations which started with a preformed interface, but the IL phase is more humid. The final state of water in the IL thus depends on the protocol and relates to IL heterogeneities and viscosity. Water mainly fluctuates in hydrophilic basins (rich in O(Tf2N) and aromatic CH(BMI) groups), separated by more hydrophobic domains (rich in CF3(Tf2N) and alkyl(BMI) groups), in the form of monomers and dimers in the weakly humid IL phase, and as higher aggregates when the IL phase is more humid. There is more water in the IL than IL in water, to different extents, depending on the model. The interface is sharper and narrower (approximately 10 A) than with the less hydrophobic [BMI][PF6] IL and is overall neutral, with isotropically oriented molecules, as in the bulk phases. The results allow us to better understand the analogies and differences of aqueous interfaces with hydrophobic (but hygroscopic) ILs, compared to classical organic liquids.     

pH-selective synthesis and structures of alkynyl, acyl, and ketonyl intermediates in anti-Markovnikov and Markovnikov hydrations of a terminal alkyne with a water-soluble iridium aqua complex in water

Chemoselective synthesis and isolation of alkynyl [Cp*Ir(III)(bpy)CCPh]+ (2, Cp* = eta5-C5Me5, bpy = 2,2'-bipyridine), acyl [Cp*Ir(III)(bpy)C(O)CH2Ph]+ (3), and ketonyl [Cp*Ir(III)(bpy)CH2C(O)Ph]+ (4) intermediates in anti-Markovnikov and Markovnikov hydration of phenylacetylene in water have been achieved by changing the pH of the solution of a water-soluble aqua complex [Cp*Ir(III)(bpy)(H2O)]2+ (1) used as the same starting complex. The alkynyl complex [2]2.SO4 was synthesized at pH 8 in the reaction of 1.SO4 with H2O at 25 degrees C, and was isolated as a yellow powder of 2.X (X = CF3SO3 or PF6) by exchanging the counteranion at pH 8. The acyl complex [3]2.SO4 was synthesized by changing the pH of the aqueous solution of [2]2.SO4 from 8 to 1 at 25 degrees C, and was isolated as a red powder of 3.PF6 by exchanging the counteranion at pH 1. The hydration of phenylacetylene with 1.SO4 at pH 4 at 25 degrees C gave a mixture of [2]2.SO4 and [4]2.SO4. After the counteranion was exchanged from SO4(2-) to CF3SO3-, the ketonyl complex 4.CF3SO3 was separated from the mixture of 2.CF3SO3 and 4.CF3SO3 because of the difference in solubility at pH 4 in water. The structures of 2-4 were established by IR with 13C-labeled phenylacetylene (Ph12C13CH), electrospray ionization mass spectrometry (ESI-MS), and NMR studies including 1H, 13C, distortionless enhancement by polarization transfer (DEPT), and correlation spectroscopy (COSY) experiments. The structures of 2.PF6 and 3.PF6 were unequivocally determined by X-ray analysis. Protonation of 3 and 4 gave an aldehyde (phenylacetaldehyde) and a ketone (acetophenone), respectively. Mechanism of the pH-selective anti-Markovnikov vs Markovnikov hydration has been discussed based on the effect of pH on the formation of 2-4. The origins of the alkynyl, acyl, and ketonyl ligands of 2-4 were determined by isotopic labeling experiments with D2O and H2(18)O.     

Multiple mixed-valence behavior in trans,trans-[(tpy)(Cl)2Os(III)(mu-1,3-N3)Os(III)(Cl)2(tpy)]+. An azido bridge from the reaction between trans-[Os(VI)(tpy)(Cl)2(N)]+ and NH3

Reaction between the Os(VI)-nitrido complex, trans-[OsVI(tpy)(Cl)2(N)]PF6 (tpy = 2,2':6',2' '-terpyridine), and ammonia (NH3) under N2 in dry CH3CN gives the mu-1,3-azido bridged [OsII-N3-OsII]- dimer, trans,trans-NH4[(tpy)(Cl)2OsII(N3)OsII(Cl)2(tpy)]. It undergoes air oxidation to give the [OsIII-N3-OsIII]+ analogue, trans,trans-[(tpy)(Cl)2OsIII(N3)OsIII(Cl)2(tpy)]PF6 ([OsIII-N3-OsIII]PF6), which has been isolated and characterized. The structural formulation as a mu-1,3-N3 bridged complex has been established by infrared and 15N NMR measurements on the 15N-labeled forms, [OsIII-14N=15N=14N-OsIII]+, [OsIII-15N=14N=15N-OsIII]+, and [OsIII-15N=15N=15N-OsIII]+. Cyclic voltammetric measurements in 0.2 M Bu4NPF6/CH3CN reveal the existence of five chemically reversible waves from 1.40 to -0.12 V for couples ranging from OsV-OsIV/OsIV-OsIV to OsIII-OsII/OsII-OsII. DeltaE1/2 values for couples adjacent to the three mixed-valence forms are 0.19 V for OsIII-OsII, 0.52 V for OsIV-OsIII, and >0.71 V for OsV-OsIV. In CH3CN at 60 degrees C, [OsIII-N3-OsIII]+ undergoes a [2 + 3] cycloaddition with CH3CN at the mu-N3- bridge followed by a solvolysis to give trans-[OsIII(tpy)(Cl)2(5-MeCN4)] and trans-[OsIII(tpy)(Cl)2(NCCH3)]PF6.     

Homoleptic alkaline earth metal bis(trifluoromethanesulfonyl)imide complex compounds obtained from an ionic liquid

The first homoleptic alkaline earth bis(trifluoromethanesulfonyl)imide (Tf2N) complexes [mppyr]2[Ca(Tf2N)4], [mppyr]2[Sr(Tf2N)4], and [mppyr][Ba(Tf2N)3] were crystallized from a solution of the respective alkaline earth bis(trifluoromethanesulfonyl)imide and the ionic liquid [mppyr][Tf2N] (mppyr = 1,1-N-methyl-N-propylpyrrolidinium). In the calcium and strontium compounds, the alkaline earth metal (AE) is coordinated by four bidentately chelating Tf2N ligands to form isolated (distorted) square antiprismatic [AE(Tf2N)4]2- complexes which are separated by N-methyl-N-propylpyrrolidinium cations. In contrast, the barium compound, [mppyr][Ba(Tf2N)3], forms an extended structure. Here the alkaline earth cation is surrounded by six oxygen atoms belonging to three Tf2N- anions which coordinate in a bidentate chelating fashion. Three further oxygen atoms of the same ligands are linking the Ba2+ cations to infinite (infinity)(1)[Ba(Tf2N)3] chains.     

Detection of new radiolysis products in γ-irradiated,methanolic medazepam by GC-FTIR

Summary A methanolic solution of 2% medazepam was irradiated with a dose of 50 kGy. A capillary gas chromatograph with a Fourier Transformation Infrared Spectrophotometer (FTIR) was used to investigate the radiolysis products in the solution. The changed products found earlier were confirmed and new ones identified. The radiolytic scheme can be improved and enlarged.     

Structural characterization of a lanthanum bistriflimide complex, La(N(SO2CF3)2)3(H2O)3, and an investigation of La, Sm, and Eu electrochemistry in a room-temperature ionic liquid, [Me3N(n)Bu][N(SO2CF3)2

The reduction of selected lanthanide cations to the zerovalent state in the room-temperature ionic liquid [Me3N(n)Bu][TFSI] is reported (where TFSI = bistriflimide, [N(SO2CF3)2]-). The lanthanide cations were introduced to the melt as the TFSI hydrate complexes [Ln(TFSI)3(H2O)3] (where Ln = La(III), Sm(III) or Eu(III)). The lanthanum compound [La(TFSI)3(H2O)3] has been crystallographically characterized, revealing the first structurally characterized f-element TFSI complex. The lanthanide in all three complexes was shown to be reducible to the metallic state in [Me3N(n)Bu][TFSI]. For both the Eu and Sm complexes, reduction to the metallic state was achieved via divalent species, and there was an additional observation of the electrodeposition of Eu metal.     

Development of cation/anion "interaction" scales for ionic liquids through ESI-MS measurements

Electrospray ionization mass spectrometry applied to ionic liquids allowed the study of loosely bonded supramolecules, originating from these organic salts. Based on the observation that ionic liquids formed cationic [C(q+1)X(q)](+) and anionic [C(q)X(q+1)](-) supramolecular aggregates, we have investigated mixed networks, formed by different cations coordinated to a selected anion or by different anions bonded to a given cation, i.e., [C1...X...C2](+) and [X1...C...X2](-), with the aim to build a scale of the cation-anion interaction strength. The qualitative order of intrinsic bond strength to Br- was found to be the following: [emim](+) > [bmim](+) > [mor1,2](+) > [hmim]+ > [omim](+) > [mor1,4](+) > [bupy](+) > [bpyrr](+) > [picol](+) > [bm(2)im](+) > [TBA](+). Similarly, the interaction energies to 1-butyl-3-methylimidazolium (bmim) species envisaged two classes of anions: species tightly coordinated to the cationic moiety that include CF3COO(-), Br(-), N(CN)2(-), and BF4(-) and anions loosely interacting with the alkylimidazolium species such as OTf(-), PF6(-), and Tf2N(-).     

Size-controllable gold-platinum alloy nanoparticles on nine functionalized ionic-liquid surfaces and their application as electrocatalysts for hydrogen peroxide reduction

A series of room-temperature ionic liquids (RTILs) containing different functional groups such as hydroxyl, nitrile, carboxyl, and thiol attached to imidazolium cations, combined with various anions such as chloride [Cl], tetrafluoroborate [BF(4)], hexafluorophosphate [PF(6)], and bis[(trifluoromethyl)sulfonyl]imide [Tf(2)N], have been successfully synthesized. Dissolved in chitosan (Chi), the Chi/RTIL composites can be employed as flexible templates for the preparation of Au/Pt nanostructures. These Au/Pt nanostructures can be facilely deposited in situ on the surface of Chi/RTILs through electrodeposition. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) results demonstrate that the alloy size is significantly dependent on the structure of the Chi/RTILs, with sizes ranging from 2.8 to 84.7 nm. Based upon the functionalized RTILs, nine Chi/RTIL-Au/Pt biosensors have been fabricated. First, the size-dependent electrochemistry of Chi/RTIL-Au/Pt was investigated using potassium ferricyanide as the probe. The reversible electron transfer of the Fe(CN)(6)(3-/4-) redox couple was realized for the nine biosensors, and the peak currents, as well as the peak-to-peak separations (ΔE(p)) and electron-transfer rates, differ greatly from each other because of the diversity of the RTILs. Further electrochemical research reveals that the functional groups of these RTILs exert an evident influence on the reduction behavior of H(2)O(2), which in turn illustrates that the electrocatalytic activity of Chi/RTIL-Au/Pt nanocomposites can be tuned by means of employing RTILs with different functional groups, and an appropriate combination of cations and anions may produce a higher activity. The facilitated electron transfer and the intrinsic catalytic activity of Au/Pt NPs provide a facile way to construct a third-generation H(2)O(2) biosensor with a high sensitivity, low detection limit, quick response time, and excellent selectivity.     

Synthesis, characterization, and substitution chemistry of [Bu4N]2[W6Cl8(OSO2CF3)6]. A versatile precursor for axially substituted clusters containing the (W6Cl8)4+ core

The new cluster [Bu4N]2[W6Cl8(OSO2CF3)6] (1) has been prepared and structurally characterized. This material is an effective precursor for the generation of cluster ions with the general formula [W6C18L6]n (L = Cl-, Br-, I-, NCS-, NCO-, NCSe-, and O=PPh3; n = 2- or 4+). The last three clusters are new. The products have been characterized by IR spectroscopy, NMR spectroscopy, and FAB mass spectrometry. In addition to 1, the products [Bu4N]2[W6C18(NCS)6] (5) and [Bu4N]2[W6C18(NCO)6] (7) were structurally characterized. Crystal data for 1: space group, P2(1/c) (No. 14); a = 11.116(5) A; b = 27.952(1) A; c = 24.516(1) A; beta = 95.182(9) degrees; V = 7586.3(5) A3; Z = 4. Crystal data for 5: space group, P2(1/n) (No. 14); a = 11.3323(9) A; b = 12.3404(9) A; c = 44.583(3) A; beta = 97.089(1) degrees ; V = 6187.1(7) A3; Z = 4. Crystal data for 7: space group, P1 (No. 2); a = 11.8009(8) A; b = 11.9332(8) A; c = 11.9522(8) A; alpha = 77.904(1) degrees; beta = 95.182(9) degrees; gamma = 62.574(1) degrees V = 1450.5(2) A3; Z = 1.