Micro-column preconcentration/separation using thiacalix[4]arene tetracarboxylate derivative modified mesoporous TiO2 as packing materials on-line coupled to inductively coupled plasma optical emission spectrometry for the determination of trace heavy metals in environmental water samples

A novel adsorbent of thiacalix[4]arene tetracarboxylate derivative modified mesoporous TiO₂ was prepared and was used as a packing material for flow injection (FI) micro-column (20 mm × 4.0 mm i.d.) separation/preconcentration on-line coupled to inductively coupled plasma optical emission spectrometry (ICP-OES) simultaneous determination of trace metals (V, Cu, Pb, Cr) in environmental water samples. The experimental conditions for modified mesoporous TiO₂ packed micro-column separation/preconcentration of the target metals were optimized and the interference of commonly coexisting ions was examined. The adsorption capacities of thiacalix[4]arene tetracarboxylate derivative modified mesoporous TiO₂ for V, Cu, Pb and Cr were found to be 14.0, 11.7, 17.7 and 14.5 mg g^− 1, respectively. The detection limits of the method were 0.09, 0.23, 0.50 and 0.15 µg L^− 1 for V, Cu, Pb and Cr, respectively, with a preconcentration factor of 20. The precision of this method were 1.7% (V), 3.9% (Cu), 4.6% (Pb) and 2.9% (Cr) (n = 7, C = 5 µg L^− 1), respectively. The developed method was applied to the determination of trace heavy metals in real samples and the recoveries for spiked samples were found to be in the range of 88.7-107.1%. For validation, a certified reference material of GSBZ50009-88 environmental water sample was analyzed and the determined values were in good agreement with the certified values.     

Mesoporous TiO2 aerogel for selective enrichment of phosphopeptides in rat liver mitochondria

The enrichment of low abundance phosphopeptides before MS analysis is a critical step for in-depth phosphoproteome research. In this study, mesoporous titanium dioxide (TiO₂) aerogel was prepared by precipitation and supercritical drying. The specific surface area up to 490.7 m² g⁻¹ is achieved by TiO₂ aerogel, much higher than those obtained by commercial TiO₂ nanoparticles and by the latest reported mesoporous TiO₂ spheres. Due to the large specific surface area and the mesoporous structure of the aerogel, the binding capacity for phosphopeptides is six times higher than that of conventional TiO₂ microparticles (173 vs 28 μmol g⁻¹). Because of the good compatibility of enrichment procedure with MALDI-TOF-MS and the large binding capacity of TiO₂ aerogel, a detection limit as low as 30 amol for analyzing phosphopeptides in β-casein digest was achieved. TiO₂ aerogel was further applied to enrich phosphopeptides from rat liver mitochondria, and 266 unique phosphopeptides with 340 phosphorylation sites, corresponding to 216 phosphoprotein groups, were identified by triplicate nanoRPLC-ESI-MS/MS runs, with false-positive rate less than 1% at the peptide level. These results demonstrate that TiO₂ aerogel is a kind of promising material for sample pretreatment in the large-scale phosphoproteome study.     

Synthesis and photocatalytic activity of co-doped mesoporous TiO2 on Brij98/CTAB composite surfactant template

Using composite surfactant templates, polyoxyethylene (20) oleyl ether (Brij98) and cetyl trimethyl ammonium bromide (CTAB), as structure-directing agents, N and La co-doped mesoporous TiO₂ complex photocatalysts were synthesized successfully. The micromorphology of co-doped mesoporous TiO₂ samples was characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier transformed infrared spectroscopy (FT-IR), energy-dispersive X-ray spectrometer (EDS) and N₂ adsorption-desorption measurements. The results indicated that the complex photocatalyst prepared with a molar ratio of Brij98:CTAB=1:1 showed a uniform pore size of ca. 7 nm and a high specific surface area (S_BET) of 279.0 m² g⁻¹, and exhibited the highest photocatalytic activity for degradation of papermaking wastewater under ultra-violet light irradiation. The chemical oxygen demand (CODc_r) percent degradation was about 73% in 12 h and chroma percent degradation was 100% in 8 h.     

Development of mesoporous TiO2 microspheres with high specific surface area for selective enrichment of phosphopeptides by mass spectrometric analysis

In this study, mesoporous TiO₂ microspheres were synthesized by simple hydrothermal reaction, and successfully developed for phosphopeptides enrichment from both standard protein digestion and real biological sample such as rat brain tissue extract. The mesoporous TiO₂ microspheres (the diameter size of about 1.0 μm) obtained by simple hydrothermal method were found to have a specific surface area of 84.98 m²/g, which is much larger than smooth TiO₂ microspheres with same size. The surface area of mesoporous TiO₂ microspheres is almost two times of commercial TiO₂ nanoparticle (a diameter of 90 nm). Using standard proteins digestion and real biological samples, the superior selectivity and capacity of mesoporous TiO₂ microspheres for the enrichment of phosphorylated peptides than that of commercial TiO₂ nanoparticles and TiO₂ microspheres was also observed. It has been demonstrated that mesoporous TiO₂ microspheres have powerful potential for selective enrichment of phosphorylated peptides. Moreover, the preparation of the mesoporous TiO₂ microspheres obtained by the hydrothermal reaction is easy, simple and low-cost. These mesoporous TiO₂ microspheres with the ability of large scale synthesis can widely be applied for phosphorylated proteomic research.     

Novel low humidity sensor made of TiO(2) nanowires/poly(2-acrylamido-2-methylpropane sulfonate) composite material film combined with quartz crystal microbalance

A novel ceramic nanowires of TiO₂ and poly(2-acrylamido-2-methylpropane sulfonate) (TiO₂ NWs/PAMPS) composite material films coated on quartz crystal microbalance (QCM) was prepared as a low humidity sensor. The 50 wt.% of TiO₂ NWs/PAMPS composite material films showed excellent sensitivity (2.63 −ΔHz/Δppm_v) at 31.5 ppm_v), linearity (R² = 0.9959) and acceptable response time (64 s at 34.6 ppm_v). The low humidity sensing mechanism was discussed in terms of surface texture and nanostructured morphology of the composite materials. Moreover, the adsorption dynamic analysis, molecular mechanics calculation (association constant), was used to elucidate the effect of adding 50 wt.% TiO₂ NWs into PAMPS in the increased sensitivity of low humidity sensing.     

Synthesis and photocatalytic activity for water-splitting reaction of nanocrystalline mesoporous titania prepared by hydrothermal method

Nanocrystalline mesoporous TiO₂ was synthesized by hydrothermal method using titanium butoxide as starting material. XRD, SEM, and TEM analyses revealed that the synthesized TiO₂ had anatase structure with crystalline size of about 8 nm. Moreover, the synthesized titania possessed a narrow pore size distribution with average pore diameter and high specific surface area of 215 m²/g. The photocatalytic activity of synthesized TiO₂ was evaluated with photocatalytic H₂ production from water-splitting reaction. The photocatalytic activity of synthesized TiO₂ treated with appropriate calcination temperature was considerably higher than that of commercial TiO₂ (Ishihara ST-01). The utilization of mesoporous TiO₂ photocatalyst with high crystallinity of anatase phase promoted great H₂ production. Furthermore, the reaction temperature significantly influences the water-splitting reaction.     

Preparation and characterization of SiO2/TiO2 composite microspheres with microporous SiO2 core/mesoporous TiO2 shell

SiO₂/TiO₂ composite microspheres with microporous SiO₂ core/mesoporous TiO₂ shell structures were prepared by hydrolysis of titanium tetrabutylorthotitanate (TTBT) in the presence of microporous silica microspheres using hydroxypropyl cellulose (HPC) as a surface esterification agent and porous template, and then dried and calcined at different temperatures. The as-prepared products were characterized with differential thermal analysis and thermogravimetric (DTA/TG), scanning electron microscopy (SEM), X-ray diffraction (XRD), nitrogen adsorption. The results showed that composite particles were about 1.8 μm in diameter, and had a spherical morphology and a narrow size distribution. Uniform mesoporous titania coatings on the surfaces of microporous silica microspheres could be obtained by adjusting the HPC concentration to an optimal concentration of about 3.2 mmol L⁻¹. The anatase and rutile phase in the SiO₂/TiO₂ composite microspheres began to form at 700 and 900 °C, respectively. At 700 °C, the specific surface area and pore volume of the SiO₂/TiO₂ composite microspheres were 552 and 0.652 mL g⁻¹, respectively. However, at 900 °C, the specific surface area and pore volume significantly decreased due to the phase transformation from anatase to rutile.     

Preconcentration of trace elements from water samples on a minicolumn of yeast (Yamadazyma spartinae) immobilized TiO2 nanoparticles for determination by ICP-AES

A trace element preconcentration procedure is described utilizing a minicolumn of yeast (Yamadazyma spartinae) immobilized TiO₂ nanoparticles for determination of Cr, Cu, Fe, Mn, Ni and Zn from water samples by inductively coupled plasma atomic emission spectrometry. The elements were quantitatively retained on the column between pH 6 and 8. Elution was made with 5% (v/v) HNO₃ solution. Recoveries ranged from 98 ± 2 (Cr) to 100 ± 4 (Zn) for preconcentration of 50 mL multielement solution (50 μg L⁻¹). The column made up of 100 mg sorbent (yeast immobilized TiO₂ NP) offers a capacity to preconcentrate up to 500 mL of sample solution to achieve an enrichment factor of 250 with 2 mL of 5% (v/v) HNO₃ eluent. The detection limits obtained from preconcentration of 50 mL blank solutions (5%, v/v, HNO₃, n = 11) were 0.17, 0.45, 0.25, 0.15, 0.33 and 0.10 μg L⁻¹ for Cr, Cu, Fe, Mn, Ni and Zn, respectively. Relative standard deviation (RSD) for five replicate analyses was better than 5%. The retention of the elements was not affected from up to 500 μg L⁻¹ Na⁺ and K⁺ (as chlorides), 100 μg L⁻¹ Ca²⁺ (as nitrate) and 50 μg L⁻¹ Mg²⁺ (as sulfate). The method was validated by analysis of freshwater standard reference material (SRM 1643e) and applied to the determination of the elements from tap water and lake water samples.     

Highly ordered Zn-doped mesoporous silica: An efficient catalyst for transesterification reaction

Designing highly ordered material with nanoscale periodicity is of great significance in the field of solid state chemistry. Herein, we report the synthesis of highly ordered 2D-hexagonal mesoporous zinc-doped silica using a mixture of anionic and cationic surfactants under hydrothermal conditions. Powder XRD, N₂ sorption, TEM analysis revealed highly ordered 2D-hexagonal arrangements of the pores with very good surface area (762 m² g⁻¹) in this Zn-rich mesoporous material. Chemical analysis shows very high loading of zinc (ca. 12.0 wt%) in the material together with retention of hexagonal pore structure. Interestingly, high temperature calcination resulted into zinc silicate phase, unlike any ZnO phase, which otherwise is expected under heat treatments. High surface area together with Zn loading in this mesoporous material has been found useful for the catalytic activity of the materials in the acid-catalyzed transesterification reactions of various esters under mild liquid phase conditions.     

Mesoporous TiO2 nanoparticles for highly sensitive solid-phase microextraction of organochlorine pesticides

Mesoporous TiO₂ nanoparticles were synthesized with the hydrothermal method and characterized by powder X-ray diffraction (PXRD) and transmission electron microscope (TEM). Then a superior solid-phase microextraction (SPME) fiber was fabricated by sequentially coating the stainless steel fiber with silicone sealant film and mesoporous TiO₂ powder. The developed fiber possessed a homogeneous surface and a long life-span up to 100 times at direct immersing (DI) extraction mode. Under the optimized conditions, the extraction efficiencies of the self-made 17 μm TiO₂ fiber for six organochlorine pesticides (OCPs) were higher than those of the two commercial fibers (65 μm PDMS/DVB and 85 μm PA fibers) which were much thicker than the former. As for analytical performance, low detection limits (0.08–0.60 ng L⁻¹) and wide linearity (5–5000 ng L⁻¹) were achieved under the optimal conditions. The repeatabilities (n = 5) for single fiber were between 2.8 and 12.3%, while the reproducibilities (n = 3) of fiber-to-fiber were in the range of 3.7–15.7%. The proposed fiber was successfully applied to the sensitive analysis of OCPs in real water samples and four of the six analytes were detected from the rainwater and the lake water samples.     

Titania-lanthanum phosphate photoactive and hydrophobic new generation catalyst

Titania-lanthanum phosphate nanocomposites with multifunctional properties have been synthesized by aqueous sol-gel method. The precursor sols with varying TiO₂:LaPO₄ ratios were applied as thin coating on glass substrates in order to be transparent, hydrophobic, photocatalytically active coatings. The phase compositions of the composite powders were identified by powder X-ray diffraction (XRD) and high-resolution transmission electron microscopy (HR-TEM). The anatase phase of TiO₂ in TiO₂-LaPO₄ composite precursors was found to be stable even on annealing at 800 °C. The glass substrates, coated with TL1 (TiO₂-LaPO₄ composition with 1 mol% LaPO₄) and TL50 (composite precursor containing TiO₂ and LaPO₄ with molar ratio 1:1) sols and annealed at 400 °C, produced contact angles of 74° and 92°, respectively, though it is only 62° for pure TiO₂ coating. The glass substrates, coated with TL50 sol, produced surfaces with relatively high roughness and uneven morphology. The TL1 material, annealed at 800 °C, has shown the highest UV photoactivity with an apparent rate constant, k_app=24×10⁻³ min⁻¹, which is over five times higher than that observed with standard Hombikat UV 100 (k_app=4×10⁻³ min⁻¹). The photoactivity combined with a moderate contact angle (85.3°) shows that this material has a promise as an efficient self-cleaning precursor.     

Change in mechanistic pathway of hydroboration: A detailed kinetic study of H2BBr·SMe2 and HBBr2·SMe2

Hydroboration reactions of 1-octene and 1-hexyne with H₂BBr·SMe₂ in CH₂Cl₂ were studied as a function of concentration and temperature, using ¹¹B NMR spectroscopy. The reactions exhibited saturation kinetics. The rate of dissociation of dimethyl sulfide from boron at 25 °C was found to be (7.36 ± 0.59 and 7.32 ± 0.90) × 10⁻³ s⁻¹ for 1-octene and 1-hexyne, respectively. The second order rate constants, k₂, for hydroboration worked out to be 7.00 ± 0.81 M s⁻¹ and 7.03 ± 0.70 M s⁻¹, while the overall composite second order rate constants, k K, were (3.30 ± 0.43 and 3.10 ± 0.37) × 10⁻² M s⁻¹, respectively at 25 °C. The entropy and enthalpy values were found to be large and positive for k₁, whilst for k₂ these were large and negative, with small values for enthalpies. This is indicative of a limiting dissociative (D) for the dissociation of Me₂S and associative mechanism (A) for the hydroboration process. The overall activation parameters, ΔH^≠ and ΔS^≠, were found to be 98 ± 2 kJ mol⁻¹ and +56 ± 7 J K⁻¹ mol⁻¹ for 1-octene whilst, in the case of 1-hexyne these were found out to be 117 ± 7 kJ mol⁻¹ and +119 ± 24 J K⁻¹ mol⁻¹, respectively. When comparing the kinetic data between H₂BBr·SMe₂ and HBBr₂·SMe₂, the results showed that the rate of dissociation of Me₂S from H₂BBr·SMe₂ is on average 34 times faster than it is in the case of HBBr₂·SMe₂. Similarly, the rate of hydroboration with H₂BBr·SMe₂ was found to be on average 11 times faster than it is with HBBr₂·SMe₂. It is also clear that by replacing a hydrogen substituent with a bromine atom in the case of H₂BBr·SMe₂ the mechanism for the overall process changes from limiting dissociative (D) to interchange associative (I_a).     

Sol–gel synthesis of macro–mesoporous titania monoliths and their applications to chromatographic separation media for organophosphate compounds

We have developed a method of independently tailoring the macro- and mesoporous structures in titania (TiO₂) monoliths in order to achieve liquid chromatographic separations of phosphorous-containing compounds. Anatase TiO₂ monolithic gels with well-defined bicontinuous macropores and microstructured skeletons are obtained via the sol–gel process in strongly acidic conditions using poly(ethylene oxide) as a phase separator and N-methylformamide as a proton scavenger. Aging treatment of the wet gels in the mother liquor at temperatures of 100–200 °C and subsequent heat treatment at 400 °C allow the formation and control of mesoporous structures with uniform pore size distributions in the gel skeletons, without disturbing the preformed macroporous morphology. The monolithic TiO₂ rod columns with bimodal macro–mesoporous structures possess the phospho-sensitivity and exhibit excellent chromatographic separations of phosphorus-containing compounds.     

Enthalpy change and mechanism of oxidation of o-phenylenediamine by hydrogen peroxide catalyzed by horseradish peroxidase

The hydrogen peroxide-oxidation of o-phenylenediamine (OPD) catalyzed by horseradish peroxidase (HRP) at 37 °C in 50 mM phosphate buffer (pH 7.0) was studied by calorimetry. The apparent molar reaction enthalpy with respect to OPD and hydrogen peroxide were −447 ± 8 kJ mol⁻¹ and −298 ± 9 kJ mol⁻¹, respectively. Oxidation of OPD by H₂O₂ catalyzed by HRP (1.25 nM) at pH 7.0 and 37 °C follows a ping-pong mechanism. The maximum rate V_max (0.91 ± 0.05 μM s⁻¹), Michaelis constant for OPD K_m,S (51 ± 3 μM), Michaelis constant for hydrogen peroxide Km,H₂O₂ (136 ± 8 μM), the catalytic constant k_cat (364 ± 18 s⁻¹) and the second-order rate constants k₊₁ = (2.7 ± 0.3) × 10⁶ M⁻¹ s⁻¹ and k₊₅ = (7.1 ± 0.8) × 10⁶ M⁻¹ s⁻¹ were obtained by the initial rate method.     

CTAB-assisted synthesis of mesoporous F-N-codoped TiO2 powders with high visible-light-driven catalytic activity and adsorption capacity

This article describes the preparation of mesoporous rod-like F-N-codoped TiO₂ powder photocatalysts with anatase phase via a sol-gel route at the temperature of 373 K, using cetyltrimethyl ammonium bromide (CTAB) as surfactant. The as-prepared photocatalysts were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and UV-visible diffuse reflectance spectra (UV-vis DRS). The results showed that the photocatalysts possessed a homogeneous pore diameter and a high surface area of 106.3-160.7 m³ g⁻¹. The increasing CTAB reactive concentration extended the visible-light absorption up to 600 nm. The F-N-codoped TiO₂ powders exhibited significant higher adsorption capacity for methyl orange (MO) than that of Degussa P25 and showed more than 6 times higher visible-light-induced catalytic degradation for MO than that of P25.     

Mechanistic investigation of the thermal decomposition of Biphen(OPi-Pr)PtEt2: An entrance into C-C single bond activation?

Biphen(OPi-Pr) and (COD)PtCl₂ give Biphen(OPi-Pr)PtCl₂ which upon treating with ethyl Grignard forms Biphen(OPi-Pr)PtEt₂. The thermal decomposition of Biphen(OPi-Pr)PtEt₂ was investigated in the temperature range of 353-383 K. The clean and quantitative formation of the Pt(Ethene) adduct was observed. X-ray structures of a molecule in the solid state of all three reaction products and two further related complexes with phenyl fingers instead of i-Pr have been determined. For the complexes with i-Pr fingers a decisive deviation from a square plane is observed in contrast to the complexes with phenyl fingers. The P-Pt-P angle increases from about 95° in Biphen(OPi-Pr)PtCl₂ to about 120° in Biphen(OPi-Pr)Pt(Ethene), forcing the bridging C-C single bond of the biphenyl fragment as near as 4.17 Å to the Pt center. No through-space coupling between the bridging C atoms and the Pt center could be observed in ¹³C NMR spectroscopy. No bond lengthening of the bridging C-C single bond in the biphenyl fragment was observed in Biphen(OPi-Pr)Pt(Ethene) in comparison to the precursor complexes. The thermal decomposition of Biphen(OPi-Pr)PtEt₂ can be described by a first-order kinetic and the activation parameters were determined (temperature range: 353-383 K; ΔH^‡ = 173.8 ± 16.2 kJ/mol and ΔS^‡ = 104.7 ± 44.1 J/(mol K)). The reaction kinetics were also measured for perdeuterated ethyl groups yielding in a kinetic isotopic effect of 1.56 ± 0.14 which was almost temperature-independent. Selective deuteration at α and β position of the ethyl group, respectively, showed that β-H elimination takes place fast in comparison to the complete thermolysis. In the temperature range of 333-353 K only a scrambling of the deuterium atoms was found without further decomposition (temperature range: 333-353 K; Δ_scramH^‡ = 76.1 ± 15.2 kJ/mol, Δ_scramS^‡ = −80.7 ± 45.5 J/(mol K) for Biphen(OPi-Pr)PtEt₂-d⁶). The ethene is not lost during the scrambling process. The scrambling process is connected with a primary KIE decisively larger than 1.56. Biphen(OPi-Pr)Pt(Ethene) exchanges the coordinated ethene with ethene in solution as proven by labeling experiments. Both a dissociative and an associative mechanism could be shown to take place as ethene exchange reaction by means of VT¹H NMR spectroscopy via line shape analysis (temperature range: 333-373 K; Δ_assH^‡ = 26.9 ± 29.6 kJ/mol, Δ_assS^‡ = −148.0 ± 87.5 J/(mol K), Δ_dissH^‡ = 86.0 ± 6.5 kJ/mol, Δ_dissS^‡ = 5.4 ± 17.8 J/(mol K)). The Pt(0) complex formed during the dissociative loss of ethene activates several substrates among them: O₂, H₂, H₂SiPh₂ via Si-H activation, MeI presumably via forming a cationic methyl adduct and ethane via C-H activation but it was proven that the bridging C-C single bond of the biphenyl fragment is not even temporarily broken. The materials were characterized by means of ¹H NMR, ¹³C NMR, ³¹P NMR, ¹⁹⁵Pt NMR, EA, MS, IR, X-ray analysis and polarimetric measurement where necessary.     

Study of binding and denaturation dynamics of IgG and anti-IgG using dual color fluorescence correlation spectroscopy

In this article, we present a systematic study on IgG and Fab fragment of anti-IgG molecules using fluorescence auto- and cross-correlation spectroscopy to investigate their diffusion characteristics, binding kinetics, and the effect of small organic molecule, urea on their binding. Through our analysis, we found that the diffusion coefficient for IgG and Fab fragment of anti-IgG molecules were 37 ± 2 μm² s⁻¹ and 56 ± 2 μm² s⁻¹, respectively. From the binding kinetics study, the respective forward (k_a) and backward (k_d) reaction rates were (5.25 ± 0.25) × 10⁶ M⁻¹ s⁻¹ and 0.08 ± 0.005 s⁻¹, respectively and the corresponding dissociation binding constant (K_D) was 15 ± 2 nM. We also found that urea inhibits the binding of these molecules at 4 M concentration due to denaturation.     

Mixed conductivity, structural and microstructural characterization of titania-doped yttria tetragonal zirconia polycrystalline/titania-doped yttria stabilized zirconia composite anode matrices

Taking advantage of the fact that TiO₂ additions to 8YSZ cause not only the formation of a titania-doped YSZ solid solution but also a titania-doped YTZP solid solution, composite materials based on both solutions were prepared by solid state reaction. In particular, additions of 15 mol% of TiO₂ give rise to composite materials constituted by 0.51 mol fraction titania-doped yttria tetragonal zirconia polycrystalline and 0.49 mol fraction titania-doped yttria stabilized zirconia (0.51TiYTZP/0.49TiYSZ). Furthermore, Y₂(Ti_1−yZr_y)₂O₇ pyrochlore is present as an impurity phase with y close to 1, according to FT-Raman results. Lower and higher additions of titania than that of 15 mol%, i.e., x=0, 5, 10, 20, 25 and 30 mol% were considered to study the evolution of 8YSZ phase as a function of the TiO₂ content. Furthermore, zirconium titanate phase (ZrTiO₄) is detected when the titania content is equal or higher than 20 mol% and this phase admits Y₂O₃ in solid solution according to FE-SEM-EDX.The 0.51TiYTZP/0.49TiYSZ duplex material was selected in this study to establish the mechanism of its electronic conduction under low oxygen partial pressures. In the pO₂ range from 0.21 to 10^−7.5 atm. the conductivity is predominantly ionic and constant over the range and its value is 0.01 S/cm. The ionic plus electronic conductivity is 0.02 S/cm at 1000 °C and 10^−12.3 atm. Furthermore, the onset of electronic conductivity under reducing conditions exhibits a −1/4 pO₂ dependence. Therefore, it is concluded that the n-type electronic conduction in the duplex material can be due to a small polaron-hopping between Ti³⁺ and Ti⁴⁺.     

Preparation of titania microfiltration membranes supported on porous Ti–Al alloys

A TiO₂ membrane supported on a planar porous Ti–Al alloy was prepared by combination of electrophoretic deposition and dip-coating. In the electrophoretic deposition process, the membrane thickness increased linearly with the square root of the deposition time, while increased with decrease of the suspension viscosity. The perfect TiO₂/Ti–Al composite membrane was obtained by further dip-coating modification. SEM images showed that the surface of the membrane was defect-free. XRD result indicated that rutile TiO₂ still remained in the membrane bulk as the main phase, while a new phase titanium oxides with the form of Ti_xO_y, where y is less than 2x, was also observed. The supported TiO₂/Ti–Al composite membrane had an average pore size of 0.28 μm, a thickness of 40 μm or so and a pure water flux of 3037 L m⁻² h⁻¹ bar⁻¹.     

Cobalt as internal standard for arsenic and selenium determination in urine by simultaneous atomic absorption spectrometry

The effectiveness of internal standardization for simultaneous atomic absorption spectrometry (SIMAAS) was investigated for As and Se determination in urine. Co and Sn were selected as internal standard (IS) candidates based on the evaluation of some physico-chemical parameters related to the atomization. Correlation graphs, plotted from the normalized absorbance signals (n = 20) of internal standard (axis y) versus analyte (axis x), precision, and accuracy of the analytical results were the supportive parameters to choose Co as the most appropriate IS. The urine samples were diluted 1 + 2 to 1.0% (v/v) HNO₃ + 80 μg L⁻¹ Co²⁺. The mixture 20 μg Pd + 3 μg Mg was used as chemical modifier and the optimized temperatures for pyrolysis and atomization steps were 1400 and 2300 °C, respectively. The characteristic masses for As (47 ± 1 pg) and Se (72 ± 2 pg) were estimated from the analytical curves. The detection limits (n = 20, 3δ) were 1.8 ± 0.1 and 2.6 ± 0.1 μg L⁻¹ for As and Se, respectively. The reliability of the entire procedure was checked with the analysis of certified reference material from Sero AS(Seronorm™ Trace Elements in Urine). The obtained results showed the matrix interference disallowed the instrument calibration with aqueous standards. The best analytical condition was achieved when matrix-matched standards were used in combination with Co as IS, which improved the recoveries obtained for As. Under this experimental condition, eight urine samples were analysed and spiked with 10 and 25 μg L⁻¹ As and Se. The mean recoveries were 96 ± 6% (10 μg L⁻¹ As), 95 ± 6% (25 μg L⁻¹ As), 101 ± 7% (10 μg L⁻¹ Se), and 97 ± 4% (25 μg L⁻¹ Se).