熔体插层制备尼龙6/蒙脱土纳米复合材料的性能表征

通过熔体插层成功地制备了尼龙６／蒙脱土纳米复合材料，测试了力学性能、耐热性能和耐溶剂性．通过ＴＥＭ、ＷＡＸＤ、ＤＳＣ等手段，研究了结构与结晶行为，并与插层聚合的尼龙６／蒙脱土纳米复合材料进行了对比．实验表明通过熔体插层可使尼龙６基体插层于蒙脱土中，所得到的复合物的性能较尼龙６有很大提高，且与插层聚合的尼龙６／蒙脱土纳米复合材料的性能相当．     

尼龙6/蒙脱土纳米复合材料的等温结晶动力学研究

用ＤＳＣ法研究了熔体插层制备的尼龙６／蒙脱土纳米复合材料的等温结晶行为．结果表明,加入少量的蒙脱土可明显提高尼龙６的结晶速率,降低球晶径向生长的单位面积表面自由能．从Ａｖｒａｍｉ方程和Ｈｏｆｍａｎ理论出发,得出蒙脱土纳米粒子的存在可明显改变尼龙６的结晶行为     

聚对苯二甲酸乙二酯/蒙脱土纳米复合材料的制备和性能

讨论了聚对苯二甲酸乙二醇酯（ＰＥＴ）／层状硅酸盐（蒙脱土）纳米复合材料的制备技术和新材料的结构与性能特征．天然蒙脱土矿物经有机离子修饰剂处理后,参与ＰＥＴ的缩聚反应．ＴＥＭ测定证实蒙脱土在ＰＥＴ中的层厚分布为３０～５０ｎｍ．蒙脱土不影响ＰＥＴ的分子量及其分布．利用ＤＳＣ、ＷＡＸＤ、ＳＡＬＳ和偏光显微镜测定了ＰＥＴ／蒙脱土的结晶速率和结晶形态,说明ＰＥＴ／蒙脱土有着很快的结晶速率,不能生成球晶结构,一般只能生成结构不完整的微晶体．ＰＥＴ／蒙脱土在工程塑料和工业纤维领域有潜在的应用前景     

甲苯—2,4—二异氰酸酯修饰蒙脱土及聚苯乙烯／蒙脱土纳米复合材料？…

用ＦＴＩＲ和ＷＡＸＤ法研究了甲苯－２，４－二异氰酸酯（ＴＤＩ）的邻位和对位异氰酸酯基因与蒙脱土表面羟基的修饰反应，在此基础上提出了结构模型；用ＴＤＩ修饰后的蒙脱土成功制备了插层型聚苯乙烯／蒙脱土纳米复合材料，并用ＷＡＸＤ和ＴＥＭ进行了表征。实验结果表明，修饰后ＴＤＩ与蒙脱土表面形成化学键，使蒙脱土的片层间距显著增大，十六烷基三甲基溴化铵（ＣＴＡＢ）在蒙脱土层间由双层平行排列转变为双层脂肪链倾斜方式     

蒙脱土修饰电极上某些神经递质的电化学行为

采用不同电化学方法对神经递质多巴胺（ＤＡ）在蒙脱土修饰电极上的行为进行了研究，结果发现，蒙脱土修饰膜地ＤＡ有明显的富集作用。在ＰＨ７．４时，ＤＡ强烈地富集在蒙脱土膜内，并显示完成的伏安响应而抗坏血酸（ＡＡ）和ＤＡＲ的代谢产物３，４－二羟基苯乙酸（ＤＯＰＡＣ）则无任何响应。采用计时库仑法测定了ＤＡ在蒙脱土膜内的表观扩散系数为２．３×１０＾－９ｃｍ＾２／ｓ，并计算了异相速率常数为２．７×１０＾－６ｃｍ     

尼龙6/蒙脱土纳米复合材料非等温结晶动力学和透明性研究

将有机化的蒙脱土与尼龙6(PA6)在Haake共混机中共混,制备出尼龙6/蒙脱土纳米复合材料(PA6N);对尼龙6/蒙脱土纳米复合材料和纯尼龙6分别进行差示扫描量热法非等温结晶试验,以了解蒙脱土在尼龙6/蒙脱土纳米复合材料中的成核作用、扩大尼龙6在包装领域的应用范围.与此同时,采用偏光显微镜测定了样品的结晶形态;采用紫...     

尼龙6/蒙脱土纳米复合材料的制备、结构与力学性能的研究

未经处理及经１１ 氨基酸处理的蒙脱土由于己内酰胺的引入而发生膨胀．己内酰氨可以在蒙脱土的硅酸盐片层间聚合，形成尼龙６／蒙脱土纳米复合材料．经１１ 氨基酸处理的蒙脱土和尼龙６分子间有很强的化学相互作用．与未经处理的蒙脱土相比，其所构成的纳米复合材料具有很好的力学性能．     

聚氧化乙烯/蒙脱土纳米嵌入化合物的制备与结构表征

利用溶液法和熔融法制备聚氧化乙烯（ＰＥＯ）／蒙脱土纳米嵌入化合物,用ＸＲＤ,ＩＲ和ＤＳＣ等测试手段对嵌入化合物进行了表征。嵌入的ＰＥＯ分子同蒙脱土晶层中的Ｎａ＾＋生成ＰＥＯ－Ｎａ＾＋络合物,嵌入化合物具有一定的耐溶剂萃取剂,ＰＥＯ分子以单层螺旋构象排列于蒙脱土的晶层中,ＰＥＯ分子在蒙脱土层间运动受到限制,致使嵌入化合物的结晶熔融峰减弱。     

尼龙11在高压下的结晶研究

用ＤＳＣ、ＷＡＸＤ、ＩＲ等对在０．１ＭＰａ－０．６５ＧＰａ压力下尼龙１１（ＰＡ１１）的结晶样品进行了研究。分析了压力对ＰＡ１１结晶的影响。研究了加入１％液晶聚合物对ＰＡ１１的结晶的诱导作用。结果表明：压力有助于ＰＡ１１晶形的完善，液晶聚合物对ＰＡ１１的结晶有明显的诱导作用，使ＰＡ１１在较低的压力（０．１ＧＰａ）和较短的时间（１５ｍｉｎ）内即可得到较为完整的结晶。     

蒙脱土对尼龙66熔融与结晶行为的影响

通过DSC方法研究了蒙脱土对尼龙66熔融与结晶行为的影响，探讨了蒙脱土对尼龙66结晶的成核作用。发现有机蒙脱土使尼龙66的熔融峰温度Tm提高5.3℃，使结晶峰温度提高13－24℃，二次熔融多产生双重熔融峰，蒙脱土的加入有利于生成低温峰。     

尼龙66/蒙脱土复合材料结晶行为的研究

在密炼机中采用熔融共混法制备蒙脱土重量分数为 2 5 %、4 5 %的尼龙 6 6 /蒙脱土复合材料 .通过DSC法对非等温结晶行为及在 2 2 8～ 2 4 0℃范围内的等温结晶行为进行研究 ,并与纯尼龙 6 6进行比较 .从其等温和非等温结晶行为的研究表明 ,蒙脱土起成核剂的作用 ,它的填入使尼龙 6 6结晶速率提高 ,但填料与基体间的相互作用使其链段运动困难 ,结晶活化能提高 ;在研究的填料含量变化范围内 ,结晶行为变化不大 ,并且找到该复合材料在 2 2 8～ 2 34℃范围结晶对温度的不敏感区 ;对非等温结晶过程分析 ,刘结平 莫志深方程是适用的 ,而Ozawa方程则是不适用的 .     

One-pot synthesis of nylon 6–clay hybrid

Nylon 6–clay hybrid is a molecular composite of nylon 6 and uniformly dispersed silicate layers of montmorillonite. One-pot synthesis of the hybrid was carried out by the following procedures. Montmorillonite was dispersed in water, and then ε-caprolactam, acid (phosphoric acid, hydrochloric acid, benzenesulfonic acid, isophthalic acid, trichloroacetic acid, or acetic acid), and 6-aminocaproic acid were added to the dispersion. The mixtures were reacted at 260°C for 6 h, yielding the nylon 6–clay hybrids (1potNCHs). X-ray diffraction revealed that the silicate layers of 1potNCH by phosphoric acid were uniformly dispersed in the nylon 6 matrix. The 1potNCH had excellent mechanical properties. The strength and the modulus of the hybrid increased compared with previously reported nylon 6–clay hybrid (NCH) synthesized by montmorillonite intercalated with 12-aminolauric acid. The heat distortion temperature (HDT) of the 1potNCH was 160°C, which was 8°C higher than that of NCH. In other 1potNCHs, montmorillonite had a smaller effect on the increase of those properties, and interlayer spacing of montmorillonite was observed at ca. 20 Å. © 1993 John Wiley & Sons, Inc.     

尼龙1212/尼龙6共混体系的非等温结晶行为

用DSC研究了尼龙 12 12 ,尼龙 6及其共混体系的非等温结晶行为 .结果表明 ,加工历史对尼龙的结晶和熔融行为影响很大 .经双螺杆挤出机挤出的尼龙 12 12和尼龙 6 ,由于应力诱导分子链取向 ,其结晶温度都有不同程度的提高 ,且表现出多重熔融现象 .在共混体系中 ,尼龙 12 12分子在共混物的界面上异相成核结晶 ,提高了其结晶温度 ,但酸酐化SEBS的加入抑制了分子链的运动又使其结晶温度降低 .共混体系降低了尼龙12 12的熔融温度 ,并使得其高熔点的熔融峰逐渐消失 ;而尼龙 6的熔融行为基本上没有变化 .     

聚对苯甲酰胺存在下尼龙6的结晶化

用解偏振光强度法和DSC等方法研究了少量聚对苯甲酰胺(PBA)对尼龙6结晶化过程和热行为的影响.利用Avrami方程处理解偏振光强度法的实验结果,得到了尼龙6及含PBA 1%、2%尼龙6的n值分别为3.3、1.6、1.7.DSC结果表明,尼龙6中掺入少量的PBA会使结晶度提高,X射线衍射显示,当尼龙6中加入少量PBA后,晶格结构并未改变。     

Synthesis of nylon 6–clay hybrid by montmorillonite intercalated with ϵ-caprolactam

It was found that montmorillonite was intercalated with ?-caprolactam. X-ray diffraction revealed that the chain axes of the ?-caprolactam were parallel to the montmorillonite plates. The intercalated montmorillonite was swollen by molten ?-caprolactam at 200°C. ?-Caprolactam and 6-aminocaproic acid (accelerator) were polymerized with the intercalated montmorillonite at 260°C for 6 h, yielding a nylon 6-clay hybrid. X-ray diffraction and transmission electron micrography revealed that the silicate layers of the hybrid were uniformly dispersed in the nylon 6 matrix. Mechanical properties of the hybrid were improved. The strength and the modulus of the hybrid increased compared with the previously reported nylon 6 clay-hybrid (NCH) synthesized by montmorillonite intercalated with 12-aminolauric acid. The heat distortion temperature (HDT) of the hybrid was 164°C, which was 12°C higher than that of NCH. © 1993 John Wiley & Sons, Inc.     

尼龙6/(乙烯-辛烯)共聚物弹性体的流变及结晶行为

（乙烯 辛烯）共聚物弹性体（ＰＯＥ）是由美国ＤＯＷ化学公司使用茂金属催化剂聚合而成的一种聚烯烃橡胶．与传统聚烯烃类橡胶ＥＰＤＭ相比,ＰＯＥ的特点就在于其在聚烯烃塑料基体中分散速度快、分散程度高．为此,我们尝试用马来酸酐接枝的ＰＯＥ（ＰＯＥ ｇ ＭＡ）...     

Investigation on nonisothermal crystallization kinetics of the high‐flow nylon 6 by differential scanning calorimetry

The crystallization kinetics of the high‐flow nylon 6 containing polyamidoamine (PAMAM) dendrimers units in nylon 6 matrix was investigated by differential scanning calorimetry. The Ozawa and Mo equations were used to describe the crystallization kinetics under nonisothermal condition. The values of Avrami exponent m and the cooling crystallization function F(T) were determined from the Ozawa plots, which showed bad linearity, and were divided into three sections depending on different cooling rates. The plots of the m and log F(T) values versus crystallization temperatures were obtained, which indicated that the actual crystallization mechanisms might change with the crystallization temperatures. The high‐flow nylon 6 has higher values of m and log F(T) than those of pure nylon 6, which implied that the high‐flow nylon 6 had more complicated crystallization mechanisms and slower crystallization rate than those of pure nylon 6. The good linearity of the Mo plots verified the success of this combined approach. The activation energies of the high‐flow nylon 6 ranged from 157 to 174 kJ/mol, which were determined by the Kissinger method. The ΔE values were lower than those of pure nylon 6, and the ΔE values were affected by both the generation and the content of PAMAM units in the nylon 6 matrix. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2201–2211, 2008