流化床快速制不定形活性焦脱除烟气中SO2的研究

利用大型流化床制得了适用于脱除烟道气中二氧化硫的不定形活性焦AC-A，并对其进行了特性分析，在固定床上考察了不同条件下脱除SO2的性能。与硫容相近的商业活性焦AC-B的脱硫性能对比，发现其脱硫性能较好。实验结果表明，在烟气中的二氧化硫的体积分数为0.05%~0.12%，反应温度为80 ℃～100 ℃，空速（GHSV）为1 200 h-1，O2的体积分数为6%，水蒸气为10%的情况下，活性焦AC-A保持SO2脱除率在90%以上达5 h。再生循环脱硫实验表明，活性焦AC-A具有良好的再生脱硫活性。     

同时脱除烟气中硫和硝的V2O5/AC催化剂研究

通过在固定床微反应器上对同时脱硫脱硝催化剂的研究，发现将V2O5担载在活性焦(AC)上制得的V2O5/AC催化剂可在200 ℃同时脱除烟气中的SO2和NO，其活性明显高于纯AC。V2O5/AC催化剂的脱硫脱硝活性与催化剂中钒的质量分数有关，随着V2O5质量分数从0.5%增至9%，硫容从3%增加到12%，脱硝率在V2O5质量分数为0.5%到3%时脱硝率稳定在60%左右，继续增加V2O5质量分数，脱硝率降低。程序升温脱附 (TPD) 和红外光谱 (FTIR) 表征结果显示在脱硫脱硝过程中，催化剂表面有H2SO4, 铵盐和VOSO4生成, VOSO4的质量分数随催化剂中V2O5质量分数的提高而升高。使用后的催化剂可通过5%NH3在300 ℃再生，再生后催化剂的脱硝活性明显增加，NO转化率从新鲜样的67%提高到接近100%，对SO2的吸附也比新鲜样有所增加。     

V2O5-CeO2/TiO2催化剂上低温氨选择性催化还原NO的性能

考察了V2O5-CeO2/TiO2催化剂中V、Ce活性组分的担载量和焙烧温度对催化剂低温催化还原NO活性的影响及其在单独SO2、H2O和两者共存气氛下的抗毒化性能。结果表明,焙烧温度400℃下制备的5V30Ce/TiO2催化剂具有良好的低温催化还原NO活性,空速为10000h-1,165℃时NO转化率达99.2%;500℃以下低焙烧温度时,添加的Ce不与V相互作用,在催化剂表面主要以CeO2形式存在,有利于增大催化剂比表面积,增强V2O5在催化剂上的分散度,提高催化活性。而在500℃以上较高焙烧温度下,Ce与V会形成CeVO4,对活性提高不利。催化剂具有良好的低温抗水中毒性能,但受SO2毒化作用明显,其在SO2、H2O共存气氛下中毒程度较单独SO2下浅。     

炭化温度对飞焦和煤混合原料制成型活性焦性能的影响

以中国科学院山西煤炭化学研究所灰熔聚流化床粉煤气化工业示范试验二旋飞焦为部分原料，再配以原煤和煤焦油混合，试制了烟气脱硫用成型活性焦。实验表明: 炭化温度的高低对成型活性焦的性能有很大的影响，其中对强度的影响尤为密切。为了得到较高的耐磨、耐压强度，在满足其它性能的前提下，炭化温度最佳的范围为600 ℃～700 ℃,在此条件下制得的活性焦其强度大于95%, 硫容为80 mg/g，符合活性焦的商业使用要求。同时研究了炭化温度对活性焦孔结构发展的影响。并对活性焦进行了孔结构的表征，探讨了孔结构和二氧化硫吸附性能的关系。     

Mn-V-Ce/TiO_2低温催化还原NO性能研究

采用浸渍法制备了NH3选择性催化还原(SCR)NO新型催化剂Mn-V-Ce/TiO2,考察了操作条件对其活性的影响;通过NO、O2、NH3的暂态响应实验分析了在该催化剂上进行SCR反应的机理;对催化剂进行了FT-IR和TG分析,探讨了H2O、SO2对其活性的影响。结果表明,该催化剂具有很好的低温SCR活性,空速5 000 h-1、150℃下的NO转化率达99.2%。170℃下同时通硫、水后的350 min内,活性始终保持在98%;单独通入SO2时,中毒速率较快,但体积分数为8%的H2O对该催化剂的活性没有影响,转化率始终保持在98%以上。该催化剂能应用于不含SO2的燃气锅炉烟气和不含SO2的硝酸尾气等NOx工业废气的低温脱硝。     

煤制活性焦性质对其脱除烟道气中二氧化硫性能的影响

讨论了四种煤制活性焦的性质对其脱除烟道气中SO2性能的影响,活性焦的表面碱性与微孔面积决定了其对烟道气中SO2的吸附与氧化。生成的硫酸主要贮存在活性焦的微孔内。活性焦内的硫酸在脱附温度为300℃时达到最大脱附速率。     

反应气氛中二氧化硫存在下La_(0.8)K_(0.2)Mn_(0.95)Cu_(0.05)O_3催化剂对碳烟的氧化

利用La0.8K0.2Mn0.95Cu0.05O3氧化模拟碳烟,考察预硫化处理及程序升温氧化中SO2对催化剂性能的影响。采用H2-TPR,FTIR和XPS等方法对催化剂性能进行了表征。XPS表明催化剂在0.02%SO2气氛中400℃下进行4 h的预硫化后OI(O2-)转化为OII(O-),催化剂活性增加;TPO反应中低浓度SO2(0.01%)促进了催化剂的活性,可能是较高温度下高活性K的存在,有效阻止了硫酸盐的生成及积累,对O-的消耗减少。催化剂在0.02%SO2气氛中300℃下预硫化超过1 h以后活性明显降低,预硫化1.5 h后催化剂表面的O2-几乎消耗完全,O-大大减少,二者都转化为O(O2-);可能是较低温度下硫酸盐逐渐积累,加快了O2-的消耗,导致可用的氧源枯竭,催化剂活性降低。     

用CuO／γ－Al2O3催化剂同时脱除烟气中的SO2和NO

 研究了用CuO／γ－Al2O3催化剂同时脱除烟气中的SO2和NO，并在固定床反应器中考察了反应条件对其催化活性的影响．结果表明，温度和SO2对CuO／γ－Al2O3的催化活性均具有双重影响．新鲜催化剂和硫化催化剂上最适宜的脱硝温度分别为250～300℃和300～450℃，最适宜的n（NH3）／n（NO）约为1．2．烟气中的氧可大大提高CuO／γ－Al2O3的脱硫脱硝活性．综合考虑吸附硫容和NO脱除率，CuO／γ－Al2O3同时脱硫脱硝的最适宜温度为350～450℃．温度和SO2在高温区对CuO／γ－Al2O3活性的影响源于两者对NH3氧化活性的改变，高温下CuO／γ－Al2O3的活性下降是因为NH3氧化加剧；SO2通过使催化剂硫化生成硫酸盐来抑制NH3氧化，从而提高CuO／γ－Al2O3的活性．吸硫饱和的催化剂可于5％NH3中还原再生，再生后其硫容较初始时降低，但其活性大幅度提高．     

热处理改性活性炭纤维的脱硫活性

 考察了在O2和水蒸气存在下高温热处理对活性炭纤维（ACF）催化转化SO2为H2SO4的活性的影响,关联了ACF表面含氧官能团的种类及数量与热处理后ACF的脱硫活性之间的关系．结果表明,在最佳热处理温度下以CO形式释出的含氧官能团的总量决定了ACF的脱硫活性,而以CO2形式释出的含氧官能团未对提高ACF的脱硫活性做出贡献．通过采用不同的氧化剂改变ACF表面含氧官能团的种类和数量,进一步证实了热处理过程中释出的CO量与ACF的脱硫活性之间成正比关系．     

氨再生条件对V2O5/AC同时脱硫脱硝活性的影响

对烟气同时脱硫脱硝过程中吸附SO2后的活性炭载V2O5（V2O5/AC）催化 吸附剂在含NH3气氛下的再生条件进行了考察，发现3%～5%NH3/Ar气氛、300℃、60min再生可有效恢复V2O5/AC的脱硫活性，并明显提高其脱硝活性。基于对SO2和NO的脱除率、再生后V2O5/AC的硫质量分数以及FT IR谱图分析发现，NH3的存在对V2O5/AC所吸附硫的脱附行为没有明显影响，但可显著改变V2O5/AC的表面化学性质，有利于烟气脱硫；NH3还可在V2O5/AC表面储存，显著促进脱硝。     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.     

Synthesis of N-substituted carbazolones from α-iodo enaminones via Pd(0)-catalyzed intramolecular coupling under microwave irradiation

A variety of N-aryl and N-alkyl carbazolones were conveniently achieved in good to high yields via Pd₂(dba)₃-mediated intramolecular coupling of N-substituted α-iodo enaminones under microwave irradiation. The Pd(0)-catalyzed cyclization was found to proceed favorably with the more electron-deficient phenyl ring during the reactions involving unsymmetrical N,N-diaryl α-iodo enaminones. This unique property enables the construction of carbazolone skeleton containing nitro substituted benzenoid ring.     

Synthesis of substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles by intramolecular nitrilimine cycloaddition

Both substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles have been synthesized by the 3+2 intramolecular dipolar cycloaddition of nitrilimines to alkynes. This cyclization has been extended to more versatile 3-bromo derivatives by the use of alkynylbromides as dipolarophiles.     

Catalyst free,visible-light promoted photoaddition reactions between C60 and N-trimethylsilylmethyl-substituted tertiary amines for synthesis of aminomethyl-1,2-dihydrofullerenes

An efficient and benign method for the preparation of aminomethyl-substituted fullerenes has been developed. The process, involving catalyst free, visible-light irradiation of 10% EtOH-toluene solutions containing fullerene C₆₀ and N-trimethylsilylmethyl-substituted amines by using a 20 W compact fluorescent lamp, leads to formation of aminomethyl-substituted fullerene adducts in a highly efficient manner. The photoaddition reaction takes place via a pathway initiated by visible light absorption by C₆₀, followed by SET from the amine to the triplet excited state of C₆₀. Ethanol-promoted desilylation of the resulting a minimum radical then generates the corresponding α-amino radical which couples with the C₆₀ radical anion to form the anion precursor of the fullerene adducts. The new approach using visible-light takes place under mild conditions and it does not require the use of photocatalysts. Thus, the method developed in this effort could broadens the range of functionalized fullerene derivatives that can be readily prepared.     

Highly efficient and stereoselective cycloaddition of nitrones to indolyl- and pyrrolylacrylates

The reactions of various nitrones with indolyl- and pyrrolylacrylates proceeds regioselectively with high diastereoselectivity in the case of aldonitrones, and represents an effective method for obtaining new indolyl- and pyrrolyl-substituted isoxazolidine carboxylates stabilized by weak (CH?O) and moderate (NH?N) strength intramolecular hydrogen bonding. The resulting cycloadducts exhibit promising in vitro anti-influenza activities.     

Transition metal-free direct amination of benzoxazoles using formamides as nitrogen sources

A transition metal-free method for the direct amination of benzoxazoles using formamides as nitrogen sources is reported, which was mediated by an inexpensive and environmentally friendly tetrabutylammonium iodide/tert-butyl hydroperoxide system and gave the 2-aminobenzoxazole derivatives with moderate to good yields.     

l-Proline-catalyzed five-component domino reaction leading to multifunctionalized 1,2,3,4-tetrahydropyridines

Multifunctionalized 1,2,3,4-tetrahydropyridines are concisely synthesized in good yields via l-proline-catalyzed or l-proline/FeCl₃-cocatalyzed one-pot multicomponent reactions (MCRs). The MCRs involve a domino hydroamination/prins reaction/Mannich-type reaction/intramolecular dehydration-cyclization process. The molecular structure of 5baa, one of multifunctionalized 1,2,3,4-tetrahydropyridines, was confirmed by single-crystal X-ray diffraction.     

Exploring the scope of the Gewald reaction: Expansion to a four-component process

An efficient four-component reaction was developed to take advantage of the reactivity of the 2-aminothiophene-3-carbonitrile functionality, which is obtained during the classical three-component Gewald reaction. Various α-methylene bearing ketones were reacted with malononitrile, elemental sulfur, and aryl/heteroarylnitrile derivatives in t-BuOH/NaOH to afford 2-arylthieno[2,3-d]pyrimidin-4-amines in high yields. Preliminary studies revealed the photophysical properties of the products and their potential for use as metal sensors.