Preparation and Properties of Novel Aromatic Polyamides from Diamines Containing 4,5-Imidazolediyl Structure

Novel aromatic polyamides were prepared from aromatic diamine containing 4,5-imidazolediyl unit, either by low temperature solution polycondensation or by direct polycondensation. Used diamines were 4,5-bis(4-aminophenyl)-2-phenylimidazole 1, 4,5-bis[4-(4-aminophenyl)]-2-(4-methylphenyl)imidazole 2 and 4,5-bis[4-(4-aminophenoxy)phenyl]-2-phenylimidazole 3. The obtained aromatic polyamides were produced with moderate to high inherent viscosity and soluble in polar aprotic solvents such as N,N-dimethylacetamide (DMAc), 1-methyl-2-pyrrolidone (NMP), N,N-dimethylformamide (DMF) and dimethyl sulfoxide (DMSO). Thermogravimetric analysis showed those polymers were stable up to 422°C in nitrogen atmosphere. The glass transition temperature (T _g)s of the polymers derived from diamine 3 were in the range between 243 and 275°C, and these values were approximately 120–160°C lower than those analogue polyamide I series containing no phenoxy units. The properties of polyamide I series are also compared with those of analogue polymers that order of aromatic nuclei and amide linkage is reversible.     

Polyamides of 2,5-bis(amino methyl) 1,4-dioxane and dicarboxylic acids

Novel polyamides of 2,5-bis(amino methyl) 1,4-dioxane (cis/trans-BAMD) with adipic/sebacic acids and of 2,5-bis(carboxy methyl)/2,5-bis(carboxy) 1,4-dioxane with 1,6-hexane diamine have been prepared. Because of the slightly higher conformational flexibility of the 1,4-dioxane ring in comparison with that of the cyclohexane ring, the BAMD polyamides have lower T_g and T_m than the corresponding 1,4-bis(amino methyl) cyclohexane (BAMC) polyamides. The symmetry of the trans-dioxane moiety permits high crystallinity in the trans-BAMD polymers. The crystallinity T_g and T_m of the trans polymers are decreased with the incorporation of the cis-dioxane moiety which lacks a plane of symmetry. Because of the hydrophilic nature of the dioxane ring, t-BAMD-6 has good moisture-regain properties, yet is melt processable (T_m = 292°C).     

Polyimide structure–property relationships. II. Polymers from isomeric diamines

An extensive study of the effects of stereoisomeric variations in aromatic polyimide structures on polyimide properties was conducted. The structural variations were incorporated into the polyimides through the use of two complete series of isomeric aromatic diamine monomers, the diaminodiphenylmethanes and the diaminobenzophenones, as well as several pairs of diamine isomers. The ability of the diamines to polymerize was related to the basicities, and thus reactivities, of the amino groups. Diamines with an amino group located ortho to the group connecting the two aromatic rings were successfully polymerized with dianhydrides for the first time to high molecular weight poly(amic acids). The stereoisomeric polyimides were characterized by determining the glass transition temperatures T_g, mechanical properties, and thermooxidative stabilities of thin films of the polymers. The polymers prepared from p-diamines were shown to have the highest softening points and thus, the most rigid molecular structures. Those synthesized from m-diamines had the lowest T_g values, inferring the most flexible molecular backbone. With limited exceptions, the use of diamines with ortho-oriented amine groups failed to improve the flexibility of the polyimides since their T_g values were usually as high as those of polymers made from p-diamines. Only slight differences in mechanical properties of the isomeric polyimide films were attributable to the variations in isomeric structure, except for those properties dependent upon T_g changes, such as elevated temperature mechanical properties. A study of the thermooxidative stability of the polyimides showed little difference between the polymers prepared from the diaminobenzophenones, but marked differences were observed between the individual members of the diaminodiphenylmethane-derived polyimides.     

Preparation and properties of silicon containing copolyamides

Copolyamides containing siloxane moieties in main chain were prepared by a melt polycondensation with 1,3-bis(3-aminopropyl)tetramethyldisiloxane (E), hexamethylenediamine (N6), and adipic acid (6). Glass transition temperature (T_g), cold crystallization temperature (T_cc), and melting temperature (T_m) were measured by differential thermal analysis (DTA). The depression of T_m for copolyamide was fitted by the Flory curve. Melting peak remarkably broadens with increasing E6 component in copolyamide. The change of T_g was fitted by the Gibbs and Dimarzio's equation in which the number of flexible bond is considered. The difference between T_g and T_cc increased with increasing E6 component. These DTA studies suggest that the crystallization of N66 component in copolyamide is hindered by the bulky siloxane moiety, while the micro-Brownian motion of amorphous segment is promoted by the flexible siloxane bond. Tensile strength and Young's modulus decreased with increasing E6 component. The solubility in various solvents increased with increasing E6 component. Permeability of oxygen and nitrogen increased with an increase of temperature and E6 component. The separation coefficient of oxygen to nitrogen rapidly increased near 50 mol% of E6 concentration and then leveled out above 70 mol%. The contact angle with water and methylene iodide increased with an introduction of the siloxane moiety into polymer chain.     

The preparation of novel silica modified polyimide membranes: synthesis,characterization, and gas separation properties

In this study, new monomers having siloxane groups were synthesized as an intermediate for preparation of siloxane modified polyimide polymers. Then with these monomers, the synthesis of uncrosslinked and crosslinked polyimide–siloxane hybrid polymer membranes were achieved. The purposes of the preparation of modified polyimides were to modify the thermal and chemical stability, and mechanical strength of polyimides, and to improve the gas separation properties of polymers. The new diamine monomer having siloxane groups was prepared from 3,5‐diaminobenzoic acid (3,5‐DABA) and 3‐aminopropyltrimethoxysilane (3‐APTMS) in N‐methyl‐2‐pyrollidone (NMP) at 180°C. The modified polyimide membranes having different amount of siloxane groups were synthesized from pyromellitic dianhydride (PMDA), 4,4‐oxydianiline (ODA), and 3,5‐diaminobenzamido‐N‐propyltrimethoxy silane (DABA/PTMS) in NMP using a two‐step thermal imidization process. The synthesis of modified polyimide membranes were characterized by Fourier transform infrared spectroscopy (FTIR). The thermal analysis of the polyimides were carried out by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Water absorption and swelling experiments were also carried out for the investigation of structural properties of polymers. FTIR observations confirmed that the polyimide membranes with new diamine intermediate were successfully obtained. Thermal analysis showed that the uncrosslinked copolyimides exhibited two glass transition temperatures, indicating that they were separated microphases and it was found that all the modified copolyimides had showed higher glass transition temperature (T_g) than unmodified polyimides. The separation properties of the prepared polyimide membranes were also characterized by permeability for O₂ and N₂ gases and ideal selectivity values were calculated. Copyright © 2009 John Wiley & Sons, Ltd.     

A macromonomer approach to the synthesis of poly(1,1‐bis(ethoxycarbonyl)‐2‐vinyl cyclopropane‐graft‐dimethyl siloxane)

Poly(1,1‐bis(ethoxycarbonyl)‐2‐vinyl cyclopropane (ECVP)‐graft‐dimethyl siloxane) copolymers were prepared using a macromonomer approach. Poly(dimethyl siloxane) (PDMS) macromonomers were prepared by living anionic polymerization of cyclosiloxanes followed by sequential chain‐end capping with allyl chloroformate. These macromonomers were then copolymerized with ECVP. MALDI‐ToF mass spectrometry and ¹H NMR spectroscopy were used to show that the macromonomers had approximately 80% of the end groups functionalized with allyl carbonate groups. Gradient polymer elution chromatography showed that high yields of the graft copolymers were obtained, along with only small fractions of the PECVP and PDMS homopolymers. Differential scanning calorimetry showed that the low glass transition temperature (T_g) of the PDMS component could be maintained in the graft copolymers. However, the T_g was a function of polymer composition and the polymers produced had T_gs that ranged from ?50 to ?120 °C. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Synthesis and properties of aromatic polyamides containing the cyclohexane structure

1,1-Bis[4-(4-carboxyphenoxy)phenyl]cyclohexane (III) and 1,1-bis[4-(4-aminophenoxy)phenyl]cyclohexane (V) were prepared in two main steps starting from the aromatic nucleophilic substitution of p-fluorobenzonitrile and p-chloronitrobenzene, respectively, with 1,1-bis(4-hydroxyphenyl)cyclohexane in the presence of potassium carbonate in N,N-dimethylformamide (DMF). Using triphenyl phosphite and pyridine as condensing agents, two series of polyamides with cyclohexylidene cardo groups were directly polycondensated from dicarboxylic acid III with various aromatic diamines or from diamine V with various aromatic dicarboxylic acids in an N-methyl-2-pyrrolidone (NMP) solution containing dissolved calcium chloride. The polyamides exhibited inherent viscosities in the range of 0.45 to 1.78 dL/g. Almost all of the polymers were readily soluble in polar aprotic solvents such as NMP and N,N-dimethylacetamide (DMAc) and could afford transparent, flexible, and tough films by solution casting. The glass transition temperatures (T_g) of these aromatic polyamides were in the range of 180–243°C by DSC, and the 10% weight loss temperatures in nitrogen and air were all above 450°C. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3575–3583, 1999     

Preparation and properties of new random and block copolyamides derived from 1,3-bis(3-aminopropyl)tetramethyldisiloxane,aromatic diamines,and isophthaloyl chloride

Random and block disiloxane-containing copolyamides were prepared through one- and two-step procedures, respectively, by the low temperature solution polycondensation in chloroform containing triethylamine hydrochloride starting from 1,3-bis(3-aminopropyl)tetramethyldisiloxane, an aromatic diamine [3,4'-diaminodiphenyl ether (ODA) or m-phenylenediamine], and isophthaloyl chloride. The random copolyamides exhibited composition-dependent single glass transition temperature (T_g), and gave transparent and tough films by solution casting or hot pressing. The ODA-based block copolyamides had two T_g's, and the solvent-cast transparent films exhibited microphase separated morphology. The block copolymers gave better quality films than the single-phase random copolymers. © 1992 John Wiley & Sons, Inc.     

Preparation and properties of novel soluble aromatic polyimides from 4,4′-diaminotriphenylamine and aromatic tetracarboxylic dianhydrides

New aromatic polyimides containing triphenylamine unit were prepared by two different methods, i.e., a conventional two-step method starting from 4,4′-diaminotriphenylamine and aromatic tetracarboxylic dianhydrides and the one-step thioanhydride method starting from the aromatic diamine and aromatic tetracarboxylic dithioanhydrides. Both procedures yielded high-molecular-weight polyimides with inherent viscosities of 0.47–1.17 dL/g. Some of these polymers were soluble in organic solvents such as N,N-dimethylacetamide, N-methyl-2-pyrrolidone, m-cresol, and pyridine. All the polyimides afforded transparent, flexible, and tough films, and the color varied from pale yellow to dark red, depending markedly on the tetracarboxylic acid components. The glass transition temperatures (T_gs) of these polyimides were in the range of 287–331°C and the 10% weight loss temperatures were above 520°C in air. The polyimides prepared by the one-step method exhibited better solubility in organic solvents and had somewhat lower T_gs than the polymers prepared by a conventional two-step method.     

Dynamic mechanical properties of aromatic,aliphatic, and partially fluorinated epoxy resins

The α, β, and γ transitions at temperatures between ?200 and +100°C. of crosslinked aromatic and aliphatic epoxy polymers were determined from damping and shear modulus data, and compared with their fluorine containing analogs. Loci of segmental relaxation are suggested at various temperatures, and similarities between aliphatic and fluorocarbon segments, and polyethylene and polytetrafluoroethylene are discussed. Two systems of structurally similar monomers 2,2,3,3,4,4-hexafluoropentane diglycidyl ether-1,5 and 1,4-butane diglycidyl ether, and 2,2-bis(4-glycidyl phenyl ether)hexafluoropropane and 2,2-bis(4-glycidyl phenyl ether) propane were polymerized with the aid of two diamine curing agents, namely, ethylenediamine and m-xylylenediamine. Polymers of the aromatic diepoxides showed transitions with peaks at ?56°C. and above +70°C. Three main peaks were registered for the aliphatic and fluorocarbon diepoxides: at ?125 and at ?100°C., at ?56°C., and at 0°C. It is suggested that the T_g is affected by an interdependence of relaxation of all components of the polymer main chain.     

The preparation and characterization of poly(urethane–peo-polar siloxane) complexes as polymer electrolytes

A series of novel poly(urethane-PEO-polar siloxane) copolymers and their complexes with LiClO₄ were prepared for assessment as polymer electrolytes and characterized by IR, GPC, and DSC, and their ionic conductivity and thermal stability were tested. The incorporation of polar siloxanes into U-PEO greatly increased conductivity. The highest conductivity was 2.6 × 10^?5 S cm^?1 at 25°C. The correlation between T_g, conductivity, and the ratio of siloxane to PEO as well as stability of the polymers are discussed. © 1995 John Wiley & Sons, Inc.     

Synthesis and Characterization of High Performance Poly(amide-imide)s based on a New Diimide-diacide and Various Diamines

A new diimide-diacid, (4-(4-(2,6-diphenylpyridin-4yl)phenoxy)phenyl)-1,3-bis(trimellitimidobenzene) (PPMIB), was synthesized from the condensation reaction of a new diamine, (4-(4-(2,6-diphenylpyridin-4yl)phenoxy)phenyl)-3,5-diaminobezamide (PPDA), and trimellitic anhydride carboxylic acid (TMAA) in glacial acetic acid. The diimide-diacid (PPMIB) was characterized by FT-IR, ¹H-NMR and elemental analysis. A series of novel aromatic poly(amide-imide)s (PAIs) was synthesized by using direct polycondensation of PPMIB with various diamines in NMP in the presence of triphenylposphite and pyridine as condensing agents. The resulting PAIs were amorphous, readily soluble in many polar aprotic solvents and showed inherent viscosities of 0.35–0.50 dL/g. According to thermal analysis, these polymers exhibited glass transition temperatures (T_gs) in the range of 202–280°C and temperature of 10% weight loss (T₁₀) varied from 400 to 545°C in N₂. These polymers in NMP solution exhibited strong UV-Vis absorption maxima at 320°C nm and their fluorescence emission peaks appeared around 410–565 nm.     

Polyimides from 1,5-bis(4-amino-2-trifluoromethylphenoxy)naphthalene and aromatic tetracarboxylic dianhydrides

A new trifluoromethylated bis(ether amine), 1,5-bis(4-amino-2-trifluoromethylphenoxy)naphthalene, was synthesized in two steps starting from 1,5-dihydroxynaphthalene and 2-chloro-5-nitrobenzotrifluoride via nucleophilic aromatic substitution and catalytic reduction. A series of novel fluorinated polyimides with moderate to high molecular weights were synthesized from the diamine with various aromatic tetracarboxylic dianhydrides using a conventional two-stage process. All polyimides could afford flexible and tough films and most of them were soluble in strong polar solvents such as N-methyl-2-pyrrolidone (NMP) and N,N-dimethylacetamide (DMAc). The polyimides showed glass-transition temperatures (T_g) in the range of 253-315 °C (by DSC) and softening temperatures (T_s) in the range of 250-300 °C (by TMA). Decomposition temperatures for 5% weight loss all occurred above 500 °C in both air and nitrogen atmospheres. The dielectric constants of these polymers ranged from 3.17 to 3.64 at 1 MHz. The properties of these fluorinated polyimides were also compared with those of polyimides prepared from 1,5-bis(4-aminophenoxy)naphthalene with the same dianhydrides.     

Synthesis and crosslinking of poly (aryl ether)s containing 1,1-diphenylethylene moieties

Poly (aryl ether)s containing the diphenylethylene moiety, synthesized from 1,1-bis(4-fluo-rophenyl)ethylene or 1,1-bis(4-hydroxyphenyl)ethylene, are thermally crosslinkable. Char-acterization and crosslinking studies of these polymers were carried out by GPC, DSC, TGA, and NMR. The solvent resistance and T_g's of the resulting crosslinked networks increase after crosslinking. Thermogravimetric analysis shows that no significant mass loss accompanies the crosslinking reaction. © 1995 John Wiley & Sons, Inc.     

Mesomorphic and luminescent properties of side chain nematic liquid-crystalline polymers containing Ir(III)

Iridium-containing liquid-crystalline polymers were obtained by graft copolymerisation using poly(methylhydrogeno)siloxane, 1-methyl-4-(4-(4-vinylcyclohexyl)cyclohexyl)benzene (M₁) and an iridium complexes monomer (Ir-M₂). The series of polymers contained different molecular fractions of Ir-M₂ from 0% to 1.2%. All of these polymers showed mesomorphic behaviours. The introduction of small amount of iridium ions endowed liquid-crystalline polymers with luminescent properties. The chemical structures were characterised by IR and ¹H NMR. The mesomorphic properties and phase behaviour were investigated by differential scanning calorimetry, thermal gravimetric analysis, polarising optical microscopy and X-ray diffraction. With an increase of iridium complexes units in the polymers, the glass transition temperature (T_g) did not change significantly; the isotropic temperature (T_i) decreased. All polymers showed typical nematic marble textures, which was confirmed by X-ray diffraction. The temperatures at which 5% weight loss occurred (T_d) were greater than 300°C for the polymers. The introduction of iridium complexes units did not change the liquid-crystalline state of polymer systems. With Ir³⁺ ion contents ranging between 0.6 and 2.4 mol%, luminescent intensity of polymers gradually increased.     

Synthesis and Properties of Polyamides and Polyimides Derived From Diamines Having 2-Phenyl-4,5-Oxazolediyl Units and Polyamide/Montmorillonite Composite

Aromatic polyamides were synthesized from 4,5-bis(4-aminophenyl)-2-phenyloxazole (APO) or 4,5-bis[4(4-aminophenoxy)phenyl]-2-phenyloxazole (APPO) containing 2-phenyl-4,5-oxazolediyl units with several aromatic carboxylic dichlorides by a low-temperature solution polycondensation method. The polyamides were obtained quantitatively, and their inherent viscosities ranged from 0.48 to 1.25 dL g^?1. The glass transition temperatures (T _gs) were displayed between 234 to 311°C, and the residual weight at 600°C (Res.wt₆₀₀) exceeded 52% in nitrogen atmosphere. The polyamides showed good solubility in several aprotic polar solvents, such as N,N-dimethylacetoamide (DMAc), N-methyl-2-pyrrolidone (NMP), and dimethyl sulfoxide (DMSO). Aromatic polyimides were derived from APO or APPO with aromatic carboxylic dianhydrides through polyamic acids. The inherent viscosities of the polyamic acids, which were 0.53 to 1.02 dL g^?1, T _gs of the polyimides were observed between 259 to 361°C and their Res.wts₆₀₀ were above 70%. The polyamides and polyimides were amorphous and afforded thin, flexible and tough films. We also prepared a nanocomposite of the polyamide derived from APPO with organophilic montmorillonite clay.     

New soluble aromatic polyamides containing ether linkages and laterally attached p-terphenyls

Two series of new polyamides containing flexible ether linkages and laterally attached side rods (3a-i and 4a-i) were synthesized from 2^′,5^′-bis(4-aminophenoxy)-[1,1^′;4^′,1^″]terphenyl (1a) and 2^′,5^′-bis(4-amino-2-trifluoromethylphenoxy)-[1,1^′;4^′,1^″]terphenyl (1b), respectively, with various aromatic dicarboxylic acids by the direct phosphorylation polycondensation. The polymers were produced with high yields and moderate to high inherent viscosities (0.41-0.97 dl/g) that corresponded to weight-average molecular weights (by size exclusion chromatography) of 47,000-65,000. Except for some polyamides that derived from rigid diacids, the obtained polyamides were readily soluble in aprotic polar solvents, such as N-methyl-2-pyrrolidone (NMP) and N,N-dimethylacetamide (DMAc), and could afford flexible and tough films via solvent casting. The polymer films cast from DMAc solutions possessed tensile strengths of 85-106 MPa and initial moduli of 1.82-2.96 GPa. These polyamides showed glass-transition temperatures (T_g) in the range of 206-263 °C (by DSC) and softening temperatures (T_s) in the range of 211-253 °C (by TMA). Decomposition temperatures (T_d) for 10% weight loss all occurred above 400 °C (by TGA) in both nitrogen and air atmospheres. The polyamides 4a-i derived from trifluoromethyl-substituted diamine 1b generally showed a higher solubility, T_g and T_s but lower thermal stability as compared to the analogous polyamides 3a-i based on diamine 1a.     

Oxyalkylene polymers with alkylsulfonylmethyl side chains: Gas barrier properties

Gas barrier properties of alkylsulfonylmethyl-substituted poly(oxyalkylene)s are discussed. Oxygen permeability coefficients of three methylsulfonylmethyl-substituted poly(oxyalkylene)s, poly[oxy(methylsulfonylmethyl)ethylene] (MSE), poly[oxy(methylsulfonylmethyl)ethylene-co-oxyethylene] (MSEE), and poly[oxy-2,2-bis (methylsulfonylmethyl)trimethylene oxide] (MST) were measured. MSEE, which has the most flexible backbone of the three polymers, had an oxygen permeability coefficient at 30°C of 0.0036 × 10⁻¹³ cm³(STP)·cm/cm²·s·Pa higher than that of MSE, 0.0014 × 10⁻¹³ cm³(STP)·cm/cm²·s·Pa, because the former polymer's T_g was near room temperature. MST with two polar groups per repeat unit and the highest T_g showed the highest oxygen permeability, 0.013 × 10⁻¹³ cm³(STP) · cm/cm²·s·Pa, among the three polymers, probably because steric hindrance between the side chains made the chain packing inefficient. As the side chain length of poly[oxy(alkylsulfonylmethyl)ethylene] increased, T_g and density decreased and the oxygen permeability coefficients increased. The oxygen permeability coefficient of MSE at high humidity (84% relative humidity) was seven times higher than when it was dry because absorbed water lowered its T_g. At 100% relative humidity MSE equilibrated to a T_g of 15°C after 2 weeks. A 50/50 blend of MSE/MST had oxygen barrier properties better than the individual polymers (O₂ permeability coefficient is 0.0007 × 10⁻¹³ cm³(STP)·cm/cm² ·s·Pa), lower than most commercial high barrier polymers. At 100% relative humidity, it equilibrated to a T_g of 42°C, well above room temperature. These are polymer systems with high gas barrier properties under both dry and wet conditions. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36 : 75–83, 1998     

Synthesis and characterization of aromatic polymers derived from 5‐perfluoroalkylisophthalic acid

A series of polyisophthalamides and polyisophthalates having perfluorinated side chains were prepared from 5‐perfluoroalkylisophthaloyl dichlorides. The aromatic polyamides and polyarylates synthesized by conventional low temperature solution polycondensation and interfacial polycondensation, respectively, had inherent viscosities of 0.19 to 1.28 dL g⁻¹ in yields of 65 to 100%. Solubilies of the resulting polymers were improved by incorporating nonafluorobutyl groups but not improved by incorporating heptadecafluorooctyl groups. Although the effect on the glass transition temperature (T_g) of incorporating perfluoroalkyl groups into the aromatic polyamides or polyarylate backbone is great, the incorporation maintained the thermal stability of the polymers. In spite of the rigid nature of perfluoroalkyl groups, T_gs were decreased by incorporating perfluoroalkyl groups. The value of the contact angle of water on the aromatic polyamides films gradually increased with incorporation of the perfluoroalkyl groups. On the other hand, the value of the contact angle remarkably increased when perfluoroalkyl groups were incorporated into polyarylates. The Owens γs were also calculated for some aromatic polyamides by measuring contact angles of diiodomethane on the polymer films. The γs were estimated at 23‐37 mN m⁻¹ and about 10% of them were contributed by hydrogen bonding. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1135–1141, 1999